RSS had previously been disabled when DCB was enabled because
DCB was single queued per traffic class. Now that DCB implements
multiple Tx/Rx rings per traffic class enable RSS.

Here RSS hashes across the queues in the traffic class.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain.@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds the ndo_tc_setup to ixgbe. By default we set
the device to use strict priority.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain.@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This enables multiple {Tx|Rx} rings per traffic class while in DCB
mode. In order to get this working as expected the tc_to_tx net
device mapping is configured as well as the prio_tc_map.

skb priorities are mapped across a range of queue pairs to get
a distribution per traffic class. The maximum number of
queue pairs used while in DCB mode is capped at 64. The hardware
max is actually 128 queues but 64 is sufficient for now and
allocating more seemed a bit excessive. It is easy enough to
increase the cap later if need be.

To get the 802.1Q priority tags inserted correctly ixgbe was
previously using the skb queue_mapping field to directly set
the 802.1Q priority. This no longer works because we have removed
the 1:1 mapping between queues and traffic class. Each ring
is aligned with an 802.1Qaz traffic class so here we add an
extra field to the ring struct to identify the 802.1Q traffic
class. This uses an extra byte of the ixgbe_ring struct
fortunately there was a 2byte hole,

struct ixgbe_ring {
        void *                     desc;                 /*     0     8 */
        struct device *            dev;                  /*     8     8 */
        struct net_device *        netdev;               /*    16     8 */
        union {
                struct ixgbe_tx_buffer * tx_buffer_info; /*           8 */
                struct ixgbe_rx_buffer * rx_buffer_info; /*           8 */
        };                                               /*    24     8 */
        long unsigned int          state;                /*    32     8 */
        u8                         atr_sample_rate;      /*    40     1 */
        u8                         atr_count;            /*    41     1 */
        u16                        count;                /*    42     2 */
        u16                        rx_buf_len;           /*    44     2 */
        u16                        next_to_use;          /*    46     2 */
        u16                        next_to_clean;        /*    48     2 */
        u8                         queue_index;          /*    50     1 */
        u8                         reg_idx;              /*    51     1 */
        u16                        work_limit;           /*    52     2 */

        /* XXX 2 bytes hole, try to pack */

        u8 *                       tail;                 /*    56     8 */
        /* --- cacheline 1 boundary (64 bytes) --- */

Now we can set the VLAN priority directly and it will be
correct. User space can indicate the 802.1Qaz priority
using the SO_PRIORITY setsocket() option and QOS layer will
steer the skb to the correct rings. Additionally using
the multiq qdisc with a queue_mapping action works as
well.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Remove ixgbe_fcoe_getapp() and use the generic kernel
routine instead. Also add application priority to the
kernel maintained list on setapp so applications and
stacks can query the value.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Implement ieee_setapp dcbnl ops in ixgbe. This is required
to setup FCoE which requires dedicated resources. If the
app data is not for FCoE then no action is taken in ixgbe
except to add it to the dcb_app_list.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This implements dcbnl get and set capabilities ops. The
devices supported by ixgbe can be configured to run in
IEEE or CEE modes but not both.

With the DCBX set capabilities bit we add an explicit
signal that must be used to toggle between these modes.
This patch adds logic to fail the CEE command set_hw_all()
which programs the device with a CEE configuration if
the CEE caps bit is not set. Similarly, IEEE set
commands will fail if the IEEE caps bit is not set. We
allow most CEE config set commands to occur because they
do not touch the hardware until set_hw_all() is called.

The one exception to the above is the {set|get}app routines.
These must always be protected by caps bits to ensure
side effects do not corrupt the current configured mode.

By requiring the caps bit to be set correctly we can
maintain a consistent configuration in the hardware
for CEE or IEEE modes and prevent partial hardware
configurations that may occur if user space does
not send a complete IEEE or CEE configurations.

It is expected that user space will signal a DCBX mode
before programming device.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch updates igb version to 3.0.6.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch add DMA Coalescing which is a power-saving feature that
coalesces DMA writes in order to stay in a low-power state as much
as possible.  Feature is disabled by default.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds functions and functions pointers to accommodate
differences between NVM interfaces and options for i350 devices,
82580 devices and the rest.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds the EEE feature for i350 devices, enabled by default.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Change the driver string to match the PF driver string format.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The kernel version string is off by a major version number since
new silicon was just introduced and also uses the wrong format for
the version postfix.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The driver doesn't support Wake-on-ARP, so don't advertise through ethtool
that it does.

