Majority of host drivers using IDE PCI layer set drive->autotune, the only
exceptions are:

generic.c
ns87415.c
rz1000.c
trm290.c
* no ->set_pio_mode method

it821x.c:
* if memory allocation fails drive->autotune won't be set
  (but there also won't be ->set_pio_mode method in such case)

piix.c:
* MPIIX controller (no ->init_hwif method so also no ->set_pio_mode method)

However if there is no ->set_pio_mode method there are no changes in behavior
w.r.t. PIO tuning so always set drive->autotune in ide_pci_setup_ports().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Since cs5520 uses VDMA best PIO mode was tuned anyway by ide_dma_check()
but only if DMA was successfully initialized.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add IDE_HFLAG_LEGACY_IRQS host flag to tell ide_pci_setup_ports() to set
hwif->irq to legacy IRQ 14/15 (iff hwif->irq is not already set) and convert
atiixp, piix, serverworks, sis5513 and slc90e66 host drivers to use it.

While at it:

* In piix.c add IDE_HFLAGS_PIIX define and don't use ->init_hwif for MPIIX.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add IDE_HFLAG_SERIALIZE host flag to tell ide_pci_setup_ports() to set
hwif/mate->serialized and convert aec62xx, cs5530 and sc1200 host drivers
to use it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add IDE_HFLAG_ERROR_STOPS_FIFO host flag and use it instead
of hwif->err_stops_fifo.  As a side-effect this change fixes
hwif->err_stops_fifo not being restored by ide_hwif_restore().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add DECLARE_ICH_DEV() macro.

While at it:

* Add init_hwif_ich() (->init_hwif method) for ICH controllers.

* Rename init_chipset_piix() to init_chipset_ich() and use it only for
  ICH controllers.

* Remove no longer needed piix_is_ichx() helper.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* No need to disable UDMA in ->init_hwif method for ATP850UF (and since we
  now always tune PIO it will be disabled by ->set_pio_mode calls anyway).

* Bump driver version.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Now that all users were fixed we can safely remove it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Merge init_setup_{svwks,csb6}() into svwks_init_one().

While at it:

* Remove redundant dev->device checks.

* Operate on a local copy of serverworks_chipsets[] entry.

* Use pci_resource_start().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Split off pdc202ata4_fixup_irq() helper from init_setup_pdc202ata4().

* Merge init_setup_{pdc202ata4,pdc20265,pdc202xx}() into pdc202xx_init_one().
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Split off pdc20270_get_dev2() helper from init_setup_pdc20270().

* Merge init_setup_{pdcnew,pdc20270,pdc20276}() into pdc202new_init_one().

While at it:

* Change KERN_ level of interrupt fixup message from KERN_WARNING to KERN_INFO.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Split off hpt{374,371,366}_init() helper from init_setup_hpt{374,371,366}().

* Merge init_setup_{374,372n,371,372a,302,366}() into hpt366_init_one().

While at it:

* Use "HPT36x" name for HPT366/HPT368 chipsets.

* Add .chip_name to struct hpt_info and use it to set set d->name.

* Convert .max_ultra in struct hpt_info to .udma_mask and use it to set
  d->udma_mask.

* Fix hpt302 to use HPT302_ALLOW_ATA133_6 define.

* Change HPT366/HPT374 interrupt fixup message from KERN_WARNING to KERN_INFO.

* Use the second hpt366_chipsets[] entry for HPT37x chipsets using HPT36x PCI
  device ID and fix .enablebits/.host_flags for HPT36x hpt366_chipsets[] entry.

* Bump driver version.

Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Merge init_setup_{cmd64x,cmd646}() into cmd64x_init_one().

Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Merge init_setup_{aec62xx,aec6x80}() into aec62xx_init_one().

While at it:

* Use id->driver_data instead of dev->device.

* Use ATA_UDMA6 define.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

v2:
- bump host driver versions (as suggested by Sergei)
- use I/O ops directly in drivers/ide/setup-pci.c

Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Some places were using PCI_CLASS_REVISION instead of PCI_REVISION_ID so
they were not converted by commit 44c10138.

Cc: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Auke Kok <auke-jan.h.kok@intel.com>
Cc: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add ->mwdma_mask and ->swdma_mask to ide_pci_device_t.

* Set ide_hwif_t DMA masks using DMA masks from ide_pci_device_t in
  setup-pci.c::ide_pci_setup_ports() (iff DMA base is valid and ->init_hwif
  method may still override them).

* Convert IDE PCI host drivers to use ide_pci_device_t DMA masks.

