- 14 Mar, 2011 21 commits
-
-
Sarah Sharp authored
The xHCI driver essentially has both a USB 2.0 and a USB 3.0 roothub. So setting the HCD_USB3 bits in the hcd->driver->flags is a bit misleading. Add a new field to usb_hcd, bcdUSB. Store the result of hcd->driver->flags & HCD_MASK in it. Later, when we have the xHCI driver register the two roothubs, we'll set the usb_hcd->bcdUSB field to HCD_USB2 for the USB 2.0 roothub, and HCD_USB3 for the USB 3.0 roothub. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
-
Sarah Sharp authored
Change the bandwith_mutex in struct usb_hcd to a pointer. This will allow the pointer to be shared across usb_hcds for the upcoming work to split the xHCI driver roothub into a USB 2.0/1.1 and a USB 3.0 bus. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
-
Sarah Sharp authored
Refactor out the code in usb_add_hcd() to request the IRQ line for the HCD. This will only need to be called once for the two xHCI roothubs, so it's easier to refactor it into a function, rather than wrapping the long if-else block into another if statement. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
-
Sarah Sharp authored
Make the labels for the goto statements in usb_hcd_pci_probe() describe the cleanup they do, rather than being numbered err[1-4]. This makes it easier to add error handling later. The error handling for this function looks a little fishy, since set_hs_companion() isn't called until the very end of the function, and clear_hs_companion() is called if this function fails earlier than that. But it should be harmless to clear a NULL pointer, so leave the error handling as-is. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
-
Sarah Sharp authored
Instead of allocating space for the whole xhci_hcd structure at the end of usb_hcd, make the USB core allocate enough space for a pointer to the xhci_hcd structure. This will make it easy to share the xhci_hcd structure across the two roothubs (the USB 3.0 usb_hcd and the USB 2.0 usb_hcd). Deallocate the xhci_hcd at PCI remove time, so the hcd_priv will be deallocated after the usb_hcd is deallocated. We do this by registering a different PCI remove function that calls the usb_hcd_pci_remove() function, and then frees the xhci_hcd. usb_hcd_pci_remove() calls kput() on the usb_hcd structure, which will deallocate the memory that contains the hcd_priv pointer, but not the memory it points to. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
-
Sarah Sharp authored
Make sure to call into the USB core's link, unlink, and giveback URB functions with the usb_hcd pointer found by using urb->dev->bus. This will avoid confusion later, when the xHCI driver will deal with URBs from two separate buses (the USB 3.0 roothub and the faked USB 2.0 roothub). Assume xhci_urb_dequeue() will be called with the proper usb_hcd. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
-
Sarah Sharp authored
Commit d199c96d by Alan Stern ensured that low speed and full speed devices below a high speed hub without a transaction translator (TT) would never get enumerated. Simplify the check for a TT in the xHCI virtual device allocation to only check if the usb_device references a parent's TT. Make sure not to set the TT information on LS/FS devices directly connected to the roothub. The xHCI host doesn't really have a TT, and the host will throw an error when those virtual device TT fields are set for a device connected to the roothub. We need this check because the xHCI driver will shortly register two roothubs: a USB 2.0 roothub and a USB 3.0 roothub. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
-
Sarah Sharp authored
Make the USB 3.0 roothub registered by the USB core have a SuperSpeed Endpoint Companion Descriptor after the interrupt endpoint. All USB 3.0 devices are required to have this, and the USB 3.0 bus specification (section 10.13.1) says which values the descriptor should have. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
-
Sarah Sharp authored
In USB 3.0, there are two types of resets: a "hot" port reset and a "warm" port reset. The hot port reset is always tried first, and involves sending the reset signaling for a shorter amount of time. But sometimes devices don't respond to the hot reset, and a "Bigger Hammer" is needed. External hubs and roothubs will automatically try a warm reset when the hot reset fails, and they will set a status change bit to indicate when there is a "BH reset" change. Make sure the USB core clears that port status change bit, or we'll get lots of status change notifications on the interrupt endpoint of the USB 3.0 hub. (Side note: you may be confused why the USB 3.0 spec calls the same type of reset "warm reset" in some places and "BH reset" in other places. "BH" reset is supposed to stand for "Big Hammer" reset, but it also stands for "Brad Hosler". Brad died shortly after the USB 3.0 bus specification was started, and they decided to name the reset after him. The suggestion was made shortly before the spec was finalized, so the wording is a bit inconsistent.) Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
