The reset GPIO of WCD9380/WCD9385 is active low and that's how it is
routed on typical boards, so correct the example DTS to use expected
polarity.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20240806114931.40090-3-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The reset GPIO of WCD9340/WCD9341 is active low and that's how it is
routed on typical boards, so correct the example DTS to use expected
polarity.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20240806114931.40090-2-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

The reset GPIO of WCD9370/WCD9375 is active low and that's how it is
routed on typical boards, so correct the example DTS to use expected
polarity.
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20240806114931.40090-1-krzysztof.kozlowski@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Fix the missing mic on OMEN by HP Gaming Laptop 16-n0xxx by adding the
quirk entry with the board ID 8A44.

Cc: stable@vger.kernel.org
Link: https://bugzilla.suse.com/show_bug.cgi?id=1227182Signed-off-by: Takashi Iwai <tiwai@suse.de>
Link: https://patch.msgid.link/20240807170249.16490-1-tiwai@suse.deSigned-off-by: Mark Brown <broonie@kernel.org>

We find that we need to set snd_jack_types to 0. If not,
there will be a probability of button detection errors
Signed-off-by: Zhang Yi <zhangyi@everest-semi.com>
Link: https://patch.msgid.link/20240807025356.24904-2-zhangyi@everest-semi.comSigned-off-by: Mark Brown <broonie@kernel.org>

Lenovo Thinkpad E14 Gen 6 (model type 21M3)
needs a quirk entry for internal mic to work.
Signed-off-by: Krzysztof Stępniak <kfs.szk@gmail.com>
Link: https://patch.msgid.link/20240807001219.1147-1-kfs.szk@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series from Simon Trimmer <simont@opensource.cirrus.com>:

This pair of patches extend wm_adsp to add a callback that can be used
to control whether ALSA controls are added and then tweak cs35l56 to use
it to suppress controls made from firmware coefficients.

Use the late-read buffer in the CS35L56 SoundWire interface to
read OTP memory.

The OTP memory has a longer access latency than chip registers
and cannot guarantee to return the data value in the SoundWire
control response if the bus clock is >4.8 MHz. The Cirrus
SoundWire peripheral IP exposes the bridge-to-bus read buffer
and status bits. For a read from OTP the bridge status bits are
polled to wait for the OTP data to be loaded into the read buffer
and the data is then read from there.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: e1830f66 ("ASoC: cs35l56: Add helper functions for amp calibration")
Link: https://patch.msgid.link/20240805140839.26042-1-rf@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

Recent changes that started checking the codec version broke audio on
the Lenovo ThinkPad X13s:

	wsa_macro 3240000.codec: Unsupported Codec version (0)
	wsa_macro 3240000.codec: probe with driver wsa_macro failed with error -22
	rx_macro 3200000.rxmacro: Unsupported Codec version (0)
	rx_macro 3200000.rxmacro: probe with driver rx_macro failed with error -22

Add the missing codec version to the lookup table so that the codec
drivers probe successfully.

Note that I'm just assuming that this is a 2.0 codec based on the fact
that this device uses the older register layout.

Fixes: 378918d5 ("ASoC: codecs: lpass-macro: add helpers to get codec version")
Fixes: dbacef05 ("ASoC: codec: lpass-rx-macro: prepare driver to accomdate new codec versions")
Fixes: 727de4fb ("ASoC: codecs: lpass-wsa-macro: Correct support for newer v2.5 version")
Signed-off-by: Johan Hovold <johan+linaro@kernel.org>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20240729131351.27886-1-johan+linaro@kernel.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Call efi_rt_services_supported() to check that efi.get_variable exists
before calling it.
Signed-off-by: Richard Fitzgerald <rf@opensource.cirrus.com>
Fixes: 1cad8725 ("ASoC: cs-amp-lib: Add helpers for factory calibration data")
Link: https://patch.msgid.link/20240805114222.15722-1-rf@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

A number of laptops have gone to market with old firmware versions that
export controls that have since been hidden, but we can't just install a
newer firmware because the firmware for each product is customized and
qualified by the OEM. The issue is that alsactl save and restore has no
idea what controls are good to persist which can lead to
misconfiguration.

There is no reason that the UCM or user should need to interact with any
of the ALSA controls for the firmware coefficients so they can be
removed entirely.

