Convert MDIO bus multiplexer/glue of Amlogic G12a SoC family bindings
to dt-schema.
Reviewed-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

mlx5-updates-2023-01-10

1) From Gal: Add debugfs entries for netdev nic driver
   - ktls, flow steering and hairpin info
   - useful for debug and performance analysis
   - e.g hairpin queue attributes, dump ktls tx pool size, etc

2) From Maher: Update shared buffer configuration on PFC commands
   2.1) For every change of buffer's headroom, recalculate the size of shared
       buffer to be equal to "total_buffer_size" - "new_headroom_size".
       The new shared buffer size will be split in ratio of 3:1 between
       lossy and lossless pools, respectively.

   2.2) For each port buffer change, count the number of lossless buffers.
       If there is only one lossless buffer, then set its lossless pool
       usage threshold to be infinite. Otherwise, if there is more than
       one lossless buffer, set a usage threshold for each lossless buffer.

    While at it, add more verbosity to debug prints when handling user
    commands, to assist in future debug.

3) From Tariq: Throttle high rate FW commands

4) From Shay: Properly initialize management PF

5) Various cleanup patches

Piergiorgio Beruto says:

====================
net: add PLCA RS support and onsemi NCN26000

This patchset adds support for getting/setting the Physical Layer
Collision Avoidace (PLCA) Reconciliation Sublayer (RS) configuration and
status on Ethernet PHYs that supports it.

PLCA is a feature that provides improved media-access performance in terms
of throughput, latency and fairness for multi-drop (P2MP) half-duplex PHYs.
PLCA is defined in Clause 148 of the IEEE802.3 specifications as amended
by 802.3cg-2019. Currently, PLCA is supported by the 10BASE-T1S single-pair
Ethernet PHY defined in the same standard and related amendments. The OPEN
Alliance SIG TC14 defines additional specifications for the 10BASE-T1S PHY,
including a standard register map for PHYs that embeds the PLCA RS (see
PLCA management registers at https://www.opensig.org/about/specifications/).

The changes proposed herein add the appropriate ethtool netlink interface
for configuring the PLCA RS on PHYs that supports it. A separate patchset
further modifies the ethtool userspace program to show and modify the
configuration/status of the PLCA RS.

Additionally, this patchset adds support for the onsemi NCN26000
Industrial Ethernet 10BASE-T1S PHY that uses the newly added PLCA
infrastructure.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for the onsemi NCN26000 10BASE-T1S industrial
Ethernet PHY. The driver supports Point-to-Multipoint operation without
auto-negotiation and with link control handling. The PHY also features
PLCA for improving performance in P2MP mode.
Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support in phylib to read/write PLCA configuration for
Ethernet PHYs that support the OPEN Alliance "10BASE-T1S PLCA
Management Registers" specifications. These can be found at
https://www.opensig.org/about/specifications/Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the required connection between netlink ethtool and
phylib to resolve PLCA get/set config and get status messages.
Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the link modes for the IEEE 802.3cg Clause 147 10BASE-T1S
Ethernet PHY. According to the specifications, the 10BASE-T1S supports
Point-To-Point Full-Duplex, Point-To-Point Half-Duplex and/or
Point-To-Multipoint (AKA Multi-Drop) Half-Duplex operations.
Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add support for configuring the PLCA Reconciliation Sublayer on
multi-drop PHYs that support IEEE802.3cg-2019 Clause 148 (e.g.,
10BASE-T1S). This patch adds the appropriate netlink interface
to ethtool.
Signed-off-by: Piergiorgio Beruto <piergiorgio.beruto@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

