- 29 May, 2020 1 commit
-
-
wuxu.wu authored
dw_spi_irq() and dw_spi_transfer_one concurrent calls. I find a panic in dw_writer(): txw = *(u8 *)(dws->tx), when dw->tx==null, dw->len==4, and dw->tx_end==1. When tpm driver's message overtime dw_spi_irq() and dw_spi_transfer_one may concurrent visit dw_spi, so I think dw_spi structure lack of protection. Otherwise dw_spi_transfer_one set dw rx/tx buffer and then open irq, store dw rx/tx instructions and other cores handle irq load dw rx/tx instructions may out of order. [ 1025.321302] Call trace: ... [ 1025.321319] __crash_kexec+0x98/0x148 [ 1025.321323] panic+0x17c/0x314 [ 1025.321329] die+0x29c/0x2e8 [ 1025.321334] die_kernel_fault+0x68/0x78 [ 1025.321337] __do_kernel_fault+0x90/0xb0 [ 1025.321346] do_page_fault+0x88/0x500 [ 1025.321347] do_translation_fault+0xa8/0xb8 [ 1025.321349] do_mem_abort+0x68/0x118 [ 1025.321351] el1_da+0x20/0x8c [ 1025.321362] dw_writer+0xc8/0xd0 [ 1025.321364] interrupt_transfer+0x60/0x110 [ 1025.321365] dw_spi_irq+0x48/0x70 ... Signed-off-by:
wuxu.wu <wuxu.wu@huawei.com> Link: https://lore.kernel.org/r/1577849981-31489-1-git-send-email-wuxu.wu@huawei.comSigned-off-by:
Mark Brown <broonie@kernel.org> CVE-2020-12769 (cherry picked from commit 19b61392) [ ben_r: 1 line adjustment to patch ] Signed-off-by:
Benjamin M Romer <benjamin.romer@canonical.com> Acked-by:
Stefan Bader <stefan.bader@canonical.com> Acked-by:
Thadeu Lima de Souza Cascardo <cascardo@canonical.com> Signed-off-by:
Khalid Elmously <khalid.elmously@canonical.com>
-
- 28 May, 2020 1 commit
-
-
Wen-chien Jesse Sung authored
BugLink: https://launchpad.net/bugs/1881124 I2C bus on Dell Edge Gateway stops working after commit Revert "ACPI / LPSS: allow to use specific PM domain during ->probe()" with error messages like: [ 13.812210] i2c_designware 80860F41:01: Unknown Synopsys component type: 0x00000000 [ 13.855837] i2c_designware 80860F41:01: timeout in enabling adapter [ 14.856276] i2c_designware 80860F41:01: controller timed out [ 14.856288] i2c_designware 80860F41:01: Unknown Synopsys component type: 0x00000000 Revert the commit for now until we figure out what is really causing the problem. Signed-off-by:
Wen-chien Jesse Sung <jesse.sung@canonical.com> Acked-by:
Kleber Sacilotto de Souza <kleber.souza@canonical.com> Acked-by:
Andrea Righi <andrea.righi@canonical.com> Signed-off-by:
-
- 15 May, 2020 3 commits
-
-
Kleber Sacilotto de Souza authored
Signed-off-by: -
Kleber Sacilotto de Souza authored
BugLink: https://bugs.launchpad.net/bugs/1878873 Properties: no-test-build Signed-off-by:
-
Kleber Sacilotto de Souza authored
Ignore: yes Signed-off-by:
-
- 14 May, 2020 35 commits
-
-
Greg Kroah-Hartman authored
BugLink: https://bugs.launchpad.net/bugs/1878232Signed-off-by:
Ian May <ian.may@canonical.com> Signed-off-by:
-
Thomas Pedersen authored
BugLink: https://bugs.launchpad.net/bugs/1878232 commit 30b2f0be upstream. commit 08a5bdde ("mac80211: consider QoS Null frames for STA_NULLFUNC_ACKED") Fixed a bug where we failed to take into account a nullfunc frame can be either non-QoS or QoS. It turns out there is at least one more bug in ieee80211_sta_tx_notify(), introduced in commit 7b6ddeaf ("mac80211: use QoS NDP for AP probing"), where we forgot to check for the QoS variant and so assumed the QoS nullfunc frame never went out Fix this by adding a helper ieee80211_is_any_nullfunc() which consolidates the check for non-QoS and QoS nullfunc frames. Replace existing compound conditionals and add a couple more missing checks for QoS variant. Signed-off-by:
Thomas Pedersen <thomas@adapt-ip.com> Link: https://lore.kernel.org/r/20200114055940.18502-3-thomas@adapt-ip.comSigned-off-by:
Johannes Berg <johannes.berg@intel.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
-
Takashi Iwai authored
BugLink: https://bugs.launchpad.net/bugs/1878232 commit 977dfef4 upstream. The commit 3c6fd1f0 ("ALSA: hda: Add driver blacklist") added a new blacklist for the devices that are known to have empty codecs, and one of the entries was ASUS ROG Zenith II (PCI SSID 1043:874f). However, it turned out that the very same PCI SSID is used for the previous model that does have the valid HD-audio codecs and the change broke the sound on it. Since the empty codec problem appear on the certain AMD platform (PCI ID 1022:1487), this patch changes the blacklist matching to both PCI ID and SSID using pci_match_id(). Also, the entry that was removed by the previous fix for ASUS ROG Zenigh II is re-added. Link: https://lore.kernel.org/r/20200424061222.19792-1-tiwai@suse.deSigned-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
-
Jere Leppänen authored
BugLink: https://bugs.launchpad.net/bugs/1878232 commit 12dfd78e upstream. When starting shutdown in sctp_sf_do_dupcook_a(), get the value for SHUTDOWN Cumulative TSN Ack from the new association, which is reconstructed from the cookie, instead of the old association, which the peer doesn't have anymore. Otherwise the SHUTDOWN is either ignored or replied to with an ABORT by the peer because CTSN Ack doesn't match the peer's Initial TSN. Fixes: bdf6fa52 ("sctp: handle association restarts when the socket is closed.") Signed-off-by:
Jere Leppänen <jere.leppanen@nokia.com> Acked-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net> Signed-off-by:
-
Herbert Xu authored
BugLink: https://bugs.launchpad.net/bugs/1878232 commit 260916df upstream. When we postpone a broadcast packet we save the source port in the skb if it is local. However, the source port can disappear before we get a chance to process the packet. This patch fixes this by holding a ref count on the netdev. It also delays the skb->cb modification until after we allocate the new skb as you should not modify shared skbs. Fixes: 412ca155 ("macvlan: Move broadcasts into a work queue") Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Florian Fainelli authored
BugLink: https://bugs.launchpad.net/bugs/1878232 commit c823abac upstream. When we unload the ep93xx_eth, whether we have opened the network interface or not, we will either hit a kernel paging request error, or a simple NULL pointer de-reference because: - if ep93xx_open has been called, we have created a valid DMA mapping for ep->descs, when we call ep93xx_stop, we also call ep93xx_free_buffers, ep->descs now has a stale value - if ep93xx_open has not been called, we have a NULL pointer for ep->descs, so performing any operation against that address just won't work Fix this by adding a NULL pointer check for ep->descs which means that ep93xx_free_buffers() was able to successfully tear down the descriptors and free the DMA cookie as well. Fixes: 1d22e05d ("[PATCH] Cirrus Logic ep93xx ethernet driver") Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Shmulik Ladkani authored
BugLink: https://bugs.launchpad.net/bugs/1878232 commit 636c2628 upstream. In 93515d53 "net: move vlan pop/push functions into common code" skb_vlan_pop was moved from its private location in openvswitch to skbuff common code. In case skb has non hw-accel vlan tag, the original 'pop_vlan()' assured that skb->len is sufficient (if skb->len < VLAN_ETH_HLEN then pop was considered a no-op). This validation was moved as is into the new common 'skb_vlan_pop'. Alas, in its original location (openvswitch), there was a guarantee that 'data' points to the mac_header, therefore the 'skb->len < VLAN_ETH_HLEN' condition