-
John Youn authored
Update the USB core to deal with USB 3.0 hubs. These hubs have a slightly different hub descriptor than USB 2.0 hubs, with a fixed (rather than variable length) size. Change the USB core's hub descriptor to have a union for the last fields that differ. Change the host controller drivers that access those last fields (DeviceRemovable and PortPowerCtrlMask) to use the union. Translate the new version of the hub port status field into the old version that khubd understands. (Note: we need to fix it to translate the roothub's port status once we stop converting it to USB 2.0 hub status internally.) Add new code to handle link state change status. Send out new control messages that are needed for USB 3.0 hubs, like Set Hub Depth. This patch is a modified version of the original patch submitted by John Youn. It's updated to reflect the removal of the "bitmap" #define, and change the hub descriptor accesses of a couple new host controller drivers. Signed-off-by: John Youn <johnyoun@synopsys.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com> Cc: Tony Olech <tony.olech@elandigitalsystems.com> Cc: "Robert P. J. Day" <rpjday@crashcourse.ca> Cc: Max Vozeler <mvz@vozeler.com> Cc: Tejun Heo <tj@kernel.org> Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Cc: Rodolfo Giometti <giometti@linux.it> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Anton Vorontsov <avorontsov@mvista.com> Cc: Sebastian Siewior <bigeasy@linutronix.de> Cc: Lothar Wassmann <LW@KARO-electronics.de> Cc: Olav Kongas <ok@artecdesign.ee> Cc: Martin Fuzzey <mfuzzey@gmail.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: David Brownell <dbrownell@users.sourceforge.net>
-
Sarah Sharp authored
The USB core will set hcd->state to HC_STATE_RUNNING before calling xhci_run, so there's no point in setting it twice. The USB core also doesn't pay attention to HC_STATE_RUNNING on the resume path anymore; it uses HCD_RH_RUNNING(), which looks at hcd->flags & (1U << HCD_FLAG_RH_RUNNING. Therefore, it's safe to remove the state set in xhci_bus_resume(). Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
-
Sarah Sharp authored
We would like to allow host controller drivers to stop using hcd->state. Unfortunately, some host controller drivers use hcd->state as an implicit way of telling the core that a controller has died. The roothub registration functions must assume the host died if hcd->state equals HC_STATE_HALT. To facilitate drivers that don't want to set hcd->state to HC_STATE_RUNNING in their initialization routines, we set the state to running before calling the host controller's start function. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
-
Sarah Sharp authored
The xHCI driver doesn't ever test hcd->state for HC_STATE_HALT. The USB core recently stopped using it internally, so there's no point in setting it in the driver. We still need to set HC_STATE_RUNNING in order to make it past the USB core's hcd->state check in register_roothub(). Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
-
Andiry Xu authored
xHCI 1.0 spec specifies the xHC shall halt within 16ms after software clears Run/Stop bit. In xHCI 0.96 spec the time limit is 16 microframes (2ms), it's too short and often cause dmesg shows "Host controller not halted, aborting reset." message when rmmod xhci-hcd. Modify the time limit to comply with xHCI 1.0 specification and prevents the warning message showing when remove xhci-hcd. Signed-off-by: Andiry Xu <andiry.xu@amd.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
-
Andiry Xu authored
Set hcd->state = HC_STATE_SUSPENDED if there is a power loss during system resume or the system is hibernated, otherwise leave it be. The variable old_state is redundant and made an unreachable code path, so remove it. Signed-off-by: Andiry Xu <andiry.xu@amd.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
-
Sarah Sharp authored
