Due to change to switch to use lock_sock inside rfcomm_sk_state_change
the socket shutdown/release procedure can cause a deadlock:

    rfcomm_sock_shutdown():
      lock_sock();
      __rfcomm_sock_close():
        rfcomm_dlc_close():
          __rfcomm_dlc_close():
            rfcomm_dlc_lock();
            rfcomm_sk_state_change():
              lock_sock();

To fix this when the call __rfcomm_sock_close is now done without
holding the lock_sock since rfcomm_dlc_lock exists to protect
the dlc data there is no need to use lock_sock in that code path.

Link: https://lore.kernel.org/all/CAD+dNTsbuU4w+Y_P7o+VEN7BYCAbZuwZx2+tH+OTzCdcZF82YA@mail.gmail.com/
Fixes: b7ce436a ("Bluetooth: switch to lock_sock in RFCOMM")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Address resolution will be paused during active scan to allow any
advertising reports reach the host. If LL privacy is enabled,
advertising will rely on the controller to generate new RPA.

If host is not using RPA, there is no need to stop advertising during
active scan because there is no need to generate RPA in the controller.
Signed-off-by: Zhengping Jiang <jiangzp@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Add a new PID/VID 0e8d/0608 for MT7921K chip found on AMD RZ608 module.

From /sys/kernel/debug/usb/devices:
T:  Bus=01 Lev=02 Prnt=02 Port=01 Cnt=01 Dev#=  3 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0e8d ProdID=0608 Rev= 1.00
S:  Manufacturer=MediaTek Inc.
S:  Product=Wireless_Device
S:  SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=125us
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=8a(I) Atr=03(Int.) MxPS=  64 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS=  64 Ivl=125us
I:  If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=8a(I) Atr=03(Int.) MxPS=  64 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS=  64 Ivl=125us
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Add VID 13D3 & PID 3583 for MediaTek MT7921 USB Bluetooth chip.

The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.

T:  Bus=03 Lev=02 Prnt=02 Port=02 Cnt=01 Dev#=  3 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=13d3 ProdID=3583 Rev= 1.00
S:  Manufacturer=MediaTek Inc.
S:  Product=Wireless_Device
S:  SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=125us
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=8a(I) Atr=03(Int.) MxPS=  64 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS=  64 Ivl=125us
I:  If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

syzbot is again reporting attempt to cancel uninitialized work
at mgmt_index_removed() [1], for setting of HCI_MGMT flag from
mgmt_init_hdev() from hci_mgmt_cmd() from hci_sock_sendmsg() can
race with testing of HCI_MGMT flag from mgmt_index_removed() from
hci_sock_bind() due to lack of serialization via hci_dev_lock().

Since mgmt_init_hdev() is called with mgmt_chan_list_lock held, we can
safely split hci_dev_test_and_set_flag() into hci_dev_test_flag() and
hci_dev_set_flag(). Thus, in order to close this race, set HCI_MGMT flag
after INIT_DELAYED_WORK() completed.

This is a local fix based on mgmt_chan_list_lock. Lack of serialization
via hci_dev_lock() might be causing different race conditions somewhere
else. But a global fix based on hci_dev_lock() should deserve a future
patch.

Link: https://syzkaller.appspot.com/bug?extid=844c7bf1b1aa4119c5de
Reported-by: syzbot+844c7bf1b1aa4119c5de@syzkaller.appspotmail.com
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Fixes: 3f2893d3 ("Bluetooth: don't try to cancel uninitialized works at mgmt_index_removed()")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

HarrrisonPeak, CyclonePeak, SnowFieldPeak and SandyPeak controllers
are marked to support HCI_QUIRK_LE_STATES.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Chethan T N <chethan.tumkur.narayan@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Hardware variant for Magnetor core (CNVi) is added.
Signed-off-by: Kiran K <kiran.k@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Add VID 13D3 & PID 3578 for MediaTek MT7921 USB Bluetooth chip.

The information in /sys/kernel/debug/usb/devices about the Bluetooth
device is listed as the below.