made sense. However there's no such guarantee in the generic 'skb_vlan_pop'. For short packets received in rx path going through 'skb_vlan_pop', this causes 'skb_vlan_pop' to fail pop-ing a valid vlan hdr (in the non hw-accel case) or to fail moving next tag into hw-accel tag. Remove the 'skb->len < VLAN_ETH_HLEN' condition entirely: It is superfluous since inner '__skb_vlan_pop' already verifies there are VLAN_ETH_HLEN writable bytes at the mac_header. Note this presents a slight change to skb_vlan_pop() users: In case total length is smaller than VLAN_ETH_HLEN, skb_vlan_pop() now returns an error, as opposed to previous "no-op" behavior. Existing callers (e.g. tc act vlan, ovs) usually drop the packet if 'skb_vlan_pop' fails. Fixes: 93515d53 ("net: move vlan pop/push functions into common code") Signed-off-by:
Shmulik Ladkani <shmulik.ladkani@gmail.com> Cc: Pravin Shelar <pshelar@ovn.org> Reviewed-by:
Pravin B Shelar <pshelar@ovn.org> Signed-off-by:
-
Ivan Vecera authored
BugLink: https://bugs.launchpad.net/bugs/1878232 commit 2835d2d9 upstream. Commit ba5ca784 "bna: check for dma mapping errors" added besides other things a statistic that counts number of DMA buffer mapping failures per each Rx queue. This counter is not included in ethtool stats output. Fixes: ba5ca784 "bna: check for dma mapping errors" Signed-off-by:
Ivan Vecera <ivecera@redhat.com> Signed-off-by:
-
Toshiaki Makita authored
BugLink: https://bugs.launchpad.net/bugs/1878232 commit 7bb90c37 upstream. Adding fdb entries pointing to the bridge device uses fdb_insert(), which lacks various checks and does not respect added_by_user flag. As a result, some inconsistent behavior can happen: * Adding temporary entries succeeds but results in permanent entries. * Same goes for "dynamic" and "use". * Changing mac address of the bridge device causes deletion of user-added entries. * Replacing existing entries looks successful from userspace but actually not, regardless of NLM_F_EXCL flag. Use the same logic as other entries and fix them. Fixes: 3741873b ("bridge: allow adding of fdb entries pointing to the bridge device") Signed-off-by:
Toshiaki Makita <makita.toshiaki@lab.ntt.co.jp> Acked-by:
Roopa Prabhu <roopa@cumulusnetworks.com> Signed-off-by:
-
Arend Van Spriel authored
BugLink: https://bugs.launchpad.net/bugs/1878232 commit 82bc9ab6 upstream. When the host-interface bus has hard time handling transmit packets it informs higher layer about this and it would stop the netdev queue when needed. However, since commit 9cd18359 ("brcmfmac: Make FWS queueing configurable.") this was broken. With this patch the behaviour is restored. Cc: stable@vger.kernel.org # v4.5, v4.6, v4.7 Fixes: 9cd18359 ("brcmfmac: Make FWS queueing configurable.") Tested-by:
Per Förlin <per.forlin@gmail.com> Reviewed-by:
Hante Meuleman <hante.meuleman@broadcom.com> Reviewed-by:
Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Reviewed-by:
Franky Lin <franky.lin@broadcom.com> Signed-off-by:
Arend van Spriel <arend.vanspriel@broadcom.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Signed-off-by:
-
Jaap Jan Meijer authored
BugLink: https://bugs.launchpad.net/bugs/1878232 commit 94abd778 upstream. If brcmf_cfg80211_get_station fails to determine the RSSI from the per-chain values get the value individually as a fallback. Fixes: 1f0dc59a ("brcmfmac: rework .get_station() callback") Signed-off-by:
Jaap Jan Meijer <jjmeijer88@gmail.com> Acked-by:
-
Laxman Dewangan authored
