Move the usb@700d0000 node to the correct place in the device tree,
ordered by unit-address.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Standardize on "pmic" as the node name for the PMIC on Tegra210 systems
and use consistent names for pinmux and GPIO hog nodes.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Device tree nodes for interrupt controllers should be named "interrupt-
controller", so rename the AGIC accordingly.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Properly indent subsequent lines so that they align with the first line.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Properly indent subsequent lines so that they align with the first line.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The AON GPIO controller on Tegra194 currently only uses a single
interrupt, so remove the extra ones.
Signed-off-by: Thierry Reding <treding@nvidia.com>

SRAM nodes should be named sram@<unit-address> to match the bindings.

While at it, also remove the unneeded, custom compatible string for
SRAM partition nodes.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The display hub on Tegra186 and Tegra194 is not a simple bus, so drop
the corresponding compatible string.
Signed-off-by: Thierry Reding <treding@nvidia.com>

It's very difficult to describe string lists that can be in arbitrary
order using the json-schema based validation tooling. Since the OS is
not going to care either way, take the easy way out and reorder these
entries to match the order defined in the bindings.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The XUSB controller doesn't need the XUSB pad controller's interrupt, so
remove it.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The address-bits and page-size properties that are currently used are
not valid properties according to the bindings. Use the address-width
and pagesize properties instead.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Use the preferred {id,vbus}-gpios over the {id,vbus}-gpio properties and
fix the ordering of compatible strings (most-specific ones should come
first).
Signed-off-by: Thierry Reding <treding@nvidia.com>

On Tegra186 and later, the BPMP is responsible for enabling/disabling
the PCIe related power supplies of the pad controller and there is no
need for the operating system to control them, so they can be removed.
Signed-off-by: Thierry Reding <treding@nvidia.com>

USB PHYs must have a #phy-cells property, so add one to the Tegra USB
PHYs which don't have one.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The external memory controller found on Tegra132 is not fully compatible
with the instantiation on Tegra124, so remove the corresponding string
from the list of compatible strings.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The sor0_out clock is required to make eDP work properly.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The host1x is not a simple bus, so drop the corresponding compatible
string.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Tuple boundaries should be marked by < and > to make it clear which
cells are part of the same tuple. This also helps the json-schema based
validation tooling to properly parse this data.

While at it, also remove the "immovable" bit from PCI addresses. All of
these addresses are in fact "movable".
Signed-off-by: Thierry Reding <treding@nvidia.com>

This panel supply is always on, so this does happen to work by accident.
Make sure to properly hook up the power supply to model the dependency
correctly and so that the panel continues to operate properly even if
the supply is not always on.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The standard way to do this is to list out the regulators at the top-
level. Adopt the standard way to fix validation.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The standard way to do this is to list out the clocks at the top-level.
Adopt the standard way to fix validation.
Signed-off-by: Thierry Reding <treding@nvidia.com>

battery-name is not a documented property, so drop it to avoid
validation failures.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Use the XUSB controller instead of the legacy EHCI controller to enable
USB 3.0 support.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The new json-schema based validation tools require SD/MMC controller
nodes to be named mmc. Rename all references to them.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The memory node requires a unit-address. For some boards the bootloader,
which is usually locked down, uses a hard-coded name for the memory node
without a unit-address, so we can't fix it on those boards.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The I/O and PLL supplies used for HDMI/DP have alternative names. Use
the names that are given in the hardware documentation for consistency.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The display controller's parent clock depends on the output that's
consuming data from the display controller, so it needs to be specified
as the parent of the corresponding output. The device tree bindings do
specify this, so just correct the existing device trees that get this
wrong.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Interrupt names are used to distinguish between the syncpoint and
general host1x interrupts. Make sure they are available in the DT so
that drivers can use them if necessary.
Signed-off-by: Thierry Reding <treding@nvidia.com>

While the host1x controller found on Tegra132 is the same as on Tegra124
it is good practice to also list a SoC-specific compatible string so any
SoC-specific quirks can be implemented in drivers if necessary.
Signed-off-by: Thierry Reding <treding@nvidia.com>

This interrupt can be used for the operating system to be interrupted
when certain events occur.
Signed-off-by: Thierry Reding <treding@nvidia.com>

On Tegra194, all clients of the memory subsystem can generally address
40 bits of system memory. However, bit 39 has special meaning and will
cause the memory controller to reorder sectors for block-linear buffer
formats. This is primarily useful for graphics-related devices.

