Give FIFO writes the same treatment as reads to avoid fixed costs of
individual transfers on a slow bus (e.g., tcan4x5x).

Link: https://lore.kernel.org/r/20210817050853.14875-4-matt@bitbashing.ioSigned-off-by: Matt Kline <matt@bitbashing.io>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

On peripherals communicating over a relatively slow SPI line
(e.g. tcan4x5x), individual transfers have high fixed costs.
This causes the driver to spend most of its time waiting between
transfers and severely limits throughput.

Reduce these overheads by reading more than one word at a time.
Writing could get a similar treatment in follow-on commits.

Link: https://lore.kernel.org/r/20210817050853.14875-3-matt@bitbashing.ioSigned-off-by: Matt Kline <matt@bitbashing.io>
[mkl: remove __packed from struct id_and_dlc]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

If FIFO reads or writes fail due to the underlying regmap (e.g., SPI)
I/O, propagate that up to the m_can driver, log an error, and disable
interrupts, similar to the mcp251xfd driver.

While reworking the FIFO functions to add this error handling,
add support for bulk reads and writes of multiple registers.

Link: https://lore.kernel.org/r/20210817050853.14875-2-matt@bitbashing.ioSigned-off-by: Matt Kline <matt@bitbashing.io>
[mkl: re-wrap long lines, remove WARN_ON, convert to netdev block comments]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch fixes the commenting style in the m_can driver.

Fixes: 1be37d3b ("can: m_can: fix periph RX path: use rx-offload to ensure skbs are sent from softirq context")
Fixes: df06fd67 ("can: m_can: m_can_chip_config(): enable and configure internal timestamps")
Link: https://lore.kernel.org/r/20210819111703.599686-2-mkl@pengutronix.de
Cc: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

This patch removes a stray empty line in the cdev_to_priv() function.

Fixes: ac33ffd3 ("can: m_can: let m_can_class_allocate_dev() allocate driver specific private data")
Link: https://lore.kernel.org/r/20210819111703.599686-1-mkl@pengutronix.deSigned-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

CANFD block on RZ/G2L SoC is almost identical to one found on
R-Car Gen3 SoC's. On RZ/G2L SoC interrupt sources for each channel
are split into different sources and the IP doesn't divide (1/2)
CANFD clock within the IP.

This patch adds compatible string for RZ/G2L family and splits
the irq handlers to accommodate both RZ/G2L and R-Car Gen3 SoC's.

Link: https://lore.kernel.org/r/20210727133022.634-3-prabhakar.mahadev-lad.rj@bp.renesas.comSigned-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
[mkl: fixed typo: recieve -> receive, thanks Geert]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Add CANFD binding documentation for Renesas RZ/G2L SoC.

Link: https://lore.kernel.org/r/20210727133022.634-2-prabhakar.mahadev-lad.rj@bp.renesas.comSigned-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

With the patch 07ff4aed ("time/timecounter: Mark 1st argument of
timecounter_cyc2time() as const") some instances of the struct
mcp251xfd_priv can be marked as const. This patch marks these as
const.

Link: https://lore.kernel.org/r/20210813091027.159379-1-mkl@pengutronix.de
Cc: Manivannan Sadhasivam <mani@kernel.org>
Cc: Thomas Kopp <thomas.kopp@microchip.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The documentation of struct es58x_fd_tx_conf_msg explains in details
the different TDC parameters. However, those description are redundant
with the documentation of struct can_tdc.

Remove most of the description.

Also, fixes a typo in the reference to the datasheet (E701 -> E70).

Link: https://lore.kernel.org/r/20210815033248.98111-8-mailhol.vincent@wanadoo.frSigned-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Adding myself (Vincent Mailhol) as a maintainer for the ETAS ES58X
CAN/USB driver.

Link: https://lore.kernel.org/r/20210814093353.74391-1-mailhol.vincent@wanadoo.frSigned-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The sanity checks on the control modes will reject any request related
to an unsupported features, even turning it off.

Example on an interface which does not support CAN-FD:

$ ip link set can0 type can bitrate 500000 fd off
RTNETLINK answers: Operation not supported

This patch lets such command go through (but requests to turn on an
unsupported feature are, of course, still denied).

Link: https://lore.kernel.org/r/20210815033248.98111-2-mailhol.vincent@wanadoo.frSigned-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

For CAN buses to work, a termination resistor has to be present at both
ends of the bus. This resistor is usually 120 Ohms, other values may be
required for special bus topologies.

This patch adds support for a generic GPIO based CAN termination. The
resistor value has to be specified via device tree, and it can only be
attached to or detached from the bus. By default the termination is not
active.

