Merge "Device Tree changes" from Florian Fainelli:

New devices:

- Felix adds support for the Buffalo WXR-1900DHP and adds the USB led on Buffalo
  WZR-1750DHP

- Rafal adds support for the SmartRG SR400ac, Asus RT-AC68U and RT-AC56U

New peripheral support:

- Brian adds Device Tree nodes for the Broadcom NAND controller found on
  BCM7xxx, BCM63138 and Cygnus SoCs

- Brian adds Device Tree nodes for the SATA AHCI and PHY controller found on
  BCM7xxx

- I add the Device Tree nodes and bindings documents for bringing-up secondary
  CPUs and timer/syscon-reboot on BCM63138

* tag 'arm-soc/for-4.2/dts' of http://github.com/broadcom/stblinux:
  ARM: BCM5301X: Add DT for Asus RT-AC56U
  ARM: BCM5301X: Add DT for Asus RT-AC68U
  ARM: dts: BCM63xx: Add timer and syscon-reboot nodes
  dt-bindings: Add documentation for the BCM63138 timer and syscon-reboot
  ARM: dts: brcmstb: add nodes for SATA controller and PHY
  ARM: dts: cygnus: Enable NAND support for Cygnus
  ARM: bcm63138: add NAND DT support
  ARM: bcm7445: add NAND to DTS
  ARM: BCM5301X: Add DT for SmartRG SR400ac
  ARM: BCM5301X: Add DT for Buffalo WXR-1900DHP
  ARM: BCM5301X: Add USB LED for Buffalo WZR-1750DHP
  ARM: dts: BCM63xx: Add SMP nodes and required properties
  Documentation: DT: Document SMP DT nodes and properties for BCM63138
  ARM: dts: BCM63xx: Add PMB busses nodes
  Documentation: DT: Add Broadcom BCM63138 PMB binding

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add a "brcm,bcm6328-timer" and "syscon-reboot" nodes to allow the
generic syscon-reboot driver to reset a BCM63138 SoC.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

A timer node and a syscon-reboot node are required for software reboot
to work on BCM63138, document these two nodes in the platform binding.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Enable NAND support for Broadcom Cygnus SoC
Signed-off-by: Ray Jui <rjui@broadcom.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Signed-off-by: Brian Norris <computersforpeace@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Update bcm63138.dtsi with the following:

- enable-method for both CPU nodes
- brcm,bcm63138-bootlut node
- resets properties to point to the correct PMB controller to release
  the secondary CPU from reset
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add binding documentation for the additional nodes and properties
required to get the secondary CPU online on the BCM63138 SoC.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add the two BCM63138 PMB busses nodes found on this System-on-a-Chip as
described in their corresponding binding document.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Add a Device Tree binding for the Broadcom BCM63138 Processor Monitor
Bus, which is an internal bus used to access different power and reset
signals within a BCM63138 System-on-a-Chip.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>

Merge tag 'tegra-for-4.2-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/dt

Merge "ARM: tegra: Devicetree changes for v4.2-rc1" from Thierry Reding:

Contains a couple of fixes and additions to device tree files. The most
notable change is a fix for a misapplied patch that was only exposed by
a recent change in the regulator subsystem that caused USB to break on
Tegra124 recently.

Other than that there are a more or less random assortment of additions
to enable various features on a couple of boards.

* tag 'tegra-for-4.2-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
  ARM: tegra: Fix hda2codec_2x clock and reset names
  ARM: tegra: Add Tegra30 HDA support
  ARM: tegra: Cardhu device-tree comment spelling fix
  ARM: tegra: venice2: Set min-/max-microvolt for VDD_LED supply
  ARM: tegra: venice2: Mark eMMC as non-removable
  ARM: tegra: jetson-tk1: Enable HDA support
  ARM: tegra: Add missing HDMI +5V regulator
  ARM: tegra: cardhu: Add power and volume keys
  ARM: tegra: Correct which USB controller has the UTMI pad registers

Merge tag 'socfpga_dts_for_v4.2_part_2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/dt

Merge "SoCFPGA update for v4.2 part 2" from Dinh Nguyen:
- Add a DTS node for the A9 SCU

* tag 'socfpga_dts_for_v4.2_part_2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
  ARM: socfpga: dts: add the a9-scu node

Merge tag 'v4.2-rockchip-dts1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into next/dt

Merge "ARM: rockchip: dts changes for 4.2" from Heiko Stuebner:

Some misc improvements defining additional supply regulators, enabling
the Cortex-A12 HW PMU on the rk3288 and the tsadc on some more rk3288
boards, as well as some usb properties and marking the radxarock pmic
as system-power-controller.

* tag 'v4.2-rockchip-dts1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
  ARM: dts: rockchip: add system-power-controller to act8846 on radxarock
  ARM: dts: rockchip: add properties for dwc2 usb otg controller
  ARM: dts: rockchip: enable tsadc on rk3288 boards
  ARM: dts: rockchip: add act8846 supplies on rk3288-firefly
  ARM: dts: rockchip: Specify VMMC and VQMMC on rk3288-evb
  ARM: dts: rockchip: Enable Cortex-A12 HW PMU events on rk3288

Add the dts node for the A9 SCU.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>

Merge tag 'ux500-v4.2-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson into next/dt

Merge "Ux500 Device Tree changes for the v4.2 series" form Linus Walleij:

Define CPU topology, connect that with CoreSight blocks,
add sensor information to DT boards.

