Hi:

skbuff: Move new __skb_clone code into __copy_skb_header

It seems that people just keep on adding stuff to __skb_clone
instead __copy_skb_header.  This is wrong as it means your brand-new
attributes won't always get copied as you intended.

This patch moves them to the right place, and adds a comment to
prevent this from happening again.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>

Thanks,
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for netdev->vlan_features in the myri10ge driver.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Drop the myri10ge_lro module parameter now that we have ethtool
to enable/disable LRO in the myri10ge driver.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the way we check whether lro_flush_all should be called
in the myri10ge driver.
Signed-off-by: Brice Goglin <brice@myri.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In case of allocation failure, the actual ring size is rounded down to
nearest power of 2. The remaining descriptors are freed.
The CQ and SRQ are allocated with the actual size and the mask is updated.
Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Yevgeny Petrilin <yevgenyp@mellanox.co.il>
Signed-off-by: David S. Miller <davem@davemloft.net>

when display channel info in debugfs, always check for valid band
before access the pointer and display information

for 1000 NIC, it only support "bgn" mode, so there is no 5.2GHz channels
available to display.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Enable using iwlwifi driver in AMT system.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

rb value should be 0x10 for devices using ICT.
 RX interrupt was not performing well with
 0 value
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Periodic RX interrupt needed with ICT interrupt to prevent RX race.
Sending RX interrupt require many steps to be done in the
the device:
 1- write interrupt to current index in ICT table.
 2- dma RX frame.
 3- update RX shared data to indicate last write index.
 4- send interrupt.
This could lead to RX race, driver could receive RX interrupt
but the shared data changes does not reflect that.
this could lead to RX race, RX periodic will solve this race
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If RX queue becomes empty then we need to restock the queue from tasklet to prevent
ucode from starving. A caller to iwl_rx_allocate will decide if allocated buffer should
come from GFP_ATOMIC or GFP_KERNEL.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add ICT interrupt handler support, ICT should improve CPU utilization
 since it does not require target read which is very expensive. This
 interrupt handler only added to 5000 cards and newer. Device will write
 interrupts to ICT shared table to inform driver about its interrupts.

These patches will not touch 3945 and 4965 interrupt handlers and tasklet.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Fix the bug when using 11n "pure 40MHz" mode cause uCode
crashing by adding support for "pure 40MHz" in RX_ON command flag.
the "mode" field (bits 25:26) has value of 0-3
    0 = 20 MHz only
    1 = 40MHz only
    2 = Mixed
    3 = Reserved
Control Channel ID (bit 22) is valid only in Mixed mode.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

If transmit in HT rate, report the rate index as an MCS rate number
instead of an index. so "iw" can display correct BitRate
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add new lock to be used when accessing some registers. Also move
    the register lock and iwl_grab_nic_access inside the function for register access. This
    will prevent from forgetting to hold locks and nic access in the right way and make code
    easier to maintain.

    We over use the priv->lock spin lock and I guess we need to add new
    one for Tx queue after that we might need to change most of these lock to
    BH and just keep priv->lock as irq type.
Signed-off-by: Mohamed Abbas <mohamed.abbas@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Two type of NVM available for devices 1000, 6000 and after, adding
support to read OTP lower blocks if OTP is used instead of EEPROM.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

IEEE80211_CONF_CHANGE_BEACON_INTERVAL was deprecated a month ago,
it is about time to remove all usage from the rt2x00 drivers and
use the correct beacon interval configuration through the bss_info
structure.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The USB ID with unknown manufacturer is apparently sweex,
copy it to the correct location of the list and add 2
additional USB ID's also belonging to Sweex.
Signed-off-by: Ivo van Doorn <IvDoorn@gmail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

set_infra_mode() tried to restore wpa keys using add_wep_key(). This never
worked so prevent driver from trying.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Split add_wpa_key() from rndis_iw_set_encode_ext so that conversion to cfg80211
would be easier later on.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Driver uses some unnamed bits to control encryption setup. Move these to
enumerations with proper names explaining their meaning.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

BCM4320 doesn't support OID_802_11_TX_POWER_LEVEL (chip implements
the command but setting value has no effect and getting txpower value
always returns 0xff, full power). So remove the code for cleanup.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Old variant of bcm4320 doesn't handle setting configuration parameters
correctly. One symptom is that MAC gets partially overwritten when any
config parameters are set. This patch disables config-params for bcm4320a
(and generic rndis-wlan).
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@mbnet.fi>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The temperature measurement by uCode for 5150 and 5000 are different
        CSR_HW_REV_TYPE_5150: temperature sensor output voltage
        CSR_HW_REV_TYPE_5000: temperature in Celsius
temperature related operation for 5150 is measured by temperature sensor
output voltage; additional conversion is required for set and store
the temperature.

To make sure support different HW design; implement _ops method for
temperature related functions (temperature reading and set ct kill
threshold)
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Add "Greenfield" support for all devices except 4965 and
3945. "Greenfield" is part of 11n features to improve HT performance.
Signed-off-by: Wey-Yi Guy <wey-yi.w.guy@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

'tpt' is a delta throughput (number of packets) and is corelated
to brightness of the LED. We already maintain a delta of packets in
rxtxpackets. There is no need to calculate this delta again which
was affecting the behaviour of LEDS.

