- 12 Feb, 2019 40 commits
-
-
Julian Wiedmann authored
qeth_l3_query_arp_cache_info() indicates a data length that's much larger than the actual length of its request (ie. the value passed to qeth_get_setassparms_cmd()). The confusion presumably comes from the fact that the cmd _response_ can be quite large - but that's no concern for the initial request IO. Fixing this up allows us to use the generic qeth_send_ipa_cmd() infrastructure. Signed-off-by:
Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
David S. Miller authored
Yangbo Lu says: ==================== Add ENETC PTP clock driver There is same QorIQ 1588 timer IP block on the new ENETC Ethernet controller with eTSEC/DPAA Ethernet controllers. However it's different endianness (little-endian) and using PCI driver. To support ENETC PTP driver, ptp_qoriq driver needed to be reworked to make functions global for reusing, to add little- endian support, to add ENETC memory map support, and to add ENETC dependency for ptp_qoriq driver. In addition, although ENETC PTP driver is a PCI driver, the dts node still could be used. Currently the ls1028a dtsi which is the only platform by now using ENETC is not complete, so there is still dependency for ENETC PTP node upstreaming. This will be done in the near future. The hardware timestamping support for ENETC is done but needs to be reworked with new method in internal git tree, and will be sent out soon. ==================== Signed-off-by: -
Saeed Mahameed authored
When an ethernet frame is padded to meet the minimum ethernet frame size, the padding octets are not covered by the hardware checksum. Fortunately the padding octets are usually zero's, which don't affect checksum. However, it is not guaranteed. For example, switches might choose to make other use of these octets. This repeatedly causes kernel hardware checksum fault. Prior to the cited commit below, skb checksum was forced to be CHECKSUM_NONE when padding is detected. After it, we need to keep skb->csum updated. However, fixing up CHECKSUM_COMPLETE requires to verify and parse IP headers, it does not worth the effort as the packets are so small that CHECKSUM_COMPLETE has no significant advantage. Future work: when reporting checksum complete is not an option for IP non-TCP/UDP packets, we can actually fallback to report checksum unnecessary, by looking at cqe IPOK bit. Fixes: 88078d98 ("net: pskb_trim_rcsum() and CHECKSUM_COMPLETE are friends") Cc: Eric Dumazet <edumazet@google.com> Signed-off-by:
Saeed Mahameed <saeedm@mellanox.com> Signed-off-by:
Tariq Toukan <tariqt@mellanox.com> Reviewed-by:
Eric Dumazet <edumazet@google.com> Signed-off-by:
-
Yangbo Lu authored
This patch to add enetc_ptp driver into QorIQ PTP list for maintaining. Signed-off-by:
Yangbo Lu <yangbo.lu@nxp.com> Signed-off-by:
-
Yangbo Lu authored
This patch is to add PTP clock driver for ENETC. The driver reused QorIQ PTP clock driver. Signed-off-by:
-
Yangbo Lu authored
This patch is to add QorIQ PTP support for ENETC. ENETC PTP driver which is a PCI driver for same 1588 timer IP block will reuse QorIQ PTP driver. Signed-off-by:
-
Yangbo Lu authored
The 1588 timer on eTSEC Ethernet controller uses different register memory map with DPAA Ethernet controller. Now the new ENETC Ethernet controller uses same reigster memory map with DPAA. To support ENETC, let's use register memory map of DPAA/ENETC in default. Signed-off-by:
-
Yangbo Lu authored
Specify "little-endian" property if the 1588 timer IP block is little-endian mode. The default endian mode is big-endian. Signed-off-by:
-
Yangbo Lu authored
There is QorIQ 1588 timer IP block on the new ENETC Ethernet controller. However it uses little endian mode which is different with before. This patch is to add little endian support for the driver by using "little-endian" dts node property. Signed-off-by:
-
Yangbo Lu authored
Moved QorIQ PTP clock initialization/free into new functions ptp_qoriq_init()/ptp_qoriq_free(). These functions could also be reused by ENETC PTP drvier which is a PCI driver for same 1588 timer IP block. Signed-off-by:
-
Yangbo Lu authored
This patch is to make functions of ptp operations global, so that ENETC PTP driver which is a PCI driver for same 1588 timer IP block could reuse them. Signed-off-by:
-
Yangbo Lu authored
Strings containing "ptp_qoriq" or "qoriq_ptp" which were used for structure/function names were complained by users. Let's just use the unique "ptp_qoriq" to make these names more consistent. This patch is just to unify the names using "ptp_qoriq". It hasn't changed any functions. Signed-off-by:
-
Brian Norris authored
