- 23 Apr, 2020 2 commits
-
-
Wen Gong authored
sdio chip use DMA buffer to receive TX packet from ath10k, and it has limitation of each buffer, if the packet size exceed the credit size, it will trigger error in firmware. Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00017-QCARMSWP-1. Signed-off-by:
Wen Gong <wgong@codeaurora.org> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org> Link: https://lore.kernel.org/r/20200422084719.3479-1-wgong@codeaurora.org
-
Maharaja Kennadyrajan authored
The driver is allowing the invalid tx/rx chainmask configuration (other than 1,3,7,15) set by the user. It causes the firmware crash due to the invalid chainmask values. Hence, reject the invalid chainmask values in the driver by not sending the pdev set command to the firmware. Tested hardware: QCA9888 Tested firmware: 10.4-3.10-00047 Signed-off-by:
Maharaja Kennadyrajan <mkenna@codeaurora.org> Signed-off-by:
-
- 22 Apr, 2020 5 commits
-
-
Wen Gong authored
When station connected to AP, and run TX traffic such as TCP/UDP, and system enter suspend state, then mac80211 call ath10k_flush with set drop flag, recently it only send wmi peer flush to firmware and firmware will flush all pending TX packets, for PCIe, firmware will indicate the TX packets status to ath10k, and then ath10k indicate to mac80211 TX complete with the status, then all the packets has been flushed at this moment. For SDIO chip, it is different, its TX complete indication is disabled by default, and it has a tx queue in ath10k, and its tx credit control is enabled, total tx credit is 96, when its credit is not sufficient, then the packets will buffered in the tx queue of ath10k, max packets is TARGET_TLV_NUM_MSDU_DESC_HL which is 1024, for SDIO, when mac80211 call ath10k_flush with set drop flag, maybe it have pending packets in tx queue of ath10k, and if it does not have sufficient tx credit, the packets will stay in queue untill tx credit report from firmware, if it is a noisy environment, tx speed is low and the tx credit report from firmware will delay more time, then the num_pending_tx will remain > 0 untill all packets send to firmware. After the 1st ath10k_flush, mac80211 will call the 2nd ath10k_flush without set drop flag immediately, then it will call to ath10k_mac_wait_tx_complete, and it wait untill num_pending_tx become to 0, in noisy environment, it is esay to wait about near 5 seconds, then it cause the suspend take long time. 1st and 2nd callstack of ath10k_flush [ 303.740427] ath10k_sdio mmc1:0001:1: ath10k_flush drop:1, pending:0-0 [ 303.740495] ------------[ cut here ]------------ [ 303.740739] WARNING: CPU: 1 PID: 3921 at /mnt/host/source/src/third_party/kernel/v4.19/drivers/net/wireless/ath/ath10k/mac.c:7025 ath10k_flush+0x54/0x104 [ath10k_core] [ 303.740757] Modules linked in: bridge stp llc ath10k_sdio ath10k_core rfcomm uinput cros_ec_rpmsg mtk_seninf mtk_cam_isp mtk_vcodec_enc mtk_fd mtk_vcodec_dec mtk_vcodec_common mtk_dip mtk_mdp3 videobuf2_dma_contig videobuf2_memops v4l2_mem2mem videobuf2_v4l2 videobuf2_common hid_google_hammer hci_uart btqca bluetooth dw9768 ov8856 ecdh_generic ov02a10 v4l2_fwnode mtk_scp mtk_rpmsg rpmsg_core mtk_scp_ipi ipt_MASQUERADE fuse iio_trig_sysfs cros_ec_sensors_ring cros_ec_sensors_sync cros_ec_light_prox cros_ec_sensors industrialio_triggered_buffer [ 303.740914] kfifo_buf cros_ec_activity cros_ec_sensors_core lzo_rle lzo_compress ath mac80211 zram cfg80211 joydev [last unloaded: ath10k_core] [ 303.741009] CPU: 1 PID: 3921 Comm: kworker/u16:10 Tainted: G W 4.19.95 #2 [ 303.741027] Hardware name: MediaTek krane sku176 board (DT) [ 303.741061] Workqueue: events_unbound async_run_entry_fn [ 303.741086] pstate: 60000005 (nZCv daif -PAN -UAO) [ 303.741166] pc : ath10k_flush+0x54/0x104 [ath10k_core] [ 303.741244] lr : ath10k_flush+0x54/0x104 [ath10k_core] [ 303.741260] sp : ffffffdf080e77a0 [ 303.741276] x29: ffffffdf080e77a0 x28: ffffffdef3730040 [ 303.741300] x27: ffffff907c2240a0 x26: ffffffde6ff39afc [ 303.741321] x25: ffffffdef3730040 x24: ffffff907bf61018 [ 303.741343] x23: ffffff907c2240a0 x22: ffffffde6ff39a50 [ 303.741364] x21: 0000000000000001 x20: ffffffde6ff39a50 [ 303.741385] x19: ffffffde6bac2420 x18: 0000000000017200 [ 303.741407] x17: ffffff907c24a000 x16: 0000000000000037 [ 303.741428] x15: ffffff907b49a568 x14: ffffff907cf332c1 [ 303.741476] x13: 00000000000922e4 x12: 0000000000000000 [ 303.741497] x11: 0000000000000001 x10: 0000000000000007 [ 303.741518] x9 : f2256b8c1de4bc00 x8 : f2256b8c1de4bc00 [ 303.741539] x7 : ffffff907ab5e764 x6 : 0000000000000000 [ 303.741560] x5 : 0000000000000080 x4 : 0000000000000001 [ 303.741582] x3 : ffffffdf080e74a8 x2 : ffffff907aa91244 [ 303.741603] x1 : ffffffdf080e74a8 x0 : 0000000000000024 [ 303.741624] Call trace: [ 303.741701] ath10k_flush+0x54/0x104 [ath10k_core] [ 303.741941] __ieee80211_flush_queues+0x1dc/0x358 [mac80211] [ 303.742098] ieee80211_flush_queues+0x34/0x44 [mac80211] [ 303.742253] ieee80211_set_disassoc+0xc0/0x5ec [mac80211] [ 303.742399] ieee80211_mgd_deauth+0x720/0x7d4 [mac80211] [ 303.742535] ieee80211_deauth+0x24/0x30 [mac80211] [ 303.742720] cfg80211_mlme_deauth+0x250/0x3bc [cfg80211] [ 303.742849] cfg80211_mlme_down+0x90/0xd0 [cfg80211] [ 303.742971] cfg80211_disconnect+0x340/0x3a0 [cfg80211] [ 303.743087] __cfg80211_leave+0xe4/0x17c [cfg80211] [ 303.743203] cfg80211_leave+0x38/0x50 [cfg80211] [ 303.743319] wiphy_suspend+0x84/0x5bc [cfg80211] [ 303.743335] dpm_run_callback+0x170/0x304 [ 303.743346] __device_suspend+0x2dc/0x3e8 [ 303.743356] async_suspend+0x2c/0xb0 [ 303.743370] async_run_entry_fn+0x48/0xf8 [ 303.743383] process_one_work+0x304/0x604 [ 303.743394] worker_thread+0x248/0x3f4 [ 303.743403] kthread+0x120/0x130 [ 303.743416] ret_from_fork+0x10/0x18 [ 303.743812] ath10k_sdio mmc1:0001:1: ath10k_flush drop:0, pending:0-0 [ 303.743858] ------------[ cut here ]------------ [ 303.744057] WARNING: CPU: 1 PID: 3921 at /mnt/host/source/src/third_party/kernel/v4.19/drivers/net/wireless/ath/ath10k/mac.c:7025 ath10k_flush+0x54/0x104 [ath10k_core] [ 303.744075] Modules linked in: bridge stp llc ath10k_sdio ath10k_core rfcomm uinput cros_ec_rpmsg mtk_seninf mtk_cam_isp mtk_vcodec_enc mtk_fd mtk_vcodec_dec mtk_vcodec_common mtk_dip mtk_mdp3 videobuf2_dma_contig videobuf2_memops v4l2_mem2mem videobuf2_v4l2 videobuf2_common hid_google_hammer hci_uart btqca bluetooth dw9768 ov8856 ecdh_generic ov02a10 v4l2_fwnode mtk_scp mtk_rpmsg rpmsg_core mtk_scp_ipi ipt_MASQUERADE fuse iio_trig_sysfs cros_ec_sensors_ring cros_ec_sensors_sync cros_ec_light_prox cros_ec_sensors industrialio_triggered_buffer kfifo_buf cros_ec_activity cros_ec_sensors_core lzo_rle lzo_compress ath mac80211 zram cfg80211 joydev [last unloaded: ath10k_core] [ 303.744256] CPU: 1 PID: 3921 Comm: kworker/u16:10 Tainted: G W 4.19.95 #2 [ 303.744273] Hardware name: MediaTek krane sku176 board (DT) [ 303.744301] Workqueue: events_unbound async_run_entry_fn [ 303.744325] pstate: 60000005 (nZCv daif -PAN -UAO) [ 303.744403] pc : ath10k_flush+0x54/0x104 [ath10k_core] [ 303.744480] lr : ath10k_flush+0x54/0x104 [ath10k_core] [ 303.744496] sp : ffffffdf080e77a0 [ 303.744512] x29: ffffffdf080e77a0 x28: ffffffdef3730040 [ 303.744534] x27: ffffff907c2240a0 x26: ffffffde6ff39afc [ 303.744556] x25: ffffffdef3730040 x24: ffffff907bf61018 [ 303.744577] x23: ffffff907c2240a0 x22: ffffffde6ff39a50 [ 303.744598] x21: 0000000000000000 x20: ffffffde6ff39a50 [ 303.744620] x19: ffffffde6bac2420 x18: 000000000001831c [ 303.744641] x17: ffffff907c24a000 x16: 0000000000000037 [ 303.744662] x15: ffffff907b49a568 x14: ffffff907cf332c1 [ 303.744683] x13: 00000000000922ea x12: 0000000000000000 [ 303.744704] x11: 0000000000000001 x10: 0000000000000007 [ 303.744747] x9 : f2256b8c1de4bc00 x8 : f2256b8c1de4bc00 [ 303.744768] x7 : ffffff907ab5e764 x6 : 0000000000000000 [ 303.744789] x5 : 0000000000000080 x4 : 0000000000000001 [ 303.744810] x3 : ffffffdf080e74a8 x2 : ffffff907aa91244 [ 303.744831] x1 : ffffffdf080e74a8 x0 : 0000000000000024 [ 303.744853] Call trace: [ 303.744929] ath10k_flush+0x54/0x104 [ath10k_core] [ 303.745098] __ieee80211_flush_queues+0x1dc/0x358 [mac80211] [ 303.745277] ieee80211_flush_queues+0x34/0x44 [mac80211] [ 303.745424] ieee80211_set_disassoc+0x108/0x5ec [mac80211] [ 303.745569] ieee80211_mgd_deauth+0x720/0x7d4 [mac80211] [ 303.745706] ieee80211_deauth+0x24/0x30 [mac80211] [ 