A hot-removed CPU may have ID that is numerically larger than the number of
existing CPUs in the system (e.g. we can unplug CPU 4 from a system that
has CPUs 0, 1 and 4).

Thus the WARN_ONs should check whether the CPU in question is currently
present, not whether its ID value is less than num_present_cpus().

Cc: Ingo Molnar <mingo@kernel.org>
Cc: Juri Lelli <juri.lelli@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Reported-by: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1392646353-1874-1-git-send-email-boris.ostrovsky@oracle.comSigned-off-by: Thomas Gleixner <tglx@linutronix.de>

Because of a recent syscall design debate; its deemed appropriate for
each syscall to have a flags argument for future extension; without
immediately requiring new syscalls.

Cc: juri.lelli@gmail.com
Cc: Ingo Molnar <mingo@redhat.com>
Suggested-by: Michael Kerrisk <mtk.manpages@gmail.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140214161929.GL27965@twins.programming.kicks-ass.netSigned-off-by: Thomas Gleixner <tglx@linutronix.de>

We're copying the on-stack structure to userspace, but forgot to give
the right number of bytes to copy. This allows the calling process to
obtain up to PAGE_SIZE bytes from the stack (and possibly adjacent
kernel memory).

This fix copies only as much as we actually have on the stack
(attr->size defaults to the size of the struct) and leaves the rest of
the userspace-provided buffer untouched.

Found using kmemcheck + trinity.

Fixes: d50dde5a ("sched: Add new scheduler syscalls to support an extended scheduling parameters ABI")
Cc: Dario Faggioli <raistlin@linux.it>
Cc: Juri Lelli <juri.lelli@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Vegard Nossum <vegard.nossum@oracle.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1392585857-10725-1-git-send-email-vegard.nossum@oracle.comSigned-off-by: Thomas Gleixner <tglx@linutronix.de>

Normally task_numa_work scans over a fairly small amount of memory,
but it is possible to run into a large unpopulated part of virtual
memory, with no pages mapped. In that case, task_numa_work can run
for a while, and it may make sense to reschedule as required.

Cc: akpm@linux-foundation.org
Cc: Andrea Arcangeli <aarcange@redhat.com>
Signed-off-by: Rik van Riel <riel@redhat.com>
Reported-by: Xing Gang <gang.xing@hp.com>
Tested-by: Chegu Vinod <chegu_vinod@hp.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1392761566-24834-2-git-send-email-riel@redhat.comSigned-off-by: Thomas Gleixner <tglx@linutronix.de>

Fix this lockdep warning:

[   44.804600] =========================================================
[   44.805746] [ INFO: possible irq lock inversion dependency detected ]
[   44.805746] 3.14.0-rc2-test+ #14 Not tainted
[   44.805746] ---------------------------------------------------------
[   44.805746] bash/3674 just changed the state of lock:
[   44.805746]  (&dl_b->lock){+.....}, at: [<ffffffff8106ad15>] sched_rt_handler+0x132/0x248
[   44.805746] but this lock was taken by another, HARDIRQ-safe lock in the past:
[   44.805746]  (&rq->lock){-.-.-.}

and interrupts could create inverse lock ordering between them.

[   44.805746]
[   44.805746] other info that might help us debug this:
[   44.805746]  Possible interrupt unsafe locking scenario:
[   44.805746]
[   44.805746]        CPU0                    CPU1
[   44.805746]        ----                    ----
[   44.805746]   lock(&dl_b->lock);
[   44.805746]                                local_irq_disable();
[   44.805746]                                lock(&rq->lock);
[   44.805746]                                lock(&dl_b->lock);
[   44.805746]   <Interrupt>
[   44.805746]     lock(&rq->lock);

by making dl_b->lock acquiring always IRQ safe.

Cc: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Juri Lelli <juri.lelli@gmail.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1392107067-19907-3-git-send-email-juri.lelli@gmail.comSigned-off-by: Thomas Gleixner <tglx@linutronix.de>

Don't compare sysctl_sched_rt_runtime against sysctl_sched_rt_period if
the former is equal to RUNTIME_INF, otherwise disabling -rt bandwidth
management (with CONFIG_RT_GROUP_SCHED=n) fails.

