Alexandre TORGUE says:

====================
Enhance stmmac driver to support GMAC4.x IP

This is a subset of patch to enhance current stmmac driver to support
new GMAC4.x chips. New set of callbacks is defined to support this new
family: descriptors, dma, core.

One of main changes of GMAC 4.xx IP is descriptors management.
 -descriptors are only used in ring mode.
 -A descriptor is composed of 4 32bits registers (no more extended
  descriptors)
 -descriptor mechanism (Tx for example, but it is exactly the same for RX):
 -useful registers:
  -DMA_CH#_TxDesc_Ring_Len: length of transmit descriptor ring
  -DMA_CH#_TxDesc_List_Address: start address of the ring
  -DMA_CH#_TxDesc_Tail_Pointer: address of the last descriptor to send + 1.
  -DMA_CH#_TxDesc_Current_App_TxDesc: address of the current descriptor

 -The descriptor Tail Pointer register contains the pointer to the
  descriptor address (N). The base address and the current
  descriptor decide the address of the current descriptor that the
  DMA can process. The descriptors up to one location less than the
  one indicated by the descriptor tail pointer (N-1) are owned by
  the DMA. The DMA continues to process the descriptors until the
  following condition occurs:
  "current descriptor pointer == Descriptor Tail pointer"

  Then the DMA goes into suspend mode. The application must perform
  a write to descriptor tail pointer register and update the tail
  pointer to have the following condition and to start a new transfer:
  "current descriptor pointer < Descriptor tail pointer"

  The DMA automatically wraps around the base address when the end
  of ring is reached.

New features are available on IP:
 -TSO (TCP Segmentation Offload) for TX only
 -Split header: to have header and payload in 2 different buffers (not yet implemented)

Below some throughput figures obtained on some boxes:

                        iperf (mbps)
--------------------------------------
                       tcp     udp
                    tx   rx   tx  rx
                     -----------------
    GMAC4.x         935  930  750 800

Note: There is a change in 4.10a databook on bitfield mapping of DMA_CHANx_INTR_ENA register.
This requires to have é diffrent set of callbacks between IP 4.00a and 4.10a.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch just updates the driver to the version fully
tested on STi platforms. This version is Jan_2016.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Update stmmac driver documentation according to new GMAC 4.x family.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the whole GMAC4 support inside the
stmmac d.d. now able to use the new HW and some new features
i.e.: TSO.
It is missing the multi-queue and split Header support at this
stage.
This patch also updates the driver version and the stmmac.txt.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is to support the snps,dwmac-4.00 and snps,dwmac-4.10a
and related features on the platform driver.
See binding doc for further details.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For gmac3, the MMC addr map is: 0x100 - 0x2fc
For gmac4, the MMC addr map is: 0x700 - 0x8fc

So instead of adding 0x600 to the IO address when setup the mmc,
the RMON base address is saved inside the private structure and
then used to manage the counters.
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is the initial support for GMAC4 that includes
the main callbacks to setup the core module: including
Csum, basic filtering, mac address and interrupt (MMC,
MTL, PMT) No LPI added.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

DMA behavior is linked to descriptor management:

-descriptor mechanism (Tx for example, but it is exactly the same for RX):
-useful registers:
-DMA_CH#_TxDesc_Ring_Len: length of transmit descriptor ring
-DMA_CH#_TxDesc_List_Address: start address of the ring
	-DMA_CH#_TxDesc_Tail_Pointer: address of the last
					      descriptor to send + 1.
	-DMA_CH#_TxDesc_Current_App_TxDesc: address of the current
						    descriptor

-The descriptor Tail Pointer register contains the pointer to the
 descriptor address (N). The base address and the current
 descriptor decide the address of the current descriptor that the
 DMA can process. The descriptors up to one location less than the
 one indicated by the descriptor tail pointer (N-1) are owned by
 the DMA. The DMA continues to process the descriptors until the
 following condition occurs:
 "current descriptor pointer == Descriptor Tail pointer"

Then the DMA goes into suspend mode. The application must perform
a write to descriptor tail pointer register and update the tail
pointer to have the following condition and to start a new transfer:
"current descriptor pointer < Descriptor tail pointer"

The DMA automatically wraps around the base address when the end
of ring is reached.