303.745853] cfg80211_mlme_deauth+0x250/0x3bc [cfg80211] [ 303.745979] cfg80211_mlme_down+0x90/0xd0 [cfg80211] [ 303.746103] cfg80211_disconnect+0x340/0x3a0 [cfg80211] [ 303.746219] __cfg80211_leave+0xe4/0x17c [cfg80211] [ 303.746335] cfg80211_leave+0x38/0x50 [cfg80211] [ 303.746452] wiphy_suspend+0x84/0x5bc [cfg80211] [ 303.746467] dpm_run_callback+0x170/0x304 [ 303.746477] __device_suspend+0x2dc/0x3e8 [ 303.746487] async_suspend+0x2c/0xb0 [ 303.746498] async_run_entry_fn+0x48/0xf8 [ 303.746510] process_one_work+0x304/0x604 [ 303.746521] worker_thread+0x248/0x3f4 [ 303.746530] kthread+0x120/0x130 [ 303.746542] ret_from_fork+0x10/0x18 one sample's debugging log: it wait 3190 ms(5000 - 1810). 1st ath10k_flush, it has 120 packets in tx queue of ath10k: <...>-1513 [000] .... 25374.786005: ath10k_log_err: ath10k_sdio mmc1:0001:1 ath10k_flush drop:1, pending:120-0 <...>-1513 [000] ...1 25374.788375: ath10k_log_warn: ath10k_sdio mmc1:0001:1 ath10k_htt_tx_mgmt_inc_pending htt->num_pending_mgmt_tx:0 <...>-1500 [001] .... 25374.790143: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx work, eid:1, count:121 2st ath10k_flush, it has 121 packets in tx queue of ath10k: <...>-1513 [000] .... 25374.790571: ath10k_log_err: ath10k_sdio mmc1:0001:1 ath10k_flush drop:0, pending:121-0 <...>-1513 [000] .... 25374.791990: ath10k_log_err: ath10k_sdio mmc1:0001:1 ath10k_mac_wait_tx_complete state:1 pending:121-0 <...>-1508 [001] .... 25374.792696: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 credit update: delta:46 <...>-1508 [001] .... 25374.792700: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 credit total:46 <...>-1508 [001] .... 25374.792729: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx work, eid:1, count:121 <...>-1508 [001] .... 25374.792937: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx status:0, eid:1, req count:88, count:32, len:49792 <...>-1508 [001] .... 25374.793031: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx status:0, eid:1, req count:75, count:14, len:21784 kworker/u16:0-25773 [003] .... 25374.793701: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx complete, eid:1, pending complete count:46 <...>-1881 [000] .... 25375.073178: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 credit update: delta:24 <...>-1881 [000] .... 25375.073182: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 credit total:24 <...>-1881 [000] .... 25375.073429: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx work, eid:1, count:75 <...>-1879 [001] .... 25375.074090: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx complete, eid:1, pending complete count:24 <...>-1881 [000] .... 25375.074123: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx status:0, eid:1, req count:51, count:24, len:37344 <...>-1879 [001] .... 25375.270126: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 credit update: delta:26 <...>-1879 [001] .... 25375.270130: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 credit total:26 <...>-1488 [000] .... 25375.270174: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx work, eid:1, count:51 <...>-1488 [000] .... 25375.270529: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx status:0, eid:1, req count:25, count:26, len:40456 <...>-1879 [001] .... 25375.270693: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx complete, eid:1, pending complete count:26 <...>-1488 [001] .... 25377.775885: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 credit update: delta:12 <...>-1488 [001] .... 25377.775890: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 credit total:12 <...>-1488 [001] .... 25377.775933: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx work, eid:1, count:25 <...>-1488 [001] .... 25377.776059: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx status:0, eid:1, req count:13, count:12, len:18672 <...>-1879 [001] .... 25377.776100: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx complete, eid:1, pending complete count:12 <...>-1488 [001] .... 25377.878079: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 credit update: delta:15 <...>-1488 [001] .... 25377.878087: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 credit total:15 <...