The xhci_bus_suspend() and xhci_bus_resume() functions are a bit hard to read, because they have an ambiguously named variable "port". Rename it to "port_index". Introduce a new temporary variable, "max_ports" that holds the maximum number of roothub ports the host controller supports. This will reduce the number of register reads, and make it easy to change the maximum number of ports when there are two roothubs. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
-
Sarah Sharp authored
The USB core only allows up to 31 (USB_MAXCHILDREN) ports under a roothub. The xHCI driver keeps track of which ports are suspended, which ports have a suspend change bit set, and what time the port will be done resuming. It keeps track of the first two by setting a bit in a u32 variable, suspended_ports or port_c_suspend. The xHCI driver currently assumes we can have up to 256 ports under a roothub, so it allocates an array of 8 u32 variables for both suspended_ports and port_c_suspend. It also allocates a 256-element array to keep track of when the ports will be done resuming. Since we can only have 31 roothub ports, we only need to use one u32 for each of the suspend state and change variables. We simplify the bit math that's trying to index into those arrays and set the correct bit, if we assume wIndex never exceeds 30. (wIndex is zero-based after it's decremented from the value passed in from the USB core.) Finally, we change the resume_done array to only hold 31 elements. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: Andiry Xu <andiry.xu@amd.com>
-
Sarah Sharp authored
The irq enabling code is going to be refactored into a new function, so clean up some checkpatch errors before moving it. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
-
Sarah Sharp authored
Using a #define to redefine a common variable name is a bad thing, especially when the #define is in a header. include/linux/usb/hcd.h redefined bitmap to DeviceRemovable to avoid typing a long field in the hub descriptor. This has unintended side effects for files like drivers/usb/core/devio.c that include that file, since another header included after hcd.h has different variables named bitmap. Remove the bitmap #define and replace instances of it in the host controller code. Cleanup the spaces around function calls and square brackets while we're at it. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Cc: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.yj@renesas.com> Cc: Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com> Cc: Tony Olech <tony.olech@elandigitalsystems.com> Cc: "Robert P. J. Day" <rpjday@crashcourse.ca> Cc: Max Vozeler <mvz@vozeler.com> Cc: Tejun Heo <tj@kernel.org> Cc: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Cc: Rodolfo Giometti <giometti@linux.it> Cc: Mike Frysinger <vapier@gentoo.org> Cc: Anton Vorontsov <avorontsov@mvista.com> Cc: Sebastian Siewior <bigeasy@linutronix.de> Cc: Lothar Wassmann <LW@KARO-electronics.de> Cc: Olav Kongas <ok@artecdesign.ee> Cc: Martin Fuzzey <mfuzzey@gmail.com> Cc: Alan Stern <stern@rowland.harvard.edu> Cc: David Brownell <dbrownell@users.sourceforge.net>
-
Sarah Sharp authored
The test of placing a number of command no-ops on the command ring and counting the number of no-op events that were generated was only used during the initial xHCI driver bring up. This test is no longer used, so delete it. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
-
Sarah Sharp authored
The PM core reacts badly when the return code from usb_runtime_suspend() is not 0, -EAGAIN, or -EBUSY. The PM core regards this as a fatal error, and refuses to run anymore PM helper functions. In particular, usbfs_open() and other usbfs functions will fail because the PM core will return an error code when usb_autoresume_device() is called. This causes libusb and/or lsusb to either hang or segfault. If a USB device cannot suspend for some reason (e.g. a hub doesn't report it has remote wakeup capabilities), we still want lsusb and other userspace programs to work. So return -EBUSY, which will fill people's log files with failed tries, but will ensure userspace still works. Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com>
-
- 11 Mar, 2011 7 commits
-
-
Robert Morell authored
The Tegra2 USB controller doesn't properly deal with misaligned DMA buffers, causing corruption. This is especially prevalent with USB network adapters, where skbuff alignment is often in the middle of a 4-byte dword. To avoid this, allocate a temporary buffer for the DMA if the provided buffer isn't sufficiently aligned. Signed-off-by: Robert Morell <rmorell@nvidia.com> Signed-off-by: Benoit Goby <benoit@android.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Benoit Goby authored