Up to 8 DMA could be use but currently we only use one (channel0)
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is the main header file to define all the
macro used for GMAC4 DMA and CORE parts.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

One of main changes of GMAC 4.xx IP is descriptors management.
-descriptors are only used in ring mode.
-A descriptor is composed of 4 32bits registers (no more extended
 descriptors)
-descriptor mechanism (Tx for example, but it is exactly the same for RX):
-useful registers:
	-DMA_CH#_TxDesc_Ring_Len: length of transmit descriptor
				   ring
	-DMA_CH#_TxDesc_List_Address: start address of the ring
	-DMA_CH#_TxDesc_Tail_Pointer: address of the last
				      descriptor to send + 1.
	-DMA_CH#_TxDesc_Current_App_TxDesc: address of the current
					    descriptor

-The descriptor Tail Pointer register contains the pointer to the
 descriptor address (N). The base address and the current
 descriptor decide the address of the current descriptor that the
 DMA can process. The descriptors up to one location less than the
 one indicated by the descriptor tail pointer (N-1) are owned by
 the DMA. The DMA continues to process the descriptors until the
 following condition occurs:
 "current descriptor pointer == Descriptor Tail pointer"

  Then the DMA goes into suspend mode. The application must perform
  a write to descriptor tail pointer register and update the tail
  pointer to have the following condition and to start a new
      transfer:
  "current descriptor pointer < Descriptor tail pointer"

  The DMA automatically wraps around the base address when the end
  of ring is reached.

-New features are available on IP:
-TSO (TCP Segmentation Offload) for TX only
-Split header: to have header and payload in 2 different buffers
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

synopsys_uid is only used once after setup, to get synopsys_id
by using shitf/mask operation. It's no longer used then.
So, remove this temporary variable and directly compute
synopsys_id from setup routine.
Acked-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

To avoid lot of check in stmmac_main for display ring management
and support the GMAC4 chip, the display_ring function is moved
into dedicated descriptor file.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

On next GMAC IP generation (4.xx), the way to get hw feature
is not the same than on previous 3.xx. As it is hardware
dependent, the way to get hw capabilities should be defined in dma ops of
each MAC IP. It will avoid also a huge computation of hw capabilities in
stmmac_main.
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The patch adds support of pause ctrl for HNS V2, and this feature is lost
by HNS V1:
       1) service ports can disable rx pause frame,
       2) debug ports can open tx/rx pause frame.

And this patch updates the REGs about the pause ctrl when updated
status function called by upper layer routine.
Signed-off-by: Lisheng <lisheng011@huawei.com>
Signed-off-by: Yisen Zhuang <Yisen.Zhuang@huawei.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since nla_get_in_addr and nla_put_in_addr were implemented,
so use them appropriately.
Signed-off-by: Haishuang Yan <yanhaishuang@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

For non-SACK connections, cwnd is lowered to inflight plus 3 packets
when the recovery ends. This is an optional feature in the NewReno
RFC 2582 to reduce the potential burst when cwnd is "re-opened"
after recovery and inflight is low.

This feature is questionably effective because of PRR: when
the recovery ends (i.e., snd_una == high_seq) NewReno holds the
CA_Recovery state for another round trip to prevent false fast
retransmits. But if the inflight is low, PRR will overwrite the
moderated cwnd in tcp_cwnd_reduction() later regardlessly. So if a
receiver responds bogus ACKs (i.e., acking future data) to speed up
transfer after recovery, it can only induce a burst up to a window
worth of data packets by acking up to SND.NXT. A restart from (short)
idle or receiving streched ACKs can both cause such bursts as well.

On the other hand, if the recovery ends because the sender
detects the losses were spurious (e.g., reordering). This feature
unconditionally lowers a reverted cwnd even though nothing
was lost.

By principle loss recovery module should not update cwnd. Further
pacing is much more effective to reduce burst. Hence this patch
removes the cwnd moderation feature.

v2 changes: revised commit message on bogus ACKs and burst, and
            missing signature
Signed-off-by: Matt Mathis <mattmathis@google.com>
Signed-off-by: Neal Cardwell <ncardwell@google.com>
Signed-off-by: Soheil Hassas Yeganeh <soheil@google.com>
Signed-off-by: Yuchung Cheng <ycheng@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from David Miller:

 1) Missing device reference in IPSEC input path results in crashes
    during device unregistration.  From Subash Abhinov Kasiviswanathan.

