Since commit 607ca46e ('UAPI: (Scripted) Disintegrate include/linux') the
list of functionality constants moved to include/uapi/linux/i2c.h. Update the
reference accordingly.

Fixes: 607ca46e ('UAPI: (Scripted) Disintegrate include/linux')
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Add initial support to the Broadcom iProc I2C controller found in the
iProc family of SoCs.

The iProc I2C controller has separate internal TX and RX FIFOs, each has
a size of 64 bytes. The iProc I2C controller supports two bus speeds
including standard mode (100kHz) and fast mode (400kHz)
Signed-off-by: Ray Jui <rjui@broadcom.com>
Reviewed-by: Scott Branden <sbranden@broadcom.com>
Reviewed-by: Kevin Cernekee <cernekee@chromium.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

While here, fix few indentations issues across the code. There is no functional
change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Allow bus clock specification as a common clock handle. This makes this
controller easier to use in a setup based on common clock framework.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Commit 9439eb3a ("asm-generic: io: implement relaxed
accessor macros as conditional wrappers") has added
{read,write}{b,w,l,q}_relaxed to include/asm-generic/io.h.
So COMPILE_TEST can be added.
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

There was quite some confusion why this completion is there and if it is
still necessary. Sadly, it is. However, let's improve the comments and
share what we rediscovered.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

clock-frequency property is meant to control the bus frequency for i2c bus
drivers, but it was incorrectly used to specify i2c controller input clock
frequency.
Introduce new attribute, opencores,ip-clock-frequency, that specifies i2c
controller clock frequency and make clock-frequency attribute compatible
with other i2c drivers. Maintain backwards compatibility in case
opencores,ip-clock-frequency attribute is missing.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Support CPU BE mode by adding endianness conversion for memcpy interactions.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Acked-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

IOSF_MBI depends on PCI, so we should not select it but depend on it.
This ensures also we compile on X86 only, other archs will break because
of an arch specific include. Also depend on ACPI since this driver uses
it.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: David E. Box <david.e.box@linux.intel.com>

Do SCL timing parameter calculation conditionally depending are custom
parameters provided since calculated values will get instantly overwritten
by provided parameters.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Trying to register an I2C device asynchronously (via async_schedule() call)
results in an ugly warning from request_module() warning about potential
deadlock (because request_module tries to wait for async works to
complete). While we could try to switch to request_module_nowait(), other
buses, as well as I2C itself when not using device tree, do not try to load
modules, but rather rely on the standard infrastructure (udev) to execute
module loading, and we should be doing the same.
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This patch implements an I2C bus sharing mechanism between the host and platform
hardware on select Intel BayTrail SoC platforms using the X-Powers AXP288 PMIC.

On these platforms access to the PMIC must be shared with platform hardware. The
hardware unit assumes full control of the I2C bus and the host must request
access through a special semaphore. Hardware control of the bus also makes it
necessary to disable runtime pm to avoid interfering with hardware transactions.
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Adds support for acquiring and releasing a hardware bus lock in the i2c
designware core transfer function. This is needed for i2c bus controllers
that are shared with but not controlled by the kernel.
Signed-off-by: David E. Box <david.e.box@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Add i2c-mux-idle-disconnect device tree property to PCA954x mux driver. The new
property forces the multiplexer to disconnect child buses in idle state. This is
used, for example, when there are several multiplexers on the same bus and the
devices on the underlying buses might have same I2C addresses.
Signed-off-by: Alexander Sverdlin <alexander.sverdlin@nsn.com>
[wsa: added a newline]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

readl/writel is too expensive especially on Cortex A9 w/ outer L2 cache.
This introduces i2c read/write delays on Marvell BG2/BG2Q SoCs when there
are heavy L2 cache maintenance operations at the same time.

The driver does not perform DMA, so it's safe to use the relaxed version.
From another side, the relaxed io accessor macros are available on all
architectures now, so we can use the relaxed versions instead.
Signed-off-by: Jisheng Zhang <jszhang@marvell.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The clk_khz field makes sense only if SS counters are not provided. Since we
provide them for Haswell and Baytrail explicitly we may omit the clk_khz
parameter.
Reviewed-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The Moorestown support bits were removed few years ago. This is a follow up to
that changes.
Suggested-by: David Cohen <david.a.cohen@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This patch fixes up some whitespace issues and addresses a few
checkpatch warnings.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Declaring attribute groups can be done with macros these days, let's use
them for consistency and readability reasons. Also, put the ATTR macros
directly below the referenced functions while we are here.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The ret variable is set and never used in the error path of i2c_imx_dma_request.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Fugang Duan <B38611@freescale.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

ACPI specification allows I2C devices with multiple addresses. The current
implementation goes over all addresses and assigns the last one to the
device. This is typically not the primary address of the device.