Use of bit 39 must be controlled on a case-by-case basis. Buffers that
are used with bit 39 set by one device may be used with bit 39 cleared
by other devices.

Care must be taken to allocate buffers at addresses that do not require
bit 39 to be set. This is normally not an issue for system memory since
there are no Tegra-based systems with enough RAM to exhaust the 39-bit
physical address space. However, when a device is behind an IOMMU, such
as the ARM SMMU on Tegra194, the IOMMUs input address space can cause
IOVA allocations to happen in this region. This is for example the case
when an operating system implements a top-down allocation policy for IO
virtual addresses.

To account for this, describe the path that memory accesses take through
the system. Memory clients will send requests to the memory controller,
which forwards bits [38:0] of the address either to the external memory
controller or the SMMU, depending on the stream ID of the access. A good
way to describe this is using the interconnects bindings, see:

    Documentation/devicetree/bindings/interconnect/interconnect.txt

The standard "dma-mem" path is used to describe the path towards system
memory via the memory controller. A dma-ranges property in the memory
controller's device tree node limits the range of DMA addresses that the
memory clients can use to bits [38:0], ensuring that bit 39 is not used.
Signed-off-by: Thierry Reding <treding@nvidia.com>
---
Changes in v4:
- add additional entries for interconnect-names to match interconnects
- add EMC as destination for interconnect paths

Changes in v3:
- add missing interconnect properties for VIC

Changes in v2:
- use memory client IDs instead of stream IDs (Mikko Perttunen)
Signed-off-by: Thierry Reding <treding@nvidia.com>

The interface used by clients of the memory controller can be configured
in a number of different ways. Describe this path using the interconnect
bindings to enable the configuration of these parameters.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The SDHCI on Tegra210 is in fact not compatible with the one found on
Tegra124. Remove the extra compatible string to reflect that.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The SDHCI on Tegra194 is in fact not compatible with the one found on
Tegra186. Remove the extra compatible string to reflect that.
Signed-off-by: Thierry Reding <treding@nvidia.com>

It is customary to use angle brackets around each tuple in the
interrupts property.
Signed-off-by: Thierry Reding <treding@nvidia.com>

The standard mmio-sram bindings require the #address- and #size-cells
properties to be 1.
Signed-off-by: Thierry Reding <treding@nvidia.com>

PHYs need to have a #phy-cells property that defines how many cells are
required in their specifier. The standard Ethernet PHY doesn't require a
specifier, so set its #phy-cells to 0.
Signed-off-by: Thierry Reding <treding@nvidia.com>

PHYs need to have a #phy-cells property that defines how many cells are
required in their specifier. The standard Ethernet PHY doesn't require
a specifier, so set its #phy-cells to 0.
Signed-off-by: Thierry Reding <treding@nvidia.com>

Pull SafeSetID update from Micah Morton:
 "Add additional LSM hooks for SafeSetID

  SafeSetID is capable of making allow/deny decisions for set*uid calls
  on a system, and we want to add similar functionality for set*gid
  calls.

  The work to do that is not yet complete, so probably won't make it in
  for v5.8, but we are looking to get this simple patch in for v5.8
  since we have it ready.

  We are planning on the rest of the work for extending the SafeSetID
  LSM being merged during the v5.9 merge window"

* tag 'LSM-add-setgid-hook-5.8-author-fix' of git://github.com/micah-morton/linux:
  security: Add LSM hooks to set*gid syscalls