'accel_tcp' is allocted by kvzalloc() now, which is a small chunk.
Use kzalloc() directly instead of kvzalloc().
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Return value from mlx5dr_send_postsend_action() directly instead of taking
this in another redundant variable.
Signed-off-by: zhang songyi <zhang.songyi@zte.com.cn>
Reviewed-by: Roi Dayan <roid@nvidia.com>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Zero-length arrays are deprecated[1]. Replace struct mlx5e_rx_wqe_cyc's
"data" 0-length array with a flexible array. Detected with GCC 13,
using -fstrict-flex-arrays=3:

drivers/net/ethernet/mellanox/mlx5/core/en_main.c: In function 'mlx5e_alloc_rq':
drivers/net/ethernet/mellanox/mlx5/core/en_main.c:827:42: warning: array subscript f is outside array bounds of 'struct mlx5_wqe_data_seg[0]' [-Warray-bounds=]
  827 |                                 wqe->data[f].byte_count = 0;
      |                                 ~~~~~~~~~^~~
In file included from drivers/net/ethernet/mellanox/mlx5/core/en/tc_ct.h:11,
                 from drivers/net/ethernet/mellanox/mlx5/core/eswitch.h:48,
                 from drivers/net/ethernet/mellanox/mlx5/core/en_main.c:42:
drivers/net/ethernet/mellanox/mlx5/core/en.h:250:39: note: while referencing 'data'
  250 |         struct mlx5_wqe_data_seg      data[0];
      |                                       ^~~~

[1] https://www.kernel.org/doc/html/latest/process/deprecated.html#zero-length-and-one-element-arrays

Cc: Saeed Mahameed <saeedm@nvidia.com>
Cc: Leon Romanovsky <leon@kernel.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: "Gustavo A. R. Silva" <gustavoars@kernel.org>
Cc: netdev@vger.kernel.org
Cc: linux-rdma@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Jiri Pirko <jiri@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Zero-length arrays are deprecated[1] and we are moving towards
adopting C99 flexible-array members instead. So, replace zero-length
array declaration in struct mlx5e_flow_meter_aso_obj with flex-array
member.

This helps with the ongoing efforts to tighten the FORTIFY_SOURCE
routines on memcpy() and help us make progress towards globally
enabling -fstrict-flex-arrays=3 [2].

Link: https://www.kernel.org/doc/html/latest/process/deprecated.html#zero-length-and-one-element-arrays [1]
Link: https://gcc.gnu.org/pipermail/gcc-patches/2022-October/602902.html [2]
Link: https://github.com/KSPP/linux/issues/78Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Certain connection-based device-offload protocols (like TLS) use
per-connection HW objects to track the state, maintain the context, and
perform the offload properly. Some of these objects are created,
modified, and destroyed via FW commands. Under high connection rate,
this type of FW commands might continuously populate all slots of the FW
command interface and throttle it, while starving other critical control
FW commands.

Limit these throttle commands to using only up to a portion (half) of
the FW command interface slots. FW commands maximal rate is not hit, and
the same high rate is still reached when applying this limitation.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Introduce an opcode getter in the FW command interface, and use it.
Initialize the entry's opcode field early in cmd_alloc_ent() and use it
when possible.
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Enable initialization of DPU Management PF, which is a new loopback PF
designed for communication with BMC.
For now Management PF doesn't support nor require most upper layer
protocols so avoid them.
Signed-off-by: Shay Drory <shayd@nvidia.com>
Reviewed-by: Eran Ben Elisha <eranbe@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

We refer to a TC NIC rule that involves forwarding as "hairpin".
Hairpin queues are mlx5 hardware specific implementation for hardware
forwarding of such packets.

For debug purposes, introduce debugfs files which:
* Expose the number of active hairpins
* Dump the hairpin table
* Allow control over the number and size of the hairpin queues instead
  of the hard-coded values.

This allows us to get visibility of the feature in order to improve it
for next generation hardware.

Add debugfs files:
  fs/tc/hairpin_num_active
  fs/tc/hairpin_num_queues
  fs/tc/hairpin_queue_size
  fs/tc/hairpin_table_dump

Note that the new values will only take effect on the next queues
creation, it does not affect existing queues.
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Add a debugfs directory for flow steering related information.
The directory is currently empty, and will hold the 'tc' subdirectory in
a downstream patch.
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

In preparation for downstream work to expose hairpin queues parameters,
introduce a hairpin parameters struct as part of the tc structure.
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Add TLS debugfs to improve observability by exposing the size of the tls
TX pool.

