- 21 Sep, 2020 1 commit
-
-
Daniel Vetter authored
Just some prep work before we rework the lifetime handling, which requires replacing all the drm_dev_put in selftests by something else. v2: Don't go with a static inline, upsets the header tests and separation. Acked-by:
Rodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by:
Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Signed-off-by:
Daniel Vetter <daniel.vetter@intel.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200918132505.2316382-2-daniel.vetter@ffwll.ch
-
- 18 Sep, 2020 2 commits
-
-
Jing Xiangfeng authored
Remove the superfluous break, as there is a 'return' before it. Fixes: bad07ff7 ("fbcon: smart blitter usage for scrolling") Signed-off-by:
Jing Xiangfeng <jingxiangfeng@huawei.com> Reviewed-by:
Nick Desaulniers <ndesaulniers@google.com> Reviewed-by:
Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20200918010521.69950-1-jingxiangfeng@huawei.com
-
Vaibhav Gupta authored
The changes made in below mentioned commit removed CONFIG_PM containers from drivers/video/fbdev/aty/atyfb_base.c but not from drivers/video/fbdev/aty/atyfb.h for respective callbacks. This resulted in error for implicit declaration for those callbacks. Fixes: 348b2956 ("fbdev: aty: use generic power management") Signed-off-by:
Vaibhav Gupta <vaibhavgupta40@gmail.com> Reported-by:
kernel test robot <lkp@intel.com> Signed-off-by:
-
- 17 Sep, 2020 14 commits
-
-
Dave Airlie authored
This was unused. Signed-off-by:
Dave Airlie <airlied@redhat.com> Reviewed-by:
Christian König <christian.koenig@amd.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200917064132.148521-3-airlied@gmail.com
-
Dave Airlie authored
The two accel cleanup paths were mostly the same once refactored. Just pass a bool to say if the evictions are to be pipelined. Signed-off-by:
-
Dave Airlie authored
The pipeline and accel cleansups has similiar paths here. Signed-off-by:
-
Dave Airlie authored
Both accel cleanup and pipeline move had the same code, make a single function for it. Signed-off-by:
-
Dave Airlie authored
This pattern is called in a few places, just clean it up. Reviewed-by:
-
Dave Airlie authored
Now the bind functions have all the protection explicitly the drivers can just call them directly, and the api can be unexported Reviewed-by:
-
Dave Airlie authored
This moves unbind into the driver side on destroy paths. Reviewed-by:
-
Dave Airlie authored
Call the driver first and have it call the common code cleanup. This is useful later to fix unbind. Reviewed-by:
-
Dave Airlie authored
This moves the generic tracking into the drivers and protects against reentrancy in the drivers. It fixes up radeon and agp to be able to query the bound status as that is required. Reviewed-by:
-
Christian König authored
Extern is the default attribute for functions anyway. Signed-off-by:
-
Daniel Vetter authored
GPU drivers need this in their shrinkers, to be able to throw out mmap'ed buffers. Note that we also need dma_resv_lock in shrinkers, but that loop is resolved by trylocking in shrinkers. So full hierarchy is now (ignore some of the other branches we already have primed): mmap_read_lock -> dma_resv -> shrinkers -> i_mmap_lock_write I hope that's not inconsistent with anything mm or fs does, adding relevant people. Reviewed-by:
Thomas Hellström <thomas.hellstrom@intel.com> Reviewed-by:
-
Wang Qing authored
Change the comment typo: "manger" -> "manager". Signed-off-by:
Wang Qing <wangqing@vivo.com> Signed-off-by:
-
Lukas Bulwahn authored
Commit f15a3ea8 ("MAINTAINERS: Add ASPEED BMC GFX DRM driver entry") does not mention that linux-aspeed@lists.ozlabs.org is moderated for non-subscribers, but the other three entries for linux-aspeed@lists.ozlabs.org do. By 'majority vote' among entries, let us assume it was just missed here and adjust it to be consistent with others. Signed-off-by:
Lukas Bulwahn <lukas.bulwahn@gmail.com> Signed-off-by:
-
Christian König authored
Unexport ttm_check_under_lowerlimit. Make ttm_bo_acc_size static and unexport it. Remove ttm_get_kernel_zone_memory_size. Signed-off-by:
-
- 16 Sep, 2020 8 commits
-
-
Maxime Ripard authored
Merge branch 'virtio-shm' of git://git.kernel.org/pub/scm/linux/kernel/git/mszeredi/fuse into drm-misc-next Topic pull request for core virtio changes that will be required by the DRM driver. Signed-off-by:
Maxime Ripard <maxime@cerno.tech> From: Gurchetan Singh <gurchetansingh@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/CAAfnVBn2BzXWFY3hhjDxd5q0P2_JWn-HdkVxgS94x9keAUZiow@mail.gmail.com
-
Thomas Zimmermann authored
An active cursor plane requires a valid display mode. Change the commit_tail callback, so that it sets up the CRTC's mode before updating planes. Signed-off-by:
Thomas Zimmermann <tzimmermann@suse.de> Acked-by:
-
Thomas Zimmermann authored
This change simplifies ast's modesetting code. The display mode is now programmed from within the CRTC's atomic_enable(), which only runs if we actually want to program the mode. Corresponding code in atomic_flush() is being removed. Also removed is atomic_begin(), which serves no purpose at all. Signed-off-by:
-
Thomas Zimmermann authored
The ast HW cursor requires the primary plane and CRTC to display at a valid mode and format. This is not the case while switching display modes, which can lead to the screen turing permanently dark. As a workaround, the ast driver now disables active planes while the mode or format switch takes place. It also synchronizes with the vertical refresh to give CRTC and planes some time to catch up on each other. The active planes planes (primary or cursor) will be re-enabled by each plane's atomic_update() function. v3: * move the logic into the CRTC's atomic_disable function v2: * move the logic into the commit-tail function Signed-off-by:
-
Thomas Zimmermann authored
The atomic modesetting code tried to distinguish format changes from full modesetting operations. But the implementation was buggy and the format registers were often updated even for simple pageflips. Fix this problem by handling format changes in the primary plane's update function. v3: * program format in primary plane's update function Signed-off-by:
-
Thomas Zimmermann authored
I'm adding myself as reviewer for ast, mgag200 and udl. I've already been keeping these drivers in shape for a while. While at it I'm also setting the list and tree for ast and mgag200, and update each driver's status to Supported. Working on these drivers is part of my job. Signed-off-by:
-
Stefan Agner authored
The lcdif IP does not support a framebuffer pitch (stride) other than framebuffer width. Check for equality and reject the framebuffer otherwise. This prevents a distorted picture when using 640x800 and running the Mesa graphics stack. Mesa tries to use a cache aligned stride, which leads at that particular resolution to width != stride. Currently Mesa has no fallback behavior, but rejecting this configuration allows userspace to handle the issue correctly. Fixes: 45d59d70 ("drm: Add new driver for MXSFB controller") Signed-off-by:
Stefan Agner <stefan@agner.ch> Reviewed-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Link: https://patchwork.freedesktop.org/patch/msgid/20200908141654.266836-1-stefan@agner.ch
-
Tian Tao authored
Handing the return value of drm_universal_plane_init to fix the following W=1 kernel build warning(s): vc4_plane.c: In function ‘vc4_plane_init’: vc4_plane.c:1340:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable] Signed-off-by:
Tian Tao <tiantao6@hisilicon.com> Reviewed-by:
-
- 15 Sep, 2020 14 commits
-
-
Dave Airlie authored
Just use the top bit of page flags to store the populated state. Reviewed-by:
-
Dave Airlie authored
Move bound up into the bo object, and keep populated with the tt object. The ghost object handling needs to follow the flags at the bo level now instead of it being part of the ttm tt object. Reviewed-by:
-
Dave Airlie authored
Move these up to the bo level, moving ttm_tt to just being backing store. Next step is to move the bound flag out. Reviewed-by:
-
Dave Airlie authored
Drivers have to call populate themselves now before binding. Reviewed-by:
-
Dave Airlie authored
This just makes things easier later. Reviewed-by:
-
Dave Airlie authored
All places this was called was using bo->ttm either direct or indirectly. v2: move to ttm_bo Reviewed-by:
-
Dave Airlie authored
This adds 2 getters and 4 setters, however unbound and populated are currently the same thing, this will change, it also drops a BUG_ON that seems not that useful. Reviewed-by:
-
Christian König authored