Instead of doing that we assign the first address to the device and then
let the driver handle rest of the addresses as it wishes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Cadence I2C controller has the following bugs:
- completion indication is not given to the driver at the end of
a read/receive transfer with HOLD bit set.
- Invalid read transaction are generated on the bus when HW timeout
condition occurs with HOLD bit set.

As a result of the above, if a set of messages to be transferred with
repeated start includes any message following a read message,
completion is never indicated and timeout occurs.
Hence a check is implemented to return -EOPNOTSUPP for such sequences.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: Vishnu Motghare <vishnum@xilinx.com>
[wsa: fixed some whitespaces]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

This patch fixes I2C trivial-devices.txt DT documentation file to
reference isil (NASDAQ symbol and the most used prefix inside the
kernel) for Intersil.

It reverts 7c75c1d5 ("dt-bindings: Document deprecated device
vendor name to fix related warning").
Signed-off-by: Arnaud Ebalard <arno@natisbad.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

wait_for_completion_timeout does not return negative values so
"result" handling here should be simplified to cover the actually
possible cases only.
Signed-off-by: Nicholas Mc Guire <der.herr@hofr.at>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

On Rockchip I2C the controller drops SDA low slightly too soon to meet
the "repeated start" requirements.

>From my own experimentation over a number of rates:
 - controller appears to drop SDA at .875x (7/8) programmed clk high.
 - controller appears to keep SCL high for 2x programmed clk high.

The first rule isn't enough to meet tSU;STA requirements in
Standard-mode on the system I tested on.  The second rule is probably
enough to meet tHD;STA requirements in nearly all cases (especially
after accounting for the first), but it doesn't hurt to account for it
anyway just in case.

Even though the repeated start requirement only need to be accounted
for during a small part of the transfer, we'll adjust the timings for
the whole transfer to meet it.  I believe that adjusting the timings
in just the right place to switch things up for repeated start would
require several extra interrupts and that doesn't seem terribly worth
it.

With this change and worst case rise/fall times, I see 100kHz i2c
going to ~85kHz.  With slightly optimized rise/fall (800ns / 50ns) I
see i2c going to ~89kHz.  Fast-mode isn't affected much because
tSU;STA is shorter relative to tHD;STA there.

As part of this change we needed to account for the SDA falling time.
The specification indicates that this should be the same, but we'll
follow Designware's lead and add a binding.  Note that we deviate from
Designware and assign the default SDA falling time to be the same as
the SCL falling time, which is incredibly likely.
Signed-off-by: Doug Anderson <dianders@chromium.org>
[wsa: rebased to i2c/for-next]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The number of clock cycles to be written into the CLKDIV register
that determines the I2C clk high phase includes the rise time.
So to meet the timing requirements defined in the I2C specification
which defines the minimal time SCL has to be high, the rise time
has to taken into account. The same applies to the low phase with
falling time.

In my test on RK3288-Pink2 board, which is not an upstream board yet,
if external pull-up resistor is 4.7K, rise_ns is about 700ns.
So the measured high_ns is about 3900ns, which is less than 4000ns
(the minimum high_ns in I2C specification for Standard-mode).

To fix this bug min_low_ns should include fall time and min_high_ns
should include rise time.

This patch merged the patch from chromium project which can get the
rise and fall times for signals from the device tree. This allows us
to more accurately calculate timings. see:
https://chromium-review.googlesource.com/#/c/232774/Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
[wsa: fixed a typo in the docs]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

The I2C controller sends a NACK to the slave when transfer size register
reaches zero, irrespective of the hold bit. So, in order to handle transfers
greater than 252 bytes, the transfer size register has to be maintained at a
value >= 1. This patch implements the same.
The interrupt status is cleared at the beginning of the isr instead of
the end, to avoid missing any interrupts.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
[wsa: added braces around else branch]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

CPPCHECK rightfully says:

drivers/i2c/busses/i2c-pmcmsp.c:151: style: The function 'pmcmsptwi_reg_to_clock' is never used.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

There haven't been any I2C driver that use the legacy suspend/resume
callbacks for a while now and new drivers are supposed to use PM ops. So
remove support for legacy suspend/resume for I2C drivers.

