- 25 Jan, 2016 40 commits
-
-
Dan Carpenter authored
commit 40d24c4d upstream. There are two issue here. 1) cnt starts as maxloop + 1 so all these loops iterate one more time than intended. 2) At the end of the loop we test for "if (maxloop && !cnt)" but for the first two loops, we end with cnt equal to -1. Changing this to a pre-op means we end with cnt set to 0. Fixes: cae86d4a ('mISDN: Add driver for Infineon ISDN chipset family') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Stefan Wahren authored
commit 4c02cba1 upstream. Currently the provided initial value for bcm2835_gpio_direction_output has no effect. So fix this issue by changing the value before changing the GPIO direction. As a result we need to move the function below bcm2835_gpio_set. Suggested-by: Martin Sperl <kernel@martin.sperl.org> Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com> Acked-by: Eric Anholt <eric@anholt.net> Acked-by: Stephen Warren <swarren@wwwdotorg.org> Fixes: e1b2dc70 ("pinctrl: add bcm2835 driver") Signed-off-by: Linus Walleij <linus.walleij@linaro.org> [ luis: backported to 3.16: - file rename: drivers/pinctrl/bcm/pinctrl-bcm2835.c -> drivers/pinctrl/pinctrl-bcm2835.c ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Tilman Schmidt authored
commit 4c5e354a upstream. When shutting down the device, the struct ser_cardstate must not be kfree()d immediately after the call to platform_device_unregister() since the embedded struct platform_device is still in use. Move the kfree() call to the release method instead. Signed-off-by: Tilman Schmidt <tilman@imap.cc> Fixes: 2869b23e ("drivers/isdn/gigaset: new M101 driver (v2)") Reported-by: Sasha Levin <sasha.levin@oracle.com> Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Hannes Frederic Sowa authored
commit 7bbadd2d upstream. Docbook does not like the definition of macros inside a field declaration and adds a warning. Move the definition out. Fixes: 79462ad0 ("net: add validation for the socket syscall protocol argument") Reported-by: kbuild test robot <lkp@intel.com> Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by: David S. Miller <davem@davemloft.net> [ kamal: backport to 3.13-stable: context ] Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Andrey Ryabinin authored
commit e459dfee upstream. ip6addrlbl_get() has never worked. If ip6addrlbl_hold() succeeded, ip6addrlbl_get() will exit with '-ESRCH'. If ip6addrlbl_hold() failed, ip6addrlbl_get() will use about to be free ip6addrlbl_entry pointer. Fix this by inverting ip6addrlbl_hold() check. Fixes: 2a8cc6c8 ("[IPV6] ADDRCONF: Support RFC3484 configurable address selection policy table.") Signed-off-by: Andrey Ryabinin <aryabinin@virtuozzo.com> Reviewed-by: Cong Wang <cwang@twopensource.com> Acked-by: YOSHIFUJI Hideaki <yoshfuji@linux-ipv6.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Paolo Bonzini authored
commit e5e57e7a upstream. While setting the KVM PIT counters in 'kvm_pit_load_count', if 'hpet_legacy_start' is set, the function disables the timer on channel[0], instead of the respective index 'channel'. This is because channels 1-3 are not linked to the HPET. Fix the caller to only activate the special HPET processing for channel 0. Reported-by: P J P <pjp@fedoraproject.org> Fixes: 0185604cSigned-off-by: Paolo Bonzini <pbonzini@redhat.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Andrea Arcangeli authored
commit ff4319dc upstream. The dmi_ver wasn't updated correctly before the dmi_decode method run to save the uuid. That resulted in "dmidecode -s system-uuid" and /sys/class/dmi/id/product_uuid disagreeing. The latter was buggy and this fixes it. Reported-by: Federico Simoncelli <fsimonce@redhat.com> Fixes: 9f9c9cbb ("drivers/firmware/dmi_scan.c: fetch dmi version from SMBIOS if it exists") Fixes: 79bae42d ("dmi_scan: refactor dmi_scan_machine(), {smbios,dmi}_present()") Signed-off-by: Andrea Arcangeli <aarcange@redhat.com> Signed-off-by: Jean Delvare <jdelvare@suse.de> [ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Michal Hocko authored