>-1879 [000] .... 25377.878323: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx work, eid:1, count:13 <...>-1879 [000] .... 25377.878487: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx status:0, eid:1, req count:0, count:13, len:20228 <...>-1879 [000] .... 25377.878497: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx complete, eid:1, pending complete count:13 <...>-1488 [001] .... 25377.919927: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 credit update: delta:11 <...>-1488 [001] .... 25377.919932: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 credit total:13 <...>-1488 [001] .... 25377.919976: ath10k_log_dbg: ath10k_sdio mmc1:0001:1 bundle tx work, eid:1, count:0 <...>-1881 [000] .... 25377.982645: ath10k_log_warn: ath10k_sdio mmc1:0001:1 HTT_T2H_MSG_TYPE_MGMT_TX_COMPLETION status:0 <...>-1513 [001] .... 25377.982973: ath10k_log_err: ath10k_sdio mmc1:0001:1 ath10k_mac_wait_tx_complete time_left:1810, pending:0-0 Flush all pending TX packets for the 1st ath10k_flush reduced the wait time of the 2nd ath10k_flush and then suspend take short time. This Patch only effect SDIO chips. Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00042. Signed-off-by:
-
Wen Gong authored
The default credit size is 1792 bytes, but the IP mtu is 1500 bytes, then it has about 290 bytes's waste for each data packet on sdio transfer path for TX bundle, it will reduce the transmission utilization ratio for data packet. This patch enable the small credit size in firmware, firmware will use the new credit size 1556 bytes, it will increase the transmission utilization ratio for data packet on TX patch. It results in significant performance improvement on TX path. This patch only effect sdio chip, it will not effect PCI, SNOC etc. Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00017-QCARMSWP-1. Signed-off-by:
-
Wen Gong authored
The transmission utilization ratio for sdio bus for small packet is slow, because the space and time cost for sdio bus is same for large length packet and small length packet. So the speed of data for large length packet is higher than small length. Test result of different length of data: data packet(byte) cost time(us) calculated rate(Mbps) 256 28 73 512 33 124 1024 35 234 1792 45 318 14336 168 682 28672 333 688 57344 660 695 This patch change the TX packet from single packet to a large length bundle packet, max size is 32, it results in significant performance improvement on TX path. Also there's a fourth thread "ath10k_tx_complete_wq" added to ath10k as it improves TCP RX throughput (values in Mbps): TCP-RX TCP-TX UDP-RX UDP-TX use workqueue_tx_complete 423 357 448 412 change it to ar->workqueue 410 360 449 414 change it to ar->workqueue_aux 405 339 446 401 This patch only effect sdio chip, it will not effect PCI, SNOC etc. It only enable bundle for sdio chip. Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00017-QCARMSWP-1. Signed-off-by: -
Jason Yan authored
The '==' expression itself is bool, no need to convert it to bool again. This fixes the following coccicheck warning: drivers/net/wireless/ath/ath11k/debug.c:198:57-62: WARNING: conversion to bool not needed here drivers/net/wireless/ath/ath11k/debug.c:218:58-63: WARNING: conversion to bool not needed here Signed-off-by:
Jason Yan <yanaijie@huawei.com> Signed-off-by:
-
Jason Yan authored
The '==' expression itself is bool, no need to convert it to bool again. This fixes the following coccicheck warning: drivers/net/wireless/ath/ath11k/dp_rx.c:255:46-51: WARNING: conversion to bool not needed here Signed-off-by:
-
- 21 Apr, 2020 4 commits
-
-
Kalle Valo authored
That way we don't need to have an empty function in sdio.c. No functional changes, compile tested only. Signed-off-by:
-
Kalle Valo authored
The _hif_ prefix should be used only on functions part of ath10k_hif_ops, so remove it from functions which should not have it. No functional changes, compile tested only. Signed-off-by:
-
Wen Gong authored