Fixes: e4961125 ("ASoC: cs35l56: Add driver for Cirrus Logic CS35L56")
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Link: https://patch.msgid.link/20240805102721.30102-3-simont@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

The callback allows codec drivers to affect how firmware coefficients
are added as controls.

For example a codec driver may selectively add controls by choosing to
call wm_adsp_control_add() based on some filter logic.
Signed-off-by: Simon Trimmer <simont@opensource.cirrus.com>
Link: https://patch.msgid.link/20240805102721.30102-2-simont@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

The microphone/speaker privacy shutter ALSA control handlers need to
call pm_runtime_resume, since the hardware needs to be powered up to
check the hardware state of the shutter. The IRQ handler for the
shutters also needs to notify the ALSA control to inform user-space
the shutters updated. However this leads to a mutex inversion,
between the sdw_dev_lock and the controls_rwsem.

To avoid this mutex inversion cache the kctl pointers before the IRQ
handler, which avoids the need to lookup the control and take the
controls_rwsem.
Suggested-by: Jaroslav Kysela <perex@perex.cz>
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20240802105734.2309788-5-ckeepax@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

No longer any need to hard code the addition of the name prefix, use the
new helper function.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20240802105734.2309788-4-ckeepax@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add new helper functions snd_soc_component_get_kcontrol() and
snd_soc_component_get_kcontrol_locked() that returns a kcontrol
by name, but will factor in the components name_prefix, to handle
situations where multiple components are present with the same
controls.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20240802105734.2309788-3-ckeepax@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20240802105734.2309788-2-ckeepax@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

Default firmware shipped in open source are not licensed for 3P
libraries, therefore topologies should not reference them.

If a OS wants to use 3P (that they have licensed) then they should use
the appropriate topology override mechanisms.

Fixes: 8a7d5d85 ("ASoC: SOF: mediatek: mt8195: Add devicetree support to select topologies")
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Cc: Wojciech Macek <wmacek@google.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patch.msgid.link/20240731212153.921327-1-cujomalainey@chromium.orgSigned-off-by: Mark Brown <broonie@kernel.org>

NAU8822 codec PLL parameters are not an information that the general
user should care about, this print is supposed to be used for debugging,
adjust the debug print priority accordingly.
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Link: https://patch.msgid.link/20240731114828.61238-1-francesco@dolcini.itSigned-off-by: Mark Brown <broonie@kernel.org>

Merge series from Shengjiu Wang <shengjiu.wang@nxp.com>:

There are some register difference for i.MX8 and i.MX9
REG_MICFIL_FIFO_CTRL definition is updated.
REG_MICFIL_FSYNC_CTRL, REG_MICFIL_VERID, REG_MICFIL_PARAM are added from
i.MX9.

Merge series from Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>:

Incorrect mask of Soundwire ports - one bit too long/big - was passed.

Theoretically, too wide mask could cause an out of bounds read in
sdw_get_slave_dpn_prop() in stream.c, however only in the case of buggy
driver, e.g. adding incorrect number of ports via
sdw_stream_add_slave().

Not adding Cc-stable because I don't think the issue can lead to real
out-of-bounds read.

Change to the IN HPF Select kcontrol to the correct name
IN DEC Filter Select.
Signed-off-by: Paul Handrigan <paulha@opensource.cirrus.com>
Link: https://patch.msgid.link/20240726151111.3247774-1-paulha@opensource.cirrus.comSigned-off-by: Mark Brown <broonie@kernel.org>

Add support for the internal microphone for HP 14-em0002la laptop using
a quirk entry.
Signed-off-by: Bruno Ancona <brunoanconasala@gmail.com>
Link: https://patch.msgid.link/20240729045032.223230-1-brunoanconasala@gmail.comSigned-off-by: Mark Brown <broonie@kernel.org>

This patch addresses a regression in the ASoC STI drivers that was
introduced in Linux version 6.6.y. The issue originated from a series of
patches (see https://lore.kernel.org/all/87wmy5b0wt.wl-kuninori.morimoto.gx@renesas.com/)
that unintentionally omitted necessary probe functions for the player
and reader components.

Probe function in `sound/soc/sti/sti_uniperif.c:415` is being replaced
by another probe function located at `sound/soc/sti/sti_uniperif.c:453`,
which should instead be derived from the player and reader components.
This patch correctly reinserts the missing probe entries,
restoring the intended functionality.