The Tegra 2 SoC has 3 EHCI compatible USB controllers. This patch adds the necessary glue to allow the ehci-hcd driver to work on Tegra 2 SoCs. The platform data is used to configure board-specific phy settings and to configure the operating mode, as one of the ports may be used as a otg port. For additional power saving, the driver supports powering down the phy on bus suspend when it is used, for example, to connect an internal device that use an out-of-band remote wakeup mechanism (e.g. a gpio). Signed-off-by: Benoit Goby <benoit@android.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Benoit Goby authored
Interface used by Tegra's gadget driver and ehci driver to power on and configure the USB PHYs. Signed-off-by: Benoit Goby <benoit@android.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Benoit Goby authored
Add generic access ops for controllers with a ulpi viewport register (e.g. Chipidea/ARC based controllers). Signed-off-by: Benoit Goby <benoit@android.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
wangyanqing authored
I picked up a new DAK-780EX(professional digitl reverb/mix system), which use CH341T chipset to communication with computer on 3/2011 and the CH341T's vendor code is 1a86 Looking up the CH341T's vendor and product id's I see: 1a86 QinHeng Electronics 5523 CH341 in serial mode, usb to serial port converter CH341T,CH341 are the products of the same company, maybe have some common hardware, and I test the ch341.c works well with CH341T Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Paul Bolle authored
On a laptop I see these errors on (most) resumes: hub 3-0:1.0: over-current change on port 1 hub 3-0:1.0: over-current change on port 2 Since over-current conditions can disappear quite quickly it's better to downgrade that message to debug level, recheck for an over-current condition a little later and only print and over-current condition error if that condition (still) exists when it's rechecked. Add similar logic to hub over-current changes. (That code is untested, as those changes do not occur on this laptop.) Signed-off-by: Paul Bolle <pebolle@tiscali.nl> Acked-by: Alan Stern <stern@rowland.harvard.edu> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Hubert Feurstein authored
Fix the following section mismatch warning: WARNING: drivers/usb/built-in.o(.data+0x74c): Section mismatch in reference from the variable ehci_atmel_driver to the function .init.text:ehci_atmel_drv_probe() The variable ehci_atmel_driver references the function __init ehci_atmel_drv_probe() If the reference is valid then annotate the variable with __init* or __refdata (see linux/init.h) or name the variable: *_template, *_timer, *_sht, *_ops, *_probe, *_probe_one, *_console, Signed-off-by: Hubert Feurstein <h.feurstein@gmail.com> Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
- 09 Mar, 2011 3 commits
-
-
JF Argentino authored
Adding support for the OLIMEX ARM-USB-OCD-H JTAG device (id 15ba:002b) based on FTDI FT2232H Signed-off-by: JF Argentino <jf.argentino@free.fr> Acked-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Herton Ronaldo Krzesinski authored
On https://bugs.launchpad.net/ubuntu/+source/linux/+bug/636091, one of the cases reported is a big timeout on option_send_setup, which causes some side effects as tty_lock is held. Looks like some of ZTE MF626 devices also don't like the RTS/DTR setting in option_send_setup, like with 4G XS Stick W14. The reporter confirms which this it solves the long freezes in his system. Signed-off-by: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com> Cc: stable <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Hao Wu authored
Direct access to PMIC register is not safe and will impact battery charging. New IPC command supported in SCU FW for VBus power control. USB OTG driver will switch to such commands instead of direct access to PMIC register for safety and SCU FW will handle the actual work after got the request(IPC command). Due to this change, usb driver should wait more time for sync OTGSC with USBCFG by SCU. Update wait time from 2ms to 5ms. Signed-off-by: Hao Wu <hao.wu@intel.com> Signed-off-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
- 07 Mar, 2011 7 commits
-
-
Lars-Peter Clausen authored
Currently all boards using the s3c2410_udc driver use a GPIO to control the state of the pullup, as a result the same code is reimplemented in each board This patch changes these boards to use the common implementation for GPIO controlled pullup in the UDC driver. Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Acked-by: Vasily Khoruzhick <anarsoul@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Lars-Peter Clausen authored
