- 21 May, 2016 9 commits
-
-
Arnd Bergmann authored
The added support for SPI mode made it possible to configure the driver when I2C is disabled, leaving an unused device table: drivers/rtc/rtc-rv3029c2.c:794:29: error: 'rv3029_id' defined but not used [-Werror=unused-variable] This moves the table inside of the #ifdef section that has the only user, to avoid the harmless warning. Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Fixes: d08f50dd0afc ("rtc: rv3029: Add support of RV3049") Signed-off-by:
Alexandre Belloni <alexandre.belloni@free-electrons.com>
-
Thomas Koeller authored
The R2025SD chip, according to its data sheet, sets the /XST bit to zero if the oscillator stops. Hence the check for this condition was wrong. Signed-off-by:
Thomas Koeller <thomas.koeller@baslerweb.com> Signed-off-by:
-
Mylène Josserand authored
Add the alarm IRQ functionality. Signed-off-by:
Mylène Josserand <mylene.josserand@free-electrons.com> Signed-off-by:
-
Mylène Josserand authored
The bin2bcd function in set_time is uncorrect on weekdays as the bit mask should be done at the end of arithmetic operations. Signed-off-by:
-
Mylène Josserand authored
The RTC RV3029 handles different types of alarms : seconds, minutes, ... These alarms can be enabled or disabled individually using an AE_x bit which is the last bit (BIT(7)) on each alarm registers. To prepare the alarm IRQ support, the current code enables all the alarm types by setting each AE_x to 1. It also fixes others alarms issues : - month and weekday errors : it was performing -1 instead of +1. - wrong use of bit mask with bin2bcd Signed-off-by:
-
Mylène Josserand authored
Remove some checks from checkpatch such as spaces around arithmetic operations or prefer "unsigned int". Signed-off-by:
-
Mylène Josserand authored
Add support of Microcrystal RV3049 RTC (SPI) using regmap on the RV3029 (I2C) driver. Signed-off-by:
-
Mylène Josserand authored
To add support of rv3049, the current driver is converted to use regmap. Signed-off-by:
-
Mylène Josserand authored
To prepare the use of regmap to add the support of RV-3049, all the 'i2c' in functions's names are removed. Signed-off-by:
-
- 20 May, 2016 30 commits
-
-
Sudip Mukherjee authored
stmp3xxx_wdt_register() can fail as platform_device_alloc() or platform_device_add() can fail. But when it fails it failed silently. Lets print out an error message on failure so that user will atlest know that there was some error. Signed-off-by:
Sudip Mukherjee <sudip.mukherjee@codethink.co.uk> Signed-off-by:
-
Javier Martinez Canillas authored
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either built-in or as a module, use that macro instead of open coding the same. Signed-off-by:
Javier Martinez Canillas <javier@osg.samsung.com> Signed-off-by:
-
Qianyu Gong authored
The rtc->ops_lock would be accessed in ds3232_irq() without being initialized as rtc_device_register() is called too late. So move devm_rtc_device_register() just before registering irq handler to initialize rtc->ops_lock earlier. Signed-off-by:
Gong Qianyu <Qianyu.Gong@nxp.com> Reviewed-by:
Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by:
-
Stefan Agner authored
If enable_irq_wake fails, we should return that error code so that entering suspend fails. Otherwise we will get a WARNING along with the hint of a unbalanced wake disable: Unbalanced IRQ 37 wake disable Signed-off-by:
Stefan Agner <stefan@agner.ch> Signed-off-by:
-
Anurag Kumar Vulisha authored
We program RTC time using SET_TIME_WRITE register and read the RTC current time using CURRENT_TIME register. When we set the time by writing into SET_TIME_WRITE Register and immediately try to read the rtc time from CURRENT_TIME register, the previous old value is returned instead of the new loaded time. This is because RTC takes nearly 1 sec to update the new loaded value into the CURRENT_TIME register. This behaviour is expected in our RTC IP. This patch updates the driver to read the current time from SET_TIME_WRITE register instead of CURRENT_TIME when rtc time is requested within an 1sec period after setting the RTC time. Doing so will ensure the correct time is given to the user. Since there is a delay of 1sec in updating the CURRENT_TIME we are loading set time +1sec while programming the SET_TIME_WRITE register, doing this will give correct time without any delay when read from CURRENT_TIME. Signed-off-by:
