Changes to use the 64 byte FIFO depth and fix the issue
by clearing the txempty interrupt in isr status for tx
after filling in data in start_tx function
Signed-off-by: Suneel Garapati <suneelg@xilinx.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This allows KDB/KGDB to run.
Signed-off-by: Vlad Lungu <vlad.lungu@windriver.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The Cadence UART does not do break detection, even if the
datasheet says it does. This patch adds break detection in
software (tested in 8N1 mode only) and enables SYSRQ,
allowing for Break-g to enter KDB and all the other goodies.
Signed-off-by: Vlad Lungu <vlad.lungu@windriver.com>
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the device managed interface for memory allocation, simplifying
error paths.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the device managed interface for clocks, simplifying error paths.
Signed-off-by: Soren Brinkmann <soren.brinkmann@xilinx.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

On older SoC, the "name" field is not filled in the register map.
Fix the way to figure out if the serial port is an uart or an usart for these
older products (with corresponding properties).
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Since commit 055560b0 (serial: at91:
distinguish usart and uart) the older products which do not have a
name field in their register map are unable to use their serial output.
As the main console output is usually the serial interface (aka DBGU) it
is pretty unfortunate.
So, instead of failing during probe() we just silently configure the serial
peripheral as an uart. It allows us to use these serial outputs.
The proper solution is proposed in another patch.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This adds support for Fintek's 4, 8, and 12 port PCIE serial cards.

Thanks to Fintek for the sample devices, and the spec needed in order to
implement this.

Cc: Amanda Ying <amanda_ying@fintek.com.tw>
Cc: Felix Shih <felix_shih@fintek.com.tw>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

I worried that the delay of the sdma_run_channel0() maybe too long for
interrupt context, so I added the workqueues for RX/TX DMA.

But tested with bluetooth device, I find that the delay of sdma_run_channel0()
is about 8us (tested in imx6dl sabreauto board). I think the delay
is acceptable.

This patch removes the RX/TX workqueues for DMA, it makes the
code more clear.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Use the dmaengine_tx_status to simplify the code, do not change any logic.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

When the (xmit->tail > xmit->head) is true and the xmit->head is 0,
we only need one DMA scatterlist in actually. Current code uses two DMA
scatterlists in this case, this is obviously wrong.

This patch fixes it.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Assume the following situation:

  If the DMA is enabled, and the a TX DMA operation is working,
But we have not issued the TX DMA operation (or we have issued the
TX DMA operation with dma_async_issue_pending(), but the DMA has not
started to move the data from the memory to the TXFIFO).

At this time, we may get the wrong status of the transmitter when we
call the imx_tx_empty. In such situation, only check the USR2_TXDC
does not enough for us.

This patch checks the DMA's situation, and return 0 when the TX DMA is
working.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The current driver does not implement the flush_buffer hook for
uart_ops. When we enable the DMA for the driver, and test it with Bluetooth,
we may meet the following bug for TX:

    [1] User application may call the flush operation at any time.
        The uart_flush_buffer() calls the uart_circ_clear() to set
        the xmit->head and xmit->tail with 0.

    [2] The TX DMA callback can be called at any time too.
        The dma_tx_call() will update the xmit->tail.

    If [2] occurs just after the [1], we will get the wrong xmit->tail.

This patch implements the flush_buffer hook to fix this issue.
Signed-off-by: Huang Shijie <b32955@freescale.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This deletes the .set_wake() callback in the struct uart_ops.
Apparently this has been unused since pre-git times. In the
old-2.6-bkcvs it is deleted as part of a changeset removing
the PM_SET_WAKEUP from pm_request_t which is since also deleted
from the kernel.

The apropriate way to set wakeups in the kernel is to have a
code snippet like this in .suspend() or .runtime_suspend()
callbacks:

static int foo_suspend(struct device *dev)
{
	if (device_may_wakeup(dev)) {
		/* Enable wakeups, set internal states */
	}
}

This specific callback is not coming back.

Cc: Rafael J. Wysocki <rjw@sisk.pl>
Cc: Len Brown <len.brown@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Cc: Dmitry Artamonow <mad_soft@inbox.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This callback is gone and not coming back, so will not be
supported later.

Cc: Johan Hovold <jhovold@gmail.com>
Acked-by: Darren Hart <dvhart@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This callback is gone and not coming back, so will not be
supported later.