commit 751e5f5c upstream. kernel test robot has reported the following crash: BUG: unable to handle kernel NULL pointer dereference at 00000100 IP: [<c1074df6>] __queue_work+0x26/0x390 *pdpt = 0000000000000000 *pde = f000ff53f000ff53 *pde = f000ff53f000ff53 Oops: 0000 [#1] PREEMPT PREEMPT SMP SMP CPU: 0 PID: 24 Comm: kworker/0:1 Not tainted 4.4.0-rc4-00139-g373ccbe5 #1 Workqueue: events vmstat_shepherd task: cb684600 ti: cb7ba000 task.ti: cb7ba000 EIP: 0060:[<c1074df6>] EFLAGS: 00010046 CPU: 0 EIP is at __queue_work+0x26/0x390 EAX: 00000046 EBX: cbb37800 ECX: cbb37800 EDX: 00000000 ESI: 00000000 EDI: 00000000 EBP: cb7bbe68 ESP: cb7bbe38 DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068 CR0: 8005003b CR2: 00000100 CR3: 01fd5000 CR4: 000006b0 Stack: Call Trace: __queue_delayed_work+0xa1/0x160 queue_delayed_work_on+0x36/0x60 vmstat_shepherd+0xad/0xf0 process_one_work+0x1aa/0x4c0 worker_thread+0x41/0x440 kthread+0xb0/0xd0 ret_from_kernel_thread+0x21/0x40 The reason is that start_shepherd_timer schedules the shepherd work item which uses vmstat_wq (vmstat_shepherd) before setup_vmstat allocates that workqueue so if the further initialization takes more than HZ we might end up scheduling on a NULL vmstat_wq. This is really unlikely but not impossible. Fixes: 373ccbe5 ("mm, vmstat: allow WQ concurrency to discover memory reclaim doesn't make any progress") Reported-by: kernel test robot <ying.huang@linux.intel.com> Signed-off-by: Michal Hocko <mhocko@suse.com> Tested-by: Tetsuo Handa <penguin-kernel@i-love.sakura.ne.jp> Cc: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Cc: Ben Hutchings <ben@decadent.org.uk> [ luis: backported to 3.16: based on Ben's backport to 3.2: - as with 3.2, there's a similar race but with the CPU hotplug code ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com> [ kamal: backport to 3.13-stable: context ] Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Steven Rostedt (Red Hat) authored
commit 049fb9bd upstream. If the module init code fails after calling ftrace_module_init() and before calling do_init_module(), we can suffer from a memory leak. This is because ftrace_module_init() allocates pages to store the locations that ftrace hooks are placed in the module text. If do_init_module() fails, it still calls the MODULE_GOING notifiers which will tell ftrace to do a clean up of the pages it allocated for the module. But if load_module() fails before then, the pages allocated by ftrace_module_init() will never be freed. Call ftrace_release_mod() on the module if load_module() fails before getting to do_init_module(). Link: http://lkml.kernel.org/r/567CEA31.1070507@intel.comReported-by: "Qiu, PeiyangX" <peiyangx.qiu@intel.com> Fixes: a949ae56 "ftrace/module: Hardcode ftrace_module_init() call into load_module()" Acked-by: Rusty Russell <rusty@rustcorp.com.au> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> [ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Roman Volkov authored
commit 0f090bf1 upstream. Since WM8650 has the same 'WMT' SDHC controller as WM8505, and the driver is already in the kernel, this node enables the controller support for WM8650 Signed-off-by: Roman Volkov <rvolkov@v1ros.org> Reviewed-by: Alexey Charkov <alchark@gmail.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
NeilBrown authored
commit b02bab6b upstream. These async_XX functions are called from md/raid5 in an atomic section, between get_cpu() and put_cpu(), so they must not sleep. So use GFP_NOWAIT rather than GFP_IO. Dan Williams writes: Longer term async_tx needs to be merged into md directly as we can allocate this unmap data statically per-stripe rather than per request. Fixed: 7476bd79 ("async_pq: convert to dmaengine_unmap_data") Reported-and-tested-by: Stanislav Samsonov <slava@annapurnalabs.com> Acked-by: Dan Williams <dan.j.williams@intel.com> Signed-off-by: NeilBrown <neilb@suse.com> Signed-off-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Qiu Peiyang authored