While at it:

* Use ATA_{UDMA,MWDMA,SWDMA}* defines.

* hpt34x.c: add separate ide_pci_device_t instances for HPT343 and HPT345.

* serverworks.c: fix DMA masks being set before checking DMA base.

v2:
* Add missing masks to DECLARE_GENERIC_PCI_DEV() macro.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Documentation doesn't mention SWDMA and moreover all timings used
for SWDMA modes were over-clocked when compared to ATA spec.
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add IDE_HFLAG_NO_LBA48[_DMA] host flags, use it instead of hwif->no_lba48[_dma]
and then remove no longer needed hwif->no_lba48[_dma].  As a side-effect
this change fixes hwif->no_lba48_dma not being restored by ide_hwif_restore().
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Make ide_pci_device_t.host_flags u32 and add IDE_HFLAG_CS5520 host flag.

* Pass ide_pci_device_t *d to setup-pci.c::ide_get_or_set_dma_base()
  and use d->name instead of hwif->cds->name.

* Set IDE_HFLAG_CS5520 host flag in cs5520 host driver and use it in
  ide_get_or_set_dma_base() to find out which PCI BAR to use, remove no longer
  needed cs5520.c::cs5520_init_setup_dma() and ide_pci_device_t.init_setup_dma.

  This fixes PCI bus-mastering not being checked for CS5510/CS5520 hosts.

v2:
* It is wrong to check simplex bits on CS5510/CS5520 as v1 did.
  (Noticed by Alan).

Cc: Alan Cox <alan@lxorguk.ukuu.org.uk>
Cc: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add IDE_HFLAG_NO_{DMA,AUTODMA} host flags.  Convert all host drivers using
ide_pci_device_t to use these flags instead of d->autodma and then remove no
longer needed d->autodma.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add IDE_HFLAG_BOOTABLE host flag and IDE_HFLAG_OFF_BOARD define.  Convert
all host drivers using ide_pci_device_t to use IDE_HFLAG_{BOOTABLE,OFF_BOARD}
instead of d->bootable and then remove no longer needed d->bootable.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Add IDE_HFLAG_NO_ATAPI_DMA host flag and set it in host drivers which
don't support ATAPI DMA.  Then remove no longer needed hwif->atapi_dma.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* Add DECLARE_GENERIC_PCI_DEV() macro to generic IDE PCI host driver
  and use it to cleanup generic_chipsets[].

* Remove dead/obsolete code while at it.
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The cs5535 uses an incorrect construct to access the other drive of a pair,
causing it to access beyond an array boundary on the secondary interface.

This fixes it by using the new ide_get_paired_drive() helper instead.

Bart: patch description fixes
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andrew Morton <akpm@osdl.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

The siimage uses an incorrect construct to access the other drive of a pair,
causing it to access beyond an array boundary on the secondary interface.

This fixes it by using the new ide_get_paired_drive() helper instead.

Bart: patch description fixes
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andrew Morton <akpm@osdl.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

This adds a helper to get to the "other" drive on a pair connected
to a given hwif.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Andrew Morton <akpm@osdl.org>
Acked-by: Sergei Shtylyov <sshtylyov@ru.mvista.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <bzolnier@gmail.com>

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
  [IA64] fix non-numa build

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/ericvh/v9fs:
  9p: remove sysctl
  9p: fix bad kconfig cross-dependency
  9p: soften invalidation in loose_mode
  9p: attach-per-user
  9p: rename uid and gid parameters
  9p: define session flags
  9p: Make transports dynamic

arch/ia64/kernel/machine_kexec.c: In function `arch_crash_save_vmcoreinfo':
arch/ia64/kernel/machine_kexec.c:131: error: `pgdat_list' undeclared (first use in this function)
arch/ia64/kernel/machine_kexec.c:131: error: (Each undeclared identifier is reported only once
arch/ia64/kernel/machine_kexec.c:131: error: for each function it appears in.)
arch/ia64/kernel/machine_kexec.c:134: error: `node_memblk' undeclared (first use in this function)
arch/ia64/kernel/machine_kexec.c:135: error: `NR_NODE_MEMBLKS' undeclared (first use in this function)
arch/ia64/kernel/machine_kexec.c:136: error: invalid application of `sizeof' to incomplete type `node_memblk_s'
arch/ia64/kernel/machine_kexec.c:137: error: dereferencing pointer to incomplete type
arch/ia64/kernel/machine_kexec.c:138: error: dereferencing pointer to incomplete type
make[1]: *** [arch/ia64/kernel/machine_kexec.o] Error 1
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Tony Luck <tony.luck@intel.com>