Cc: Ingo Molnar <mingo@redhat.com>
Signed-off-by: Juri Lelli <juri.lelli@gmail.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1392107067-19907-2-git-send-email-juri.lelli@gmail.comSigned-off-by: Thomas Gleixner <tglx@linutronix.de>

While debugging the crash with the bad nr_running accounting, I hit
another bug where, after running my sched deadline test, I was getting
failures to take a CPU offline. It was giving me a -EBUSY error.

Adding a bunch of trace_printk()s around, I found that the cpu
notifier that called sched_cpu_inactive() was returning a failure. The
overflow value was coming up negative?

Talking this over with Juri, the problem is that the total_bw update was
suppose to be made by dl_overflow() which, during my tests, seemed to
not be called. Adding more trace_printk()s, it wasn't that it wasn't
called, but it exited out right away with the check of new_bw being
equal to p->dl.dl_bw. The new_bw calculates the ratio between period and
runtime. The bug is that if you set a deadline, you do not need to set
a period if you plan on the period being equal to the deadline. That
is, if period is zero and deadline is not, then the system call should
set the period to be equal to the deadline. This is done elsewhere in
the code.

The fix is easy, check if period is set, and if it is not, then use the
deadline.

Cc: Juri Lelli <juri.lelli@gmail.com>
Cc: Ingo Molnar <mingo@kernel.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/20140219135335.7e74abd4@gandalf.local.homeSigned-off-by: Thomas Gleixner <tglx@linutronix.de>

Rostedt writes:

My test suite was locking up hard when enabling mmiotracer. This was due
to the mmiotracer placing all but one CPU offline. I found this out
when I was able to reproduce the bug with just my stress-cpu-hotplug
test. This bug baffled me because it would not always trigger, and
would only trigger on the first run after boot up. The
stress-cpu-hotplug test would crash hard the first run, or never crash
at all. But a new reboot may cause it to crash on the first run again.

I spent all week bisecting this, as I couldn't find a consistent
reproducer. I finally narrowed it down to the sched deadline patches,
and even more peculiar, to the commit that added the sched
deadline boot up self test to the latency tracer. Then it dawned on me
to what the bug was.

All it took was to run a task under sched deadline to screw up the CPU
hot plugging. This explained why it would lock up only on the first run
of the stress-cpu-hotplug test. The bug happened when the boot up self
test of the schedule latency tracer would test a deadline task. The
deadline task would corrupt something that would cause CPU hotplug to
fail. If it didn't corrupt it, the stress test would always work
(there's no other sched deadline tasks that would run to cause
problems). If it did corrupt on boot up, the first test would lockup
hard.

I proved this theory by running my deadline test program on another box,
and then run the stress-cpu-hotplug test, and it would now consistently
lock up. I could run stress-cpu-hotplug over and over with no problem,
but once I ran the deadline test, the next run of the
stress-cpu-hotplug would lock hard.

After adding lots of tracing to the code, I found the cause. The
function tracer showed that migrate_tasks() was stuck in an infinite
loop, where rq->nr_running never equaled 1 to break out of it. When I
added a trace_printk() to see what that number was, it was 335 and
never decrementing!

Looking at the deadline code I found:

static void __dequeue_task_dl(struct rq *rq, struct task_struct *p, int flags) {
	dequeue_dl_entity(&p->dl);
	dequeue_pushable_dl_task(rq, p);
}

static void dequeue_task_dl(struct rq *rq, struct task_struct *p, int flags) {
	update_curr_dl(rq);
	__dequeue_task_dl(rq, p, flags);

	dec_nr_running(rq);
}

And this:

	if (dl_runtime_exceeded(rq, dl_se)) {
		__dequeue_task_dl(rq, curr, 0);
		if (likely(start_dl_timer(dl_se, curr->dl.dl_boosted)))
			dl_se->dl_throttled = 1;
		else
			enqueue_task_dl(rq, curr, ENQUEUE_REPLENISH);

		if (!is_leftmost(curr, &rq->dl))
			resched_task(curr);
	}

Notice how we call __dequeue_task_dl() and in the else case we
call enqueue_task_dl()? Also notice that dequeue_task_dl() has
underscores where enqueue_task_dl() does not. The enqueue_task_dl()
calls inc_nr_running(rq), but __dequeue_task_dl() does not. This is
where we get nr_running out of sync.