commit f36d1be2 upstream. When we do cat /sys/kernel/debug/tracing/printk_formats, we hit kernel panic at t_show. general protection fault: 0000 [#1] PREEMPT SMP CPU: 0 PID: 2957 Comm: sh Tainted: G W O 3.14.55-x86_64-01062-gd4acdc7 #2 RIP: 0010:[<ffffffff811375b2>] [<ffffffff811375b2>] t_show+0x22/0xe0 RSP: 0000:ffff88002b4ebe80 EFLAGS: 00010246 RAX: 0000000000000000 RBX: 0000000000000000 RCX: 0000000000000004 RDX: 0000000000000004 RSI: ffffffff81fd26a6 RDI: ffff880032f9f7b1 RBP: ffff88002b4ebe98 R08: 0000000000001000 R09: 000000000000ffec R10: 0000000000000000 R11: 000000000000000f R12: ffff880004d9b6c0 R13: 7365725f6d706400 R14: ffff880004d9b6c0 R15: ffffffff82020570 FS: 0000000000000000(0000) GS:ffff88003aa00000(0063) knlGS:00000000f776bc40 CS: 0010 DS: 002b ES: 002b CR0: 0000000080050033 CR2: 00000000f6c02ff0 CR3: 000000002c2b3000 CR4: 00000000001007f0 Call Trace: [<ffffffff811dc076>] seq_read+0x2f6/0x3e0 [<ffffffff811b749b>] vfs_read+0x9b/0x160 [<ffffffff811b7f69>] SyS_read+0x49/0xb0 [<ffffffff81a3a4b9>] ia32_do_call+0x13/0x13 ---[ end trace 5bd9eb630614861e ]--- Kernel panic - not syncing: Fatal exception When the first time find_next calls find_next_mod_format, it should iterate the trace_bprintk_fmt_list to find the first print format of the module. However in current code, start_index is smaller than *pos at first, and code will not iterate the list. Latter container_of will get the wrong address with former v, which will cause mod_fmt be a meaningless object and so is the returned mod_fmt->fmt. This patch will fix it by correcting the start_index. After fixed, when the first time calls find_next_mod_format, start_index will be equal to *pos, and code will iterate the trace_bprintk_fmt_list to get the right module printk format, so is the returned mod_fmt->fmt. Link: http://lkml.kernel.org/r/5684B900.9000309@intel.com Fixes: 102c9323 "tracing: Add __tracepoint_string() to export string pointers" Signed-off-by: Qiu Peiyang <peiyangx.qiu@intel.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Colin Ian King authored
commit 713a3e4d upstream. Fix build warning: scripts/recordmcount.c:589:4: warning: format not a string literal and no format arguments [-Wformat-security] sprintf("%s: failed\n", file); Fixes: a50bd439 ("ftrace/scripts: Have recordmcount copy the object file") Link: http://lkml.kernel.org/r/1451516801-16951-1-git-send-email-colin.king@canonical.com Cc: Li Bin <huawei.libin@huawei.com> Cc: Russell King <rmk+kernel@arm.linux.org.uk> Cc: Will Deacon <will.deacon@arm.com> Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Andrew Banman authored
commit 5f0f2887 upstream. test_pages_in_a_zone() does not account for the possibility of missing sections in the given pfn range. pfn_valid_within always returns 1 when CONFIG_HOLES_IN_ZONE is not set, allowing invalid pfns from missing sections to pass the test, leading to a kernel oops. Wrap an additional pfn loop with PAGES_PER_SECTION granularity to check for missing sections before proceeding into the zone-check code. This also prevents a crash from offlining memory devices with missing sections. Despite this, it may be a good idea to keep the related patch '[PATCH 3/3] drivers: memory: prohibit offlining of memory blocks with missing sections' because missing sections in a memory block may lead to other problems not covered by the scope of this fix. Signed-off-by: Andrew Banman <abanman@sgi.com> Acked-by: Alex Thorlton <athorlton@sgi.com> Cc: Russ Anderson <rja@sgi.com> Cc: Alex Thorlton <athorlton@sgi.com> Cc: Yinghai Lu <yinghai@kernel.org> Cc: Greg KH <greg@kroah.com> Cc: Seth Jennings <sjennings@variantweb.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Nikesh Oswal authored
commit e73694d8 upstream. For a sample rate of 12kHz the bclk was taken from the 44.1kHz table as we test for a multiple of 8kHz. This patch fixes this issue by testing for multiples of 4kHz instead. Signed-off-by: Nikesh Oswal <Nikesh.Oswal@cirrus.com> Signed-off-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Mario Kleiner authored
commit 9f660a1c upstream. Without this patch, internal speaker and line-out work, but front headphone output jack stays silent on the Mac Pro 4,1. This code path also gets executed on the MacPro 5,1 due to identical codec SSID, but i don't know if it has any positive or adverse effects there or not. (v2) Implement feedback from Takashi Iwai: Reuse alc889_fixup_mbp_vref and just add a new nid 0x19 for the MacPro 4,1. Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Helge Deller authored
