This patch fixes vibrator playing incoherently, when driven
with audio. There is something wrong in switch 3 at
H-bridge and VIBRA_SET still affects PWM generator.
Slowest value fixes things.
Signed-off-by: Jari Vanhala <ext-jari.vanhala@nokia.com>
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The CS4270 codec features an de-emphasis filter for compensation of
audio material filtered by an 50/15 uS algorithm. Not sure whether we
should always enable it for 44100Hz sampling frequency, but it should at
least be configurable by the user.
Signed-off-by: Daniel Mack <daniel@caiaq.de>
Acked-by: Timur Tabi <timur@freescale.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Fix up some comments, remove all enable_pin() calls (edge widgets
are all enabled by default) and mark the microphone as disabled by
default since it requires a resistor fit to connect it.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

codec_muted is missleading, change it to apll_enabled,
which is what it is doing: enabing and disabling the APLL.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Since ASoC core now handling the codec bias differently
there is no need to do the tracking of bypass switch states
anymore.

Handling of the common bit for analog loopbacks is done with
DAPM_SUPPLY for the bypass paths.

Now this bit is only enabled when there is a complete analog
bypass path, compared to the previous implementation, when the
global switch was enabled if there were any of the analog
bypass switch was on (regardless if there were complete path or
not)
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Change the way how the twl4030 soc codec driver is
loaded/probed.
Use the device probing via tlw4030_codec MFD device.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Remove the register descriptions from the twl4030.h file and use
the linux/mfd/twl4030-codec.h instead, which has the codec
related register descriptions also.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Add needed platform data for the twl4030_codec MFD on boards,
where the audio part of the twl4030 codec is used.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

New MFD child to twl4030 MFD device.

Reason for the twl4030_codec MFD: the vibra control is actually in the codec
part of the twl4030. If both the vibra and the audio functionality is needed
from the twl4030 at the same time, than they need to control the codec power
and APLL at the same time without breaking the other driver.
Also these two has to be able to work without the need for the other driver.

This MFD device will be used by the drivers, which needs resources
from the twl4030 codec like audio and vibra.

The platform specific configuration data is passed along to the
child drivers (audio, vibra).
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

After DMA burst mode has been introduced in sound/soc/omap/omap-pcm.c,
omap_pcm_prepare() unconditionally calls:

        omap_set_dma_src_burst_mode(prtd->dma_ch, OMAP_DMA_DATA_BURST_16);
        omap_set_dma_dest_burst_mode(prtd->dma_ch, OMAP_DMA_DATA_BURST_16);

Current implementation of those two functions found in
arch/arm/plat-ompa/dma.c doesn't support OMAP_DMA_DATA_BURST_16 on OMAP1 at
all, so they both end with BUG() on that machine. That results in
ASoC being completely unusable, at least on my OMAP5910 based Amstrad Delta.

The patch corrects the problem by not calling those two functions when run on
OMAP1 class based machines.

Created against linux-2.6.32-rc5.
Tested on Amstrad Delta.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Acked-by: Jarkko Nikula <jhnikula@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Fix the definition of DAC33_LTM field, the LTM bits in
FIFO_IRQ_MODE_B register are starting at bit 6.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Hi Mark,

Here is a patch that corrects small omissions I have found in my code.
Signed-off-by: Janusz Krzysztofik <jkrzyszt@tis.icnet.pl>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Some codec DAIs like stac9766, wm9712, wm9713, ad1980 don't register themselves
then it loses to the chance to be given a null_dai_ops in snd_soc_register_dai
if they have no ops. When functions like soc_pcm_open, soc_pcm_hw_params etc.
access the ops field in these DAIs, panic will happen.
Signed-off-by: Barry Song <21cnbao@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

If the NULL test on jack is needed, then the derefernce should be after the
NULL test.

A simplified version of the semantic match that detects this problem is as
follows (http://coccinelle.lip6.fr/):

// <smpl>
@match exists@
expression x, E;
identifier fld;
@@

* x->fld
  ... when != \(x = E\|&x\)
* x == NULL
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Codec read/write functions: wait 21us between the pokings of hardware.
Add timeouts to unbounded loops waiting for bits to change.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Verify that the correct register has been received from the codec.
Signed-off-by: Manuel Lauss <manuel.lauss@gmail.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Do not rewrite the whole register, but only update the needed
bits in set_dai_sysclk functions.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Driver for Texas Instruments TLV320DAC33 (SLAS546) low power stereo
audio DAC.