Since there aren't any special bus specific things to do during
suspend/resume and since the PM core will automatically fallback directly to
using the device's PM ops if no bus PM ops are specified there is no need to
have any I2C bus PM ops.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Pull ACCESS_ONCE cleanup preparation from Christian Borntraeger:
 "kernel: Provide READ_ONCE and ASSIGN_ONCE

  As discussed on LKML http://marc.info/?i=54611D86.4040306%40de.ibm.com
  ACCESS_ONCE might fail with specific compilers for non-scalar
  accesses.

  Here is a set of patches to tackle that problem.

  The first patch introduce READ_ONCE and ASSIGN_ONCE.  If the data
  structure is larger than the machine word size memcpy is used and a
  warning is emitted.  The next patches fix up several in-tree users of
  ACCESS_ONCE on non-scalar types.

  This does not yet contain a patch that forces ACCESS_ONCE to work only
  on scalar types.  This is targetted for the next merge window as Linux
  next already contains new offenders regarding ACCESS_ONCE vs.
  non-scalar types"

* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/borntraeger/linux:
  s390/kvm: REPLACE barrier fixup with READ_ONCE
  arm/spinlock: Replace ACCESS_ONCE with READ_ONCE
  arm64/spinlock: Replace ACCESS_ONCE READ_ONCE
  mips/gup: Replace ACCESS_ONCE with READ_ONCE
  x86/gup: Replace ACCESS_ONCE with READ_ONCE
  x86/spinlock: Replace ACCESS_ONCE with READ_ONCE
  mm: replace ACCESS_ONCE with READ_ONCE or barriers
  kernel: Provide READ_ONCE and ASSIGN_ONCE

Pull clk framework updates from Mike Turquette:
 "This is much later than usual due to several last minute bugs that had
  to be addressed.  As usual the majority of changes are new drivers and
  modifications to existing drivers.  The core recieved many fixes along
  with the groundwork for several large changes coming in the future
  which will better parition clock providers from clock consumers"

* tag 'clk-for-linus-3.19' of git://git.linaro.org/people/mike.turquette/linux: (86 commits)
  clk: samsung: Fix Exynos 5420 pinctrl setup and clock disable failure due to domain being gated
  ARM: OMAP3: clock: fix boot breakage in legacy mode
  ARM: OMAP2+: clock: fix DPLL code to use new determine rate APIs
  clk: Really fix deadlock with mmap_sem
  clk: mmp: fix sparse non static symbol warning
  clk: Change clk_ops->determine_rate to return a clk_hw as the best parent
  clk: change clk_debugfs_add_file to take a struct clk_hw
  clk: Don't expose __clk_get_accuracy
  clk: Don't try to use a struct clk* after it could have been freed
  clk: Remove unused function __clk_get_prepare_count
  clk: samsung: Fix double add of syscore ops after driver rebind
  clk: samsung: exynos4: set parent of sclk_hdmiphy to hdmi
  clk: samsung: exynos4415: Fix build with PM_SLEEP disabled
  clk: samsung: remove unnecessary inclusion of header files from clk.h
  clk: samsung: remove unnecessary CONFIG_OF from clk.c
  clk: samsung: Spelling s/bwtween/between/
  clk: rockchip: Add support for the mmc clock phases using the framework
  clk: rockchip: add bindings for the mmc clocks
  clk: rockchip: rk3288 export i2s0_clkout for use in DT
  clk: rockchip: use clock ID for DMC (memory controller) on rk3288
  ...

Pull more i2c updates from Wolfram Sang:
 "Included are two bugfixes needing some bigger refactoring (sh_mobile:
  deferred probe with DMA, mv64xxx: fix offload support) and one
  deprecated driver removal I thought would go in via ppc but I
  misunderstood.  It has a proper ack from BenH"

* 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
  i2c: sh_mobile: fix uninitialized var when debug is enabled
  macintosh: therm_pm72: delete deprecated driver
  i2c: sh_mobile: I2C_SH_MOBILE should depend on HAS_DMA
  i2c: sh_mobile: rework deferred probing
  i2c: sh_mobile: refactor DMA setup
  i2c: mv64xxx: rework offload support to fix several problems
  i2c: mv64xxx: use BIT() macro for register value definitions

Pull SCSI update from James Bottomley:
 "This is a much shorter set of patches that were on the go but didn't
  make it in to the early pull request for the merge window.  It's
  really a set of bug fixes plus some final cleanup work on the new tag
  queue API"