Cc: Gerhard Sittig <gsi@denx.de>
Cc: Anatolij Gustschin <agust@denx.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This callback is unused by the serial core since pre-git days
and is not coming back. Delete it. Enabling wakeup on the
SA1100 platforms should be done in the suspend() callback
so the platform hook is left in the serial port struct for
later enablement.

Cc: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This callback is unused by the serial core since pre-git days
and is not coming back. Delete it. Enabling wakeup on the
OMAP serial driver is done through other runpaths these days.

Cc: Tony Lindgren <tony@atomide.com>
Cc: Kevin Hilman <khilman@deeprootsystems.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

test echo_buf() result for ECHO_OP_START
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Acked-by: Peter Hurley <peter@hurleysoftware.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

These aren't necessary after switch and while blocks.
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

There is a race between termios configuration and xmit that can cause the
intel_mid_ssp_spi driver to stall.

Serializing spi transactions fixes the problem.
Signed-off-by: Bin Gao <bin.gao@intel.com>
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We should check the validity of the irq number before calling
disable_irq() and enable_irq() in the suspend/resume function,
as "max->irq == 0" means the irq is not enabled for max3110
device, otherwise it will hurt device whose irq number is really 0.
Signed-off-by: Feng Tang <feng.tang@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Add calls to clk_prepare and unprepare so that EMMA Mobile EV2 can
migrate to the common clock framework.
Signed-off-by: Shinya Kuribayashi <shinya.kuribayashi.px@renesas.com>
[takashi.yoshii.ze@renesas.com: edited for conflicts]
Signed-off-by: Takashi Yoshii <takashi.yoshii.zj@renesas.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Turn the initial value of sysctl kernel.sysrq (SYSRQ_DEFAULT_ENABLE)
into a Kconfig variable.

Original version by Bastian Blank <waldi@debian.org>.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

It makes more sense to enter a bitmask in hexadecimal rather than
decimal.  Sadly we can't make it read back as hexadecimal.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch proposes to remove the use of the IRQF_DISABLED flag

It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch proposes to remove the use of the IRQF_DISABLED flag

It's a NOOP since 2.6.35 and it will be removed one day.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

We want the tty fixes in this branch as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Modify the code to use current_euid(), and in_egroup_p, as in done
in fs/proc/proc_sysctl.c:test_perm()

Cc: stable@vger.kernel.org
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
Reported-by: Eric Sandeen <sandeen@redhat.com>
Signed-off-by: "Eric W. Biederman" <ebiederm@xmission.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull SCSI target fixes from Nicholas Bellinger:
 "Here are the outstanding target fixes queued up for v3.12-rc4 code.

  The highlights include:

   - Make vhost/scsi tag percpu_ida_alloc() use GFP_ATOMIC
   - Allow sess_cmd_map allocation failure fallback to use vzalloc
   - Fix COMPARE_AND_WRITE se_cmd->data_length bug with FILEIO backends
   - Fixes for COMPARE_AND_WRITE callback recursive failure OOPs + non
     zero scsi_status bug
   - Make iscsi-target do acknowledgement tag release from RX context
   - Setup iscsi-target with extra (cmdsn_depth / 2) percpu_ida tags

  Also included is a iscsi-target patch CC'ed for v3.10+ that avoids
  legacy wait_for_task=true release during fast-past StatSN
  acknowledgement, and two other SRP target related patches that address
  long-standing issues that are CC'ed for v3.3+.

  Extra thanks to Thomas Glanzmann for his testing feedback with
  COMPARE_AND_WRITE + EXTENDED_COPY VAAI logic"

* git://git.kernel.org/pub/scm/linux/kernel/git/nab/target-pending:
  iscsi-target; Allow an extra tag_num / 2 number of percpu_ida tags
  iscsi-target: Perform release of acknowledged tags from RX context
  iscsi-target: Only perform wait_for_tasks when performing shutdown
  target: Fail on non zero scsi_status in compare_and_write_callback
  target: Fix recursive COMPARE_AND_WRITE callback failure
  target: Reset data_length for COMPARE_AND_WRITE to NoLB * block_size
  ib_srpt: always set response for task management
  target: Fall back to vzalloc upon ->sess_cmd_map kzalloc failure
  vhost/scsi: Use GFP_ATOMIC with percpu_ida_alloc for obtaining tag
  ib_srpt: Destroy cm_id before destroying QP.
  target: Fix xop->dbl assignment in target_xcopy_parse_segdesc_02