* tag 'ux500-v4.2-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
  ARM: ux500: add the sensors to the STUIB board
  ARM: ux500: assign the sensor trigger IRQs
  ARM: ux500: fix lsm303dlh magnetometer compat string
  ARM: ux500: add CoreSight blocks to DTS file
  ARM: ux500: define CPU topology

This adds the device tree data for the LIS331DL and the
AK8974 magnetometer to the STUIB board device tree include
file.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The ST sensors on the Ux500 boards were not utilizing the IRQs
for data ready sample triggers. Enable this by assigning the
right GPIO lines and interrupt lines (when the GPIO lines are
used for IRQs) to the accelerometer, gyro and magnetometer
sensors.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The magnetometer found on the Ux500 TVK and Snowball boards
is a LSM303DLH not a LSM303DLM, small differences but still
different. Put in the right compatible strings and things start
working smoothly.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

This registers all the CoreSight blocks on the DB8500 SoC:
each core has a PTM (v1.0, r1p0-00rel0) connected, both connected
to a funnel (DK-TM908-r0p1-00rel0) which in turn connects to a
replicator (DM-TM909-r0p1-00rel0). The replicator has two outputs,
port 0 to a TPIU interface and port 1 to an ETB
(DK-TM907-r0p3-00rel0). The CoreSight blocks are all clocked by
the APEATCLK from the PRCMU and their AHB interconnect is clocked
from a separate clock called APETRACECLK.

The SoC also has a CTI/CTM block which can be added later as we
have upstream support in the CoreSight subsystem.
Acked-by: Mathieu Poirier <mathieu.poirier@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>

The act8846 is the main pmic and system-power-controller on radxarock boards,
so add the necessary property.
Signed-off-by: Michael Niewoehner <mniewoeh@stud.hs-offenburg.de>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>

Merge tag 'sunxi-dt-for-4.2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux into next/dt

Pull "Allwinner DT additions for 4.1, take 1" from Maxime Ripard:

All the device tree related changes for the 4.1 merge window.

It has a rather big diffstat, because of a lot of mechanical and harmless
changes, as described below.

There is mostly:
  - The end of the DT relicensing. All our DT should now be under the dual
    X11/GPL license.
  - Convertion of all the DT to a label based syntax, instead of
    duplicating the tree like was done before.
  - Rework of the A10s and A13 DTSI to share the common devices
  - A few drivers enablings: A80 USB, the A31 PMIC, A31 and A23 arch
    timers, etc
  - Fix the checkpatch warnings
  - A few new boards : cubieboard4, mele i7, utoo p66, auxtex t004,
    pcduino3 nano, gemei G9, mk808c, jesurun q5, orange pi, orange pi mini

* tag 'sunxi-dt-for-4.2' of https://git.kernel.org/pub/scm/linux/kernel/git/mripard/linux: (84 commits)
  ARM: sunxi: dt: Split the SPI pinctrl groups
  ARM: sunxi: dt: Fix whitespace errors
  ARM: sunxi: DT: Fix lines over 80 characters
  ARM: sunxi: dt: Remove the FSF address
  ARM: sunxi: dts: split IR pins for A10 and A20
  ARM: sun7i: dt: Add new MK808C device
  ARM: dts: sun6i: Set PLL6 as parent to AHB1 clock in AHB1 clock node
  ARM: dts: sunxi: Update ahb clocks for sun5i and sun7i
  ARM: dts: sun7i: Add dts file for the Jesurun Q5 top set box
  ARM: dts: sun5i: Enable touchscreen on Utoo P66
  ARM: dts: sun7i: Add dts file for the Orangepi mini SBC
  ARM: dts: sun7i: Add dts file for the Orangepi SBC
  ARM: dts: sun7i: Add A20 SRAM and SRAM controller
  ARM: dts: sun5i: Add A13 and A10s SRAM and SRAM controller
  ARM: dts: sun4i: Add A10 SRAM and SRAM controller
  ARM: dts: sun5i: Add broken-hpi property for Utoo-P66 eMMC
  ARM: sun8i: dt: Enable A23 SMP support
  ARM: dts: sun6i: Add cpu thermal zones to dtsi
  ARM: dts: sun6i: Add cpu clock reference and operating points to dtsi
  ARM: sunxi: DT: Add stdout-path property
  ...