commit 71a71fb5 upstream. On parisc syscalls which are interrupted by signals sometimes failed to restart and instead returned -ENOSYS which in the worst case lead to userspace crashes. A similiar problem existed on MIPS and was fixed by commit e967ef02 ("MIPS: Fix restart of indirect syscalls"). On parisc the current syscall restart code assumes that all syscall callers load the syscall number in the delay slot of the ble instruction. That's how it is e.g. done in the unistd.h header file: ble 0x100(%sr2, %r0) ldi #syscall_nr, %r20 Because of that assumption the current code never restored %r20 before returning to userspace. This assumption is at least not true for code which uses the glibc syscall() function, which instead uses this syntax: ble 0x100(%sr2, %r0) copy regX, %r20 where regX depend on how the compiler optimizes the code and register usage. This patch fixes this problem by adding code to analyze how the syscall number is loaded in the delay branch and - if needed - copy the syscall number to regX prior returning to userspace for the syscall restart. Signed-off-by: Helge Deller <deller@gmx.de> Cc: Mathieu Desnoyers <mathieu.desnoyers@efficios.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Ashok Raj authored
commit d90167a9 upstream. Intel's MCA implementation broadcasts MCEs to all CPUs on the node. This poses a problem for offlined CPUs which cannot participate in the rendezvous process: Kernel panic - not syncing: Timeout: Not all CPUs entered broadcast exception handler Kernel Offset: disabled Rebooting in 100 seconds.. More specifically, Linux does a soft offline of a CPU when writing a 0 to /sys/devices/system/cpu/cpuX/online, which doesn't prevent the #MC exception from being broadcasted to that CPU. Ensure that offline CPUs don't participate in the MCE rendezvous and clear the RIP valid status bit so that a second MCE won't cause a shutdown. Without the patch, mce_start() will increment mce_callin and wait for all CPUs. Offlined CPUs should avoid participating in the rendezvous process altogether. Signed-off-by: Ashok Raj <ashok.raj@intel.com> [ Massage commit message. ] Signed-off-by: Borislav Petkov <bp@suse.de> Reviewed-by: Tony Luck <tony.luck@intel.com> Cc: H. Peter Anvin <hpa@zytor.com> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: linux-edac <linux-edac@vger.kernel.org> Link: http://lkml.kernel.org/r/1449742346-21470-2-git-send-email-bp@alien8.deSigned-off-by: Ingo Molnar <mingo@kernel.org> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Alan Stern authored
commit e50293ef upstream. Commit 8520f380 ("USB: change hub initialization sleeps to delayed_work") changed the hub_activate() routine to make part of it run in a workqueue. However, the commit failed to take a reference to the usb_hub structure or to lock the hub interface while doing so. As a result, if a hub is plugged in and quickly unplugged before the work routine can run, the routine will try to access memory that has been deallocated. Or, if the hub is unplugged while the routine is running, the memory may be deallocated while it is in active use. This patch fixes the problem by taking a reference to the usb_hub at the start of hub_activate() and releasing it at the end (when the work is finished), and by locking the hub interface while the work routine is running. It also adds a check at the start of the routine to see if the hub has already been disconnected, in which nothing should be done. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Reported-by: Alexandru Cornea <alexandru.cornea@intel.com> Tested-by: Alexandru Cornea <alexandru.cornea@intel.com> Fixes: 8520f380 ("USB: change hub initialization sleeps to delayed_work") Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> [ luis: backported to 3.16: - Added forward declaration of hub_release() which mainline had with commit 32a69589 ("usb: hub: convert khubd into workqueue") ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Dan Carpenter authored
commit abdc9a3b upstream. The code expects the loop to end with "retries" set to zero but, because it is a post-op, it will end set to -1. I have fixed this by moving the decrement inside the loop. Fixes: 014aa2a3 ('USB: ipaq: minor ipaq_open() cleanup.') Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Konrad Rzeszutek Wilk authored