 2) Per-queue ISR register writes not being done properly in macb
    driver, from Cyrille Pitchen.

 3) Stats accounting bugs in bcmgenet, from Patri Gynther.

 4) Lightweight tunnel's TTL and TOS were swapped in netlink dumps, from
    Quentin Armitage.

 5) SXGBE driver has off-by-one in probe error paths, from Rasmus
    Villemoes.

 6) Fix race in save/swap/delete options in netfilter ipset, from
    Vishwanath Pai.

 7) Ageing time of bridge not set properly when not operating over a
    switchdev device.  Fix from Haishuang Yan.

 8) Fix GRO regression wrt nested FOU/GUE based tunnels, from Alexander
    Duyck.

 9) IPV6 UDP code bumps wrong stats, from Eric Dumazet.

10) FEC driver should only access registers that actually exist on the
    given chipset, fix from Fabio Estevam.

* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (73 commits)
  net: mvneta: fix changing MTU when using per-cpu processing
  stmmac: fix MDIO settings
  Revert "stmmac: Fix 'eth0: No PHY found' regression"
  stmmac: fix TX normal DESC
  net: mvneta: use cache_line_size() to get cacheline size
  net: mvpp2: use cache_line_size() to get cacheline size
  net: mvpp2: fix maybe-uninitialized warning
  tun, bpf: fix suspicious RCU usage in tun_{attach, detach}_filter
  net: usb: cdc_ncm: adding Telit LE910 V2 mobile broadband card
  rtnl: fix msg size calculation in if_nlmsg_size()
  fec: Do not access unexisting register in Coldfire
  net: mvneta: replace MVNETA_CPU_D_CACHE_LINE_SIZE with L1_CACHE_BYTES
  net: mvpp2: replace MVPP2_CPU_D_CACHE_LINE_SIZE with L1_CACHE_BYTES
  net: dsa: mv88e6xxx: Clear the PDOWN bit on setup
  net: dsa: mv88e6xxx: Introduce _mv88e6xxx_phy_page_{read, write}
  bpf: make padding in bpf_tunnel_key explicit
  ipv6: udp: fix UDP_MIB_IGNOREDMULTI updates
  bnxt_en: Fix ethtool -a reporting.
  bnxt_en: Fix typo in bnxt_hwrm_set_pause_common().
  bnxt_en: Implement proper firmware message padding.
  ...

Pull clk fixes from Stephen Boyd:
 "A handful of const updates for reset ops and a couple fixes to the
  newly introduced IPQ4019 clock driver"

* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
  clk: qcom: ipq4019: add some fixed clocks for ddrppl and fepll
  clk: qcom: ipq4019: switch remaining defines to enums
  clk: qcom: Make reset_control_ops const
  clk: tegra: Make reset_control_ops const
  clk: sunxi: Make reset_control_ops const
  clk: atlas7: Make reset_control_ops const
  clk: rockchip: Make reset_control_ops const
  clk: mmp: Make reset_control_ops const
  clk: mediatek: Make reset_control_ops const

Pull power management and ACPI fix from Rafael J. Wysocki:
 "Just one fix for a nasty boot failure on some systems based on Intel
  Skylake that shipped with broken firmware where enabling
  hardware-coordinated P-states management (HWP) causes a faulty
  interrupt handler in SMM to be invoked and crash the system (Srinivas
  Pandruvada)"

* tag 'pm+acpi-4.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  ACPI / processor: Request native thermal interrupt handling via _OSC

Merge fixes from Andrew Morton:
 "11 fixes"

* emailed patches from Andrew Morton <akpm@linux-foundation.org>:
  .mailmap: add Christophe Ricard
  Make CONFIG_FHANDLE default y
  mm/page_isolation.c: fix the function comments
  oom, oom_reaper: do not enqueue task if it is on the oom_reaper_list head
  mm/page_isolation: fix tracepoint to mirror check function behavior
  mm/rmap: batched invalidations should use existing api
  x86/mm: TLB_REMOTE_SEND_IPI should count pages
  mm: fix invalid node in alloc_migrate_target()
  include/linux/huge_mm.h: return NULL instead of false for pmd_trans_huge_lock()
  mm, kasan: fix compilation for CONFIG_SLAB
  MAINTAINERS: orangefs mailing list is subscribers-only

* acpi-processor:
  ACPI / processor: Request native thermal interrupt handling via _OSC

Pull btrfs fixes from Chris Mason:
 "This has a few fixes Dave Sterba had queued up.  These are all pretty
  small, but since they were tested I decided against waiting for more"

* 'for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  btrfs: transaction_kthread() is not freezable
  btrfs: cleaner_kthread() doesn't need explicit freeze
  btrfs: do not write corrupted metadata blocks to disk
  btrfs: csum_tree_block: return proper errno value

Pull OrangeFS fixes from Martin Brandenburg:
 "Two bugfixes for OrangeFS.