This patch is to set register to allow the mbox enter sleep status if it does not have tx traffic and wakeup it if tx traffic arrive. After mbox enter sleep status, the soc will enter sleep status by firmware, this will save power. The power consume drops from about 90mW to about 10mW with this patch. This patch only effect sdio chip. Tested with QCA6174 SDIO with firmware WLAN.RMH.4.4.1-00029. Signed-off-by:
-
Kalle Valo authored
Convert ath10k_hif_swap_mailbox() to a more generic op so that bus drivers can do more than just swap the mailbox, for example set power save settings like in the following sdio patch. No functional changes, compile tested only. Signed-off-by:
-
- 15 Apr, 2020 6 commits
-
-
Sriram R authored
IPQ8074 HW supports three TCL rings for tx. Currently these rings are mapped based on the Access categories, viz. VO, VI, BE, BK. In case, one of the traffic type dominates, then it could stress the same tcl rings. Rather, it would be optimal to make use of all the rings in a round robin fashion irrespective of the traffic type so that the load could be evenly distributed among all the rings. Also, in case the selected ring is busy or full, a retry mechanism is used to ensure other available ring is selected without dropping the packet. In SMP systems, this change avoids a single CPU from getting hogged when heavy traffic of same category is transmitted. The tx completion interrupts corresponding to the used tcl ring would be more which causes the assigned CPU to get hogged. Distribution of tx packets to different tcl rings helps balance this load. Signed-off-by:
Sriram R <srirrama@codeaurora.org> Signed-off-by:
-
Govindaraj Saminathan authored
should not overwrite the error code. No buffer available then return invalid. For other failures return the error code of actual failure. Signed-off-by:
Govindaraj Saminathan <gsamin@codeaurora.org> Signed-off-by:
-
Mamatha Telu authored
Fix some typo: s/fnrom/from s/pkgs/pkts/ s/AMSUs/AMSDUs/ Signed-off-by:
Mamatha Telu <telumamatha36@gmail.com> Signed-off-by:
-
Maharaja Kennadyrajan authored
Rx_filter flags are set with default filter flags during wifi up/down sequence even though the 'ext_rx_stats' debugfs is enabled as 1. So, that we are not getting proper per peer rx_stats. Hence, fixing this by setting the missing rx_filter when ext_rx_stats is already set/enabled. Signed-off-by:
-
Ritesh Singh authored
After setting fixed vht-rate if new station is trying to assoc with mu_bfee cap, or if a sta is already connected with mu_bfee cap then set the fixed vht-rate and reconnecting the sta, FW assert is happening. So to avoid this, reset the MU_BEAMFORMEE bit in vht->caps, if mcs_index is invalid for nss 1. Signed-off-by:
Ritesh Singh <ritesi@codeaurora.org> Signed-off-by:
-
Maharaja Kennadyrajan authored
Debugfs pdev entries should be cleaned up during the crash on recovery. If not, mac register will fail for the reason that it is already registered during core reconfigure. Signed-off-by:
-
- 14 Apr, 2020 6 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/ath.gitKalle Valo authored
ath.git patches for v5.8. Major changes: ath11k * add debugfs file for testing ADDBA and DELBA ath10k * enable VHT160 and VHT80+80 modes * enable radar detection in secondary segment * sdio: disable TX complete indication to improve throughput
-
Manikanta Pubbisetty authored
During RX, accessing the reo dest ring descriptor directly is consuming a lot of CPU cycles. Accessing the descriptor after copying it locally has improved CPU usage by around ~10-15% while measuring throughput in RX DBTC test cases(all radios are involved in the throughput measurement). HW tested: IPQ8074 Signed-off-by:
Manikanta Pubbisetty <mpubbise@codeaurora.org> Signed-off-by:
-
Manikanta Pubbisetty authored
Unlike CE interrupts, DP interrupts are not enabled/disabled at source; they are enabled/disabled only at GIC level, therefore it is required to set IRQ_DISABLE_UNLAZY flag to avoid spurious interrupts. Signed-off-by:
-
Aloka Dixit authored
TWT feature fails on radio2 because physical device count is hardcoded to 2. Set value dynamically. Signed-off-by:
Aloka Dixit <alokad@codeaurora.org> Signed-off-by:
-
Karthikeyan Periyasamy authored
Modify the interrupt timer threshold param as 256 to avoid HW watchdog in heavy multicast traffic scenario. Signed-off-by:
Karthikeyan Periyasamy <periyasa@codeaurora.org> Signed-off-by:
-
Karthikeyan Periyasamy authored
Add the pdev index information in the peer object to validate the peer creation. Ignore the peer creation request, if the given MAC address is already present in the peer list with same radio. If we allow the peer creation in above scenario, FW assert will happen. Above scenario occurred in two cases, where Multiple AP VAP created in the same radio. 1. when testing tool sends association request to two AP with same MAC address 2. when a station do roaming from one AP VAP to another AP VAP. Signed-off-by:
-
- 12 Apr, 2020 10 commits
-
-
Linus Torvalds authored
-
Linus Torvalds authored
This sorts the actual field names too, potentially causing even more chaos and confusion at merge time if you have edited the MAINTAINERS file. But the end result is a more consistent layout, and hopefully it's a one-time pain minimized by doing this just before the -rc1 release. This was entirely scripted: ./scripts/parse-maintainers.pl --input=MAINTAINERS --output=MAINTAINERS --order Requested-by:
Joe Perches <joe@perches.com> Signed-off-by:
Linus Torvalds <torvalds@linux-foundation.org>
-
Linus Torvalds authored
They are all supposed to be sorted, but people who add new entries don't always know the alphabet. Plus sometimes the entry names get edited, and people don't then re-order the entry. Let's see how painful this will be for merging purposes (the MAINTAINERS file is often edited in various different trees), but Joe claims there's relatively few patches in -next that touch this, and doing it just before -rc1 is likely the best time. Fingers crossed. This was scripted with /scripts/parse-maintainers.pl --input=MAINTAINERS --output=MAINTAINERS but then I also ended up manually upper-casing a few entry names that stood out when looking at the end result. Requested-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull x86 fixes from Thomas Gleixner: "A set of three patches to fix the fallout of the newly added split lock detection feature. It addressed the case where a KVM guest triggers a split lock #AC and KVM reinjects it into the guest which is not prepared to handle it. Add proper sanity checks which prevent the unconditional injection into the guest and handles the #AC on the host side in the same way as user space detections are handled. Depending on the detection mode it either warns and disables detection for the task or kills the task if the mode is set to fatal" * tag 'x86-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: KVM: VMX: Extend VMXs #AC interceptor to handle split lock #AC in guest KVM: x86: Emulate split-lock access as a write in emulator x86/split_lock: Provide handle_guest_split_lock()
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull time(keeping) updates from Thomas Gleixner: - Fix the time_for_children symlink in /proc/$PID/ so it properly reflects that it part of the 'time' namespace - Add the missing userns limit for the allowed number of time namespaces, which was half defined but the actual array member was not added. This went unnoticed as the array has an exessive empty member at the end but introduced a user visible regression as the output was corrupted. - Prevent further silent ucount corruption by adding a BUILD_BUG_ON() to catch half updated data. * tag 'timers-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: ucount: Make sure ucounts in /proc/sys/user don't regress again time/namespace: Add max_time_namespaces ucount time/namespace: Fix time_for_children symlink
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull scheduler fixes/updates from Thomas Gleixner: - Deduplicate the average computations in the scheduler core and the fair class code. - Fix a raise between runtime distribution and assignement which can cause exceeding the quota by up to 70%. - Prevent negative results in the imbalanace calculation - Remove a stale warning in the workqueue code which can be triggered since the call site was moved out of preempt disabled code. It's a false positive. - Deduplicate the print macros for procfs - Add the ucmap values to the SCHED_DEBUG procfs output for completness * tag 'sched-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: sched/debug: Add task uclamp values to SCHED_DEBUG procfs sched/debug: Factor out printing formats into common macros sched/debug: Remove redundant macro define sched/core: Remove unused rq::last_load_update_tick workqueue: Remove the warning in wq_worker_sleeping() sched/fair: Fix negative imbalance in imbalance calculation sched/fair: Fix race between runtime distribution and assignment sched/fair: Align rq->avg_idle and rq->avg_scan_cost
