For drivers that don't actually flush their queues when
aggregation stop with the IEEE80211_AMPDU_TX_STOP_FLUSH
or IEEE80211_AMPDU_TX_STOP_FLUSH_CONT reasons is done,
like iwlwifi or iwlegacy, mac80211 can then transmit on
a TID that the driver still considers busy. This happens
in the following way:

 - IEEE80211_AMPDU_TX_STOP_FLUSH requested
 - driver marks TID as emptying
 - mac80211 removes tid_tx data, this can copy packets
   to the TX pending queues and also let new packets
   through to the driver
 - driver gets unexpected TX as it wasn't completely
   converted to the new API

In iwlwifi, this lead to the following warning:

WARNING: at drivers/net/wireless/iwlwifi/dvm/tx.c:442 iwlagn_tx_skb+0xc47/0xce0
Tx while agg.state = 4
Modules linked in: [...]
Pid: 0, comm: kworker/0:0 Tainted: G        W   3.1.0 #1
Call Trace:
 [<c1046e42>] warn_slowpath_common+0x72/0xa0
 [<c1046f13>] warn_slowpath_fmt+0x33/0x40
 [<fddffa17>] iwlagn_tx_skb+0xc47/0xce0 [iwldvm]
 [<fddfcaa3>] iwlagn_mac_tx+0x23/0x40 [iwldvm]
 [<fd8c98b6>] __ieee80211_tx+0xf6/0x3c0 [mac80211]
 [<fd8cbe00>] ieee80211_tx+0xd0/0x100 [mac80211]
 [<fd8cc176>] ieee80211_xmit+0x96/0xe0 [mac80211]
 [<fd8cc578>] ieee80211_subif_start_xmit+0x348/0xc80 [mac80211]
 [<c1445207>] dev_hard_start_xmit+0x337/0x6d0
 [<c145eee9>] sch_direct_xmit+0xa9/0x210
 [<c14462c0>] dev_queue_xmit+0x1b0/0x8e0

Fortunately, solving this problem is easy as the station
is being destroyed, so such transmit packets can only
happen due to races. Instead of trying to close the race
just let the race not reach the drivers by making two
changes:
 1) remove the explicit aggregation session teardown in
    the managed mode code, the same thing will be done
    when the station is removed, in __sta_info_destroy.
 2) When aggregation stop with AGG_STOP_DESTROY_STA is
    requested, leave the tid_tx data around as stopped.
    It will be cleared and freed in cleanup_single_sta
    later, but until then any racy packets will be put
    onto the tid_tx pending queue instead of transmitted
    which is fine since the station is being removed.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Since drivers can support several BSS / P2P Client
interfaces, the rssi callback needs to inform the driver
about the interface teh rssi event relates to.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

To be able to implement NS response offloading (in
regular operation or while in WoWLAN) drivers need
to know the IPv6 addresses assigned to interfaces.
Implement an IPv6 notifier in mac80211 to call the
driver when addresses change.

Unlike for IPv4, implement it as a callback rather
than as a list in the BSS configuration, that is
more flexible.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

A lot of the aggregation messages don't indicate the
station so they're hard to understand if there are
multiple sessions in progress. Make that easier by
adding the MAC address to most messages. Also add
the TID if it wasn't already there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Depending on the driver, having ARP filtering for
some addresses may be possible. Remove the logic
that tracks whether ARP filter is enabled or not
and give the driver the total number of addresses
instead of the length of the list so it can make
its own decision.
Reviewed-by: Luciano Coelho <coelho@ti.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

There are hardwares which support offload of data packets
for example when auto ARP is enabled the hw will send
the ARP response. In such cases if WEP encryption is
configured the hw must know the default WEP key in order
to encrypt the packets correctly.

When hw_accel is enabled and encryption type is set to WEP,
the driver should get the default key index from mac80211.
Signed-off-by: Yoni Divinsky <yoni.divinsky@ti.com>
[cleanups, fixes, documentation]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Some new APIs will require tracing a chandef without
it being part of a channel context, so separate out
the tracing macros for that.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

To ease further DFS development regarding interface combinations, use
the interface combinations structure to test for radar capabilities.
Drivers can specify which channel widths they support, and in which
modes. Right now only a single AP interface is allowed, but as the
DFS code evolves other combinations can be enabled.
Signed-off-by: Simon Wunderlich <siwu@hrz.tu-chemnitz.de>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The NL80211_ATTR_USE_MFP attribute was originally added for
NL80211_CMD_ASSOCIATE, but it is actually as useful (if not even more
useful) with NL80211_CMD_CONNECT, so process that attribute with the
connect command, too.
Signed-off-by: Jouni Malinen <jouni@qca.qualcomm.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

As per email discussion Jouni Malinen pointed out that:

"P2P message exchanges can be executed on the current operating channel
of any operation (both P2P and non-P2P station). These can be on 5 GHz
and even on 60 GHz (so yes, you _can_ do GO Negotiation on 60 GHz).