To observe the size of the TX pool:
$ cat /sys/kernel/debug/mlx5/<pci>/nic/tls/tx/pool_size
Signed-off-by: Tariq Toukan <tariqt@nvidia.com>
Co-developed-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Gal Pressman <gal@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Similar to the mlx5_core debugfs, lay the groundwork for mlx5e debugfs
files under /sys/kernel/debug/mlx5/<pci>/nic/..
Signed-off-by: Gal Pressman <gal@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Currently, the user can modify device's receive buffer size, modify the
mapping between QoS priority groups to buffers and change the buffer
state to become lossy/lossless via pfc command.

However, the shared receive buffer pool alignments, as a result of
such commands, is performed only when the shared buffer is in FW ownership.
When a user changes the mapping of priority groups or buffer size,
the shared buffer is moved to SW ownership.

Therefore, for devices that support shared buffer, handle the shared buffer
alignments in accordance to user's desired configurations.

Meaning, the following will be performed:
1. For every change of buffer's headroom, recalculate the size of shared
   buffer to be equal to "total_buffer_size" - "new_headroom_size".
   The new shared buffer size will be split in ratio of 3:1 between
   lossy and lossless pools, respectively.

2. For each port buffer change, count the number of lossless buffers.
   If there is only one lossless buffer, then set its lossless pool
   usage threshold to be infinite. Otherwise, if there is more than
   one lossless buffer, set a usage threshold for each lossless buffer.

While at it, add more verbosity to debug prints when handling user
commands, to assist in future debug.
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

To allow users to configure shared receive buffer parameters through
dcbnl callbacks, expose an API to query and modify SBPR and SBCM registers,
which will be used in the upcoming patch.
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Add the shared receive buffer management and configuration registers:
1. SBPR - Shared Buffer Pools Register
2. SBCM - Shared Buffer Class Management Register
Signed-off-by: Maher Sanalla <msanalla@nvidia.com>
Reviewed-by: Moshe Shemesh <moshe@nvidia.com>
Signed-off-by: Saeed Mahameed <saeedm@nvidia.com>

Fix a typo of "permision" which should be "permission".
Signed-off-by: Dai Shixin <dai.shixin@zte.com.cn>
Signed-off-by: Yang Yang <yang.yang29@zte.com.cn>
Link: https://lore.kernel.org/r/202301091935262709751@zte.com.cnSigned-off-by: Jakub Kicinski <kuba@kernel.org>

Michael Walle says:

====================
net: mdio: Start separating C22 and C45

This patch set starts the separation of C22 and C45 MDIO bus
transactions at the API level to the MDIO Bus drivers. C45 read and
write ops are added to the MDIO bus driver structure, and the MDIO
core will try to use these ops if requested to perform a C45
transfer. If not available a fallback to the older API is made, to
allow backwards compatibility until all drivers are converted.

A few drivers are then converted to this new API.

The core DSA patch was dropped for now as there is still an ongoing
discussion. It will be picked up in a later series again.

v2: https://lore.kernel.org/r/20221227-v6-2-rc1-c45-seperation-v2-0-ddb37710e5a7@walle.cc
v1: https://lore.kernel.org/r/20220508153049.427227-1-andrew@lunn.ch
====================

Link: https://lore.kernel.org/r/20221227-v6-2-rc1-c45-seperation-v3-0-ade1deb438da@walle.ccSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The global2 SMI MDIO bus driver can perform both C22 and C45
transfers. Create separate functions for each and register the C45
versions using the new API calls where appropriate. Update the SERDES
code to make use of these new accessors.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Some DSA devices pass through PHY access to the MDIO bus the switch is
on. Add C45 versions of the current C22 helpers for nested accesses to
MDIO busses, so that C22 and C45 can be separated in these DSA
drivers.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The fec MDIO bus driver can perform both C22 and C45 transfers.
Create separate functions for each and register the C45 versions using
the new API calls where appropriate.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The xgmac MDIO bus driver can perform both C22 and C45 transfers.
Create separate functions for each and register the C45 versions using
the new API calls where appropriate.