BugLink: https://bugs.launchpad.net/bugs/1878232 commit b22ef2a0 upstream. The pincontrol registers of Tegra chips has multiple filed per registers. There is two type of registers mux and drive. All configurations belongs to one of these registers. If any configurations are supported then <config>_bit is set to bit position of these registers otherwise -1 to not support it. The member is defined as s32 <config>_bit:6; So if config is not supported ifor given SoC then it is set to -1 in soc pinmmux table. In common driver code, to find out that given config is supported or not, it is checked as: s8 bit = <config>_bit; if (bit > 31) { /* Not supported config */ } But in this case, bit is s8 and hence for non supporting it is -1. Correct the check as: if (bit < 0) { /* Not supported config */ } Fixes: e4c02dce ("pinctrl: tegra: use signed bitfields for optional fields") Signed-off-by:
Laxman Dewangan <ldewangan@nvidia.com> Acked-by:
Stephen Warren <swarren@nvidia.com> Signed-off-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
-
Mans Rullgard authored
BugLink: https://bugs.launchpad.net/bugs/1878232 commit 55e610cd upstream. This lock is already taken in ata_scsi_queuecmd() a few levels up the call stack so attempting to take it here is an error. Moreover, it is pointless in the first place since it only protects a single, atomic assignment. Enabling lock debugging gives the following output: ============================================= [ INFO: possible recursive locking detected ] 4.4.0-rc5+ #189 Not tainted --------------------------------------------- kworker/u2:3/37 is trying to acquire lock: (&(&host->lock)->rlock){-.-...}, at: [<90283294>] sata_dwc_exec_command_by_tag.constprop.14+0x44/0x8c but task is already holding lock: (&(&host->lock)->rlock){-.-...}, at: [<902761ac>] ata_scsi_queuecmd+0x2c/0x330 other info that might help us debug this: Possible unsafe locking scenario: CPU0 ---- lock(&(&host->lock)->rlock); lock(&(&host->lock)->rlock); *** DEADLOCK *** May be due to missing lock nesting notation 4 locks held by kworker/u2:3/37: #0: ("events_unbound"){.+.+.+}, at: [<9003a0a4>] process_one_work+0x12c/0x430 #1: ((&entry->work)){+.+.+.}, at: [<9003a0a4>] process_one_work+0x12c/0x430 #2: (&bdev->bd_mutex){+.+.+.}, at: [<9011fd54>] __blkdev_get+0x50/0x380 #3: (&(&host->lock)->rlock){-.-...}, at: [<902761ac>] ata_scsi_queuecmd+0x2c/0x330 stack backtrace: CPU: 0 PID: 37 Comm: kworker/u2:3 Not tainted 4.4.0-rc5+ #189 Workqueue: events_unbound async_run_entry_fn Stack : 90b38e30 00000021 00000003 9b2a6040 00000000 9005f3f0 904fc8dc 00000025 906b96e4 00000000 90528648 9b3336c4 904fc8dc 9009bf18 00000002 00000004 00000000 00000000 9b3336c4 9b3336e4 904fc8dc 9003d074 00000000 90500000 9005e738 00000000 00000000 00000000 00000000 00000000 00000000 00000000 6e657665 755f7374 756f626e 0000646e 00000000 00000000 9b00ca00 9b025000 ... Call Trace: [<90009d6c>] show_stack+0x88/0xa4 [<90057744>] __lock_acquire+0x1ce8/0x2154 [<900583e4>] lock_acquire+0x64/0x8c [<9045ff10>] _raw_spin_lock_irqsave+0x54/0x78 [<90283294>] sata_dwc_exec_command_by_tag.constprop.14+0x44/0x8c [<90283484>] sata_dwc_qc_issue+0x1a8/0x24c [<9026b39c>] ata_qc_issue+0x1f0/0x410 [<90273c6c>] ata_scsi_translate+0xb4/0x200 [<90276234>] ata_scsi_queuecmd+0xb4/0x330 [<9025800c>] scsi_dispatch_cmd+0xd0/0x128 [<90259934>] scsi_request_fn+0x58c/0x638 [<901a3e50>] __blk_run_queue+0x40/0x5c [<901a83d4>] blk_queue_bio+0x27c/0x28c [<901a5914>] generic_make_request+0xf0/0x188 [<901a5a54>] submit_bio+0xa8/0x194 [<9011adcc>] submit_bh_wbc.isra.23+0x15c/0x17c [<9011c908>] block_read_full_page+0x3e4/0x428 [<9009e2e0>] do_read_cache_page+0xac/0x210 [<9009fd90>] read_cache_page+0x18/0x24 [<901bbd18>] read_dev_sector+0x38/0xb0 [<901bd174>] msdos_partition+0xb4/0x5c0 [<901bcb8c>] check_partition+0x140/0x274 [<901bba60>] rescan_partitions+0xa0/0x2b0 [<9011ff68>] __blkdev_get+0x264/0x380 [<901201ac>] blkdev_get+0x128/0x36c [<901b9378>] add_disk+0x3c0/0x4bc [<90268268>] sd_probe_async+0x100/0x224 [<90043a44>] async_run_entry_fn+0x50/0x124 [<9003a11c>] process_one_work+0x1a4/0x430 [<9003a4f4>] worker_thread+0x14c/0x4fc [<900408f4>] kthread+0xd0/0xe8 [<90004338>] ret_from_kernel_thread+0x14/0x1c Fixes: 62936009 ("[libata] Add 460EX on-chip SATA driver, sata_dwc_460ex") Tested-by:
Christian Lamparter <chunkeey@googlemail.com> Signed-off-by:
Mans Rullgard <mans@mansr.com> Signed-off-by:
Tejun Heo <tj@kernel.org> Signed-off-by:
-
Neil Armstrong authored
BugLink: https://bugs.launchpad.net/bugs/1878232 commit 210990b0 upstream. When the DaVinci emac driver is removed and re-probed, the actual pdev->dev.platform_data is populated with an unwanted valid pointer saved by the previous davinci_emac_of_get_pdata() call, causing a kernel crash when calling priv->int_disable() in emac_int_disable(). Unable to handle kernel paging request at virtual address c8622a80 ... [<c0426fb4>] (emac_int_disable) from [<c0427700>] (emac_dev_open+0x290/0x5f8) [<c0427700>] (emac_dev_open) from [<c04c00ec>] (__dev_open+0xb8/0x120) [<c04c00ec>] (__dev_open) from [<c04c0370>] (__dev_change_flags+0x88/0x14c) [<c04c0370>] (__dev_change_flags) from [<c04c044c>] (dev_change_flags+0x18/0x48) [<c04c044c>] (dev_change_flags) from [<c052bafc>] (devinet_ioctl+0x6b4/0x7ac) [<c052bafc>] (devinet_ioctl) from [<c04a1428>] (sock_ioctl+0x1d8/0x2c0) [<c04a1428>] (sock_ioctl) from [<c014f054>] (do_vfs_ioctl+0x41c/0x600) [<c014f054>] (do_vfs_ioctl) from [<c014f2a4>] (SyS_ioctl+0x6c/0x7c) [<c014f2a4>] (SyS_ioctl) from [<c000ff60>] (ret_fast_syscall+0x0/0x1c) Fixes: 42f59967 ("net: ethernet: davinci_emac: add OF support") Cc: Brian Hutchinson <b.hutchman@gmail.com> Signed-off-by:
Neil Armstrong <narmstrong@baylibre.com> Signed-off-by:
-
Aneesh Kumar K.V authored
BugLink: https://bugs.launchpad.net/bugs/1878232 commit 3b1dbfa1 upstream. The current code will set _PAGE_USER to the access flags for any fault address, because the ~ operation will be true for all address we take a fault on. But setting _PAGE_USER also means that the fault will be handled only if the page table have _PAGE_USER set. Hence there is no security hole with the current code. Now if it is an user space access, then the change in this patch really don't have an impact because we have (!ctx->kernel) set true and we take the if condition true. Now kernel context created fault on an address in the kernel range will result in a fault loop because we will not insert the hash pte due to access and pte permission mismatch. This patch fix the above issue. Fixes: f204e0b8 ("cxl: Driver code for powernv PCIe based cards for userspace access") Reviewed-by:
Andrew Donnellan <andrew.donnellan@au1.ibm.com> Acked-by:
Ian Munsie <imunsie@au1.ibm.com> Signed-off-by:
Aneesh Kumar K.V <aneesh.kumar@linux.vnet.ibm.com> Signed-off-by:
Michael Ellerman <mpe@ellerman.id.au> Signed-off-by:
-
Sergei Shtylyov authored
BugLink: https://bugs.launchpad.net/bugs/1878232 commit d57019d1 upstream. The driver of course "knows" that the chip's reset signal is active low, so it drives the GPIO to 0 to reset the PHY and to 1 otherwise; however all this will only work iff the GPIO is specified as active-high in the device tree! I think both the driver and the device trees (if there are any -- I was unable to find them) need to be fixed in this case... Fixes: 13a56b44 ("net: phy: at803x: Add support for hardware reset") Signed-off-by:
Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Acked-by:
Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by:
-
Vivien Didelot authored