As an example, it would be possible to receive a GO Negotiation Request
frame on a 5 GHz only radio and then to complete GO Negotiation on that
band. This can happen both when connected to a P2P group (through client
discoverability mechanism) and when connected to a legacy AP (assuming
the station receive Probe Request frame from full scan in the beginning
of P2P device discovery)."

This means that P2P messages can be sent over different radio devices.
However, these should use the same P2P device address so it should be
able to provision this from user-space. This patch adds a parameter for
this to struct vif_params which should only be used during creation of
the P2P device interface.

Cc: Jouni Malinen <j@w1.fi>
Cc: Greg Goldman <ggoldman@broadcom.com>
Cc: Jithu Jance <jithu@broadcom.com>
Signed-off-by: Arend van Spriel <arend@broadcom.com>
[add error checking]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Add the nl80211_mesh_power_mode enumeration which holds possible
values for the mesh power mode. These modes are unknown, active,
light sleep and deep sleep.

Add power_mode entry to the mesh config structure to hold the
user-configured default mesh power mode. This value will be used
for new peer links.

Add the dot11MeshAwakeWindowDuration value to the mesh config.
The awake window is a duration in TU describing how long the STA
will stay awake after transmitting its beacon in PS mode.

Add access routines to:
 - get/set local link-specific power mode (STA)
 - get remote STA's link-specific power mode (STA)
 - get remote STA's non-peer power mode (STA)
 - get/set default mesh power mode (mesh config)
 - get/set mesh awake window duration (mesh config)

All config changes may be done at mesh runtime and take effect
immediately.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Signed-off-by: Ivan Bezyazychnyy <ivan.bezyazychnyy@gmail.com>
Signed-off-by: Mike Krinkin <krinkin.m.u@gmail.com>
[fix commit message line length, error handling in set station]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Move the default mesh beacon interval and DTIM period to cfg80211
and make them accessible to nl80211. This enables setting both
values when joining an MBSS.

Previously the DTIM parameter was not set by mac80211 so the
driver's default value was used.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

This functions will be used for mesh beacons, too.
Signed-off-by: Marco Porsch <marco@cozybit.com>
[some formatting fixes]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The established peer link count is indicated in mesh beacons and
used for other internal tasks. Previously it was not updated when
authenticated peering is performed in userspace.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Acked-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Ranges are taken from IEEE 802.11-2012, common sense or current
implementation requirements.
Signed-off-by: Marco Porsch <marco@cozybit.com>
Acked-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Allow mesh interface to disable the power save which is by default
turn on in certain chipset. Testing with 2 units of ZCN-1523H-5-16
featuring AR9280 chipset which have power save enabled by default.
Constant reset if the average signal of the peer mesh STA is below
-80 dBm and power save is enabled.
Signed-off-by: Chun-Yeow Yeoh <yeohchunyeow@gmail.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When the driver's resume function can't completely
restore the configuration in the device, it returns
1 from the callback which will be treated like a HW
restart request, but done directly.

In this case, also call the driver's restart_complete()
function so it can finish the reconfiguration there.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

My commit 529ba6e9
("mac80211: clean up association better in suspend")
introduced a bug when resuming from WoWLAN when a
device reset is desired. This case must not use the
suspend_bss_conf as it hasn't been stored.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When building the 80211 DocBook, scripts/kernel-doc reports
the following type of warnings:

Warning(include/net/cfg80211.h:334): No description found for return value of 'cfg80211_get_chandef_type'

These warnings are only reported when scripts/kernel-doc
runs in verbose mode.

To fix these use "Return:" to describe function return values.
Signed-off-by: Yacine Belkadi <yacine.belkadi.1@gmail.com>
[adjust for freq_reg_info() change]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The reg_notifier()'s return value need not be checked
as it is only supposed to do post regulatory work and
that should never fail. Any behaviour to regulatory
that needs to be considered before cfg80211 does work
to a driver should be specified by using the already
existing flags, the reg_notifier() just does post
processing should it find it needs to.