Link: https://lore.kernel.org/r/20210818071232.20585-4-o.rempel@pengutronix.deSigned-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Enable termination-* binding and provide validation example for it.

Link: https://lore.kernel.org/r/20210818071232.20585-3-o.rempel@pengutronix.deSigned-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Some boards provide GPIO controllable termination resistor. Provide
binding to make use of it.

Link: https://lore.kernel.org/r/20210818071232.20585-2-o.rempel@pengutronix.deSigned-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

Matthias Fuchs's and Thomas Körper's email addresses aren't valid
anymore. Use the newly created role account instead.

Link: https://lore.kernel.org/r/20210809175843.207864-1-mkl@pengutronix.de
Cc: socketcan@esd.eu
Cc: Stefan Mätje <Stefan.Maetje@esd.eu>
Acked-by: Stefan Mätje <stefan.maetje@esd.eu>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

The ARRAY_SIZE macro is defined to get an array's size which is
more compact and more formal in linux source. Thus, we can replace
the long sizeof(arr)/sizeof(arr[0]) with the compact ARRAY_SIZE.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20210817121106.44189-1-wangborong@cdjrlc.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Currently, the declaration of fill_imix_distribution() is dependent
on CONFIG_XFRM. This is incorrect.

Move fill_imix_distribution() declaration out of #ifndef CONFIG_XFRM
block.
Signed-off-by: Nick Richardson <richardsonnick@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add gfp_t mask as an input parameter to mem_cgroup_charge_skmem(),
to give more control to the networking stack and enable it to change
memcg charging behavior. In the future, the networking stack may decide
to avoid oom-kills when fallbacks are more appropriate.

One behavior change in mem_cgroup_charge_skmem() by this patch is to
avoid force charging by default and let the caller decide when and if
force charging is needed through the presence or absence of
__GFP_NOFAIL.
Signed-off-by: Wei Wang <weiwan@google.com>
Reviewed-by: Shakeel Butt <shakeelb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

VLAN TCI is a 16 bit field which includes Priority(3 bits),
CFI(1 bit) and VID(12 bits). Currently ntuple filters support
installing rules to steer packets based on VID only.
This patch extends that support such that filters can
be installed for entire VLAN TCI.
Signed-off-by: Subbaraya Sundeep <sbhatta@marvell.com>
Signed-off-by: Sunil Goutham <sgoutham@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit 09e856d5 ("vrf: Reset skb conntrack connection on VRF rcv")
fixes the "reverse-DNAT" of an SNAT-ed packet over a VRF.

This patch adds a test for this scenario.
Signed-off-by: Lahav Schlesinger <lschlesinger@drivenets.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is only one caller for ops_free(), so inline it.
Separate net_drop_ns() and net_free(), so the net_free()
can be called directly.
Add free_exit_list() helper function for free net_exit_list.

====================
v2:
 - v1 does not apply, rebase it.
====================
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for tag_sja1105 running on non-sja1105 DSA ports, by making
sure that every time we dereference dp->priv, we check the switch's
dsa_switch_ops (otherwise we access a struct sja1105_port structure that
is in fact something else).

This adds an unconditional build-time dependency between sja1105 being
built as module => tag_sja1105 must also be built as module. This was
there only for PTP before.

Some sane defaults must also take place when not running on sja1105
hardware. These are:

- sja1105_xmit_tpid: the sja1105 driver uses different VLAN protocols
  depending on VLAN awareness and switch revision (when an encapsulated
  VLAN must be sent). Default to 0x8100.

- sja1105_rcv_meta_state_machine: this aggregates PTP frames with their
  metadata timestamp frames. When running on non-sja1105 hardware, don't
  do that and accept all frames unmodified.

- sja1105_defer_xmit: calls sja1105_port_deferred_xmit in sja1105_main.c
  which writes a management route over SPI. When not running on sja1105
  hardware, bypass the SPI write and send the frame as-is.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Bongsu Jeon says:

====================
Update the virtual NCI device driver and add the NCI testcase

This series updates the virtual NCI device driver and NCI selftest code
and add the NCI test case in selftests.