commit 408fb0e5 upstream. commit f598282f ("PCI: Fix the NIU MSI-X problem in a better way") teaches us that dealing with MSI-X can be troublesome. Further checks in the MSI-X architecture shows that if the PCI_COMMAND_MEMORY bit is turned of in the PCI_COMMAND we may not be able to access the BAR (since they are memory regions). Since the MSI-X tables are located in there.. that can lead to us causing PCIe errors. Inhibit us performing any operation on the MSI-X unless the MEMORY bit is set. Note that Xen hypervisor with: "x86/MSI-X: access MSI-X table only after having enabled MSI-X" will return: xen_pciback: 0000:0a:00.1: error -6 enabling MSI-X for guest 3! When the generic MSI code tries to setup the PIRQ without MEMORY bit set. Which means with later versions of Xen (4.6) this patch is not neccessary. This is part of XSA-157 Reviewed-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Konrad Rzeszutek Wilk authored
commit 7cfb905b upstream. Otherwise just continue on, returning the same values as previously (return of 0, and op->result has the PIRQ value). This does not change the behavior of XEN_PCI_OP_disable_msi[|x]. The pci_disable_msi or pci_disable_msix have the checks for msi_enabled or msix_enabled so they will error out immediately. However the guest can still call these operations and cause us to disable the 'ack_intr'. That means the backend IRQ handler for the legacy interrupt will not respond to interrupts anymore. This will lead to (if the device is causing an interrupt storm) for the Linux generic code to disable the interrupt line. Naturally this will only happen if the device in question is plugged in on the motherboard on shared level interrupt GSI. This is part of XSA-157 Reviewed-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Konrad Rzeszutek Wilk authored
commit a396f3a2 upstream. Otherwise an guest can subvert the generic MSI code to trigger an BUG_ON condition during MSI interrupt freeing: for (i = 0; i < entry->nvec_used; i++) BUG_ON(irq_has_action(entry->irq + i)); Xen PCI backed installs an IRQ handler (request_irq) for the dev->irq whenever the guest writes PCI_COMMAND_MEMORY (or PCI_COMMAND_IO) to the PCI_COMMAND register. This is done in case the device has legacy interrupts the GSI line is shared by the backend devices. To subvert the backend the guest needs to make the backend to change the dev->irq from the GSI to the MSI interrupt line, make the backend allocate an interrupt handler, and then command the backend to free the MSI interrupt and hit the BUG_ON. Since the backend only calls 'request_irq' when the guest writes to the PCI_COMMAND register the guest needs to call XEN_PCI_OP_enable_msi before any other operation. This will cause the generic MSI code to setup an MSI entry and populate dev->irq with the new PIRQ value. Then the guest can write to PCI_COMMAND PCI_COMMAND_MEMORY and cause the backend to setup an IRQ handler for dev->irq (which instead of the GSI value has the MSI pirq). See 'xen_pcibk_control_isr'. Then the guest disables the MSI: XEN_PCI_OP_disable_msi which ends up triggering the BUG_ON condition in 'free_msi_irqs' as there is an IRQ handler for the entry->irq (dev->irq). Note that this cannot be done using MSI-X as the generic code does not over-write dev->irq with the MSI-X PIRQ values. The patch inhibits setting up the IRQ handler if MSI or MSI-X (for symmetry reasons) code had been called successfully. P.S. Xen PCIBack when it sets up the device for the guest consumption ends up writting 0 to the PCI_COMMAND (see xen_pcibk_reset_device). XSA-120 addendum patch removed that - however when upstreaming said addendum we found that it caused issues with qemu upstream. That has now been fixed in qemu upstream. This is part of XSA-157 Reviewed-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Konrad Rzeszutek Wilk authored
commit 5e0ce145 upstream. The guest sequence of: a) XEN_PCI_OP_enable_msix b) XEN_PCI_OP_enable_msix results in hitting an NULL pointer due to using freed pointers. The device passed in the guest MUST have MSI-X capability. The a) constructs and SysFS representation of MSI and MSI groups. The b) adds a second set of them but adding in to SysFS fails (duplicate entry). 'populate_msi_sysfs' frees the newly allocated msi_irq_groups (note that in a) pdev->msi_irq_groups is still set) and also free's ALL of the MSI-X entries of the device (the ones allocated in step a) and b)). The unwind code: 'free_msi_irqs' deletes all the entries and tries to delete the pdev->msi_irq_groups (which hasn't been set to NULL). However the pointers in the SysFS are already freed and we hit an NULL pointer further on when 'strlen' is attempted on a freed pointer. The patch adds a simple check in the XEN_PCI_OP_enable_msix to guard against that. The check for msi_enabled is not stricly neccessary. This is part of XSA-157 Reviewed-by: David Vrabel <david.vrabel@citrix.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Konrad Rzeszutek Wilk authored
