Noticed by Jun Sun.

Fix a couple of minor build errors caused by the recent system device
changes.

Ensure virt_addr_valid(x) works correctly for pointers.
Add comments indicating that drivers should not use virt_to_phys
and/or __pa to obtain an address for DMA.

This cset makes use of our AMBA device model, thereby allowing the
"KMI" PrimeCell driver to become ARM platform independent.

The ICS525 clock chip is used in several different parts of the
Integrator platform.  Rather than duplicate the code, separate it
out so everyone can use it.

into flint.arm.linux.org.uk:/usr/src/linux-bk-2.5/linux-2.5-rmk

I must not ignore compiler warnings.
I must not ignore compiler warnings.
I must not ignore compiler warnings.

Avoid the linear list walk of get_exec_dcookie() when we've switched to a task
using the same mm.

Use the IO-APIC NMI delivery when the local APIC performance counter delivery is
not available. By Zwane Mwaikambo.

Reduce the possibility of dazed-and-confuseds.

 - Fix 'badness in local_bh_enable' warning

   This involved moving dev_queue_xmit() calls
   outside of sections with spinlock held.

 - Fix 'fix old protocol handler' warning

   This includes accounting for shared skbs,
   setting protocol .data field to non-null,
   and adding per device synchronization to
   receive handler.

This has been tested in PPP and Cisco modes
with and with out the keepalives enabled
on a SMP machine.

This patch creates fs/Kconfig.binfmt and converts all architectures to
use it.  I took the opportunity to spruce up the a.out help text for
the new millennium.

request might traverse several export points which may
have different uid squashing.

From: "William A.(Andy) Adamson" <andros@citi.umich.edu>

From: "William A.(Andy) Adamson" <andros@citi.umich.edu>

Put all clients in a LRU list and use a "work_queue" to
expire old clients periodically.

From: "William A.(Andy) Adamson" <andros@citi.umich.edu>

When readdir is enumerating a directory and finds a mountpoint,
it needs to do a bit of extra work to find the filehandle to be
returned in the readdir reply.

It is even possible that finding the filehandle requires an up-call,
so the request might be dropped to be re-tried later.

From: Hirokazu Takahashi <taka@valinux.co.jp>

In svc_tcp_listen_data_ready we should be waiting for
TCP_LISTEN, not TCP_ESTABLISHED.  The later only worked
by accident.

Also, if a socket is closed as soon as we accept it, we
must shut it down straight away as we will never get a 'close'
event.

The most significant fix is cleaning up properly when
nfs service is stopped.

Also fix some refcounting problems and other little bits.

svc_pushback_unused_pages must be ready of the possibility that
no pages were allocated or will need to be pushed back.

From Adrian Bunk.

into home.transmeta.com:/home/torvalds/v2.5/linux

Here enclosed an update for the new IRQ and module_param APIs.
eata.h and u14-34f.h are no longer used and will be deleted.

into home.transmeta.com:/home/torvalds/v2.5/linux

The parisc ports may use both the lasi700 and sim710 versions of this driver
Unfortunately, one must be memory mapped, and one must be IO mapped, so
add code to the driver for this case

into kernel.bkbits.net:/home/davem/sparc-2.5

into kernel.bkbits.net:/home/davem/sparc-2.5

into home.transmeta.com:/home/torvalds/v2.5/linux

into home.transmeta.com:/home/torvalds/v2.5/linux

Some socket hardware appears to "bounce" when a card is inserted - we
seem to receive more than one SS_DETECT event.  Unfortunately, this
causes us to initialise, setup the socket, and create the necessary
devices multiple times.

Fix this by ignoring card insertion events when we already know that
there is a card in the socket.

while trying to access a disk drive via an FCP bridge we got an FCP_RSP IU
with the RSP_CODE field set to "FCP_CMND Fields Invalid". This happened
after sending a START_STOP command to the device. Reason for this was that
the FCP_CMND IU incorrectly had the RDDATA field set to one, because of a
bug in sd_spinup_disk(). There the data direction for START_STOP is set
to SCSI_DATA_READ instead of SCSI_DATA_NONE.
Please apply the patch below.

Thanks,
Heiko