T:  Bus=03 Lev=01 Prnt=01 Port=07 Cnt=03 Dev#=  5 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=13d3 ProdID=3578 Rev= 1.00
S:  Manufacturer=MediaTek Inc.
S:  Product=Wireless_Device
S:  SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=125us
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=8a(I) Atr=03(Int.) MxPS=  64 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS=  64 Ivl=125us
I:  If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Co-developed-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Chris Lu <chris.lu@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Recent changes breaks HCIGETDEVINFO since it changes the size of
hci_dev_info.

Fixes: 26afbd82 ("Bluetooth: Add initial implementation of CIS connections")
Reported-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

hci_read_buffer_size_sync shall not use HCI_OP_LE_READ_BUFFER_SIZE_V2
sinze that is LE specific, instead it is hci_le_read_buffer_size_sync
version that shall use it.

Link: https://bugzilla.kernel.org/show_bug.cgi?id=216382
Fixes: 26afbd82 ("Bluetooth: Add initial implementation of CIS connections")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This introduces a "Mesh UUID" and an Experimental Feature bit to the
hdev mask, and depending all underlying Mesh functionality on it.
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

The patch adds state bits, storage and HCI command chains for sending
and receiving Bluetooth Mesh advertising packets, and delivery to
requesting user space processes. It specifically creates 4 new MGMT
commands and 2 new MGMT events:

MGMT_OP_SET_MESH_RECEIVER - Sets passive scan parameters and a list of
AD Types which will trigger Mesh Packet Received events

MGMT_OP_MESH_READ_FEATURES - Returns information on how many outbound
Mesh packets can be simultaneously queued, and what the currently queued
handles are.

MGMT_OP_MESH_SEND - Command to queue a specific outbound Mesh packet,
with the number of times it should be sent, and the BD Addr to use.
Discrete advertisments are added to the ADV Instance list.

MGMT_OP_MESH_SEND_CANCEL - Command to cancel a prior outbound message
request.

MGMT_EV_MESH_DEVICE_FOUND - Event to deliver entire received Mesh
Advertisement packet, along with timing information.

MGMT_EV_MESH_PACKET_CMPLT - Event to indicate that an outbound packet is
no longer queued for delivery.
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

WMT cmd/event doesn't follow up the generic HCI cmd/event handling, it
needs constantly polling control pipe until the host received the WMT
event, thus, we should require to specifically acquire PM counter on the
USB to prevent the interface from entering auto suspended while WMT
cmd/event in progress.

Fixes: a1c49c43 ("Bluetooth: btusb: Add protocol support for MediaTek MT7668U USB devices")
Co-developed-by: Jing Cai <jing.cai@mediatek.com>
Signed-off-by: Jing Cai <jing.cai@mediatek.com>
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

A new Bluetooth device for the Realtek RTW8852AE has been noted.

This device has the following lsusb output:

Bus 001 Device 003: ID 0cb8:c549 Opticis Co., Ltd Bluetooth Radio

The pertinent part of /sys/kernel/debug/usb/devices is as follows:

T: Bus=01 Lev=01 Prnt=01 Port=03 Cnt=02 Dev#= 3 Spd=12 MxCh= 0
D: Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=0cb8 ProdID=c549 Rev= 0.00
S: Manufacturer=Realtek
S: Product=Bluetooth Radio
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms
I: If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms
I: If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 17 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 17 Ivl=1ms
I: If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 25 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 25 Ivl=1ms
I: If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 33 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 33 Ivl=1ms
I: If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E: Ad=03(O) Atr=01(Isoc) MxPS= 49 Ivl=1ms
E: Ad=83(I) Atr=01(Isoc) MxPS= 49 Ivl=1ms
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

T:  Bus=01 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=7392 ProdID=c611 Rev= 2.00
S:  Manufacturer=Realtek
S:  Product=Edimax Bluetooth Adapter
S:  SerialNumber=XXXXXXXXXXXX
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: Szabolcs Sipos <labuwx@balfug.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Based on photos available from the FCC, all currently supported RTL8761B
series USB dongles have the same chip: RTL8761BUV.

rtl8761bu is often used to refer to this chip.
rtl8761b sometimes refers to this chip, and other times to its
UART variant (RTL8761BTV).