-
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull perf fixes from Thomas Gleixner: "Three fixes/updates for perf: - Fix the perf event cgroup tracking which tries to track the cgroup even for disabled events. - Add Ice Lake server support for uncore events - Disable pagefaults when retrieving the physical address in the sampling code" * tag 'perf-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: perf/core: Disable page faults when getting phys address perf/x86/intel/uncore: Add Ice Lake server uncore support perf/cgroup: Correct indirection in perf_less_group_idx() perf/core: Fix event cgroup tracking -
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tipLinus Torvalds authored
Pull locking fixes from Thomas Gleixner: "Three small fixes/updates for the locking core code: - Plug a task struct reference leak in the percpu rswem implementation. - Document the refcount interaction with PID_MAX_LIMIT - Improve the 'invalid wait context' data dump in lockdep so it contains all information which is required to decode the problem" * tag 'locking-urgent-2020-04-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: locking/lockdep: Improve 'invalid wait context' splat locking/refcount: Document interaction with PID_MAX_LIMIT locking/percpu-rwsem: Fix a task_struct refcount -
git://git.samba.org/sfrench/cifs-2.6Linus Torvalds authored
Pull cifs fixes from Steve French: "Ten cifs/smb fixes: - five RDMA (smbdirect) related fixes - add experimental support for swap over SMB3 mounts - also a fix which improves performance of signed connections" * tag '5.7-rc-smb3-fixes-part2' of git://git.samba.org/sfrench/cifs-2.6: smb3: enable swap on SMB3 mounts smb3: change noisy error message to FYI smb3: smbdirect support can be configured by default cifs: smbd: Do not schedule work to send immediate packet on every receive cifs: smbd: Properly process errors on ib_post_send cifs: Allocate crypto structures on the fly for calculating signatures of incoming packets cifs: smbd: Update receive credits before sending and deal with credits roll back on failure before sending cifs: smbd: Check send queue size before posting a send cifs: smbd: Merge code to track pending packets cifs: ignore cached share root handle closing errors
-
git://git.linux-nfs.org/projects/trondmy/linux-nfsLinus Torvalds authored
Pull NFS client bugfix from Trond Myklebust: "Fix an RCU read lock leakage in pnfs_alloc_ds_commits_list()" * tag 'nfs-for-5.7-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs: pNFS: Fix RCU lock leakage
-
- 11 Apr, 2020 7 commits
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/lftan/nios2Linus Torvalds authored
Pull nios2 updates from Ley Foon Tan: - Remove nios2-dev@lists.rocketboards.org from MAINTAINERS - remove 'resetvalue' property - rename 'altr,gpio-bank-width' -> 'altr,ngpio' - enable the common clk subsystem on Nios2 * tag 'nios2-v5.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/lftan/nios2: MAINTAINERS: Remove nios2-dev@lists.rocketboards.org arch: nios2: remove 'resetvalue' property arch: nios2: rename 'altr,gpio-bank-width' -> 'altr,ngpio' arch: nios2: Enable the common clk subsystem on Nios2
-
git://git.infradead.org/users/hch/dma-mappingLinus Torvalds authored
Pull dma-mapping fixes from Christoph Hellwig: - fix an integer truncation in dma_direct_get_required_mask (Kishon Vijay Abraham) - fix the display of dma mapping types (Grygorii Strashko) * tag 'dma-mapping-5.7-1' of git://git.infradead.org/users/hch/dma-mapping: dma-debug: fix displaying of dma allocation type dma-direct: fix data truncation in dma_direct_get_required_mask()
-
git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuildLinus Torvalds authored