Also add two new callback functions for ASSOCIATED/DISASSOCIATED states
where LED's will be *on* for associated state and *off* for disassociated state.

This fixes
http://www.intellinuxwireless.org/bugzilla/show_bug.cgi?id=1771.
Signed-off-by: Abhijeet Kolekar <abhijeet.kolekar@intel.com>
Signed-off-by: Reinette Chatre <reinette.chatre@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The scratch pad register is used to store firmware status after
firmware is downloaded and initialized. After firmware status is
verified OK, the same register is used to store RX packet length.
Hence the firmware status code is no longer valid afterwards.

SD8688 firmware introduces a new register for firmware status
which will never be overwritten.

Also add scratch_reg variable to if_sdio_card structure and
initialize it based on the model of the card during probe.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

This driver supports Intel's full MAC wireless multicomm 802.11 hardware.
Although the hardware is a 802.11agn device, we currently only support
802.11ag, in managed and ad-hoc mode (no AP mode for now).
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The patch moves some utility functions from mac80211 to cfg80211.
Because these functions are doing generic 802.11 operations so they
are not mac80211 specific. The moving allows some fullmac drivers
to be also benefit from these utility functions.
Signed-off-by: Zhu Yi <yi.zhu@intel.com>
Signed-off-by: Samuel Ortiz <samuel.ortiz@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

My first patch submission used 200ms, which I then somehow
managed to revert back to the earlier 50ms I had used for
some tests in the second patch submission -- but that was
wrong, I should have used 200ms here. Correct that.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Some APs seem to drift away from the expected TBTT (timestamp %
beacon_int_in_usec differs quite a bit from zero) which can result in
us waking up way too early to receive a Beacon frame. In order to work
around this, re-configure the Beacon timers after having received a
Beacon frame from the AP (i.e., when we know the offset between the
expected TBTT and the actual time the AP is sending out the Beacon
frame).
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The previous version used a simple loop to go through all Beacon
frames when determining the next TBTT and DTIM count. This is not too
bad for the case where the setup happens before timesync (i.e., very
small TSF), but this can become very heavy operation if a short Beacon
interval is used and the current TSF is large.

In preparation for a patch to update timer setup based on Beacon
timestamp, optimize this routine to take fixed time regardless of the
actual TSF value.
Signed-off-by: Jouni Malinen <jouni.malinen@atheros.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

SD8688 is a WLAN/Bluetooth combo chip and both functions are supported
in a single firmware image. FUNC_INIT and FUNC_SHUTDOWN commands are
implemented to utilize the multiple function feature.

When SD8688 card is inserted, the firmware image should be downloaded
only once through either WLAN function (Libertas driver) or Bluetooth
function (Bluetooth driver).

This patch adds function init/shutdown for SD8688 WLAN function only.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Usually, the 16-bit rx length is read from scratch pad registers
with two CMD52 transactions:
SD8385: 	IF_SDIO_SCRATCH_OLD (0x80fe/0x80ff)
SD8686/SD8688:	IF_SDIO_SCRATCH     (0x34/0x35)

Alternatively, SD8688 firmware offers an enhanced method for driver
to read an 8-bit rx length (in units) with a single CMD52:
IF_SDIO_RX_UNIT 0x43 is read one time after firmware is ready.
IF_SDIO_RX_LEN  0x42 is read every time when rx interrupt is received.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

replace direct usages of SDIO model numbers with defined macros.
Signed-off-by: Bing Zhao <bzhao@marvell.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The GPSI interface driver does not re-enable the Card Event Interrupt, which
causes problems after a card event (for example: link-loss) comes in.  This
can lead, for example, to the card failing to re-associate.  This patch
ensures that we re-enable the Card Event Interrupt when we handle card events.
Signed-off-by: Andrey Yurovsky <andrey@cozybit.com>
Acked-by: Dan Williams <dcbw@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

In "mac80211: split out and decrease probe wait time" I tried
to reduce the time waiting for a probe response, but failed to
take into account the case where we are detecting beacon loss
in software -- in that case we still wait the monitoring time
rather than the probe wait time. Fix this by refactoring the
mod_timer() calls in ieee80211_associated().
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

The requirement for wireless stats to be atomic is now mostly
artificial since we hold the rtnl _and_ the dev_base_lock for
iterating the device list. Doing that is not required, just the
rtnl is sufficient (and the rtnl is required for other reasons
outlined in commit "wext: fix get_wireless_stats locking").

This will fix http://bugzilla.kernel.org/show_bug.cgi?id=13344
and make things easier for drivers.
Signed-off-by: Johannes Berg <johannes@sipsolutions.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>

Sinec the TCPv6 GRO functions are used in the same file where
they are defined, we do not need to export them.  This was a
cut-n-paste from the IPv4 code which does need to export them.
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>