Fixes: 9f625f5e ("ASoC: sti: merge DAI call back functions into ops")
Signed-off-by: Jerome Audu <jau@free.fr>
Link: https://patch.msgid.link/20240727-sti-audio-fix-v2-1-208bde546c3f@free.frSigned-off-by: Mark Brown <broonie@kernel.org>

Device has up to WSA884X_MAX_SWR_PORTS number of ports and the array
assigned to prop.sink_dpn_prop has 0..WSA884X_MAX_SWR_PORTS-1 elements.
On the other hand, GENMASK(high, low) creates an inclusive mask between
<high, low>, so we need the mask from 0 up to WSA884X_MAX_SWR_PORTS-1.

Theoretically, too wide mask could cause an out of bounds read in
sdw_get_slave_dpn_prop() in stream.c, however only in the case of buggy
driver, e.g. adding incorrect number of ports via
sdw_stream_add_slave().

Fixes: aa21a7d4 ("ASoC: codecs: wsa884x: Add WSA884x family of speakers")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20240726-asoc-wcd-wsa-swr-ports-genmask-v1-6-d4d7a8b56f05@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Device has up to WSA883X_MAX_SWR_PORTS number of ports and the array
assigned to prop.sink_dpn_prop has 0..WSA883X_MAX_SWR_PORTS-1 elements.
On the other hand, GENMASK(high, low) creates an inclusive mask between
<high, low>, so we need the mask from 0 up to WSA883X_MAX_SWR_PORTS-1.

Theoretically, too wide mask could cause an out of bounds read in
sdw_get_slave_dpn_prop() in stream.c, however only in the case of buggy
driver, e.g. adding incorrect number of ports via
sdw_stream_add_slave().

Fixes: 43b8c7dc ("ASoC: codecs: add wsa883x amplifier support")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20240726-asoc-wcd-wsa-swr-ports-genmask-v1-5-d4d7a8b56f05@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Device has up to WSA881X_MAX_SWR_PORTS number of ports and the array
assigned to prop.sink_dpn_prop has 0..WSA881X_MAX_SWR_PORTS-1 elements.
On the other hand, GENMASK(high, low) creates an inclusive mask between
<high, low>, so we need the mask from 0 up to WSA881X_MAX_SWR_PORTS-1.

Theoretically, too wide mask could cause an out of bounds read in
sdw_get_slave_dpn_prop() in stream.c, however only in the case of buggy
driver, e.g. adding incorrect number of ports via
sdw_stream_add_slave().

Fixes: a0aab9e1 ("ASoC: codecs: add wsa881x amplifier support")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20240726-asoc-wcd-wsa-swr-ports-genmask-v1-4-d4d7a8b56f05@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Device has up to WCD939X_MAX_TX_SWR_PORTS (or WCD939X_MAX_RX_SWR_PORTS
for sink) number of ports and the array assigned to prop.src_dpn_prop
and prop.sink_dpn_prop has 0..WCD939X_MAX_TX_SWR_PORTS-1 elements.  On
the other hand, GENMASK(high, low) creates an inclusive mask between
<high, low>, so we need the mask from 0 up to WCD939X_MAX_TX_SWR_PORTS-1.

Theoretically, too wide mask could cause an out of bounds read in
sdw_get_slave_dpn_prop() in stream.c, however only in the case of buggy
driver, e.g. adding incorrect number of ports via
sdw_stream_add_slave().

Fixes: be2af391 ("ASoC: codecs: Add WCD939x Soundwire devices driver")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20240726-asoc-wcd-wsa-swr-ports-genmask-v1-3-d4d7a8b56f05@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Device has up to WCD938X_MAX_SWR_PORTS number of ports and the array
assigned to prop.src_dpn_prop and prop.sink_dpn_prop has
0..WCD938X_MAX_SWR_PORTS-1 elements.  On the other hand, GENMASK(high,
low) creates an inclusive mask between <high, low>, so we need the mask
from 0 up to WCD938X_MAX_SWR_PORTS-1.

Theoretically, too wide mask could cause an out of bounds read in
sdw_get_slave_dpn_prop() in stream.c, however only in the case of buggy
driver, e.g. adding incorrect number of ports via
sdw_stream_add_slave().