Cleanup some coding style issues in the same functions.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

If/when an OEM enables MACsec in the 82579 EEPROM, disable jumbo frames
support in the driver due to an interoperability issue in hardware that
prevents jumbo packets from being transmitted or received.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

When PHY reset is intentionally blocked on 82577/8/9, do not toggle the
LANPHYPC value bit (essentially performing a hard power reset of the
device) otherwise the PHY can be put into an unknown state.

Cleanup whitespace in the same function.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The link can be unexpectedly dropped when the timer for entering EEE low-
power-idle quiet state expires too soon.  The timer needs to be extended
from 196usec to 200usec after every LCD (PHY) reset to prevent this from
happening.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

With some PHYs supported by this driver, link establishment can take a
little longer when connected to certain switches.  Extend the timeout to
reduce the number of false diagnostic failures, and cleanup a code style
issue in the same function.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Based on a report and patch originally submitted by Prasanna Panchamukhi.

Use dev_kfree_skb_irq() in e1000_clean_jumbo_rx_irq() since this latter
function is called only in interrupt context.  This avoids "Warning:
kfree_skb on hard IRQ" messages.

Cc: "Prasanna S. Panchamukhi" <prasanna.panchamukhi@riverbed.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Removed Tx hang detection mechanism from ixgbevf.
This mechanism has no affect and can cause false alarm messages in some
cases. Especially when VF Tx rate limit is turned on.

The same mechanism was removed recently from igbvf.
Signed-off-by: Lior Levy <lior.levy@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Add proper documentation for previously added net_device_ops ops for FCoE.
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Based on a patch from Jesse Gross <jesse@nicira.com>

This switches the ixgb driver to use the new VLAN interfaces.
In doing this, it completes the work begun in
ae54496f allowing the use of
hardware VLAN insertion without having a VLAN group configured.

CC: Jesse Gross <jesse@nicira.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Completely unused.
Signed-off-by: David S. Miller <davem@davemloft.net>

fl->oif will always be zero on the input path, so there is no reason
to test for that.
Signed-off-by: David S. Miller <davem@davemloft.net>

All callers are under rcu_read_lock() protection already.

Rename to ip_check_mc_rcu() to make it even more clear.
Signed-off-by: David S. Miller <davem@davemloft.net>

Conflicts:
	drivers/net/bnx2x/bnx2x_cmn.c

Add necessary alias to autoload ip6ip6 tunnel module.
Signed-off-by: Stephen Hemminger <shemminger@vyatta.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When configs BRIDGE=y and IPV6=m, this build error occurs:

br_multicast.c:(.text+0xa3341): undefined reference to `ipv6_dev_get_saddr'

BRIDGE_IGMP_SNOOPING is boolean; if it were tristate, then adding
	depends on IPV6 || IPV6=n
to BRIDGE_IGMP_SNOOPING would be a good fix.  As it is currently,
making BRIDGE depend on the IPV6 config works.
Reported-by: Patrick Schaaf <netdev@bof.de>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

* 'media_fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-2.6:
  [media] mantis_pci: remove asm/pgtable.h include
  [media] tda829x: fix regression in probe functions
  [media] mceusb: don't claim multifunction device non-IR parts
  [media] nuvoton-cir: fix wake from suspend
  [media] cx18: Add support for Hauppauge HVR-1600 models with s5h1411
  [media] ivtv: Fix corrective action taken upon DMA ERR interrupt to avoid hang
  [media] cx25840: fix probing of cx2583x chips
  [media] cx23885: Remove unused 'err:' labels to quiet compiler warning
  [media] cx23885: Revert "Check for slave nack on all transactions"
  [media] DiB7000M: add pid filtering
  [media] Fix sysfs rc protocol lookup for rc-5-sz
  [media] au0828: fix VBI handling when in V4L2 streaming mode
  [media] ir-raw: Properly initialize the IR event (BZ#27202)
  [media] s2255drv: firmware re-loading changes
  [media] Fix double free of video_device in mem2mem_testdev
  [media] DM04/QQBOX memcpy to const char fix