While at it, remove the misleading comment. According to Vladimir
Oltean:
 - miimcom is a register accessed by fsl_pq_mdio.c, not by xgmac_mdio.c
 - "device dev" doesn't really refer to anything (maybe "dev_addr").
 - I don't understand what is meant by the comment "All PHY
   configuration has to be done through the TSEC1 MIIM regs". Or rather
   said, I think I understand, but it is irrelevant to the driver for 2
   reasons:
    * TSEC devices use the fsl_pq_mdio.c driver, not this one
    * It doesn't matter to this driver whose TSEC registers are used for
      MDIO access. The driver just works with the registers it's given,
      which is a concern for the device tree.
 - barring the above, the rest just describes the MDIO bus API, which is
   superfluous
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The marvell MDIO driver supports two different hardware blocks. The
XSMI block is C45 only. Convert this block to the new API, and only
populate the c45 calls in the bus structure.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

The bitbbanging bus driver can perform both C22 and C45 transfers.
Create separate functions for each and register the C45 versions using
the new driver API calls.

The SH Ethernet driver places wrappers around these functions. In
order to not break boards which might be using C45, add similar
wrappers for C45 operations.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Now that mdiobus_c45_addr() is only used within the MDIO code during
fallback, move the function next to its only users. This function
should not be used any more in drivers, the c45 helpers should be used
in its place, so hiding it away will prevent any new users from being
added.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

When performing a C22 operation, check that the bus driver actually
provides the methods, and return -EOPNOTSUPP if not. C45 only busses
do exist, and in future their C22 methods will be NULL.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Now that C45 uses its own read/write methods, the validation performed
when a bus is registers needs updating. All combinations of C22 and
C45 are supported, but both read and write methods must be provided,
read only busses are not supported etc.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Convert the PCS-XPCS driver to make use of the C45 MDIO bus API for
modify_change().
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Currently C22 and C45 transactions are mixed over a combined API calls
which make use of a special bit in the reg address to indicate if a
C45 transaction should be performed. This makes it impossible to know
if the bus driver actually supports C45. Additionally, many C22 only
drivers don't return -EOPNOTSUPP when asked to perform a C45
transaction, they mistaking perform a C22 transaction.

This is the first step to cleanly separate C22 from C45. To maintain
backwards compatibility until all drivers which are capable of
performing C45 are converted to this new API, the helper functions
will fall back to the older API if the new API is not
supported. Eventually this fallback will be removed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

Michael Walle says:

====================
net: phy: mxl-gpy: broken interrupt fixes

The GPY215 has a broken interrupt pin. This patch series tries to
workaround that and because in general that is not possible, disables the
interrupts by default and falls back to polling mode. There is an opt-in
via the devicetree.

====================

Link: https://lore.kernel.org/r/20230109123013.3094144-1-michael@walle.ccSigned-off-by: Paolo Abeni <pabeni@redhat.com>

The interrupts on the GPY215B and GPY215C are broken and the only viable
fix is to disable them altogether. There is still the possibilty to
opt-in via the device tree.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Until now, it is not possible for a PHY driver to disable interrupts
during runtime. If a driver offers the .config_intr() as well as the
.handle_interrupt() ops, it is eligible for interrupt handling.
Introduce a new flag for the dev_flags property of struct phy_device, which
can be set by PHY driver to skip interrupt setup and fall back to polling
mode.

At the moment, this is used for the MaxLinear PHY which has broken
interrupt handling and there is a need to disable interrupts in some
cases.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

Add the device tree bindings for the MaxLinear GPY2xx PHYs, which
essentially adds just one flag: maxlinear,use-broken-interrupts.

One might argue, that if interrupts are broken, just don't use
the interrupt property in the first place. But it needs to be more
nuanced. First, this interrupt line is also used to wake up systems by
WoL, which has nothing to do with the (broken) PHY interrupt handling.

Second and more importantly, there are devicetrees which have this
property set. Thus, within the driver we have to switch off interrupt
handling by default as a workaround. But OTOH, a systems designer who
knows the hardware and knows there are no shared interrupts for example,
can use this new property as a hint to the driver that it can enable the
interrupt nonetheless.
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>