* tag 'scsi-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
  storvsc: ring buffer failures may result in I/O freeze
  ipr: set scsi_level correctly for disk arrays
  ipr: add support for async scanning to speed up boot
  scsi_debug: fix missing "break;" in SDEBUG_UA_CAPACITY_CHANGED case
  scsi_debug: take sdebug_host_list_lock when changing capacity
  scsi_debug: improve driver description in Kconfig
  scsi_debug: fix compare and write errors
  qla2xxx: fix race in handling rport deletion during recovery causes panic
  scsi: blacklist RSOC for Microsoft iSCSI target devices
  scsi: fix random memory corruption with scsi-mq + T10 PI
  Revert "[SCSI] mpt3sas: Remove phys on topology change"
  Revert "[SCSI] mpt2sas: Remove phys on topology change."
  esas2r: Correct typos of "validate" in a comment
  fc: FCP_PTA_SIMPLE is 0
  ibmvfc: remove unused tag variable
  scsi: remove MSG_*_TAG defines
  scsi: remove scsi_set_tag_type
  scsi: remove scsi_get_tag_type
  scsi: never drop to untagged mode during queue ramp down
  scsi: remove ->change_queue_type method

Pull CONFIG_PM_RUNTIME elimination from Rafael Wysocki:
 "This removes the last few uses of CONFIG_PM_RUNTIME introduced
  recently and makes that config option finally go away.

  CONFIG_PM will be available directly from the menu now and also it
  will be selected automatically if CONFIG_SUSPEND or CONFIG_HIBERNATION
  is set"

* tag 'pm-config-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
  PM: Eliminate CONFIG_PM_RUNTIME
  tty: 8250_omap: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  sound: sst-haswell-pcm: Replace CONFIG_PM_RUNTIME with CONFIG_PM
  spi: Replace CONFIG_PM_RUNTIME with CONFIG_PM

Pull misc kbuild changes from Michal Marek:
 "There are only a few things in the misc branch:

   - Fix for bugon.cocci semantic patch
   - Kdevelop4 files are .gitignored
   - Put make binrpm-pkg on diet"

* 'misc' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
  scripts/package: binrpm-pkg do not create source and devel package
  .gitignore: Add Kdevelop4 project files
  bugon.cocci: fix Options at the macro

Pull kbuild updates from Michal Marek:
 "Here are the kbuild changes for v3.19-rc1:

   - Cleanups and deduplication in the main Makefile and
     scripts/Makefile.*
   - Sort the output of *config targets in make help
   - Old <linux/version.h> is always removed to avoid a surprise during
     bisecting
   - Warning fix in kconfig"

* 'kbuild' of git://git.kernel.org/pub/scm/linux/kernel/git/mmarek/kbuild:
  kbuild: remove redundant -rR flag of hdr-inst
  kbuild: Fix make help-<board series> on powerpc
  kbuild: Automatically remove stale <linux/version.h> file
  kconfig: Fix warning "‘jump’ may be used uninitialized"
  Makefile: sort list of defconfig targets in make help output
  kbuild: Remove duplicate $(cmd) definition in Makefile.clean
  kbuild: collect shorthands into scripts/Kbuild.include

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

Pull vfs pile #3 from Al Viro:
 "Assorted fixes and patches from the last cycle"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs:
  [regression] chunk lost from bd9b51
  vfs: make mounts and mountstats honor root dir like mountinfo does
  vfs: cleanup show_mountinfo
  init: fix read-write root mount
  unfuck binfmt_misc.c (broken by commit e6084d4a)
  vm_area_operations: kill ->migrate()
  new helper: iter_is_iovec()
  move_extent_per_page(): get rid of unused w_flags
  lustre: get rid of playing with ->fs
  btrfs: filp_open() returns ERR_PTR() on failure, not NULL...

Merge tag 'ecryptfs-3.19-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs

Pull eCryptfs fixes from Tyler Hicks:
 "Fixes for filename decryption and encrypted view plus a cleanup

   - The filename decryption routines were, at times, writing a zero
     byte one character past the end of the filename buffer

   - The encrypted view feature attempted, and failed, to roll its own
     form of enforcing a read-only mount instead of letting the VFS
     enforce it"

* tag 'ecryptfs-3.19-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
  eCryptfs: Remove buggy and unnecessary write in file name decode routine
  eCryptfs: Remove unnecessary casts when parsing packet lengths
  eCryptfs: Force RO mount when encrypted view is enabled