[snip]

Another point where nr_running can get out of sync is when the dl_timer
fires:

	dl_se->dl_throttled = 0;
	if (p->on_rq) {
		enqueue_task_dl(rq, p, ENQUEUE_REPLENISH);
		if (task_has_dl_policy(rq->curr))
			check_preempt_curr_dl(rq, p, 0);
		else
			resched_task(rq->curr);

This patch does two things:

 - correctly accounts for throttled tasks (that are now considered
   !running);

 - fixes the bug, updating nr_running from {inc,dec}_dl_tasks(),
   since we risk to update it twice in some situations (e.g., a
   task is dequeued while it has exceeded its budget).

Cc: mingo@redhat.com
Cc: torvalds@linux-foundation.org
Cc: akpm@linux-foundation.org
Reported-by: Steven Rostedt <rostedt@goodmis.org>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Tested-by: Steven Rostedt <rostedt@goodmis.org>
Signed-off-by: Juri Lelli <juri.lelli@gmail.com>
Signed-off-by: Peter Zijlstra <peterz@infradead.org>
Link: http://lkml.kernel.org/r/1392884379-13744-1-git-send-email-juri.lelli@gmail.comSigned-off-by: Thomas Gleixner <tglx@linutronix.de>

Pull PCI updates from Bjorn Helgaas:
 "The most interesting thing here is the change to enable INTx (by
  clearing PCI_COMMAND_INTX_DISABLE) if the BIOS left INTx disabled.
  Apparently the Baytrail BIOS does this, which means EHCI doesn't work.

  Also, fix an AHCI MSI regression and other issues with the recent MSI
  changes.  This also adds pci_enable_msi_exact() and
  pci_enable_msix_exact(), which aren't regression fixes, but will keep
  us from touching drivers twice (once to stop using the deprecated
  pci_enable_msi(), etc., and again to use the *_exact() variants).

  There's also a minor MVEBU fix.

  Summary:

  MSI:
    - Fix AHCI single-MSI fallback (Alexander Gordeev)
    - Fix populate_msi_sysfs() error paths (Greg Kroah-Hartman)
    - Fix htmldocs problem (Masanari Iida)
    - Add pci_enable_msi_exact() and pci_enable_msix_exact() (Alexander Gordeev)
    - Update documentation (Alexander Gordeev)

  Miscellaneous:
    - mvebu: expose device ID & revision via lspci (Andrew Lunn)
    - Enable INTx if the BIOS left them disabled (Bjorn Helgaas)"

* tag 'pci-v3.14-fixes-1' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
  ahci: Fix broken fallback to single MSI mode
  PCI: Enable INTx if BIOS left them disabled
  PCI/MSI: Add pci_enable_msi_exact() and pci_enable_msix_exact()
  PCI/MSI: Fix cut-and-paste errors in documentation
  PCI/MSI: Add pci_enable_msi() documentation back
  PCI/MSI: Fix pci_msix_vec_count() htmldocs failure
  PCI/MSI: Fix leak of msi_attrs
  PCI/MSI: Check kmalloc() return value, fix leak of name
  PCI: mvebu: Use Device ID and revision from underlying endpoint

Pull libata fixes from Tejun Heo:
 "Various device specific fixes.  Nothing too interesting"

* 'for-3.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
  ahci: disable NCQ on Samsung pci-e SSDs on macbooks
  ata: sata_mv: Cleanup only the initialized ports
  sata_sil: apply MOD15WRITE quirk to TOSHIBA MK2561GSYN
  ata: enable quirk from jmicron JMB350 for JMB394
  ATA: SATA_MV: Add missing Kconfig select statememnt
  ata: pata_imx: Check the return value from clk_prepare_enable()

Pull cgroup fixes from Tejun Heo:
 "Quite a few fixes this time.