commit 56441f3c upstream. The guest sequence of: a) XEN_PCI_OP_enable_msi b) XEN_PCI_OP_enable_msi c) XEN_PCI_OP_disable_msi results in hitting an BUG_ON condition in the msi.c code. The MSI code uses an dev->msi_list to which it adds MSI entries. Under the above conditions an BUG_ON() can be hit. The device passed in the guest MUST have MSI capability. The a) adds the entry to the dev->msi_list and sets msi_enabled. The b) adds a second entry but adding in to SysFS fails (duplicate entry) and deletes all of the entries from msi_list and returns (with msi_enabled is still set). c) pci_disable_msi passes the msi_enabled checks and hits: BUG_ON(list_empty(dev_to_msi_list(&dev->dev))); and blows up. The patch adds a simple check in the XEN_PCI_OP_enable_msi to guard against that. The check for msix_enabled is not stricly neccessary. This is part of XSA-157. Reviewed-by: David Vrabel <david.vrabel@citrix.com> Reviewed-by: Jan Beulich <jbeulich@suse.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Konrad Rzeszutek Wilk authored
commit 8135cf8b upstream. Double fetch vulnerabilities that happen when a variable is fetched twice from shared memory but a security check is only performed the first time. The xen_pcibk_do_op function performs a switch statements on the op->cmd value which is stored in shared memory. Interestingly this can result in a double fetch vulnerability depending on the performed compiler optimization. This patch fixes it by saving the xen_pci_op command before processing it. We also use 'barrier' to make sure that the compiler does not perform any optimization. This is part of XSA155. Reviewed-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Jan Beulich <JBeulich@suse.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Roger Pau Monné authored
commit 18779149 upstream. Since indirect descriptors are in memory shared with the frontend, the frontend could alter the first_sect and last_sect values after they have been validated but before they are recorded in the request. This may result in I/O requests that overflow the foreign page, possibly overwriting local pages when the I/O request is executed. When parsing indirect descriptors, only read first_sect and last_sect once. This is part of XSA155. Signed-off-by: Roger Pau Monné <roger.pau@citrix.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> [ luis: backported to 3.16: - Use ACCESS_ONCE instead of READ_ONCE - Use PAGE_SIZE instead of XEN_PAGE_SIZE ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Roger Pau Monné authored
commit 1f13d75c upstream. A compiler may load a switch statement value multiple times, which could be bad when the value is in memory shared with the frontend. When converting a non-native request to a native one, ensure that src->operation is only loaded once by using READ_ONCE(). This is part of XSA155. Signed-off-by: Roger Pau Monné <roger.pau@citrix.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> [ luis: backported to 3.16: - replaced READ_ONCE() by ACCESS_ONCE() ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
David Vrabel authored
commit 68a33bfd upstream. Instead of open-coding memcpy()s and directly accessing Tx and Rx requests, use the new RING_COPY_REQUEST() that ensures the local copy is correct. This is more than is strictly necessary for guest Rx requests since only the id and gref fields are used and it is harmless if the frontend modifies these. This is part of XSA155. Reviewed-by: Wei Liu <wei.liu2@citrix.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> [ kamal: backport to 3.13-stable: context (s/queue/vif/) ] Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
David Vrabel authored