This patch fixes an issue in OpenIPMI module where sometimes an ABORT command
is sent after sending an IPMI request to BMC causing the IPMI request to fail.
Signed-off-by: YiCheng Doe <yicheng.doe@hp.com>
Signed-off-by: Corey Minyard <cminyard@mvista.com>
Acked-by: Tom Mingarelli <thomas.mingarelli@hp.com>
Tested-by: Andy Cress <andy.cress@us.kontron.com>
Tested-by: Mika Lansirine <Mika.Lansirinne@stonesoft.com>
Tested-by: Brian De Wolf <bldewolf@csupomona.edu>
Cc: Jean Michel Audet <Jean-Michel.Audet@ca.Kontron.com>
Cc: Jozef Sudelsky <jozef.sudolsky@elbiahosting.sk>
Acked-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs-2.6:
  fs/dcache: allow d_obtain_alias() to return unhashed dentries
  Check for immutable/append flag in fallocate path
  sysctl: the include of rcupdate.h is only needed in the kernel
  fat: fix d_revalidate oopsen on NFS exports
  jfs: fix d_revalidate oopsen on NFS exports
  ocfs2: fix d_revalidate oopsen on NFS exports
  gfs2: fix d_revalidate oopsen on NFS exports
  fuse: fix d_revalidate oopsen on NFS exports
  ceph: fix d_revalidate oopsen on NFS exports
  reiserfs xattr ->d_revalidate() shouldn't care about RCU
  /proc/self is never going to be invalidated...

Merge branch 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'x86-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  x86, UV: Initialize the broadcast assist unit base destination node id properly
  x86, numa: Fix numa_emulation code with memory-less node0
  x86, build: Make sure mkpiggy fails on read error

Merge branch 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip

* 'sched-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  sched: Fix sched rt group scheduling when hierachy is enabled

* 'perf/urgent' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/linux-2.6-tip:
  perf symbols: Avoid resolving [kernel.kallsyms] to real path for buildid cache
  perf symbols: Fix vmlinux path when not using --symfs

This reverts commit 951f3512

    drm/i915: Do not handle backlight combination mode specially

since this commit introduced other regressions due to untouched LBPC
register, e.g. the backlight dimmed after resume.

In addition to the revert, this patch includes a fix for the original
issue (weird backlight levels) by removing the wrong bit shift for
computing the current backlight level.
Also, including typo fixes (lpbc -> lbpc).

Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=34524Acked-by: Indan Zupancic <indan@nul.nu>
Reviewed-by: Keith Packard <keithp@keithp.com>
Reviewed-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Cc: <stable@kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Without this patch, inodes are not promptly freed on last close of an
unlinked file by an nfs client:

	client$ mount -tnfs4 server:/export/ /mnt/
	client$ tail -f /mnt/FOO
	...
	server$ df -i /export
	server$ rm /export/FOO
	(^C the tail -f)
	server$ df -i /export
	server$ echo 2 >/proc/sys/vm/drop_caches
	server$ df -i /export

the df's will show that the inode is not freed on the filesystem until
the last step, when it could have been freed after killing the client's
tail -f. On-disk data won't be deallocated either, leading to possible
spurious ENOSPC.

This occurs because when the client does the close, it arrives in a
compound with a putfh and a close, processed like:

	- putfh: look up the filehandle.  The only alias found for the
	  inode will be DCACHE_UNHASHED alias referenced by the filp
	  this, so it creates a new DCACHE_DISCONECTED dentry and
	  returns that instead.
	- close: closes the existing filp, which is destroyed
	  immediately by dput() since it's DCACHE_UNHASHED.
	- end of the compound: release the reference
	  to the current filehandle, and dput() the new
	  DCACHE_DISCONECTED dentry, which gets put on the
	  unused list instead of being destroyed immediately.

Nick Piggin suggested fixing this by allowing d_obtain_alias to return
the unhashed dentry that is referenced by the filp, instead of making it
create a new dentry.

Leave __d_find_alias() alone to avoid changing behavior of other
callers.

Also nfsd doesn't need all the checks of __d_find_alias(); any dentry,
hashed or unhashed, disconnected or not, should work.
Signed-off-by: J. Bruce Fields <bfields@redhat.com>
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>

The 5750 ASIC rev was never released as a PCI device.  It only exists as
a PCIe device.  This patch removes the code that supports the former
configuration.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch moves the function that initializes the link configuration
closer to the place where the rest of the phy code is initialized.
Signed-off-by: Matt Carlson <mcarlson@broadcom.com>
Reviewed-by: Michael Chan <mchan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>