Also make lbs_reg_notifier static.
Signed-off-by: Luis R. Rodriguez <mcgrof@do-not-panic.com>
[move lbs_reg_notifier to not break compile]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

commit 1a919318 "regulatory: code cleanup"
changed is_ht40_allowed without considering that IEEE80211_CHAN_NO_HT40 is
not just one flag, but two.
This is causing HT40- to be blocked completely.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

My commit 4bf88530
("mac80211: convert to channel definition struct")
accidentally broke HT40 connections due to swapped
channel flag checks -- fix that.
Reported-by: Sujith Manoharan <sujith@msujith.org>
Tested-by: Sujith Manoharan <sujith@msujith.org>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

My commit 379b82f4
("regulatory: pass new regdomain to reset function")
broke the restore_regulatory_settings() function due
to a logic change. Consider this change:

-	reset_regdomains(true);
-	cfg80211_regdomain = cfg80211_world_regdom;
+	reset_regdomains(true, cfg80211_world_regdom);

This looks innocent enough, until you realise that the
called function (reset_regdomains) also resets the
cfg80211_world_regdom pointer, so that the old version
of the code would use the new object it pointed to and
the new version of the code uses the old object. This
lead to a double-free of this object.

Since reset_regdomains() sets it to &world_regdom, use
that directly.
Reported-by: Sujith Manoharan <sujith@msujith.org>
Tested-by: Sujith Manoharan <sujith@msujith.org>
Reported-by: Bob Copeland <me@bobcopeland.com>
Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The uevent callback doesn't protect its access to
last_request, which now causes a warning since
the conversion to get_last_request(). Fix this by
allowing to use RCU protection for last_request.
Reported-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

A beacon period starts at TSF time 0. Spoof this by
rounding the starting beacon time to a multiple of the
beacon interval, and keep TBTT aligned on TSF adjustment.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

For testing various timing-sensitive protocols (power
save, MBCA, etc.), a beacon accuracy of jiffies is not
sufficient. A tasklet_hrtimer is used for the beacon since
it runs the callback in soft-IRQ context with hrtimer
resolution.

Also handle BSS_CHANGED_BEACON_ENABLED for hwsim.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
[simplify timer container_of]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Make hwsim TSF offset adjustments cumulative and relative
to the fake PHY TSF. Now adding 1000us, then adding -1000us
doesn't result in a tsf_offset of -1000. Also the beacon
timestamp can now correctly be expressed as (tsf +
data->tsf_offset), which will be done in a later patch.
Signed-off-by: Thomas Pedersen <thomas@cozybit.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

One of the function names was wrong and some parameters were
missing.
Signed-off-by: Bob Copeland <me@bobcopeland.com>
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The following changes are invalid and should be
disallowed when a station already exists:
 * supported rates changes, except for TDLS peers
 * listen interval changes
 * HT capability changes

Disallow them and also update a mac80211 comment
explaining how they would be racy.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When an interface is configured to a 20 MHz channel
and the device as well as the peer are 40 MHz capable
the HT capabilities of the peer are not restricted to
20 MHz, even though they're supposed to be restricted
to the currently possible capabilities.

Unset the 40 MHz HT capability bits in this case.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Use __aligned(...) instead of __attribute__((aligned(...)))
in mac80211 and cfg80211.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Support the HT notify channel width action frame
to update the rate scaling about the bandwidth
the peer can receive in.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Use __packed instead of __attribute__((packed)).
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

When TX aggregation is stopped, there are a few
different cases:
 - connection with the peer was dropped
 - session stop was requested locally
 - session stop was requested by the peer
 - connection was dropped while a session is stopping

The behaviour in these cases should be different, if
the connection is dropped then the driver should drop
all frames, otherwise the frames may continue to be
transmitted, aggregated in the case of a locally
requested session stop or unaggregated in the case of
the peer requesting session stop.

Split these different cases so that the driver can
act accordingly; however, treat local and remote stop
the same way and ask the driver to not send frames as
aggregated packets any more.

In the case of connection drop, the stop callback the
driver is otherwise supposed to call is no longer
required.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

To call it from ___ieee80211_stop_tx_ba_session,
move the function and dependencies up.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Create the function ieee80211_remove_tid_tx to call
it from ___ieee80211_stop_tx_ba_session later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

The initiator/tx doesn't really identify why an
aggregation session is stopped, give a reason
for stopping that more clearly identifies what's
going on. This will help tell the driver clearly
what is expected of it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Today, stations are added already associated. That is
inefficient if, for example, the driver has no room
for stations any more because then the station will
go through the entire auth/assoc handshake, only to
be kicked out afterwards.

To address this a bit better, at least with drivers
using the new station state callback, allow hostapd
to add stations in unauthenticated mode, just after
receiving the AUTH frame, before even replying. Thus
if there's no more space at that point, it can send
a negative auth frame back. It still needs to handle
later state transition errors though, of course.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

Some AP code ended up in mlme.c as ap.c didn't
exist when it was written, move it now.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

In interoperability testing some APs showed bad behaviour
if some of the VHT capabilities of the station are better
than their own. Restrict the assoc request parameters
 - beamformee capabable,
 - RX STBC and
 - RX MCS set
to the subset that the AP can support.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>