  One is a reference counting bug and the other is a typo in client
  minimum version"

* tag 'for-linus' of git://github.com/martinbrandenburg/linux:
  orangefs: minimum userspace version is 2.9.3
  orangefs: don't put readdir slot twice

Pull arm64 fixes from Will Deacon:

 - fix oops when patching in alternative sequences on big-endian CPUs

 - reconcile asm/perf_event.h after merge window fallout with KVM ARM

 - defconfig updates

* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
  arm64: defconfig: updates for 4.6
  arm64: perf: Move PMU register related defines to asm/perf_event.h
  arm64: opcodes.h: Add arm big-endian config options before including arm header

Pull sound fixes from Takashi Iwai:
 "A collection of small fixes:

   - a fix in ALSA timer core to avoid possible BUG() trigger
   - a fix in ALSA timer core 32bit compat layer
   - a few HD-audio quirks for ASUS and HP machines
   - AMD HD-audio HDMI controller quirks
   - fixes of USB-audio double-free at some error paths
   - a fix for memory leak in DICE driver at hotunplug"

* tag 'sound-4.6-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound:
  ALSA: timer: Use mod_timer() for rearming the system timer
  ALSA: hda - fix front mic problem for a HP desktop
  ALSA: usb-audio: Fix double-free in error paths after snd_usb_add_audio_stream() call
  ALSA: hda: add AMD Polaris-10/11 AZ PCI IDs with proper driver caps
  ALSA: dice: fix memory leak when unplugging
  ALSA: hda - Apply fix for white noise on Asus N550JV, too
  ALSA: hda - Fix white noise on Asus N750JV headphone
  ALSA: hda - Asus N750JV external subwoofer fixup
  ALSA: timer: fix gparams ioctl compatibility for different architectures

Different computers had different settings in the mail client.  Some
contributions appear as Christophe Ricard, others as Christophe RICARD.
Signed-off-by: Christophe Ricard <christophe-h.ricard@st.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Newer Fedora and OpenSUSE didn't boot with my standard configuration.
It took me some time to figure out why, in fact I had to write a script
to try different config options systematically.

The problem is that something (systemd) in dracut depends on
CONFIG_FHANDLE, which adds open by file handle syscalls.

While it is set in defconfigs it is very easy to miss when updating
older configs because it is not default y.

Make it default y and also depend on EXPERT, as dracut use is likely
widespread.
Signed-off-by: Andi Kleen <ak@linux.intel.com>
Cc: Richard Weinberger <richard.weinberger@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit fea85cff ("mm/page_isolation.c: return last tested pfn rather
than failure indicator") changed the meaning of the return value.  Let's
change the function comments as well.
Signed-off-by: Neil Zhang <neilzhang1123@hotmail.com>
Cc: Joonsoo Kim <js1304@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit bb29902a ("oom, oom_reaper: protect oom_reaper_list using
simpler way") has simplified the check for tasks already enqueued for
the oom reaper by checking tsk->oom_reaper_list != NULL.  This check is
not sufficient because the tsk might be the head of the queue without
any other tasks queued and then we would simply lockup looping on the
same task.  Fix the condition by checking for the head as well.

Fixes: bb29902a ("oom, oom_reaper: protect oom_reaper_list using simpler way")
Signed-off-by: Michal Hocko <mhocko@suse.com>
Acked-by: Tetsuo Handa <penguin-kernel@I-love.SAKURA.ne.jp>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Page isolation has not failed if the fin pfn extends beyond the end pfn
and test_pages_isolated checks this correctly.  Fix the tracepoint to
report the same result as the actual check function.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Joonsoo Kim <js1304@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The recently introduced batched invalidations mechanism uses its own
mechanism for shootdown.  However, it does wrong accounting of
interrupts (e.g., inc_irq_stat is called for local invalidations),
trace-points (e.g., TLB_REMOTE_SHOOTDOWN for local invalidations) and
may break some platforms as it bypasses the invalidation mechanisms of
Xen and SGI UV.