TLV320DAC33 is a stereo audio codec with integrated 24KB FIFO for low
power audio playback.

The digital interface can use I2S, DSP (A or B), Right and Left
justified formats.
DAC33 has stereo analog input, which can be bypassed to the analog
outputs.

Regarding to the internal 24KB FIFO the driver implements 'FIFO bypass'
mode (default) and nSample mode (FIFO is in use).
a) In 'FIFO bypass' mode the internal FIFO is not in use, the codec is
working synchronously as a normal codec (it needs constant stream of
data on the digital interface).

b) The nSample mode implementation uses one interrupt line from DAC33 to
the host:
Alarm threshold is set to 10ms of audio data (limit by the driver
implementation).
DAC33 will signal an interrupt, when the FIFO level goes under the
Alarm threshold.
The host will write to nSample register a value (number of stereo
samples), to tell DAC33 how many samples it should read in a burst from
the host. When the DAC33 received the number of samples, it disables the
clocks on the I2S bus. When the FIFO use again goes under the Alarm
threshold, DAC33 signals the host with an interrupt, and the process is
repeated.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
CC: Mark Brown <broonie@opensource.wolfsonmicro.com>
CC: alsa-devel@alsa-project.org
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The PM core will grow pm_link infrastructure in 2.6.33 which can be
used to implement the intended functionality of the ASoC-specific
device suspend and resume callbacks so drop them.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Remove the <plat/audio.h> include from arch/arm/plat-s3c/include/plat/audio.h
as it provides nothing to the current kernel and is not in any future plans
for the system.
Signed-off-by: Ben Dooks <ben@simtec.co.uk>
Signed-off-by: Simtec Linux Team <linux@simtec.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Access to damp_power_widgets() is assumed to be single-threaded.
Concurrent accesses to dapm_power_widgets() may result in
unpredictable behavior.

Calls from:
close_delayed_work()
soc_codec_close()
soc_pcm_prepare()
soc_suspend()
soc_resume_deferred()
to snd_soc_dapm_stream_event() do not have the codec->mutex
taken to cover the call to dapm_power_widgets(). Thus, take
the mutex in these paths also to assure single-threaded use
of dapm_power_widgets().
Signed-off-by: Eero Nurkkala <ext-eero.nurkkala@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The power for the amplifier should be handled internally
by the tpa6130a2 driver.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

- Staticise ttpa6130a2_client.
- Remove unneeded cast from void.
- Use explict NULL rather than 0.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Driver for Texas Instruments TPA6130A2 stereo headphone
amplifier.

The driver provides playback gain control and also pre-defined
DAPM_HP widgets and DAPM routings for power management.

The DAPM_HP widget names are:
"TPA6130A2 Headphone Left"
"TPA6130A2 Headphone Right"

From soc machine drivers to use with the tpa6130a2 amplifier,
the tpa6130a2_add_controls has to be called, which adds the alsa
controls and the DAPM routing needed for the tpa6130a2.
After that the machine driver can connect the codec's output
with 'TPA6130A2 Left' and 'TPA6130A2 Right':

        {"TPA6130A2 Left", NULL, "CODEC LEFT OUT"},
        {"TPA6130A2 Right", NULL, "CODEC RIGHT OUT"},

Internally the left and right channels are powered separately.
When none of the channels are needed the amplifier is powered
down:
hard power: valid GPIO number is passed within platform data
soft power: Using the software shutdown of the amplifier
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@nokia.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

The modified revision of at91sam9g20 Evaluation Kit rev. C and onwards share
with previous ones its audio connexion to Wolfson wm8731. Modify the SoC file
to extend the machine ID checking.
Signed-off-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: stable@kernel.org

These should be handled via set_tdm_slot() now and cause build
failures as-is.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Sometimes it is desirable to have a mux which does not reflect any
direct register configuration but which will instead only have an
effect implicitly (for example, as a result of changing which parts
of the device are powered up). Provide a virtual mux for this purpose.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Don't assume that enumerations are backed by registers when updating
mux power.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

We don't need to check for an event callback since we also check for
an appropriate event flag when applying mux status changes.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

Merge branch 'for-2.6.32' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound-2.6 into for-2.6.32

I'm skipping -rc2 because the -rc1 Makefile mistakenly said -rc2, so in
order to avoid confusion, I'm jumping from -rc1 to -rc3.  That way, when
'uname' (or an oops report) says 2.6.32-rc2, there's no confusion about
whether people perhaps meant -rc1 or -rc2.