+----------------+---------+---------+---------------+
|     Dongle     | USB VID | USB PID |    FCC ID     |
+----------------+---------+---------+---------------+
| ASUS USB-BT500 | 0x0b05  | 0x190e  | MSQ-USBBTJB00 |
| TP-Link UB500  | 0x2357  | 0x0604  | 2AXJ4UB500    |
| EDUP EP-B3519  |         |         | 2AHRD-EPB3519 |
| EDUP EP-B3536  |         |         | 2AHRDEP-B3536 |
| UGREEN CM390   |         |         | 2AQI5-CM390   |
+----------------+---------+---------+---------------+
Signed-off-by: Szabolcs Sipos <labuwx@balfug.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Add the support ID(0x13D3, 0x3592) to usb_device_id table for
Realtek RTL8852C.

The device info from /sys/kernel/debug/usb/devices as below.

T:  Bus=03 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#=  2 Spd=12   MxCh= 0
D:  Ver= 1.00 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=13d3 ProdID=3592 Rev= 0.00
S:  Manufacturer=Realtek
S:  Product=Bluetooth Radio
S:  SerialNumber=00e04c000001
C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=500mA
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=1ms
E:  Ad=02(O) Atr=02(Bulk) MxPS=  64 Ivl=0ms
E:  Ad=82(I) Atr=02(Bulk) MxPS=  64 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
Signed-off-by: Max Chou <max.chou@realtek.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

hci_abort_conn() is a wrapper around a number of DISCONNECT and
CREATE_CONN_CANCEL commands that was being invoked from hci_request
request queues, which are now deprecated. There are two versions:
hci_abort_conn() which can be invoked from the hci_event thread, and
hci_abort_conn_sync() which can be invoked within a hci_sync cmd chain.
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

The HCI_OP_READ_ENC_KEY_SIZE command is converted from using the
deprecated hci_request mechanism to use hci_send_cmd, with an
accompanying hci_cc_read_enc_key_size to handle it's return response.
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

When disconnecting all devices, hci_conn_failed is used to cleanup
hci_conn object when the hci_conn object cannot be aborted.
The function hci_conn_failed requires the caller holds hdev->lock.

Fixes: 9b3628d7 ("Bluetooth: hci_sync: Cleanup hci_conn if it cannot be aborted")
Signed-off-by: Zhengping Jiang <jiangzp@google.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.

Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

To prevent multiple conn complete events, we shouldn't look up the
conn with hci_lookup_le_connect, since it requires the state to be
BT_CONNECT. By the time the duplicate event is processed, the state
might have changed, so we end up processing the new event anyway.

Change the lookup function to hci_conn_hash_lookup_ba.

Fixes: d5ebaa7c ("Bluetooth: hci_event: Ignore multiple conn complete events")
Signed-off-by: Archie Pusaka <apusaka@chromium.org>
Reviewed-by: Sonny Sasaka <sonnysasaka@chromium.org>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

In order to properly handle shutdown syscall the code shall not assume
that the how argument is always SHUT_RDWR resulting in SHUTDOWN_MASK as
that would result in poll to immediately report EPOLLHUP instead of
properly waiting for disconnect_cfm (Disconnect Complete) which is
rather important for the likes of BAP as the CIG may need to be
reprogrammed.

Fixes: ccf74f23 ("Bluetooth: Add BTPROTO_ISO socket type")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

syzbot is reporting double kfree() at remove_adv_monitor() [1], for
commit 7cf5c297 ("Bluetooth: hci_sync: Refactor remove Adv
Monitor") forgot to remove duplicated mgmt_pending_remove() when
merging "if (err) {" path and "if (!pending) {" path.