  Three locking fixes, all marked for -stable.  A couple error path
  fixes and some misc fixes.  Hugh found a bug in memcg offlining
  sequence and we thought we could fix that from cgroup core side but
  that turned out to be insufficient and got reverted.  A different fix
  has been applied to -mm"

* 'for-3.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/cgroup:
  cgroup: update cgroup_enable_task_cg_lists() to grab siglock
  Revert "cgroup: use an ordered workqueue for cgroup destruction"
  cgroup: protect modifications to cgroup_idr with cgroup_mutex
  cgroup: fix locking in cgroup_cfts_commit()
  cgroup: fix error return from cgroup_create()
  cgroup: fix error return value in cgroup_mount()
  cgroup: use an ordered workqueue for cgroup destruction
  nfs: include xattr.h from fs/nfs/nfs3proc.c
  cpuset: update MAINTAINERS entry
  arm, pm, vmpressure: add missing slab.h includes

Pull workqueue fixes from Tejun Heo:
 "Two workqueue fixes.  One for an unlikely but possible critical bug
  during kworker shutdown and the other to make lockdep names a bit more
  descriptive"

* 'for-3.14-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/wq:
  workqueue: ensure @task is valid across kthread_stop()
  workqueue: add args to workqueue lockdep name

Pull DMA-mapping fixes from Marek Szyprowski:
 "This contains fixes for incorrect atomic test in dma-mapping subsystem
  for ARM and x86 architecture"

* 'fixes-for-v3.14' of git://git.linaro.org/people/mszyprowski/linux-dma-mapping:
  x86: dma-mapping: fix GFP_ATOMIC macro usage
  ARM: dma-mapping: fix GFP_ATOMIC macro usage

Signed-off-by: Brian Campbell <brian.campbell@editshare.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull NFS client bugfixes from Trond Myklebust:
 "Highlights include stable fixes for the following bugs:

   - General performance regression due to NFS_INO_INVALID_LABEL being
     set when the server doesn't support labeled NFS
   - Hang in the RPC code due to a socket out-of-buffer race
   - Infinite loop when trying to establish the NFSv4 lease
   - Use-after-free bug in the RPCSEC gss code.
   - nfs4_select_rw_stateid is returning with a non-zero error value on
     success

  Other bug fixes:

  - Potential memory scribble in the RPC bi-directional RPC code
  - Pipe version reference leak
  - Use the correct net namespace in the new NFSv4 migration code"

* tag 'nfs-for-3.14-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  NFS fix error return in nfs4_select_rw_stateid
  NFSv4: Use the correct net namespace in nfs4_update_server
  SUNRPC: Fix a pipe_version reference leak
  SUNRPC: Ensure that gss_auth isn't freed before its upcall messages
  SUNRPC: Fix potential memory scribble in xprt_free_bc_request()
  SUNRPC: Fix races in xs_nospace()
  SUNRPC: Don't create a gss auth cache unless rpc.gssd is running
  NFS: Do not set NFS_INO_INVALID_LABEL unless server supports labeled NFS

Pull MFD fixes from Lee Jones:
 "Couple of small issues solved:
   - Suspend/Resume call-backs require CONFIG_PM_SLEEP
   - Some drivers written for 32bit architectures fail when compiled
     with a 64bit compiler.  The fixes will future proof the drivers"

* tag 'mfd-fixes-3.14-1' of git://git.linaro.org/people/lee.jones/mfd:
  mfd: sec-core: sec_pmic_{suspend,resume}() should depend on CONFIG_PM_SLEEP
  mfd: max14577: max14577_{suspend,resume}() should depend on CONFIG_PM_SLEEP
  mfd: tps65217: Naturalise cross-architecture discrepancies
  mfd: wm8994-core: Naturalise cross-architecture discrepancies
  mfd: max8998: Naturalise cross-architecture discrepancies
  mfd: max8997: Naturalise cross-architecture discrepancies

Do not return an error when nfs4_copy_delegation_stateid succeeds.
Signed-off-by: Andy Adamson <andros@netapp.com>
Link: http://lkml.kernel.org/r/1392737765-41942-1-git-send-email-andros@netapp.com
Fixes: ef1820f9 (NFSv4: Don't try to recover NFSv4 locks when...)
Cc: NeilBrown <neilb@suse.de>
Cc: stable@vger.kernel.org # 3.12+
Signed-off-by: Trond Myklebust <trond.myklebust@primarydata.com>

