Skip to content

L
linux
Switch branch/tag
  1. 11 Jul, 2019 3 commits
  3. 10 Jul, 2019 2 commits
  5. 05 Jul, 2019 15 commits
  7. 03 Jul, 2019 2 commits
  9. 02 Jul, 2019 11 commits
  11. 20 Jun, 2019 2 commits
  13. 18 Jun, 2019 5 commits
    • Paolo Bonzini's avatar
      KVM: nVMX: shadow pin based execution controls · eceb9973
      Paolo Bonzini authored 
      The VMX_PREEMPTION_TIMER flag may be toggled frequently, though not
*very* frequently.  Since it does not affect KVM's dirty logic, e.g.
the preemption timer value is loaded from vmcs12 even if vmcs12 is
"clean", there is no need to mark vmcs12 dirty when L1 writes pin
controls, and shadowing the field achieves that.
Reviewed-by: default avatarPaolo Bonzini <pbonzini@redhat.com>
Signed-off-by: default avatarPaolo Bonzini <pbonzini@redhat.com>
      eceb9973
    • Sean Christopherson's avatar
      KVM: VMX: Leave preemption timer running when it's disabled · 804939ea
      Sean Christopherson authored 
      VMWRITEs to the major VMCS controls, pin controls included, are
deceptively expensive.  CPUs with VMCS caching (Westmere and later) also
optimize away consistency checks on VM-Entry, i.e. skip consistency
checks if the relevant fields have not changed since the last successful
VM-Entry (of the cached VMCS).  Because uops are a precious commodity,
uCode's dirty VMCS field tracking isn't as precise as software would
prefer.  Notably, writing any of the major VMCS fields effectively marks
the entire VMCS dirty, i.e. causes the next VM-Entry to perform all
consistency checks, which consumes several hundred cycles.

As it pertains to KVM, toggling PIN_BASED_VMX_PREEMPTION_TIMER more than
doubles the latency of the next VM-Entry (and again when/if the flag is
toggled back).  In a non-nested scenario, running a "standard" guest
with the preemption timer enabled, toggling the timer flag is uncommon
but not rare, e.g. roughly 1 in 10 entries.  Disabling the preemption
timer can change these numbers due to its use for "immediate exits",
even when explicitly disabled by userspace.

Nested virtualization in particular is painful, as the timer flag is set
for the majority of VM-Enters, but prepare_vmcs02() initializes vmcs02's
pin controls to *clear* the flag since its the timer's final state isn't
known until vmx_vcpu_run().  I.e. the majority of nested VM-Enters end
up unnecessarily writing pin controls *twice*.

Rather than toggle the timer flag in pin controls, set the timer value
itself to the largest allowed value to put it into a "soft disabled"
state, and ignore any spurious preemption timer exits.

Sadly, the timer is a 32-bit value and so theoretically it can fire
before the head death of the universe, i.e. spurious exits are possible.
But because KVM does *not* save the timer value on VM-Exit and because
the timer runs at a slower rate than the TSC, the maximuma timer value
is still sufficiently large for KVM's purposes.  E.g. on a modern CPU
with a timer that runs at 1/32 the frequency of a 2.4ghz constant-rate
TSC, the timer will fire after ~55 seconds of *uninterrupted* guest
execution.  In other words, spurious VM-Exits are effectively only
possible if the host is completely tickless on the logical CPU, the
guest is not using the preemption timer, and the guest is not generating
VM-Exits for any other reason.

To be safe from bad/weird hardware, disable the preemption timer if its
maximum delay is less than ten seconds.  Ten seconds is mostly arbitrary
and was selected in no small part because it's a nice round number.
For simplicity and paranoia, fall back to __kvm_request_immediate_exit()
if the preemption timer is disabled by KVM or userspace.  Previously
KVM continued to use the preemption timer to force immediate exits even
when the timer was disabled by userspace.  Now that KVM leaves the timer
running instead of truly disabling it, allow userspace to kill it
entirely in the unlikely event the timer (or KVM) malfunctions.
Signed-off-by: default avatarSean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: default avatarPaolo Bonzini <pbonzini@redhat.com>
      804939ea
    • Sean Christopherson's avatar
      KVM: VMX: Drop hv_timer_armed from 'struct loaded_vmcs' · 9d99cc49
      Sean Christopherson authored 
      ... now that it is fully redundant with the pin controls shadow.
Signed-off-by: default avatarSean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: default avatarPaolo Bonzini <pbonzini@redhat.com>
      9d99cc49
    • Sean Christopherson's avatar
      KVM: nVMX: Preset *DT exiting in vmcs02 when emulating UMIP · 469debdb
      Sean Christopherson authored 
      KVM dynamically toggles SECONDARY_EXEC_DESC to intercept (a subset of)
instructions that are subject to User-Mode Instruction Prevention, i.e.
VMCS.SECONDARY_EXEC_DESC == CR4.UMIP when emulating UMIP.  Preset the
VMCS control when preparing vmcs02 to avoid unnecessarily VMWRITEs,
e.g. KVM will clear VMCS.SECONDARY_EXEC_DESC in prepare_vmcs02_early()
and then set it in vmx_set_cr4().
Signed-off-by: default avatarSean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: default avatarPaolo Bonzini <pbonzini@redhat.com>
      469debdb
    • Sean Christopherson's avatar
      KVM: nVMX: Preserve last USE_MSR_BITMAPS when preparing vmcs02 · de0286b7
      Sean Christopherson authored 
      KVM dynamically toggles the CPU_BASED_USE_MSR_BITMAPS execution control
for nested guests based on whether or not both L0 and L1 want to pass
through the same MSRs to L2.  Preserve the last used value from vmcs02
so as to avoid multiple VMWRITEs to (re)set/(re)clear the bit on nested
VM-Entry.
Signed-off-by: default avatarSean Christopherson <sean.j.christopherson@intel.com>
Signed-off-by: default avatarPaolo Bonzini <pbonzini@redhat.com>
      de0286b7
GitLab Nexedi Edition | About GitLab | About Nexedi | 沪ICP备2021021310号-2 | 沪ICP备2021021310号-7