Link: https://syzkaller.appspot.com/bug?extid=915a8416bf15895b8e07 [1]
Reported-by: syzbot <syzbot+915a8416bf15895b8e07@syzkaller.appspotmail.com>
Fixes: 7cf5c297 ("Bluetooth: hci_sync: Refactor remove Adv Monitor")
Signed-off-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Get Device Flags don't check if device does actually use an RPA in which
case it shall only set HCI_CONN_FLAG_REMOTE_WAKEUP if LL Privacy is
enabled.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This attempts to fix the follow errors:

In function 'memcmp',
    inlined from 'bacmp' at ./include/net/bluetooth/bluetooth.h:347:9,
    inlined from 'l2cap_global_chan_by_psm' at
    net/bluetooth/l2cap_core.c:2003:15:
./include/linux/fortify-string.h:44:33: error: '__builtin_memcmp'
specified bound 6 exceeds source size 0 [-Werror=stringop-overread]
   44 | #define __underlying_memcmp     __builtin_memcmp
      |                                 ^
./include/linux/fortify-string.h:420:16: note: in expansion of macro
'__underlying_memcmp'
  420 |         return __underlying_memcmp(p, q, size);
      |                ^~~~~~~~~~~~~~~~~~~
In function 'memcmp',
    inlined from 'bacmp' at ./include/net/bluetooth/bluetooth.h:347:9,
    inlined from 'l2cap_global_chan_by_psm' at
    net/bluetooth/l2cap_core.c:2004:15:
./include/linux/fortify-string.h:44:33: error: '__builtin_memcmp'
specified bound 6 exceeds source size 0 [-Werror=stringop-overread]
   44 | #define __underlying_memcmp     __builtin_memcmp
      |                                 ^
./include/linux/fortify-string.h:420:16: note: in expansion of macro
'__underlying_memcmp'
  420 |         return __underlying_memcmp(p, q, size);
      |                ^~~~~~~~~~~~~~~~~~~

Fixes: 332f1795 ("Bluetooth: L2CAP: Fix l2cap_global_chan_by_psm regression")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This attempts to fix suspend performance when there is no connections by
not updating the event mask.

Fixes: ef61b6ea ("Bluetooth: Always set event mask on suspend")
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Commit c8992cff ("Bluetooth: hci_event: Use of a function table to
handle Command Complete") was (presumably) meant to only refactor things
without any functional changes.

But it does have one undesirable side-effect, before *status would always
be set to skb->data[0] and it might be overridden by some of the opcode
specific handling. While now it always set by the opcode specific handlers.
This means that if the opcode is not known *status does not get set any
more at all!

This behavior change has broken bluetooth support for BCM4343A0 HCIs,
the hci_bcm.c code tries to configure UART attached HCIs at a higher
baudraute using vendor specific opcodes. The BCM4343A0 does not
support this and this used to simply fail:

[   25.646442] Bluetooth: hci0: BCM: failed to write clock (-56)
[   25.646481] Bluetooth: hci0: Failed to set baudrate

After which things would continue with the initial baudraute. But now
that hci_cmd_complete_evt() no longer sets status for unknown opcodes
*status is left at 0. This causes the hci_bcm.c code to think the baudraute
has been changed on the HCI side and to also adjust the UART baudrate,
after which communication with the HCI is broken, leading to:

[   28.579042] Bluetooth: hci0: command 0x0c03 tx timeout
[   36.961601] Bluetooth: hci0: BCM: Reset failed (-110)

And non working bluetooth. Fix this by restoring the previous
default "*status = skb->data[0]" handling for unknown opcodes.