Pull slave-dmaengine fixes from Vinod Koul:
 "Here is the slave dmanegine fixes.  We have the fix for deadlock issue
  on imx-dma by Michael and Josh's edma config fix along with author
  change"

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dmaengine: imx-dma: fix callback path in tasklet
  dmaengine: imx-dma: fix lockdep issue between irqhandler and tasklet
  dmaengine: imx-dma: fix slow path issue in prep_dma_cyclic
  dma/Kconfig: Make TI_EDMA select TI_PRIV_EDMA
  edma: Update author email address

When DMA is enabled (with hardware flow control enabled) the FIFO size
must be set to the size of the DMA buffer, as this is the size the tty
subsystem can use.
Signed-off-by: Hector Palacios <hector.palacios@digi.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull btrfs fixes from Chris Mason:
 "This is a small collection of fixes, including a regression fix from
  Liu Bo that solves rare crashes with compression on.

  I've merged my for-linus up to 3.12-rc3 because the top commit is only
  meant for 3.12.  The rest of the fixes are also available in my master
  branch on top of my last 3.11 based pull"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mason/linux-btrfs:
  btrfs: Fix crash due to not allocating integrity data for a bioset
  Btrfs: fix a use-after-free bug in btrfs_dev_replace_finishing
  Btrfs: eliminate races in worker stopping code
  Btrfs: fix crash of compressed writes
  Btrfs: fix transid verify errors when recovering log tree

Pull GPIO fixes from Linus Walleij:
 "Two patches for the OMAP driver, dealing with setting up IRQs properly
  on the device tree boot path"

* tag 'gpio-v3.12-2' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
  gpio/omap: auto-setup a GPIO when used as an IRQ
  gpio/omap: maintain GPIO and IRQ usage separately

Pull USB fixes from Greg KH:
 "Here are none fixes for various USB driver problems.  The majority are
  gadget/musb fixes, but there are some new device ids in here as well"

* tag 'usb-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb:
  usb: chipidea: add Intel Clovertrail pci id
  usb: gadget: s3c-hsotg: fix can_write limit for non-periodic endpoints
  usb: gadget: f_fs: fix error handling
  usb: musb: dsps: do not bind to "musb-hdrc"
  USB: serial: option: Ignore card reader interface on Huawei E1750
  usb: musb: gadget: fix otg active status flag
  usb: phy: gpio-vbus: fix deferred probe from __init
  usb: gadget: pxa25x_udc: fix deferred probe from __init
  usb: musb: fix otg default state

Pull tty fixes from Greg KH:
 "Here are two tty driver fixes for 3.12-rc4.

  One fixes the reported regression in the n_tty code that a number of
  people found recently, and the other one fixes an issue with xen
  consoles that broke in 3.10"

* tag 'tty-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
  xen/hvc: allow xenboot console to be used again
  tty: Fix pty master read() after slave closes

Pull staging fixes from Greg KH:
 "Here are 4 tiny staging and iio driver fixes for 3.12-rc4.  Nothing
  major, just some small fixes for reported issues"

* tag 'staging-3.12-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
  staging: comedi: ni_65xx: (bug fix) confine insn_bits to one subdevice
  iio:magnetometer: Bugfix magnetometer default output registers
  iio: Remove debugfs entries in iio_device_unregister()
  iio: amplifiers: ad8366: Remove regulator_put

When btrfs creates a bioset, we must also allocate the integrity data pool.
Otherwise btrfs will crash when it tries to submit a bio to a checksumming
disk:

 BUG: unable to handle kernel NULL pointer dereference at 0000000000000018
 IP: [<ffffffff8111e28a>] mempool_alloc+0x4a/0x150
 PGD 2305e4067 PUD 23063d067 PMD 0
 Oops: 0000 [#1] PREEMPT SMP
 Modules linked in: btrfs scsi_debug xfs ext4 jbd2 ext3 jbd mbcache
sch_fq_codel eeprom lpc_ich mfd_core nfsd exportfs auth_rpcgss af_packet
raid6_pq xor zlib_deflate libcrc32c [last unloaded: scsi_debug]
 CPU: 1 PID: 4486 Comm: mount Not tainted 3.12.0-rc1-mcsum #2
 Hardware name: Bochs Bochs, BIOS Bochs 01/01/2011
 task: ffff8802451c9720 ti: ffff880230698000 task.ti: ffff880230698000
 RIP: 0010:[<ffffffff8111e28a>]  [<ffffffff8111e28a>] mempool_alloc+0x4a/0x150
 RSP: 0018:ffff880230699688  EFLAGS: 00010286
 RAX: 0000000000000001 RBX: 0000000000000000 RCX: 00000000005f8445
 RDX: 0000000000000001 RSI: 0000000000000010 RDI: 0000000000000000
 RBP: ffff8802306996f8 R08: 0000000000011200 R09: 0000000000000008
 R10: 0000000000000020 R11: ffff88009d6e8000 R12: 0000000000011210
 R13: 0000000000000030 R14: ffff8802306996b8 R15: ffff8802451c9720
 FS:  00007f25b8a16800(0000) GS:ffff88024fc80000(0000) knlGS:0000000000000000
 CS:  0010 DS: 0000 ES: 0000 CR0: 000000008005003b
 CR2: 0000000000000018 CR3: 0000000230576000 CR4: 00000000000007e0
 Stack:
  ffff8802451c9720 0000000000000002 ffffffff81a97100 0000000000281250
  ffffffff81a96480 ffff88024fc99150 ffff880228d18200 0000000000000000
  0000000000000000 0000000000000040 ffff880230e8c2e8 ffff8802459dc900
 Call Trace:
  [<ffffffff811b2208>] bio_integrity_alloc+0x48/0x1b0
  [<ffffffff811b26fc>] bio_integrity_prep+0xac/0x360
  [<ffffffff8111e298>] ? mempool_alloc+0x58/0x150
  [<ffffffffa03e8041>] ? alloc_extent_state+0x31/0x110 [btrfs]
  [<ffffffff81241579>] blk_queue_bio+0x1c9/0x460
  [<ffffffff8123e58a>] generic_make_request+0xca/0x100
  [<ffffffff8123e639>] submit_bio+0x79/0x160
  [<ffffffffa03f865e>] btrfs_map_bio+0x48e/0x5b0 [btrfs]
  [<ffffffffa03c821a>] btree_submit_bio_hook+0xda/0x110 [btrfs]
  [<ffffffffa03e7eba>] submit_one_bio+0x6a/0xa0 [btrfs]
  [<ffffffffa03ef450>] read_extent_buffer_pages+0x250/0x310 [btrfs]
  [<ffffffff8125eef6>] ? __radix_tree_preload+0x66/0xf0
  [<ffffffff8125f1c5>] ? radix_tree_insert+0x95/0x260
  [<ffffffffa03c66f6>] btree_read_extent_buffer_pages.constprop.128+0xb6/0x120
[btrfs]
  [<ffffffffa03c8c1a>] read_tree_block+0x3a/0x60 [btrfs]
  [<ffffffffa03caefd>] open_ctree+0x139d/0x2030 [btrfs]
  [<ffffffffa03a282a>] btrfs_mount+0x53a/0x7d0 [btrfs]
  [<ffffffff8113ab0b>] ? pcpu_alloc+0x8eb/0x9f0
  [<ffffffff81167305>] ? __kmalloc_track_caller+0x35/0x1e0
  [<ffffffff81176ba0>] mount_fs+0x20/0xd0
  [<ffffffff81191096>] vfs_kern_mount+0x76/0x120
  [<ffffffff81193320>] do_mount+0x200/0xa40
  [<ffffffff81135cdb>] ? strndup_user+0x5b/0x80
  [<ffffffff81193bf0>] SyS_mount+0x90/0xe0
  [<ffffffff8156d31d>] system_call_fastpath+0x1a/0x1f
 Code: 4c 8d 75 a8 4c 89 6d e8 45 89 e0 4c 8d 6f 30 48 89 5d d8 41 83 e0 af 48
89 fb 49 83 c6 18 4c 89 7d f8 65 4c 8b 3c 25 c0 b8 00 00 <48> 8b 73 18 44 89 c7
44 89 45 98 ff 53 20 48 85 c0 48 89 c2 74
 RIP  [<ffffffff8111e28a>] mempool_alloc+0x4a/0x150
  RSP <ffff880230699688>
 CR2: 0000000000000018
 ---[ end trace 7a96042017ed21e2 ]---
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Signed-off-by: Josef Bacik <jbacik@fusionio.com>
Signed-off-by: Chris Mason <chris.mason@fusionio.com>