There are several skb_* functions where the locked and unlocked functions are confusingly documented. For several of them, the kernel-doc for the unlocked version is placed above the locked version, which to the casual reader makes it seems like the locked version "takes no locks and you must therefore hold required locks before calling it." One can see, for example, that this link claims to document skb_queue_head(), while instead describing __skb_queue_head(). https://www.kernel.org/doc/html/latest/networking/kapi.html#c.skb_queue_head The correct documentation for skb_queue_head() is also included further down the page. This diff tested via: $ scripts/kernel-doc -rst include/linux/skbuff.h net/core/skbuff.c No new warnings were seen, and the output makes a little more sense. Signed-off-by:
Brian Norris <briannorris@chromium.org> Signed-off-by:
-
David S. Miller authored
Florian Fainelli says: ==================== Remove getting SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS AFAICT there is no code that attempts to get the value of the attribute SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS while it is used with switchdev_port_attr_set(). This is effectively no doing anything and it can slow down future work that tries to make modifications in these areas so remove that. ==================== Signed-off-by: -
Florian Fainelli authored
There is no code that tries to get the attribute SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS, remove support for doing that. Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Acked-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Acked-by:
Jiri Pirko <jiri@mellanox.com> Signed-off-by:
-
Florian Fainelli authored
There is no code that attempts to get the SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS attribute, remove support for that. Signed-off-by:
-
Florian Fainelli authored
There is no code that will query the SWITCHDEV_ATTR_ID_PORT_BRIDGE_FLAGS attribute remove support for that. Signed-off-by:
Ido Schimmel <idosch@mellanox.com> Signed-off-by:
-
Heiner Kallweit authored
Use new function phy_modify_mmd_changed(), the result speaks for itself. Signed-off-by:
Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
-
Vakul Garg authored
Addition of tls1.3 support broke tls1.2 handshake when async crypto accelerator is used. This is because the record type for non-data records is not propagated to user application. Also when async decryption happens, the decryption does not stop when two different types of records get dequeued and submitted for decryption. To address it, we decrypt tls1.2 non-data records in synchronous way. We check whether the record we just processed has same type as the previous one before checking for async condition and jumping to dequeue next record. Fixes: 130b392c ("net: tls: Add tls 1.3 support") Signed-off-by:
Vakul Garg <vakul.garg@nxp.com> Signed-off-by:
-
Li RongQing authored
This can remove redundant check Signed-off-by:
Li RongQing <lirongqing@baidu.com> Signed-off-by:
-
Russell King authored
There are several places which make the decision whether to access the XLGMAC vs GMAC that only check for PHY_INTERFACE_MODE_10GKR and not its XAUI variant. Switch these to use the new helper so that we have consistency through the driver. Signed-off-by:
Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by:
Maxime Chevallier <maxime.chevallier@bootlin.com> Signed-off-by:
-
Russell King authored
Add a mvpp2_is_xlg() helper to identify whether the interface mode should be using the XLGMAC rather than the GMAC. Signed-off-by:
-
Russell King authored
Provide phylink_init_eee() to allow MAC drivers to initialise PHY EEE from within the ethtool set_eee() method. Signed-off-by:
-
Russell King authored
There's little point calling mac_config() when the link is down. Signed-off-by:
-
Vasundhara Volam authored
This reverts commit b639583f. As per discussion with Jakub Kicinski and Michal Kubecek, this will be better addressed by soon-too-come ethtool netlink API with additional indication that given configuration request is supposed to be persisted. Also, remove the parameter support from bnxt_en driver. Cc: Jiri Pirko <jiri@mellanox.com> Cc: Michael Chan <michael.chan@broadcom.com> Cc: Michal Kubecek <mkubecek@suse.cz> Suggested-by:
Jakub Kicinski <jakub.kicinski@netronome.com> Signed-off-by:
Vasundhara Volam <vasundhara-v.volam@broadcom.com> Signed-off-by:
-
David S. Miller authored