This patch reuses the existing TLB flushing mechnaisms instead.  We use
NULL as mm to indicate a global invalidation is required.

Fixes 72b252ae ("mm: send one IPI per CPU to TLB flush all entries after unmapping pages")
Signed-off-by: Nadav Amit <namit@vmware.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

TLB_REMOTE_SEND_IPI was recently introduced, but it counts bytes instead
of pages.  In addition, it does not report correctly the case in which
flush_tlb_page flushes a page.  Fix it to be consistent with other TLB
counters.

Fixes: 5b74283a ("x86, mm: trace when an IPI is about to be sent")
Signed-off-by: Nadav Amit <namit@vmware.com>
Cc: Mel Gorman <mgorman@suse.de>
Cc: Rik van Riel <riel@redhat.com>
Cc: Dave Hansen <dave.hansen@intel.com>
Cc: Ingo Molnar <mingo@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

It is incorrect to use next_node to find a target node, it will return
MAX_NUMNODES or invalid node.  This will lead to crash in buddy system
allocation.

Fixes: c8721bbb ("mm: memory-hotplug: enable memory hotplug to handle hugepage")
Signed-off-by: Xishi Qiu <qiuxishi@huawei.com>
Acked-by: Vlastimil Babka <vbabka@suse.cz>
Acked-by: Naoya Horiguchi <n-horiguchi@ah.jp.nec.com>
Cc: Joonsoo Kim <js1304@gmail.com>
Cc: David Rientjes <rientjes@google.com>
Cc: "Laura Abbott" <lauraa@codeaurora.org>
Cc: Hui Zhu <zhuhui@xiaomi.com>
Cc: Wang Xiaoqiang <wangxq10@lzu.edu.cn>
Cc: <stable@vger.kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

The return value of pmd_trans_huge_lock() is a pointer, not a boolean
value, so use NULL instead of false as the return value.
Signed-off-by: Chen Gang <gang.chen.5i5j@gmail.com>
Acked-by: Kirill A. Shutemov <kirill.shutemov@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Add the missing argument to set_track().

Fixes: cd11016e ("mm, kasan: stackdepot implementation. Enable stackdepot for SLAB")
Signed-off-by: Alexander Potapenko <glider@google.com>
Cc: Andrey Konovalov <adech.fo@gmail.com>
Cc: Christoph Lameter <cl@linux.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Andrey Ryabinin <ryabinin.a.a@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Joonsoo Kim <iamjoonsoo.kim@lge.com>
Cc: Konstantin Serebryany <kcc@google.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

So update MAINTAINERS to say so.
Signed-off-by: Joe Perches <joe@perches.com>
Cc: Mike Marshall <hubcap@omnibond.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

After enabling per-cpu processing it appeared that under heavy load
changing MTU can result in blocking all port's interrupts and
transmitting data is not possible after the change.

This commit fixes above issue by disabling percpu interrupts for the
time, when TXQs and RXQs are reconfigured.
Signed-off-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Giuseppe Cavallaro says:

====================
stmmac MDIO and normal descr fixes

This patch series is to fix the problems below and recently debugged
in this mailing list:

o to fix a problem for the HW where the normal descriptor
o to fix the mdio registration according to the different
  platform configurations

I am resending all the patches again: built on top of net.git repo.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Initially the phy_bus_name was added to manipulate the
driver name but it was recently just used to manage the
fixed-link and then to take some decision at run-time.
So the patch uses the is_pseudo_fixed_link and removes
the phy_bus_name variable not necessary anymore.

The driver can manage the mdio registration by using phy-handle,
dwmac-mdio and own parameter e.g. snps,phy-addr.
This patch takes care about all these possible configurations
and fixes the mdio registration in case of there is a real
transceiver or a switch (that needs to be managed by using
fixed-link).
Signed-off-by: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Tested-by: Frank Schäfer <fschaefer.oss@googlemail.com>
Cc: Gabriel Fernandez <gabriel.fernandez@linaro.org>
Cc: Dinh Nguyen <dinh.linux@gmail.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Phil Reid <preid@electromag.com.au>
Signed-off-by: David S. Miller <davem@davemloft.net>