Bert Kenward says:

====================
sfc: SFN8000 support improvements

This series improves support for the recently released SFN8000 series
of adapters. Specifically, it retrieves interrupt moderation timer
settings directly from the adapter and uses those settings. It also
uses a new event queue initialisation interface, allowing specification
of a performance objective rather than enabling individual flags.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

On SFN8000 series adapters the MC provides a method to get the timer
quantum and the maximum timer setting. We revert to the old values if the
new call is unavailable.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

SFN8000-series NICs require a new method of setting interrupt moderation,
via MCDI. This is indicated by a workaround flag. This new MCDI command
takes an explicit time value rather than a number of ticks. It therefore
makes sense to also store the moderation values in terms of time, since
that is what the ethtool interface is interested in.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Rather than explicitly specifying flags we can now specify a desired
performance target to the firmware, ie higher throughput or lower latency.
For now we use the default "auto" configuration.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since these critical sections protected by page_lock are all entered
from the user context or bottom half context, they can be replaced
with the spin_lock() or spin_lock_bh instead of spin_lock_irqsave().
Signed-off-by: Sean Wang <sean.wang@mediatek.com>
Acked-by: John Crispin <john@phrozen.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a driver for the ENA family of networking devices.
Signed-off-by: Netanel Belgazal <netanel@annapurnalabs.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Kedareswara rao Appana says:

====================
net: phy: Add xilinx gmiitorgmii converter support

The Gigabit Media Independent Interface (GMII) to Reduced Gigabit Media
Independent Interface (RGMII) core provides the RGMII between RGMII-compliant
Ethernet physical media devices (PHY) and the Gigabit Ethernet controller.
This core can be used in all three modes of operation(10/100/1000 Mb/s).
The Management Data Input/Output (MDIO) interface is used to configure the
Speed of operation. This core can switch dynamically between the three
Different speed modes by configuring the conveter register through mdio write.

The conveter sits b/w the MAC and external phy like below

MACB <==> GMII2RGMII <==> RGMII_PHY

        MDIO    <========> GMII2RGMII
MCAB <=======>
                <========> RGMII

Using MAC MDIO bus we can access both the converter and the external PHY.
We need to program the line speed of the converter during run time based
On the external phy negotiated speed.

This patch series does the below
---> Add mask for Control register 10Mbps speed.
---> Add support for xilinx gmiitorgmii converter.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for gmiitorgmii converter.

The GMII to RGMII IP core provides the Reduced Gigabit Media
Independent Interface (RGMII) between Ethernet physical media
Devices and the Gigabit Ethernet controller. This core can
Switch dynamically between the three different speed modes of
Operation by configuring the converter register through mdio write.

MDIO interface is used to set operating speed of Ethernet MAC.

This converter sits between the MAC and the external phy
MAC <==> GMII2RGMII <==> RGMII_PHY
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Device-tree binding documentation for xilinx gmiitorgmii converter.
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds mask for the Control register
10Mbps speed.
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

The private structure contain a pointer to phydev, but the structure
net_device already contain such pointer. So we can remove the pointer
phy_dev in the private structure, and update the driver to use the
one contained in struct net_device.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Tested-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: David S. Miller <davem@davemloft.net>

The commit 555c8a86 ("bpf: avoid stack copy and use skb ctx for event output")
started using 20 of initially reserved upper 32-bits of 'flags' argument
in bpf_perf_event_output(). Adjust corresponding prototype in samples/bpf/bpf_helpers.h
Signed-off-by: Adam Barth <arb@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Daniel Borkmann <daniel@iogearbox.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds support for 64 bit addressing and BDs.
-> Enable 64 bit addressing in DMACFG register.
-> Set DMA mask when design config register shows support for 64 bit addr.
-> Add new BD words for higher address when 64 bit DMA support is present.
-> Add and update TBQPH and RBQPH for MSB of BD pointers.
-> Change extraction and updation of buffer addresses to use
64 bit address.
-> In gem_rx extract address in one place insted of two and use a
separate flag for RXUSED.
Signed-off-by: Harini Katakam <harinik@xilinx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the driver implementation for ethtool link_ksettings
callbacks. qed driver now defines/uses the qed specific masks for
representing link capability values. qede driver maps these values to
to new link modes defined by the kernel implementation of link_ksettings.