Merge tag 'socfpga_dts_for_v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into next/dt

Pull "SoCFPGA DTS updates for v4.2" from Dinh Nguyen:

- Add accelerometer to sockit
- Update and clean up support for the Arria10 platform
- Add sdmmc_clk/4 clock node SoCFPGA Cyclone5/Arria5
- Update ethernet nodes with multicast/unicast/fifo-depth properties
- Add clocks for Arria10 platform

* tag 'socfpga_dts_for_v4.2' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
  ARM: socfpga: dts: add clocks to the Arria10 platform
  ARM: socfpga: dts: Add tx-fifo-depth and rx-fifo-depth properties
  ARM: socfpga: dts: Add multicast bins and unicast filter entries
  ARM: socfpga: dts: Add a clock node for sdmmc CIU
  ARM: socfpga: dts: rename socdk board file to socdk_sdmmc
  ARM: socfpga: dts: enable UART1 for the debug uart
  ARM: socfpga: dts: disable the sdmmc, and uart nodes in the base arria10
  ARM: socfpga: dts: add cpu1-start-addr for Arria 10
  ARM: socfpga: dts: Add adxl34x

Pull "First batch of DT changes for 4.2" from Nicolas Ferre:

- cleanup and addition of Overkiz boards
- at91sam9x5: pwm0 pinctrl definition
- delete deprecated mainck nodes

* tag 'at91-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/nferre/linux-at91:
  ARM: at91/dt: drop deprecated mainck node from pmc
  ARM: at91/dt: add support for kizbox2
  ARM: at91/dt: add support for kizboxmini
  ARM: at91/dt: sam9x5: add pinctrl for pwm0
  ARM: at91/dt: at91-kizbox: update chosen node
  ARM: at91/dt: at91-kizbox: re-size nand partitions
  ARM: at91/dt: at91-kizbox: leds related changes
  ARM: at91/dt: at91-kizbox: gpio-keys related changes
  ARM: at91/dt: at91-kizbox: user proper serial uart
  ARM: at91/dt: at91-kizbox: sanitize file
  ARM: at91/dt: kizbox: rename to at91-kizbox

Merge "ARM: DT: Hisilicon hip04 soc and D01 board updates for 4.2" from Wei Xu:

- Add hip04 GPIO nodes
- Add NANDC nodes for hip04 and D01 board
- Add hip04 ethernet related nodes

* tag 'hip04-dt-for-4.2' of git://github.com/hisilicon/linux-hisi:
  ARM: dts: add HiSilicon hip04 ethernet controller resource
  mtd: hisilicon: add device tree node for NAND controller
  ARM: dts: hip04: add GPIO pieces

Initial device trees for UniPhier SoCs: PH1-sLD3, PH1-LD4, PH1-Pro4,
and PH1-sLD8.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Merge tag 'sti-dt-for-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mcoquelin/sti into next/dt

Pull "STi DT updates for v4.2, round 1." from Maxime Coquelin:

Highlights:
-----------
 - Add DT nodes for SSC on STiH407 family
 - Add DT nodes for SD/MMC on STiH407 & STiH418
 - Add DT node for LPC on STiH407
 - Add Sata DT nodes for STiH407
 - Fix PIO3 & PIO35 pins retiming on STiH407

* tag 'sti-dt-for-v4.2-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mcoquelin/sti:
  ARM: DT: STi: STiH407: Add sata DT nodes.
  ARM: STi: DT: STiH407: Fix retime pin mask for PIO5 and PIO35
  ARM: STi: DT: STiH407: Add Device Tree node for the LPC
  mfd: dt-bindings: Provide human readable defines for LPC mode choosing
  ARM: STi: DT: STiH418: Add dt nodes for sdhci and emmc.
  ARM: STi: DT: STiH407: Add dt nodes for sdhci and emmc.
  ARM: sti: Provide DT nodes for SBC SSC[0..2]
  ARM: sti: Provide DT nodes for SSC[0..4]

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>

Add all the clock nodes for the Arria10 platform. At the same time, update
the peripherals with their respective clocks property.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
---
v2: Add the l4_sys_free_clk node

Add tx-fifo-depth and rx-fifo-depth devicetree properties for socfpga
stmmac. These devicetree properties will be used to configure certain
features of the stmmac on the socfpga.
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>

Add multicast-filter-bins and perfect-filter-entries configuration properties
to the socfpga devicetree for the Arria 10 socfpga.
Signed-off-by: Vince Bridgers <vbridger@opensource.altera.com>
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>

The CIU(Card Interface Unit) get its clock from the sdmmc_clk_divided clock
which is used to clock the card. The sdmmc_clk_divided clock is the sdmmc_clk
passed through a fixed divider of 4. This patch adds the sdmmc_clk_divided
node and makes the sdmmc_clk it's parent.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
---
v2: renamed ciu_clk to sdmmc_clk_divided

Rename the socfpga_arria10_socdk board file to socfpga_arria10_socdk_sdmmc
as Arria 10 devkit cannot support SDMMC and QSPI at the same time. Thus
we will need to have 2 separate board files, one for SDMMC and one for
QSPI. We also add a new base board dtsi file, socfpga_arria10_socdk.dtsi
so that we use common peripherals for each flavor of the devkits.

Add the sdmmc node to the socfpga_arria10_socdk_sdmmc.dts board file.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>

Arria10 devkit is using UART1 for the debug uart port. Remove
unused aliases.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
---
v2: Add removal of unused aliases