If CONFIG_PM_SLEEP=n:

drivers/mfd/sec-core.c:349: warning: ‘sec_pmic_suspend’ defined but not used
drivers/mfd/sec-core.c:371: warning: ‘sec_pmic_resume’ defined but not used
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

If CONFIG_PM_SLEEP=n:

drivers/mfd/max14577.c:177: warning: ‘max14577_suspend’ defined but not used
drivers/mfd/max14577.c:200: warning: ‘max14577_resume’ defined but not used
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>

If we compile the TPS65217 for a 64bit architecture we receive the following
warnings:

drivers/mfd/tps65217.c: In function ‘tps65217_probe’:
drivers/mfd/tps65217.c:173:13:
  warning: cast from pointer to integer of different size
   chip_id = (unsigned int)match->data;
             ^
Signed-off-by: Lee Jones <lee.jones@linaro.org>

If we compile the WM8994 for a 64bit architecture we receive the following
warnings:

drivers/mfd/wm8994-core.c: In function ‘wm8994_i2c_probe’:
drivers/mfd/wm8994-core.c:639:19:
  warning: cast from pointer to integer of different size
    wm8994->type = (int)of_id->data;
                   ^
Signed-off-by: Lee Jones <lee.jones@linaro.org>

If we compile the MAX8998 for a 64bit architecture we receive the following
warnings:

  drivers/mfd/max8998.c: In function ‘max8998_i2c_get_driver_data’:
  drivers/mfd/max8998.c:178:10:
    warning: cast from pointer to integer of different size
     return (int)match->data;
            ^
Signed-off-by: Lee Jones <lee.jones@linaro.org>

If we compile the MAX8997 for a 64bit architecture we receive the following
warnings:

  drivers/mfd/max8997.c: In function ‘max8997_i2c_get_driver_data’:
  drivers/mfd/max8997.c:173:10:
    warning: cast from pointer to integer of different size
     return (int)match->data;
            ^
Signed-off-by: Lee Jones <lee.jones@linaro.org>

Pull drm fixes from Dave Airlie:
 "Lots of little small things, nothing too major: nouveau regression
  fixes, vmware fixes for the new hw support, memory leaks in error path
  fixes"

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux: (31 commits)
  drm/radeon/ni: fix typo in dpm sq ramping setup
  drm/radeon/si: fix typo in dpm sq ramping setup
  drm/radeon: fix CP semaphores on CIK
  drm/radeon: delete a stray tab
  drm/radeon: fix display tiling setup on SI
  drm/radeon/dpm: reduce r7xx vblank mclk threshold to 200
  drm/radeon: fill in DRM_CAPs for cursor size
  drm: add DRM_CAPs for cursor size
  drm/radeon: unify bpc handling
  drm/ttm: Fix memory leak in ttm_agp_backend.c
  drm/ttm: declare 'struct device' in ttm_page_alloc.h
  drm/nouveau: fix TTM_PL_TT memtype on pre-nv50
  drm/nv50/disp: use correct register to determine DP display bpp
  drm/nouveau/fb: use correct ram oclass for nv1a hardware
  drm/nv50/gr: add missing nv_error parameter priv
  drm/nouveau: fix ENG_RUNLIST register address
  drm/nv4c/bios: disallow retrieving from prom on nv4x igp's
  drm/nv4c/vga: decode register is in a different place on nv4x igp's
  drm/nv4c/mc: nv4x igp's have a different msi rearm register
  drm/nouveau: set irq_enabled manually
  ...

Pull HID update from Jiri Kosina:

 - fixes for several bugs in incorrect allocations of buffers by David
   Herrmann and Benjamin Tissoires.

 - support for a few new device IDs by Archana Patni, Benjamin
   Tissoires, Huei-Horng Yo, Reyad Attiyat and Yufeng Shen

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/hid:
  HID: hyperv: make sure input buffer is big enough
  HID: Bluetooth: hidp: make sure input buffers are big enough
  HID: hid-sensor-hub: quirk for STM Sensor hub
  HID: apple: add Apple wireless keyboard 2011 JIS model support
  HID: fix buffer allocations
  HID: multitouch: add FocalTech FTxxxx support
  HID: microsoft: Add ID's for Surface Type/Touch Cover 2
  HID: usbhid: quirk for CY-TM75 75 inch Touch Overlay

Pull networking fixes from David Miller:

 1) kvaser CAN driver has fixed limits of some of it's table, validate
    that we won't exceed those limits at probe time.  Fix from Olivier
    Sobrie.