Please consider applying this to 'net-next' branch.
Signed-off-by: Sudarsana Reddy Kalluru <sudarsana.kalluru@qlogic.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Ivan Khoronzhuk says:

====================
net: ethernet: ti: cpsw: split driver data and per ndev data

In dual_emac mode the driver can handle 2 network devices. Each of them can use
its own private data and common data/resources. This patchset splits common driver
data/resources and private per net device data.
It leads to:
- reduce memory usage
- increase code readability
- allows add a bunch of simplification
- create prerequisites to add multi-channel support,
  when channels are shared between net devices

Doesn't have bad impact on performance.
v2: https://lkml.org/lkml/2016/8/6/108

Since v2:
- removed patch:
  net: ethernet: ti: cpsw: fix int dbg message
- replaced patch:
  "net: ethernet: ti: cpsw: remove redundant check in napi poll"
  on "net: ethernet: ti: cpsw: remove intr dbg msg from poll handlers"
- removed macro "cpsw_get_slave_ndev"
- corrected some commits

Since v1:
- added several patch improvements
- avoided variable reordering in structures
- removed static variable for common function
- split big patch on several patches:
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The ale, cpts, version, rx_packet_max, bus_freq, interrupt pacing
parameters are common per net device that uses the same h/w. So,
move them to common driver structure.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The napi structs are common for both net devices in dual_emac
mode, In order to not hold duplicate links to them, move to
cpsw_common.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

These data are common for net devs in dual_emac mode. No need to hold
it for every priv instance, so move them under cpsw_common.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The irq data are common for net devs in dual_emac mode. So no need to
hold these data in every priv struct, move them under cpsw_common.
Also delete irq_num var, as after optimization it's not needed.
Correct number of irqs to 2, as anyway, driver is using only 2,
at least for now.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Every net device private struct holds links to shared cpdma resources.
No need to save and every time synchronize these resources per net dev.
So, move it to common driver struct.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The pointers on h/w registers are common for every cpsw_private
instance, so no need to hold them for every ndev.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

No need to hold pdev link when only dev is needed.
This allows to simplify a bunch of cpsw->pdev->dev now and farther.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch simply create holder for common data and as a start moves
pdev var to it.
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

No need to check const slave num in runtime for every packet,
and ndev for slaves w/o ndev is anyway NULL. So remove redundant
check and macro.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need to hold link to clk, it's used only once
while probe.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is no need in priv here.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

At poll handler no possibility to figure out which network device is
handling packets, as cpdma channels are common for both network
devices in dual_emac mode. Currently, the messages are printed only
for one device, in fact, there is two. This print msg is incorrect
and seems is not very useful, so drop it from poll handler.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

As second net dev is created only in case of dual_emac mode, port
number can be figured out in simpler way. Also no need to pass
redundant ndev struct.
Reviewed-by: Mugunthan V N <mugunthanvnm@ti.com>
Reviewed-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The PPTP is encapsulated by GRE header with that GRE_VERSION bits
must contain one. But current GRE RPS needs the GRE_VERSION must be
zero. So RPS does not work for PPTP traffic.

In my test environment, there are four MIPS cores, and all traffic
are passed through by PPTP. As a result, only one core is 100% busy
while other three cores are very idle. After this patch, the usage
of four cores are balanced well.
Signed-off-by: Gao Feng <fgao@ikuai8.com>
Reviewed-by: Philip Prindeville <philipp@redfish-solutions.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jiri Kosina says:

====================
Convert qdisc linked list into a hashtable

This is a respin of the v6 of the original patch [1], split into two-patch
series as requested by davem; first patch fixes all symbol conflicts
that'd happen once netdevice.h starts to include hashtable.h, the second
one performs the actual switch to hashtable.

I've preserved Cong's Reviewed-by:, as code-wise this series is identical
to the original v6 of the patch.

[1] lkml.kernel.org/r/alpine.LNX.2.00.1608011220580.22028@cbobk.fhfr.pm
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Convert the per-device linked list into a hashtable. The primary
motivation for this change is that currently, we're not tracking all the
qdiscs in hierarchy (e.g. excluding default qdiscs), as the lookup
performed over the linked list by qdisc_match_from_root() is rather
expensive.

The ultimate goal is to get rid of hidden qdiscs completely, which will
bring much more determinism in user experience.
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

This is a preparatory patch for converting qdisc linked list into a
hashtable. As we'll need to include hashtable.h in netdevice.h, we first
have to make sure that this will not introduce symbol conflicts for any of
the netdevice.h users.
Reviewed-by: Cong Wang <xiyou.wangcong@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

The patch 'ravb: add sleep PM suspend/resume support' used incorrect
function names containing 'runtime' for the suspend and resume
functions.
Reported-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Acked-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

ic_close_devs() calls kfree() for all devices's ic_device. Since commit
2647cffb ("net: ipconfig: Support using "delayed" DHCP replies")
the active device's ic_device is still used however to print the
ipconfig summary which results in an oops if the memory is already
changed. So delay freeing until after the autoconfig results are
reported.

Fixes: 2647cffb ("net: ipconfig: Support using "delayed" DHCP replies")
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Tested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>

The interface would not function after the system had been woken up
after have been suspended (echo mem > /sys/power/state) cycle. The
reason for this is that all device registers have been reset to its
default values. This patch adds sleep suspend and resume functions that
detached the interface at suspend and restore the registers and reattach
the interface at resume.

Only the registers that are only configured at probe time needs to be
explicitly restored by the resume handler. All other registers are
reconfigured by either reopening the device in the resume handler (if
the device was running when the system was suspended) or when the
interface is opened by a user at a later time.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: David S. Miller <davem@davemloft.net>

The b53_io_ops structures are never modified, so declare them as const.

Done with the help of Coccinelle.
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>