Currently all boards using the s3c2410_udc driver use a GPIO to control the state of the pullup, as a result the same code is reimplemented in each board file. This patch adds support for using a GPIO to control the pullup state to the udc driver, so the boards can use a common implementation. Signed-off-by: Lars-Peter Clausen <lars@metafoo.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Anand Gadiyar authored
Most revisions of the OMAP4 Blaze/SDP platform do not have the EHCI signals routed by default. The pads are routed for the alternate HSI functionality instead, and explicit board modifications are needed to route the signals to the USB PHY on the board. Also, turning on the PHY connected to the EHCI port causes a board reboot during bootup due to an unintended short on the rails - this affects many initial revisions of the board, and needs a minor board mod to fix (or as a workaround, one should not attempt to power on the USB PHY). Given that these boards need explicit board mods to even get EHCI working (separate from the accidental short above), we should not attempt to enable EHCI by default. So drop the EHCI support from the board files for the Blaze/SDP platforms. Signed-off-by: Anand Gadiyar <gadiyar@ti.com> Cc: Keshava Munegowda <keshava_mgowda@ti.com> Cc: Tony Lindgren <tony@atomide.com> Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Sergei Shtylyov authored
Commit ab1666c1 (USB: quirk PLL power down mode) added code that reads the revision ID from the PCI configuration register while it's stored by PCI subsystem in the 'revision' field of 'struct pci_dev'... Signed-off-by: Sergei Shtylyov <sshtylyov@ru.mvista.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Pavankumar Kondeti authored
This driver is used across all MSM SoCs. Hence give a generic name. All Functions and strutures are also using "msm_otg" as prefix. Signed-off-by: Pavankumar Kondeti <pkondeti@codeaurora.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Arvid Brodin authored
This fixes a problem with my previous patch series where there's a great risk that the kernel will crash when unplugging interrupt devices from the USB port. These lines must have got missing when I rebased the patches from the older kernel I was working with to 2.6.37 and 2.6-next: This fixes a bug where the kernel may crash if you unplug a USB device that has active interrupt transfers. Signed-off-by: Arvid Brodin <arvid.brodin@enea.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Alan Stern authored
The hcd->state variable is a disaster. It's not clearly owned by either usbcore or the host controller drivers, and they both change it from time to time, potentially stepping on each other's toes. It's not protected by any locks. And there's no mechanism to prevent it from going through an invalid transition. This patch (as1451) takes a first step toward fixing these problems. As it turns out, usbcore uses hcd->state for essentially only two things: checking whether the controller's root hub is running and checking whether the controller has died. Therefore the patch adds two new atomic bitflags to the hcd structure, to store these pieces of information. The new flags are used only by usbcore, and a private spinlock prevents invalid combinations (a dead controller's root hub cannot be running). The patch does not change the places where usbcore sets hcd->state, since HCDs may depend on them. Furthermore, there is one place in usb_hcd_irq() where usbcore still must use hcd->state: An HCD's interrupt handler can implicitly indicate that the controller died by setting hcd->state to HC_STATE_HALT. Nevertheless, the new code is a big improvement over the current code. The patch makes one other change. The hcd_bus_suspend() and hcd_bus_resume() routines now check first whether the host controller has died; if it has then they return immediately without calling the HCD's bus_suspend or bus_resume methods. This fixes the major problem reported in Bugzilla #29902: The system fails to suspend after a host controller dies during system resume. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Alex Terekhov <a.terekhov@gmail.com> CC: <stable@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
- 03 Mar, 2011 2 commits
-
-
Huzaifa Sidhpurwala authored
timeout variable is not used anywhere in int write_cmd_usb, remove it Signed-off-by: Huzaifa Sidhpurwala <huzaifas@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Huzaifa Sidhpurwala authored
is_iso variable is not used anywhere, remove it Signed-off-by: Huzaifa Sidhpurwala <huzaifas@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-