commit 0f589967 upstream. The last from guest transmitted request gives no indication about the minimum amount of credit that the guest might need to send a packet since the last packet might have been a small one. Instead allow for the worst case 128 KiB packet. This is part of XSA155. Reviewed-by: Wei Liu <wei.liu2@citrix.com> Signed-off-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> [ kamal: backport to 3.13-stable: context ] Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
David Vrabel authored
commit 454d5d88 upstream. Using RING_GET_REQUEST() on a shared ring is easy to use incorrectly (i.e., by not considering that the other end may alter the data in the shared ring while it is being inspected). Safe usage of a request generally requires taking a local copy. Provide a RING_COPY_REQUEST() macro to use instead of RING_GET_REQUEST() and an open-coded memcpy(). This takes care of ensuring that the copy is done correctly regardless of any possible compiler optimizations. Use a volatile source to prevent the compiler from reordering or omitting the copy. This is part of XSA155. Signed-off-by: David Vrabel <david.vrabel@citrix.com> Signed-off-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Michael Holzheu authored
commit 272fa59c upstream. The print_insn() function returns strings like "lghi %r1,0". To escape the '%' character in sprintf() a second '%' is used. For example "lghi %%r1,0" is converted into "lghi %r1,0". After print_insn() the output string is passed to printk(). Because format specifiers like "%r" or "%f" are ignored by printk() this works by chance most of the time. But for instructions with control registers like "lctl %c6,%c6,780" this fails because printk() interprets "%c" as character format specifier. Fix this problem and escape the '%' characters twice. For example "lctl %%%%c6,%%%%c6,780" is then converted by sprintf() into "lctl %%c6,%%c6,780" and by printk() into "lctl %c6,%c6,780". Signed-off-by: Michael Holzheu <holzheu@linux.vnet.ibm.com> Signed-off-by: Martin Schwidefsky <schwidefsky@de.ibm.com> [ luis: backported to 3.16: - drop condition with OPERAND_VR introduced only with commit 3585cb02 ("s390/disassembler: add vector instructions") ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Xiong Zhang authored
commit 3e6db33a upstream. It takes three minutes to enter into hibernation on some OEM SKL machines and we see many codec spurious response after thaw() opertion. This is because HDA is still in D0 state after freeze() call and pci_pm_freeze/pci_pm_freeze_noirq() don't set D3 hot in pci_bus driver. It seems bios still access HDA when system enter into freeze state, HDA will receive codec response interrupt immediately after thaw() call. Because of this unexpected interrupt, HDA enter into a abnormal state and slow down the system enter into hibernation. In this patch, we put HDA into D3 hot state in azx_freeze_noirq() and put HDA into D0 state in azx_thaw_noirq(). V2: Only apply this fix to SKL+ Fix compile error when CONFIG_PM_SLEEP isn't defined [Yet another fix for CONFIG_PM_SLEEP ifdef and the additional comment by tiwai] Signed-off-by: Xiong Zhang <xiong.y.zhang@intel.com> Signed-off-by: Takashi Iwai <tiwai@suse.de> [ luis: backported to 3.16: adjusted context ] Signed-off-by: Luis Henriques <luis.henriques@canonical.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Vineet Gupta authored
commit 323f41f9 upstream. ARC dwarf unwinder only supports CIE version == 1 The boot time dwarf sanitizer (part of binary lookup table constructor) would simply bail if it saw CIE version == 3, rendering unwinder with a NULL lookup table. It seems libgcc linked with kernel does have such entries. With fallback linear search removed, and a NULL binary lookup table, unwinder fails to generate any stack trace. So allow graceful ignoring of unsupported CIE entries. This problem was initially seen in Alexey's setup (and not mine) as he was using buildroot built toolchain (libgcc) which doesn't get built with CFLAGS_FOR_TARGET="-gdwarf-2 which is my default Fixes STAR 9000985048: "kernel unwinder broken with stock tools" Fixes: 2e22502c ARC: dw2 unwind: Remove falllback linear search thru FDE entries Reported-by Alexey Brodkin <abrodkin@synopsys.com> Signed-off-by: Vineet Gupta <vgupta@synopsys.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Vineet Gupta authored