Fixes: c8992cff ("Bluetooth: hci_event: Use of a function table to handle Command Complete")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

hci_update_adv_data() is called from hci_event and hci_core due to
events from the controller. The prior function used the deprecated
hci_request method, and the new one uses hci_sync.c
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This function has no dependencies on the deprecated hci_request
mechanism, so has been moved unchanged to hci_sync.c
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

This patch deletes a whole bunch of code no longer reached because the
functionality was recoded using hci_sync.c
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

The Advertising Instance expiration timer adv_instance_expire was
handled with the deprecated hci_request mechanism, rather than it's
replacement: hci_sync.
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Recoding HCI cmds to offload SCO codec to use hci_sync mechanism rather
than deprecated hci_request mechanism.
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

hci_req_stop_discovery has been deprecated in favor of
hci_stop_discovery_sync() as part of transition to hci_sync.c
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

le_scan_restart delayed work queue was running as a deprecated
hci_request instead of on the newer thread-safe hci_sync mechanism.
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

The le_scan_disable timeout was being performed on the deprecated
hci_request.c mechanism.  This timeout is performed in hci_sync.c
Signed-off-by: Brian Gix <brian.gix@intel.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Tested on HP Envy ey0xxx

output from /sys/kernel/debug/usb/devices:

T:  Bus=01 Lev=01 Prnt=01 Port=02 Cnt=01 Dev#=  2 Spd=480  MxCh= 0
D:  Ver= 2.10 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs=  1
P:  Vendor=0489 ProdID=e0e0 Rev= 1.00
S:  Manufacturer=MediaTek Inc.
S:  Product=Wireless_Device
S:  SerialNumber=000000000
C:* #Ifs= 3 Cfg#= 1 Atr=e0 MxPwr=100mA
A:  FirstIf#= 0 IfCount= 3 Cls=e0(wlcon) Sub=01 Prot=01
I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=81(I) Atr=03(Int.) MxPS=  16 Ivl=125us
E:  Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E:  Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 1 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   0 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   0 Ivl=1ms
I:  If#= 1 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=   9 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=   9 Ivl=1ms
I:  If#= 1 Alt= 2 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  17 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  17 Ivl=1ms
I:  If#= 1 Alt= 3 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  25 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  25 Ivl=1ms
I:  If#= 1 Alt= 4 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  33 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  33 Ivl=1ms
I:  If#= 1 Alt= 5 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  49 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  49 Ivl=1ms
I:  If#= 1 Alt= 6 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb
E:  Ad=83(I) Atr=01(Isoc) MxPS=  63 Ivl=1ms
E:  Ad=03(O) Atr=01(Isoc) MxPS=  63 Ivl=1ms
I:* If#= 2 Alt= 0 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=8a(I) Atr=03(Int.) MxPS=  64 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS=  64 Ivl=125us
I:  If#= 2 Alt= 1 #EPs= 2 Cls=e0(wlcon) Sub=01 Prot=01 Driver=(none)
E:  Ad=8a(I) Atr=03(Int.) MxPS= 512 Ivl=125us
E:  Ad=0a(O) Atr=03(Int.) MxPS= 512 Ivl=125us
Signed-off-by: Fae <faenkhauser@gmail.com>
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>

Use try_cmpxchg instead of cmpxchg (*ptr, old, new) == old in
napi_if_scheduled_mark_missed. x86 CMPXCHG instruction returns
success in ZF flag, so this change saves a compare after cmpxchg
(and related move instruction in front of cmpxchg).

Also, try_cmpxchg implicitly assigns old *ptr value to "old" when cmpxchg
fails, enabling further code simplifications.

Cc: Eric Dumazet <edumazet@google.com>
Cc: Paolo Abeni <pabeni@redhat.com>
Signed-off-by: Uros Bizjak <ubizjak@gmail.com>
Link: https://lore.kernel.org/r/20220822143243.2798-1-ubizjak@gmail.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Petr Machata says:

====================
mlxsw: Remove some unused code

This patchset removes code that is not used anymore after the following two
commits removed all users:

- commit b0d80c01 ("mlxsw: Remove Mellanox SwitchX-2 ASIC support")
- commit 9b43fbb8 ("mlxsw: Remove Mellanox SwitchIB ASIC support")
====================

Link: https://lore.kernel.org/r/cover.1661350629.git.petrm@nvidia.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Function mlxsw_core_port_type_get() is no longer used. So remove it.
Signed-off-by: Jiri Pirko <jiri@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: Petr Machata <petrm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>