 2) Fix rtl8192ce disabling interrupts for too long, from Olivier
    Langlois.

 3) Fix botched shift in ath5k driver, from Dan Carpenter.

 4) Fix corruption of deferred packets in TIPC, from Erik Hugne.

 5) Fix newlink error path in macvlan driver, from Cong Wang.

 6) Fix netpoll deadlock in bonding, from Ding Tianhong.

 7) Handle GSO packets properly in forwarding path when fragmentation is
    necessary on egress, from Florian Westphal.

 8) Fix axienet build errors, from Michal Simek.

 9) Fix refcounting of ubufs on tx in vhost net driver, from Michael S
    Tsirkin.

10) Carrier status isn't set properly in hyperv driver, from Haiyang
    Zhang.

11) Missing pci_disable_device() in tulip_remove_one), from Ingo Molnar.

12) AF_PACKET qdisc bypass mode doesn't adhere to driver provided TX
    queue selection method.  Add a fallback method mechanism to fix this
    bug, from Daniel Borkmann.

13) Fix regression in link local route handling on GRE tunnels, from
    Nicolas Dichtel.

14) Bonding can assign dup aggregator IDs in some sequences of
    configuration, fix by making the allocation counter per-bond instead
    of global.  From Jiri Bohac.

15) sctp_connectx() needs compat translations, from Daniel Borkmann.

16) Fix of_mdio PHY interrupt parsing, from Ben Dooks

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (62 commits)
  MAINTAINERS: add entry for the PHY library
  of_mdio: fix phy interrupt passing
  net: ethernet: update dependency and help text of mvneta
  NET: fec: only enable napi if we are successful
  af_packet: remove a stray tab in packet_set_ring()
  net: sctp: fix sctp_connectx abi for ia32 emulation/compat mode
  ipv4: fix counter in_slow_tot
  irtty-sir.c: Do not set_termios() on irtty_close()
  bonding: 802.3ad: make aggregator_identifier bond-private
  usbnet: remove generic hard_header_len check
  gre: add link local route when local addr is any
  batman-adv: fix potential kernel paging error for unicast transmissions
  batman-adv: avoid double free when orig_node initialization fails
  batman-adv: free skb on TVLV parsing success
  batman-adv: fix TT CRC computation by ensuring byte order
  batman-adv: fix potential orig_node reference leak
  batman-adv: avoid potential race condition when adding a new neighbour
  batman-adv: properly check pskb_may_pull return value
  batman-adv: release vlan object after checking the CRC
  batman-adv: fix TT-TVLV parsing on OGM reception
  ...

Pull ARM fixes from Russell King:
 "A range of ARM fixes.  Biggest change is the stage-2 attributes used
  for for hyp mode which were wrong.  I've killed some bits in a couple
  of DT files which turned out not to be required, and a few other
  fixes.

  One fix touches code outside of arch/arm, which is related to sorting
  out the DMA masks correctly.  There is a long standing issue with the
  conversion from PFNs to addresses where people assume that shifting an
  unsigned long left by PAGE_SHIFT results in a correct address.  This
  is not the case with C: the integer promotion happens at assignment
  after evaluation.  This fixes the recently introduced dma_max_pfn()
  function, but there's a number of other places where we try this
  directly on an unsigned long in the mm code"

* 'fixes' of git://ftp.arm.linux.org.uk/~rmk/linux-arm:
  ARM: 7957/1: add DSB after icache flush in __flush_icache_all()
  Fix uses of dma_max_pfn() when converting to a limiting address
  ARM: 7955/1: spinlock: ensure we have a compiler barrier before sev
  ARM: 7953/1: mm: ensure TLB invalidation is complete before enabling MMU
  ARM: 7952/1: mm: Fix the memblock allocation for LPAE machines
  ARM: 7950/1: mm: Fix stage-2 device memory attributes
  ARM: dts: fix spdif pinmux configuration

Pull jfs fix from David Kleikamp:
 "Another ACL regression. This one more subtle"

* tag 'jfs-3.14-rc4' of git://github.com/kleikamp/linux-shaggy:
  jfs: set i_ctime when setting ACL

Currently, there's nothing preventing cgroup_enable_task_cg_lists()
from missing set PF_EXITING and race against cgroup_exit().  Depending
on the timing, cgroup_exit() may finish with the task still linked on
css_set leading to list corruption.  Fix it by grabbing siglock in
cgroup_enable_task_cg_lists() so that PF_EXITING is guaranteed to be
visible.