commit bc79c9a7 upstream. The fix which removed linear searching of dwarf (because binary lookup data always exists) missed out on the fact that modules don't get the binary lookup tables info. This caused unwinding out of modules to stop working. So add binary lookup header setup (equivalent of eh_frame_hdr setup) to modules as well. While at it, confine the header setup to within unwinder code, reducing one API exposed out of unwinder code. Fixes: 2e22502c ARC: dw2 unwind: Remove falllback linear search thru FDE entries Signed-off-by: Vineet Gupta <vgupta@synopsys.com> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Steven Rostedt (Red Hat) authored
commit a50bd439 upstream. Russell King found that he had weird side effects when compiling the kernel with hard linked ccache. The reason was that recordmcount modified the kernel in place via mmap, and when a file gets modified twice by recordmcount, it will complain about it. To fix this issue, Russell wrote a patch that checked if the file was hard linked more than once and would unlink it if it was. Linus Torvalds was not happy with the fact that recordmcount does this in place modification. Instead of doing the unlink only if the file has two or more hard links, it does the unlink all the time. In otherwords, it always does a copy if it changed something. That is, it does the write out if a change was made. Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Russell King authored
commit dd39a265 upstream. recordmcount edits the file in-place, which can cause problems when using ccache in hardlink mode. Arrange for recordmcount to break a hardlinked object. Link: http://lkml.kernel.org/r/E1a7MVT-0000et-62@rmk-PC.arm.linux.org.ukSigned-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Johan Hovold authored
commit 157f38f9 upstream. Fix parent-device reference leak due to SPI-core taking an unnecessary reference to the parent when allocating the master structure, a reference that was never released. Note that driver core takes its own reference to the parent when the master device is registered. Fixes: 49dce689 ("spi doesn't need class_device") Signed-off-by: Johan Hovold <johan@kernel.org> Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Anson Huang authored
commit fa0708b3 upstream. In cpu_v7_do_suspend routine, r11 is used while it is NOT saved/restored, different compiler may have different usage of ARM general registers, so it may cause issues during calling cpu_v7_do_suspend. We meet kernel fault occurs when using GCC 4.8.3, r11 contains valid value before calling into cpu_v7_do_suspend, but when returned from this routine, r11 is corrupted and lead to kernel fault. Doing save/restore for those corrupted registers is a must in assemble code. Signed-off-by: Anson Huang <Anson.Huang@freescale.com> Reviewed-by: Nicolas Pitre <nico@linaro.org> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-
Anssi Hannula authored
commit 42e3121d upstream. AudioQuest DragonFly DAC reports a volume control range of 0..50 (0x0000..0x0032) which in USB Audio means a range of 0 .. 0.2dB, which is obviously incorrect and would cause software using the dB information in e.g. volume sliders to have a massive volume difference in 100..102% range. Commit 2d1cb7f6 ("ALSA: usb-audio: add dB range mapping for some devices") added a dB range mapping for it with range 0..50 dB. However, the actual volume mapping seems to be neither linear volume nor linear dB scale, but instead quite close to the cubic mapping e.g. alsamixer uses, with a range of approx. -53...0 dB. Replace the previous quirk with a custom dB mapping based on some basic output measurements, using a 10-item range TLV (which will still fit in alsa-lib MAX_TLV_RANGE_SIZE). Tested on AudioQuest DragonFly HW v1.2. The quirk is only applied if the range is 0..50, so if this gets fixed/changed in later HW revisions it will no longer be applied. v2: incorporated Takashi Iwai's suggestion for the quirk application method Signed-off-by: Anssi Hannula <anssi.hannula@iki.fi> Signed-off-by: Takashi Iwai <tiwai@suse.de> [ kamal: backport to 3.13-stable: use snd_printk instead of usb_audio_info ] Signed-off-by: Kamal Mostafa <kamal@canonical.com>
-