BugLink: https://bugs.launchpad.net/bugs/1878232 commit be1faa92 upstream. Currently the port based VLAN maps should be configured to allow every port to egress frames on all other ports, except themselves. The debugfs interface shows that they are misconfigured. For instance, a 7-port switch has the following content in the related register 0x06: GLOBAL GLOBAL2 SERDES 0 1 2 3 4 5 6 ... 6: 1fa4 1f0f 4 7f 7e 7d 7c 7b 7a 79 ... This means that port 3 is allowed to talk to port 2-6, but cannot talk to ports 0 and 1. With this fix, port 3 can correctly talk to all ports except 3 itself: GLOBAL GLOBAL2 SERDES 0 1 2 3 4 5 6 ... 6: 1fa4 1f0f 4 7e 7d 7b 77 6f 5f 3f ... Fixes: ede8098d ("net: dsa: mv88e6xxx: bridges do not need an FID") Reported-by:
Kevin Smith <kevin.smith@elecsyscorp.com> Signed-off-by:
Vivien Didelot <vivien.didelot@savoirfairelinux.com> Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Tested-by:
-
Charles Keepax authored
BugLink: https://bugs.launchpad.net/bugs/1878232 commit 6333ef46 upstream. As we now free the constraints in regulator_dev_release we will still call free on the constraints pointer even if we went down an error path in regulator_register, because it is only allocated after the device_register. As such we no longer need to free rdev->constraints on the error paths, so this patch removes said frees. Fixes: 29f5f486 ("regulator: core: Move more deallocation into class unregister") Signed-off-by:
Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by:
-
Nicolas Schichan authored
BugLink: https://bugs.launchpad.net/bugs/1878232 commit 3b89624a upstream. The code in txq_put_data() would use txq->tx_curr_desc to index the tso_hdrs/tso_hdrs_dma buffers, for less than 8 bytes unaligned fragments, which is already moved to the next descriptor at the beginning of the function. If that fragment was the last of the the skb, the next skb would use that same space to place the ip headers, overwritting that small fragment data. Fixes: 91986fd3 (net: mv643xx_eth: Ensure proper data alignment in TSO TX path) Signed-off-by:
Nicolas Schichan <nschichan@freebox.fr> Reviewed-by:
Philipp Kirchhofer <philipp@familie-kirchhofer.de> Signed-off-by:
-
Florian Fainelli authored
BugLink: https://bugs.launchpad.net/bugs/1878232 commit 386512d1 upstream. In case any operation fails before we can successfully go the point where we would register a MDIO bus, we would be going to an error label which involves unregistering then freeing this yet to be created MDIO bus. Update all error paths to go to label free which is the only one valid until either the clock is enabled, or the MDIO bus is allocated and registered. This fixes kernel oops observed while trying to dereference the MDIO bus structure which is not yet allocated. Fixes: a1702857 ("net: Add support for the OpenCores 10/100 Mbps Ethernet MAC.") Signed-off-by:
-
pravin shelar authored
BugLink: https://bugs.launchpad.net/bugs/1878232 commit bbec7802 upstream. vxlan driver has bypass for local vxlan traffic, but that depends on information about all VNIs on local system in vxlan driver. This is not available in case of LWT. Therefore following patch disable encap bypass for LWT vxlan traffic. Fixes: ee122c79 ("vxlan: Flow based tunneling"). Reported-by:
Jakub Libosvar <jlibosva@redhat.com> Signed-off-by:
Jiri Benc <jbenc@redhat.com> Signed-off-by:
-
Arnd Bergmann authored
BugLink: https://bugs.launchpad.net/bugs/1878232 commit e8f967c3 upstream. gcc-7 detects a short memset in mvpp2, introduced in the original merge of the driver: drivers/net/ethernet/marvell/mvpp2.c: In function 'mvpp2_cls_init': drivers/net/ethernet/marvell/mvpp2.c:3296:2: error: 'memset' used with length equal to number of elements without multiplication by element size [-Werror=memset-elt-size] The result seems to be that we write uninitialized data into the flow table registers, although we did not get any warning about that uninitialized data usage. Using sizeof() lets us initialize then entire array instead. Fixes: 3f518509 ("ethernet: Add new driver for Marvell Armada 375 network unit") Signed-off-by:
Arnd Bergmann <arnd@arndb.de> Signed-off-by:
-
Geert Uytterhoeven authored
BugLink: https://bugs.launchpad.net/bugs/1878232 commit 7fa816b9 upstream. When reopening the network device on ra7795/salvator-x, e.g. after a DHCP timeout: IP-Config: Reopening network devices... genirq: Flags mismatch irq 139. 00000000 (eth0:ch24:emac) vs. 00000000 (eth0:ch24:emac) ravb e6800000.ethernet eth0: cannot request IRQ eth0:ch24:emac IP-Config: Failed to open eth0 IP-Config: No network devices available The "mismatch" is due to requesting an IRQ that is already in use, while IRQF_PROBE_SHARED wasn't set. However, the real cause is that ravb_close() doesn't release the R-Car Gen3-specific secondary IRQ. Add the missing free_irq() call to fix this. Fixes: 22d4df8f ("ravb: Add support for r8a7795 SoC") Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be> Acked-by:
-
Cyrille Pitchen authored
BugLink: https://bugs.launchpad.net/bugs/1878232 commit ba504994 upstream. macb_interrupt() should not use macb_writel(bp, ISR, <value>) but only queue_writel(queue, ISR, <value>). There is one IRQ and one set of {ISR, IER, IDR, IMR} [1] registers per queue on gem hardware, though only queue0 is actually used for now to receive frames: other queues can already be used to transmit frames. The queue_readl() and queue_writel() helper macros are designed to access the relevant IRQ registers. [1] ISR: Interrupt Status Register IER: Interrupt Enable Register IDR: Interrupt Disable Register IMR: Interrupt Mask Register Signed-off-by:
Cyrille Pitchen <cyrille.pitchen@atmel.com> Fixes: bfbb92c4 ("net: macb: Handle the RXUBR interrupt on all devices") Acked-by:
Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by:
-
Jisheng Zhang authored
BugLink: https://bugs.launchpad.net/bugs/1878232 commit 2c832293 upstream. When s->type is T_REG_64, the high 32bits are lost in val. This patch fixes this trivial issue. Signed-off-by:
Jisheng Zhang <jszhang@marvell.com> Fixes: 9b0cdefa ("net: mvneta: add ethtool statistics") Signed-off-by:
-
David Ahern authored
BugLink: https://bugs.launchpad.net/bugs/1878232 commit 9d1a6c4e upstream. icmp_send is called in response to some event. The skb may not have the device set (skb->dev is NULL), but it is expected to have an rt. Update icmp_route_lookup to use the rt on the skb to determine L3 domain. Fixes: 613d09b3 ("net: Use VRF device index for lookups on TX") Signed-off-by:
David Ahern <dsa@cumulusnetworks.com> Signed-off-by:
-
Krzysztof Kozlowski authored
BugLink: https://bugs.launchpad.net/bugs/1878232 commit 27d80fa8 upstream. Driver enabled runtime PM but did not revert this on removal. Re-binding of a device triggered warning: exynos-rng 10830400.rng: Unbalanced pm_runtime_enable! Fixes: b329669e ("hwrng: exynos - Add support for Exynos random number generator") Signed-off-by:
Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by:
-
Sabrina Dubroca authored
BugLink: https://bugs.launchpad.net/bugs/1878232 commit 2f86953e upstream. Tunnel deletion is delayed by both a workqueue (l2tp_tunnel_delete -> wq -> l2tp_tunnel_del_work) and RCU (sk_destruct -> RCU -> l2tp_tunnel_destruct). By the time l2tp_tunnel_destruct() runs to destroy the tunnel and finish destroying the socket, the private data reserved via the net_generic mechanism has already been freed, but l2tp_tunnel_destruct() actually uses this data. Make sure tunnel deletion for the netns has completed before returning from l2tp_exit_net() by first flushing the tunnel removal workqueue, and then waiting for RCU callbacks to complete. Fixes: 167eb17e ("l2tp: create tunnel sockets in the right namespace") Signed-off-by:
Sabrina Dubroca <sd@queasysnail.net> Signed-off-by:
-
xypron.glpk@gmx.de authored
BugLink: https://bugs.launchpad.net/bugs/1878232 commit 1740c29a upstream. ehea_get_port may return NULL. Do not dereference NULL value. Fixes: 8c4877a4 ("ehea: Use the standard logging functions") Signed-off-by:
Heinrich Schuchardt <xypron.glpk@gmx.de> Acked-by:
Thadeu Lima de Souza Cascardo <cascardo@debian.org> Signed-off-by:
-
Vivien Didelot authored
BugLink: https://bugs.launchpad.net/bugs/1878232 commit 996ecb82 upstream. In multi-chip systems, DSA Tag ports must learn SA addresses in order to correctly switch frames between interconnected chips. This fixes cross-chip hardware bridging in a VLAN filtering aware system, because a bridge group gets implemented as an hardware 802.1Q VLAN and thus DSA and user ports share the same FDB. Fixes: 4c7ea3c0 ("net: dsa: mv88e6xxx: disable SA learning for DSA and CPU ports") Signed-off-by:
-
Nikolay Aleksandrov authored
BugLink: https://bugs.launchpad.net/bugs/1878232 commit 85a3d4a9 upstream. pskb_may_pull may fail due to various reasons (e.g. alloc failure), but the skb isn't changed/dropped and processing continues so we shouldn't increment tx_dropped. CC: Kyeyoon Park <kyeyoonp@codeaurora.org> CC: Roopa Prabhu <roopa@cumulusnetworks.com> CC: Stephen Hemminger <stephen@networkplumber.org> CC: bridge@lists.linux-foundation.org Fixes: 95850116 ("bridge: Add support for IEEE 802.11 Proxy ARP") Signed-off-by:
Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by:
-
Johan Hovold authored
BugLink: https://bugs.launchpad.net/bugs/1878232 commit 2271150b upstream. Make sure to drop the reference taken by class_find_device() in hnae_get_handle() on errors and when later releasing the handle. Fixes: 6fe6611f ("net: add Hisilicon Network Subsystem...") Cc: Yisen Zhuang <yisen.zhuang@huawei.com> Cc: Salil Mehta <salil.mehta@huawei.com> Signed-off-by:
Johan Hovold <johan@kernel.org> Signed-off-by:
-
Johan Hovold authored
BugLink: https://bugs.launchpad.net/bugs/1878232 commit a7fe9d46 upstream. Make sure to deregister the primary device in case the secondary emac fails to probe. kernel BUG at /home/johan/work/omicron/src/linux/net/core/dev.c:7743! ... [<c05b3dec>] (free_netdev) from [<c04fe6c0>] (cpsw_probe+0x9cc/0xe50) [<c04fe6c0>] (cpsw_probe) from [<c047b28c>] (platform_drv_probe+0x5c/0xc0) Fixes: d9ba8f9e ("driver: net: ethernet: cpsw: dual emac interface implementation") Signed-off-by:
-
Johan Hovold authored
BugLink: https://bugs.launchpad.net/bugs/1878232 commit c7262aaa upstream. Make sure to drop the references taken by of_get_child_by_name() and bus_find_device() before returning from cpsw_phy_sel(). Note that holding a reference to the cpsw-phy-sel device does not prevent the devres-managed private data from going away. Fixes: 5892cd13 ("drivers: net: cpsw-phy-sel: Add new driver...") Cc: Mugunthan V N <mugunthanvnm@ti.com> Cc: Grygorii Strashko <grygorii.strashko@ti.com> Cc: linux-omap@vger.kernel.org Signed-off-by:
-
Andrew Lunn authored
BugLink: https://bugs.launchpad.net/bugs/1878232 commit 97db8afa upstream. The mvneta driver advertises it supports IFF_UNICAST_FLT. However, it actually does not. The hardware probably does support it, but there is no code to configure the filter. As a quick and simple fix, remove the flag. This will cause the core to fall back to promiscuous mode. Signed-off-by:
-