This whole on-demand cg_list optimization is extremely fragile and has
ample possibility to lead to bugs which can cause things like
once-a-year oops during boot.  I'm wondering whether the better
approach would be just adding "cgroup_disable=all" handling which
disables the whole cgroup rather than tempting fate with this
on-demand craziness.
Signed-off-by: Tejun Heo <tj@kernel.org>
Acked-by: Li Zefan <lizefan@huawei.com>
Cc: stable@vger.kernel.org

The PHY library has been subject to some changes, new drivers and DT
interactions over the past few months. Add myself as a maintainer for
the core PHY library parts and drivers. Make sure the PHY library entry
also covers the Device Tree files which have a close interaction with
the MDIO bus, PHY connection and Ethernet PHY mode parsing.

CC: Grant Likely <grant.likely@linaro.org>
CC: Shaohui Xie <shaohui.xie@freescale.com>
CC: Andy Fleming <afleming@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The of_mdiobus_register_phy() is not setting phy->irq thus causing
some drivers to incorrectly assume that the PHY does not have an
IRQ associated with it. Not only do some drivers report no IRQ
they do not install an interrupt handler for the PHY.

Simplify the code setting irq and set the phy->irq at the same
time so that we cover the following issues, which should cover
all the cases the code will find:

- Set phy->irq if node has irq property and mdio->irq is NULL
- Set phy->irq if node has no irq and mdio->irq is not NULL
- Leave phy->irq as PHY_POLL default if none of the above

This fixes the issue:
 net eth0: attached PHY 1 (IRQ -1) to driver Micrel KSZ8041RNLI

to the correct:
 net eth0: attached PHY 1 (IRQ 416) to driver Micrel KSZ8041RNLI
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

With the introduction of the support for Armada 375 and Armada 38x,
the hidden Kconfig option MACH_ARMADA_370_XP is being renamed to
MACH_MVEBU_V7. Therefore, the dependency that was used for the mvneta
driver can no longer work. This commit replaces this dependency by a
dependency on PLAT_ORION, which is used similarly for the mv643xx_eth
driver.

In addition to this, it takes this opportunity to adjust the
description and help text to indicate that the driver can is also used
for Armada 38x. Note that Armada 375 cannot use this driver as it has
a completely different networking unit, which will require a separate
driver.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Acked-by: Jason Cooper <jason@lakedaemon.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

If napi is left enabled after a failed attempt to bring the interface
up, we BUG:

fec 2188000.ethernet eth0: no PHY, assuming direct connection to switch
libphy: PHY fixed-0:00 not found
fec 2188000.ethernet eth0: could not attach to PHY
------------[ cut here ]------------
kernel BUG at include/linux/netdevice.h:502!
Internal error: Oops - BUG: 0 [#1] SMP ARM
...
PC is at fec_enet_open+0x4d0/0x500
LR is at __dev_open+0xa4/0xfc

Only enable napi after we are past all the failure paths.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>

At first glance it looks like there is a missing curly brace but
actually the code works the same either way.  I have adjusted the
indenting but left the code the same.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Daniel Borkmann <dborkman@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull request of 2014-02-18

One compile fix and one memory leak.

* tag 'ttm-fixes-3.14-2014-02-18' of git://people.freedesktop.org/~thomash/linux:
  drm/ttm: Fix memory leak in ttm_agp_backend.c
  drm/ttm: declare 'struct device' in ttm_page_alloc.h

Merge tag 'vmwgfx-fixes-3.14-2014-02-18' of git://people.freedesktop.org/~thomash/linux into drm-fixes

Pull request of 2014-02-18.

Nothing special. The biggest change is adding a couple of command defines and
packing the command data correctly.