1/8 to use wait queue in virtual device driver.
2/8 to remove the polling code in selftests.
3/8 to fix a typo.
4/8 to fix the next nlattr offset calculation.
5/8 to fix the wrong condition in if statement.
6/8 to add a flag parameter to the Netlink send function.
7/8 to extract the start/stop discovery function.
8/8 to add the NCI testcase in selftests.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the NCI testcase reading T4T Tag that has NFC TEST in plain text.
the virtual device application acts as T4T Tag in this testcase.
Signed-off-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To reuse the start/stop discovery code in other testcase, extract the code.
Signed-off-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To reuse the send_cmd_mt_nla for NLM_F_REQUEST and NLM_F_DUMP flag,
add the flags parameter to the function.
Signed-off-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

memcpy should be executed only in case nla_len's value is greater than 0.
Signed-off-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

nlattr could have a padding for 4 bytes alignment. So next nla's offset
should be calculated with a padding.
Signed-off-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix typo: rep_len -> resp_len
Signed-off-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Because the virtual NCI device uses Wait Queue, the virtual device
application doesn't need to poll the NCI frame.
Signed-off-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In previous version, the user level virtual device application that used
this driver should have the polling scheme to read a NCI frame.
To remove this polling scheme, use Wait Queue.
Signed-off-by: Bongsu Jeon <bongsu.jeon@samsung.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add seq_puts() statement for dev_mcast, make it more readable.
As also, keep vertical alignment for {dev, ptype, dev_mcast} that
under /proc/net.
Signed-off-by: Yajun Deng <yajun.deng@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>

Make all dependent RxRPC kconfig entries be dependent on AF_RXRPC
so that they are presented (indented) after AF_RXRPC instead
of being presented at the same level on indentation.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: David Howells <dhowells@redhat.com>
Cc: Marc Dionne <marc.dionne@auristor.com>
Cc: linux-afs@lists.infradead.org
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: netdev@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>

Mat Martineau says:

====================
mptcp: Add full mesh path manager option

The path manager in MPTCP controls the creation of additional subflows
after the initial connection is created. As each peer advertises
available endpoints with the ADD_ADDR MPTCP option, the recipient of
those advertisements must decide which subflows to create from the known
local and remote interfaces that are available for use by MPTCP.

The existing in-kernel path manager will create one additional subflow
when an ADD_ADDR is received, or a local address is newly configured for
MPTCP use. The maximum number of subflows has a configurable limit.

This patch set adds a MPTCP_PM_ADDR_FLAG_FULLMESH flag to the MPTCP
netlink API that enables subflows to be created more aggressively. When
an ADD_ADDR is received from a peer, new subflows are created between
that address/port and all local addresses configured for MPTCP.
Similarly, when a new local address is newly configured for use by
MPTCP, new subflows are created between that local address and all known
remote addresses for that MPTCP connection. The configurable limit on
the number of subflows still applies. If the new flag is not used the
path manager behavior is unchanged.

Patch 1 adds a helper function and refactors another function to prepare
for the rest of the patch series.

Patches 2 and 3 add two mesh connection capabilities: initiating
subflows based on added local addresses, or reacting to incoming
advertisements.

Patches 4-6 add full mesh cases to the self tests.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The removing addresses testcases can only deal with the continuous ids.
This patch added the uncontinuous removing ids support.
Signed-off-by: Geliang Tang <geliangtang@xiaomi.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch added the testcases for the fullmesh address flag of the path
manager.
Co-developed-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Matthieu Baerts <matthieu.baerts@tessares.net>
Signed-off-by: Geliang Tang <geliangtang@xiaomi.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch dealt with the MPTCP_PM_ADDR_FLAG_FULLMESH flag in add_addr()
and print_addr(), to set and print out the fullmesh flag.
Signed-off-by: Geliang Tang <geliangtang@xiaomi.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In mptcp_pm_nl_add_addr_received(), fill a temporary allocate array of
all local address corresponding to the fullmesh endpoint. If such array
is empty, keep the current behavior.

Elsewhere loop on such array and create a subflow for each local address
towards the given remote address
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@xiaomi.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch added and managed a new per endpoint flag, named
MPTCP_PM_ADDR_FLAG_FULLMESH.

In mptcp_pm_create_subflow_or_signal_addr(), if such flag is set, instead
of:
        remote_address((struct sock_common *)sk, &remote);
fill a temporary allocated array of all known remote address. After
releaseing the pm lock loop on such array and create a subflow for each
remote address from the given local.

Note that the we could still use an array even for non 'fullmesh'
endpoint: with a single entry corresponding to the primary MPC subflow
remote address.
Suggested-by: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Geliang Tang <geliangtang@xiaomi.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch added a new helper mptcp_pm_get_flags_and_ifindex_by_id(),
and used it in __mptcp_subflow_connect() to get the flags and ifindex
values.

Then the two arguments flags and ifindex of __mptcp_subflow_connect()
can be dropped.
Signed-off-by: Geliang Tang <geliangtang@xiaomi.com>
Signed-off-by: Mat Martineau <mathew.j.martineau@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>