Anurag Kumar Vulisha <anuragku@xilinx.com> Signed-off-by:
-
Geert Uytterhoeven authored
Fix typo in interrupt-names Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Acked-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Wolfram Sang authored
The RTC core handles it since 6610e089 (RTC: Rework RTC code to use timerqueue for events). So far, only the callbacks to the RTC core have been removed, but not the handlers. Do this now. Signed-off-by:
Wolfram Sang <w.sang@pengutronix.de> Signed-off-by:
-
Wolfram Sang authored
The RTC core handles it since 6610e089 (RTC: Rework RTC code to use timerqueue for events). Signed-off-by:
-
Stephen Boyd authored
This flag is a no-op now (see commit 47b0eeb3 "clk: Deprecate CLK_IS_ROOT", 2016-02-02) so remove it. Cc: Akinobu Mita <akinobu.mita@gmail.com> Cc: Michael Tatarinov <kukabu@gmail.com> Signed-off-by:
Stephen Boyd <sboyd@codeaurora.org> Signed-off-by:
-
Stephen Boyd authored
This flag is a no-op now (see commit 47b0eeb3 "clk: Deprecate CLK_IS_ROOT", 2016-02-02) so remove it. Cc: Heiko Stuebner <heiko@sntech.de> Signed-off-by:
-
Stephen Boyd authored
This flag is a no-op now (see commit 47b0eeb3 "clk: Deprecate CLK_IS_ROOT", 2016-02-02) so remove it. Cc: Heiko Schocher <hs@denx.de> Signed-off-by:
Heiko Schocher <hs@denx.de> Signed-off-by:
-
Anurag Kumar Vulisha authored
It is suggested to program CALIB_WRITE register with the calibration value before updating the SET_TIME_WRITE register, doing so will clear the Tick Counter and force the next second to be signaled exactly in 1 second. Signed-off-by:
-
Anurag Kumar Vulisha authored
In order to conserve battery energy, during the PS operation, it is expected that the supply for the battery-powered domain to be switched from the battery (VCC_PSBATT) to (VCC_PSAUX) and automatically be switched back to battery when VCC_PSAUX voltage drops below a limit, doing so prevents the logic within the battery-powered domain from functioning incorrectly. Signed-off-by:
-
Josh Poimboeuf authored
objtool reports the following warning: drivers/rtc/rtc-ds1685.o: warning: objtool: ds1685_rtc_poweroff() falls through to next function ds1685_rtc_work_queue() Similar to commit 361c6ed6 ("rtc: ds1685: actually spin forever in poweroff error path"), there's another unreachable() annotation which is actually reachable, which we missed the first time. Actually spin forever to be consistent with the comment and to make the unreachable() annotation guaranteed to be unreachable. Reported-by:
kbuild test robot <fengguang.wu@intel.com> Signed-off-by:
Josh Poimboeuf <jpoimboe@redhat.com> Signed-off-by:
-
Steve Twiss authored
This fix alters the ordering of the IRQ and device registrations in the RTC driver probe function. This change will apply to the RTC driver that supports both DA9052 and DA9053 PMICs. A problem could occur with the existing RTC driver if: A system is started from a cold boot using the PMIC RTC IRQ to initiate a power on operation. For instance, if an RTC alarm is used to start a platform from power off. The existing driver IRQ is requested before the device has been properly registered. i.e. ret = da9052_request_irq() comes before rtc->rtc = devm_rtc_device_register(); In this case, an interrupt exists before the device has been registered and the IRQ handler can be called immediately: this can happen be before the memory for rtc->rtc has been allocated. The IRQ handler da9052_rtc_irq() contains the function call: rtc_update_irq(rtc->rtc, 1, RTC_IRQF | RTC_AF); which in turn tries to access the unavailable rtc->rtc. The fix is to reorder the functions inside the RTC probe. The IRQ is requested after the RTC device resource has been registered so that da9052_request_irq() is the last thing to happen. Signed-off-by:
Steve Twiss <stwiss.opensource@diasemi.com> Signed-off-by:
-
Nicolas Boullis authored
If a previously-set alarm was disabled and then triggered, it may still be pending when a new alarm is configured. Then, if the alarm is enabled before the pending alarm is cleared, then an interrupt is immediately raised. Unfortunately, when the alarm is cleared and enabled during the same I²C block write, the chip (at least the DS1339 I have) considers that the alarm is enabled before it is cleared, and raises an interrupt. This patch ensures that the pending alarm is cleared before the alarm is enabled. Signed-off-by:
Nicolas Boullis <nboullis@debian.org> Signed-off-by:
-
Nicolas Boullis authored
The i2c_smbus_read_i2c_block_data function returns 0 on success, not the number of bytes written. Hence, when there are 32 bytes or less to send, the ds1307_native_smbus_write_block_data function returns 0 on success, while it returns the number of bytes when there are more than 32. The ds1307_write_block_data always returns the number of bytes on success. Signed-off-by:
-
Akinobu Mita authored
The valid range of day of week register for DS1302 is 1 to 7. But the set_time callback for rtc-ds1302 attempts to write the value of tm->tm_wday which is in the range 0 to 6. While the get_time callback correctly decodes the register. Signed-off-by:
-
Akinobu Mita authored
The set_time callback for rtc-ds1302 doesn't write clock registers because the error check for the return value from spi_write_then_read() is not correct. spi_write_then_read() which returns zero on success. Signed-off-by:
-
Mylène Josserand authored
Handle the Oscillator Failure (OF) bit on each read of date-time. If the OF is set, an error is returned (-EINVAL) instead of the date-time. The OF bit is cleared each time the date is set. Signed-off-by:
-
Mylène Josserand authored
To enable the wakealarm, the device must be able to wakeup. This is done by setting the device wakeup capability to true with 'device_init_wakeup' function. Signed-off-by:
-
Mylène Josserand authored
Previous 'commit c3b79770 ("Expire alarms after the time is set")' and 'commit 48e97667 ("remove disabled alarm functionality")' removed the alarm support because the alarm irq was not functional. Add the alarm IRQ functionality with newer functions than previous code. Tested with 'rtctest' and the alarm is functional. Signed-off-by:
-
Mylène Josserand authored
Replace the obsolete "simple_strtoul" function to "kstrtoul". Remove some checkpatch's errors, warnings and checks : - alignment with open parenthesis - spaces around '<' and '<<' - blank line after structure - quoted string split across lines Signed-off-by:
-
Mylène Josserand authored
Replace bit shifts by BIT macro. Signed-off-by:
-
Mylène Josserand authored
The driver used i2c_transfer methods to read and set date/time. The smbus methods should be used. This commit replaces i2c_transfer functions by i2c_smbus_XX_i2c_block_data for reading and setting the datetime. Signed-off-by:
-
Mylène Josserand authored
Remove the CONFIG_RTC_INTF_PROC and CONFIG_RTC_INTF_PROC_MODULE macro which is not necessary anymore. Signed-off-by:
-
Mylène Josserand authored
The driver used an old sysfs entry export. Update it to use the DEVICE_ATTR_XX macro and remove the unnecessary CONFIG_RTC_INTF_SYSFS macro. Signed-off-by:
-
Alexandre Belloni authored
Many drivers are defining a DRV_VERSION. This is often only used for MODULE_VERSION and sometimes to print an info message at probe time. This is kind of pointless as they are all versionned with the kernel anyway. Also the core will print a message when a new rtc is found. Signed-off-by: -
Colin Ian King authored
mr is written twice with the same value, remove one of the redundant assignments to mr. Signed-off-by:
Colin Ian King <colin.king@canonical.com> Signed-off-by:
-
Sergey Yanovich authored
DS1302 is an half-duplex SPI device. The driver respects this fact now. Pin configurations should be implemented using SPI subsystem. Signed-off-by:
Sergei Ianovich <ynvich@gmail.com> Acked-by:
-
- 15 May, 2016 1 commit
-
-
Linus Torvalds authored
-