Christoph Hellwig says: ==================== net: don't pass a NULL struct device to DMA API functions v2 We still have a few drivers which pass a NULL struct device pointer to DMA API functions, which generally is a bad idea as the API implementations rely on the device not only for ops selection, but also the dma mask and various other attributes. This series contains all easy conversions to pass a struct device, besides that there also is some arch code that needs separate handling, a driver that should not use the DMA API at all, and one that is a complete basket case to be deal with separately. Changes since v1: - fix an inverted ifdef in CAIF - update the smc911x changelog - split the series, this only contains the networking patches ==================== Signed-off-by: -
Christoph Hellwig authored
The DMA API generally relies on a struct device to work properly, and only barely works without one for legacy reasons. Pass the easily available struct device from the platform_device to remedy this. Note that smc911x apparently is a PIO chip with an external DMA handshake, and we probably use the wrong device here. But at least it matches the mapping side, which apparently works or at least worked in the not too distant past. Signed-off-by:
Christoph Hellwig <hch@lst.de> Signed-off-by:
-
Christoph Hellwig authored
The DMA API generally relies on a struct device to work properly, and only barely works without one for legacy reasons. Pass the easily available struct device from the platform_device to remedy this. Also use GFP_KERNEL instead of GFP_ATOMIC as the gfp_t for the memory allocation, as we aren't in interrupt context or under a lock. Signed-off-by:
-
Christoph Hellwig authored
The DMA API generally relies on a struct device to work properly, and only barely works without one for legacy reasons. Pass the easily available struct device from the platform_device to remedy this. Signed-off-by:
-
Christoph Hellwig authored
The DMA API generally relies on a struct device to work properly, and only barely works without one for legacy reasons. Pass the easily available struct device from the platform_device to remedy this. Note that this driver seems to entirely lack dma_map_single error handling, but that is left for another time. Signed-off-by:
-
Christoph Hellwig authored
The DMA API generally relies on a struct device to work properly, and only barely works without one for legacy reasons. Pass the easily available struct device from the platform_device to remedy this. Note this driver seems to lack dma_unmap_* calls entirely, but fixing that is left for another time. Signed-off-by:
-
Christoph Hellwig authored
The DMA API generally relies on a struct device to work properly, and only barely works without one for legacy reasons. Pass the easily available struct device from the platform_device to remedy this. Signed-off-by:
Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by:
-
Christoph Hellwig authored
The DMA API generally relies on a struct device to work properly, and only barely works without one for legacy reasons. Pass the easily available struct device from the platform_device to remedy this. Signed-off-by:
-
Christoph Hellwig authored
The DMA API generally relies on a struct device to work properly, and only barely works without one for legacy reasons. Pass the easily available struct device from the platform_device to remedy this. Also use the proper Kconfig symbol to check for DMA API availability. Signed-off-by:
-
David S. Miller authored
Ido Schimmel says: ==================== mlxsw: Several updates Patches #1-#3 contain misc updates for the mlxsw driver, one of which is a fix following recent introduction of flow_rule infrastructure. Patch #4 avoids double sourcing of lib.sh in forwarding selftests. ==================== Signed-off-by: -
Jiri Pirko authored
Don't source lib.sh 2 times and make the script work with ifnames passed on the command line. Signed-off-by:
-
Ido Schimmel authored
The driver does not support VLAN push and pop, but only VLAN modify. Fixes: 73867881 ("drivers: net: use flow action infrastructure") Signed-off-by:
-
Ido Schimmel authored
In case the register access failed an error would be logged anyway, so we can drop the warning. Signed-off-by:
-
Nir Dotan authored
The LAG port collecting (receive) function was mistakenly set when the port was registered as a LAG member, while it should be set only when the port collection state is set to true. Set LAG port to collecting when it is set to distributing, as described in the IEEE link aggregation standard coupled control mux machine state diagram. Signed-off-by:
Nir Dotan <nird@mellanox.com> Acked-by:
-
David S. Miller authored
Ursula Braun says: ==================== net/smc: patches 2019-02-12 here are patches for SMC: * patches 1 and 3 optimize SMC-R tx logic * patch 2 is a cleanup without functional change * patch 4 optimizes rx logic * patches 5 and 6 improve robustness in link group and IB event handling * patch 7 establishes Karsten Graul as another SMC maintainer ==================== Signed-off-by:
-