Instead of letting TTM make an educated guess based on some mask all drivers should just specify what caching they want for their CPU mappings. Signed-off-by:
-
Christian König authored
Instead of letting TTM masking the caching bits specify directly what the driver needs. Signed-off-by:
-
Christian König authored
As far as I can tell this was never used either and we just always fallback to the order cached > wc > uncached anyway. Signed-off-by:
-
Enric Balletbo i Serra authored
The get_edid() callback can be triggered anytime by an ioctl, i.e drm_mode_getconnector (ioctl) -> drm_helper_probe_single_connector_modes -> drm_bridge_connector_get_modes -> ps8640_bridge_get_edid Actually if the bridge pre_enable() function was not called before get_edid(), the driver will not be able to get the EDID properly and display will not work until a second get_edid() call is issued and if pre_enable() is called before. The side effect of this, for example, is that you see anything when `Frecon` starts, neither the splash screen, until the graphical session manager starts. To fix this we need to make sure that all we need is enabled before reading the EDID. This means the following: 1. If get_edid() is called before having the device powered we need to power on the device. In such case, the driver will power off again the device. 2. If get_edid() is called after having the device powered, all should just work. We added a powered flag in order to avoid recurrent calls to ps8640_bridge_poweron() and unneeded delays. 3. This seems to be specific for this device, but we need to make sure the panel is powered on before do a power on cycle on this device. Otherwise the device fails to retrieve the EDID. Signed-off-by:Enric Balletbo i Serra <enric.balletbo@collabora.com> Tested-by:
Bilal Wasim <bwasim.lkml@gmail.com> Acked-by:
Neil Armstrong <narmstrong@baylibre.com> Signed-off-by:
-
Gerd Hoffmann authored
Usually we wait for the host to complete the unref request, then cleanup the guest-side state of the object in the completion callback. When submitting the unref command failed the completion callback will not be called though, so cleanup right away. Fixes a WARN on stale mm entries on driver shutdown. Signed-off-by:
Gerd Hoffmann <kraxel@redhat.com> Reviewed-by:
Gurchetan Singh <gurchetansingh@chromium.org> Link: http://patchwork.freedesktop.org/patch/msgid/20200908070723.6394-4-kraxel@redhat.com
-
Gerd Hoffmann authored
In case queuing virtio commands fails (can happen when the device got unplugged) pass up the error. Signed-off-by:
-
Gerd Hoffmann authored
Use managed init call to simplify cleanup. Signed-off-by:
-
- 14 Sep, 2020 1 commit
-
-
Paul Cercueil authored
Ingenic SoCs are most notably used in cheap chinese handheld gaming consoles. There, the games and applications generally render in software directly into GEM buffers. Traditionally, GEM buffers are mapped write-combine. Writes to the buffer are accelerated, and reads are slow. Application doing lots of alpha-blending paint inside shadow buffers, which is then memcpy'd into the final GEM buffer. On recent Ingenic SoCs however, it is much faster to have a fully cached GEM buffer, in which applications paint directly, and whose data is invalidated before scanout, than having a write-combine GEM buffer, even when alpha blending is not used. Add an optional 'cached_gem_buffers' parameter to the ingenic-drm driver to allow GEM buffers to be mapped fully-cached, in order to speed up software rendering. v2: Use standard noncoherent DMA APIs v3: Use damage clips instead of invalidating full frames v4: Avoid dma_pgprot() which is not exported. Using vm_get_page_prot() is enough in this case. v5: - Avoid calling drm_gem_cma_prime_mmap(). It has the side effect that an extra object reference is obtained, which causes our dumb buffers to never be freed. It should have been drm_gem_cma_mmap_obj(). However, our custom mmap function only differs with one flag, so we can cleanly handle both modes in ingenic_drm_gem_mmap(). - Call drm_gem_vm_close() if drm_mmap_attrs() failed, just like in drm_gem_cma_mmap_obj(). Signed-off-by:Paul Cercueil <paul@crapouillou.net> Acked-by:
Sam Ravnborg <sam@ravnborg.org> Link: https://patchwork.freedesktop.org/patch/msgid/20200912195639.176001-1-paul@crapouillou.net
-