Pull more Kbuild updates from Masahiro Yamada: - raise minimum supported binutils version to 2.23 - remove old CONFIG_AS_* macros that we know binutils >= 2.23 supports - move remaining CONFIG_AS_* tests to Kconfig from Makefile - enable -Wtautological-compare warnings to catch more issues - do not support GCC plugins for GCC <= 4.7 - fix various breakages of 'make xconfig' - include the linker version used for linking the kernel into LINUX_COMPILER, which is used for the banner, and also exposed to /proc/version - link lib-y objects to vmlinux forcibly when CONFIG_MODULES=y, which allows us to remove the lib-ksyms.o workaround, and to solve the last known issue of the LLVM linker - add dummy tools in scripts/dummy-tools/ to enable all compiler tests in Kconfig, which will be useful for distro maintainers - support the single switch, LLVM=1 to use Clang and all LLVM utilities instead of GCC and Binutils. - support LLVM_IAS=1 to enable the integrated assembler, which is still experimental * tag 'kbuild-v5.7-2' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild: (36 commits) kbuild: fix comment about missing include guard detection kbuild: support LLVM=1 to switch the default tools to Clang/LLVM kbuild: replace AS=clang with LLVM_IAS=1 kbuild: add dummy toolchains to enable all cc-option etc. in Kconfig kbuild: link lib-y objects to vmlinux forcibly when CONFIG_MODULES=y MIPS: fw: arc: add __weak to prom_meminit and prom_free_prom_memory kbuild: remove -I$(srctree)/tools/include from scripts/Makefile kbuild: do not pass $(KBUILD_CFLAGS) to scripts/mkcompile_h Documentation/llvm: fix the name of llvm-size kbuild: mkcompile_h: Include $LD version in /proc/version kconfig: qconf: Fix a few alignment issues kconfig: qconf: remove some old bogus TODOs kconfig: qconf: fix support for the split view mode kconfig: qconf: fix the content of the main widget kconfig: qconf: Change title for the item window kconfig: qconf: clean deprecated warnings gcc-plugins: drop support for GCC <= 4.7 kbuild: Enable -Wtautological-compare x86: update AS_* macros to binutils >=2.23, supporting ADX and AVX2 crypto: x86 - clean up poly1305-x86_64-cryptogams.S by 'make clean' ...
-
Sedat Dilek authored
I do not longer work for credativ Germany. Please, use my private email address instead. This is for the case when people want to CC me on patches sent from my old business email address. Signed-off-by:
Sedat Dilek <sedat.dilek@gmail.com> Signed-off-by:
-
Trond Myklebust authored
Another brown paper bag moment. pnfs_alloc_ds_commits_list() is leaking the RCU lock. Fixes: a9901899 ("pNFS: Add infrastructure for cleaning up per-layout commit structures") Signed-off-by:
Trond Myklebust <trond.myklebust@hammerspace.com>
-
Xiaoyao Li authored
Two types of #AC can be generated in Intel CPUs: 1. legacy alignment check #AC 2. split lock #AC Reflect #AC back into the guest if the guest has legacy alignment checks enabled or if split lock detection is disabled. If the #AC is not a legacy one and split lock detection is enabled, then invoke handle_guest_split_lock() which will either warn and disable split lock detection for this task or force SIGBUS on it. [ tglx: Switch it to handle_guest_split_lock() and rename the misnamed helper function. ] Suggested-by:
Sean Christopherson <sean.j.christopherson@intel.com> Signed-off-by:
Xiaoyao Li <xiaoyao.li@intel.com> Signed-off-by:
Thomas Gleixner <tglx@linutronix.de> Signed-off-by:
Borislav Petkov <bp@suse.de> Acked-by:
Paolo Bonzini <pbonzini@redhat.com> Link: https://lkml.kernel.org/r/20200410115517.176308876@linutronix.de
-
Xiaoyao Li authored
Emulate split-lock accesses as writes if split lock detection is on to avoid #AC during emulation, which will result in a panic(). This should never occur for a well-behaved guest, but a malicious guest can manipulate the TLB to trigger emulation of a locked instruction[1]. More discussion can be found at [2][3]. [1] https://lkml.kernel.org/r/8c5b11c9-58df-38e7-a514-dc12d687b198@redhat.com [2] https://lkml.kernel.org/r/20200131200134.GD18946@linux.intel.com [3] https://lkml.kernel.org/r/20200227001117.GX9940@linux.intel.comSuggested-by:
-