* tag 'vmwgfx-fixes-3.14-2014-02-18' of git://people.freedesktop.org/~thomash/linux:
  drm/vmwgfx: Fix command defines and checks
  drm/vmwgfx: Fix possible integer overflow
  drm/vmwgfx: Remove stray const
  drm/vmwgfx: unlock on error path in vmw_execbuf_process()
  drm/vmwgfx: Get maximum mob size from register SVGA_REG_MOB_MAX_SIZE
  drm/vmwgfx: Fix a couple of sparse warnings and errors

Fix for 128x128 cursors, along with some misc fixes.

* 'drm-fixes-3.14' of git://people.freedesktop.org/~agd5f/linux:
  drm/radeon/ni: fix typo in dpm sq ramping setup
  drm/radeon/si: fix typo in dpm sq ramping setup
  drm/radeon: fix CP semaphores on CIK
  drm/radeon: delete a stray tab
  drm/radeon: fix display tiling setup on SI
  drm/radeon/dpm: reduce r7xx vblank mclk threshold to 200
  drm/radeon: fill in DRM_CAPs for cursor size
  drm: add DRM_CAPs for cursor size
  drm/radeon: unify bpc handling

John W. Linville says:

====================
Please pull this batch of fixes intended for the 3.14 stream...

For the iwlwifi one, Emmanuel says:

"As explicitly written in the commit message, we prefer to disable Tx
AMPDU on NICs supported by iwldvm. This feature gives a big boost in
Tx performance, but the firmware is buggy and we can't rely on it.
Our hope is that most of the users out there want wifi to surf on
the web which means that they care more for Rx traffic than for Tx.
People who want to enable it can do so with the help of a module
parameter."

On top of that...

Dan Carpenter fixes a typo/thinko in ath5k.

Olivier Langlois fixes a couple of rtlwifi issues, one which leaves
IRQs disabled too long (causing a variety of problems elsewhere),
and one which fixes an incorrect return code when failing to enable
the NIC.

Russell King fixes a NULL pointer dereference in hostap.

Stanislaw Gruszka fixes a DMA coherence issue in the rtl8187 driver.

Please let me know if there are problems!
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

When a kworker should die, the kworkre is notified through WORKER_DIE
flag instead of kthread_should_stop().  This, IIRC, is primarily to
keep the test synchronized inside worker_pool lock.  WORKER_DIE is
first set while holding pool->lock, the lock is dropped and
kthread_stop() is called.

Unfortunately, this means that there's a slight chance that the target
kworker may see WORKER_DIE before kthread_stop() finishes and exits
and frees the target task before or during kthread_stop().

Fix it by pinning the target task before setting WORKER_DIE and
putting it after kthread_stop() is done.

tj: Improved patch description and comment.  Moved pinning above
    WORKER_DIE for better signify what it's protecting.

CC: stable@vger.kernel.org
Signed-off-by: Lai Jiangshan <laijs@cn.fujitsu.com>
Signed-off-by: Tejun Heo <tj@kernel.org>

SCTP's sctp_connectx() abi breaks for 64bit kernels compiled with 32bit
emulation (e.g. ia32 emulation or x86_x32). Due to internal usage of
'struct sctp_getaddrs_old' which includes a struct sockaddr pointer,
sizeof(param) check will always fail in kernel as the structure in
64bit kernel space is 4bytes larger than for user binaries compiled
in 32bit mode. Thus, applications making use of sctp_connectx() won't
be able to run under such circumstances.

Introduce a compat interface in the kernel to deal with such
situations by using a 'struct compat_sctp_getaddrs_old' structure
where user data is copied into it, and then sucessively transformed
into a 'struct sctp_getaddrs_old' structure with the help of
compat_ptr(). That fixes sctp_connectx() abi without any changes
needed in user space, and lets the SCTP test suite pass when compiled
in 32bit and run on 64bit kernels.

Fixes: f9c67811 ("sctp: Fix regression introduced by new sctp_connectx api")
Signed-off-by: Daniel Borkmann <dborkman@redhat.com>
Acked-by: Neil Horman <nhorman@tuxdriver.com>
Acked-by: Vlad Yasevich <vyasevich@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>