- 17 Jun, 2013 40 commits
-
-
Huang Shijie authored
The WEIM(Wireless External Interface Module) works like a bus. You can attach many different devices on it, such as NOR, onenand. In the case of i.MX6q-sabreauto, the NOR is connected to WEIM. This patch also adds the devicetree binding document. The driver only works when the devicetree is enabled. Signed-off-by:
Huang Shijie <b32955@freescale.com> Acked-by:
Sascha Hauer <s.hauer@pengutronix.de> Signed-off-by:
Shawn Guo <shawn.guo@linaro.org>
-
Markus Niebel authored
Add missing pin config Signed-off-by:
Markus Niebel <Markus.Niebel@tqs.de> Signed-off-by:
Steffen Trumtrar <s.trumtrar@pengutronix.de> Signed-off-by:
-
Steffen Trumtrar authored
use NO_PAD_CTL / 0x80000000 instead of 0x10000 to prevent misconfigured pads Signed-off-by:
-
Markus Niebel authored
Signed-off-by:
-
Markus Niebel authored
Add properties to make use of pca9554 gpio expander. Signed-off-by:
-
Markus Niebel authored
Enable the sgtl5000 found on MBa53 mainboard. Also enable audio muxer and ssi, which are needed for sound to work. Signed-off-by:
Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by:
-
Philipp Zabel authored
Enable tve on MBa53. Signed-off-by:
-
Sascha Hauer authored
As the displays are optional and we have more than one, also set the status of the parallel display and the ldb to disabled. Signed-off-by:
-
Michael Olbrich authored
Signed-off-by:
Michael Olbrich <m.olbrich@pengutronix.de> Signed-off-by:
-
Steffen Trumtrar authored
Add WP/CD pinctrl for esdhc2. Also, add vmmc-supply for esdhc2. Signed-off-by:
-
Philipp Zabel authored
This adds the Television Encoder (TVEv2) device tree node to the i.MX53 dtsi. Signed-off-by:
-
Philipp Zabel authored
I2S_MCLK is moved from pad GPIO19 to GPIO0, which can be muxed to the ssi_ext1 clock signal. #SYSTEM_DOWN is moved from pad GPIO0 to GPIO19. Add #PHY_RESET and LCD_CONTRAST. Signed-off-by:
-
Philipp Zabel authored
BIT(31) is NO_PAD_CTL, not BIT(16) Signed-off-by:
-
Sascha Hauer authored
It's active high, not active low. Signed-off-by:
-
Alexander Shiyan authored
Patch adds initial dts for Phytec PCM970 Rapid development kit. - Added definition for UART0 and UART1. - Added additional SPI chipselect which used on RDK for ZegBee module. Signed-off-by:
Alexander Shiyan <shc_work@mail.ru> Acked-by:
-
Alexander Shiyan authored
UART1 and UART2 can be unused on some designs with PCM038 module. Remove these definitions from basic dts and lets choose user only necessary UARTs in custom designs. Keep UART0 for using this one as boot console, but since we have not way to disable usage RTSCTS signals, remove this parameter for UART0. Signed-off-by:
-
Alexander Shiyan authored
PCM038 dts can be used as base for development kit board or any custom PCB designs. Renames this file to match functionality. Signed-off-by:
-
Alexander Shiyan authored
FEC (KSZ8001L) reset pin is connected to GPIOC30. Add this definition to dts. Signed-off-by:
-
Jingchang Lu authored
Add initial Freescale Vybrid VF610 Tower board support with uart and fec enabled. Signed-off-by:
Jingchang Lu <b35083@freescale.com> Signed-off-by:
-
Jingchang Lu authored
Add SoC level device tree source for Freescale Vybrid VF610. Signed-off-by:
-
Jonas Andersson authored
Add a group to the fec pinctrl, for use with MII interface. Signed-off-by:
Jonas Andersson <jonas@microbit.se> Signed-off-by:
-
Jonas Andersson authored
Add ecspi2 pinctrl. Signed-off-by:
-
Jonas Andersson authored
Add a group to the cspi pinctrl. Signed-off-by:
-
Rogerio Pimentel authored
Add support for CLAA WVGA display for i.MX53 QSB. Signed-off-by:
Rogerio Pimentel <rogerio.pimentel@freescale.com> Acked-by:
-
Gwenhael Goavec-Merou authored
Signed-off-by:
Gwenhael Goavec-Merou <gwenhael.goavec-merou@armadeus.com> Signed-off-by:
-
Dirk Behme authored
With the commit 7f217794 (mmc: dt: Consolidate DT bindings), the device tree properties used by various device drivers for SD/MMC host controllers were standardized. One of the changes was that the property "fsl,card-wired", previously used by the Freescale driver, was replaced with "non-removable". Fix the example documentation regarding this. Signed-off-by:
Dirk Behme <dirk.behme@de.bosch.com> Signed-off-by:
-
Shawn Guo authored
There is a redundant ocotp node. Remove it. Signed-off-by: -
Shawn Guo authored
There is a redundant label on usbmisc node. Remove it. Signed-off-by: -
Shawn Guo authored
Add initial imx6sl-evk board support with uart, usdhc and fec enabled. Signed-off-by: -
Shawn Guo authored
Add SoC level device tree source for imx6sl. Signed-off-by: -
Dirk Behme authored
Configure the data and tag latency for the L2 cache. This improves the system performance. This configuration is taken from Freescale's kernel patch "ENGR00153601 [MX6]Adjust L2 cache parameter" [1] which does writel(0x132, IO_ADDRESS(L2_BASE_ADDR + L2X0_TAG_LATENCY_CTRL)); writel(0x132, IO_ADDRESS(L2_BASE_ADDR + L2X0_DATA_LATENCY_CTRL)); In this patch we are doing the same via the device tree. Signed-off-by:
-
Huang Shijie authored
Since the SPI/NOR has pin conflict with the WEIM NOR, we disable the spi/nor by default. Signed-off-by:
-
Huang Shijie authored
The SPI/NOR needs this gpio for CS. So add this gpio in the hog pinctrl. Signed-off-by:
-
Huang Shijie authored
The SPI/NOR needs this gpio for CS. So add this gpio in the hog pinctrl. Signed-off-by:
-
Huang Shijie authored
Signed-off-by:
-
Huang Shijie authored
enable the gpmi-nand for imx6q-sabreauto and imx6qdl-sabreauto boards. Signed-off-by:
-
Huang Shijie authored
add the pinctrl item for gpmi-nand. Signed-off-by:
-
Huang Shijie authored
The gpmi does not use the MX6Q_PAD_NANDF_CS2__NAND_CE2_B and MX6Q_PAD_NANDF_CS3__NAND_CE3_B. Just remove them. Signed-off-by:
-
Alexander Shiyan authored
Added SPI node and PMIC MC13783 (spi0.0) to imx27-phytec-phycore DT file. Signed-off-by:
-
Alexander Shiyan authored
Add aliases to determine the proper SPI bus number. Signed-off-by:
-