Fixes: 16572522 ("ASoC: codecs: wcd938x-sdw: add SoundWire driver")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20240726-asoc-wcd-wsa-swr-ports-genmask-v1-2-d4d7a8b56f05@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

Device has up to WCD937X_MAX_TX_SWR_PORTS (or WCD937X_MAX_SWR_PORTS
for sink) number of ports and the array assigned to prop.src_dpn_prop
and prop.sink_dpn_prop has 0..WCD937X_MAX_TX_SWR_PORTS-1 elements.  On
the other hand, GENMASK(high, low) creates an inclusive mask between
<high, low>, so we need the mask from 0 up to WCD937X_MAX_TX_SWR_PORTS-1.

Theoretically, too wide mask could cause an out of bounds read in
sdw_get_slave_dpn_prop() in stream.c, however only in the case of buggy
driver, e.g. adding incorrect number of ports via
sdw_stream_add_slave().

Fixes: c99a515f ("ASoC: codecs: wcd937x-sdw: add SoundWire driver")
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://patch.msgid.link/20240726-asoc-wcd-wsa-swr-ports-genmask-v1-1-d4d7a8b56f05@linaro.orgSigned-off-by: Mark Brown <broonie@kernel.org>

On i.MX9x platforms, the REG_MICFIL_FSYNC_CTRL, REG_MICFIL_VERID,
REG_MICFIL_PARAM are added, but they are not existed on i.MX8x
platforms.

Use the existed micfil->soc->use_verid to distinguish the access
permission for these platforms.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://patch.msgid.link/1721897694-6088-3-git-send-email-shengjiu.wang@nxp.comSigned-off-by: Mark Brown <broonie@kernel.org>

On the i.MX9x platforms, the mask of FIFO watermark
is 0x1F, on i.MX8x platforms, the mask of FIFO watermark
is 0X7. So use the mask 0x1F for all platforms to make them
compatible.
Signed-off-by: Shengjiu Wang <shengjiu.wang@nxp.com>
Link: https://patch.msgid.link/1721897694-6088-2-git-send-email-shengjiu.wang@nxp.comSigned-off-by: Mark Brown <broonie@kernel.org>

Merge tag 'kbuild-fixes-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild

Pull Kbuild fixes from Masahiro Yamada:

 - Fix RPM package build error caused by an incorrect locale setup

 - Mark modules.weakdep as ghost in RPM package

 - Fix the odd combination of -S and -c in stack protector scripts,
   which is an error with the latest Clang

* tag 'kbuild-fixes-v6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/masahiroy/linux-kbuild:
  kbuild: Fix '-S -c' in x86 stack protector scripts
  kbuild: rpm-pkg: ghost modules.weakdep file
  kbuild: rpm-pkg: Fix C locale setup

This simplifies the min_t() and max_t() macros by no longer making them
work in the context of a C constant expression.

That means that you can no longer use them for static initializers or
for array sizes in type definitions, but there were only a couple of
such uses, and all of them were converted (famous last words) to use
MIN_T/MAX_T instead.

Cc: David Laight <David.Laight@aculab.com>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Commit 3a7e02c0 ("minmax: avoid overly complicated constant
expressions in VM code") added the simpler MIN_T/MAX_T macros in order
to avoid some excessive expansion from the rather complicated regular
min/max macros.

The complexity of those macros stems from two issues:

 (a) trying to use them in situations that require a C constant
     expression (in static initializers and for array sizes)

 (b) the type sanity checking

and MIN_T/MAX_T avoids both of these issues.

Now, in the whole (long) discussion about all this, it was pointed out
that the whole type sanity checking is entirely unnecessary for
min_t/max_t which get a fixed type that the comparison is done in.

But that still leaves min_t/max_t unnecessarily complicated due to
worries about the C constant expression case.

However, it turns out that there really aren't very many cases that use
min_t/max_t for this, and we can just force-convert those.

This does exactly that.

Which in turn will then allow for much simpler implementations of
min_t()/max_t().  All the usual "macros in all upper case will evaluate
the arguments multiple times" rules apply.

We should do all the same things for the regular min/max() vs MIN/MAX()
cases, but that has the added complexity of various drivers defining
their own local versions of MIN/MAX, so that needs another level of
fixes first.

Link: https://lore.kernel.org/all/b47fad1d0cf8449886ad148f8c013dae@AcuMS.aculab.com/
Cc: David Laight <David.Laight@aculab.com>
Cc: Lorenzo Stoakes <lorenzo.stoakes@oracle.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Merge tag 'ubifs-for-linus-6.11-rc1-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs

Pull UBI and UBIFS updates from Richard Weinberger:

 - Many fixes for power-cut issues by Zhihao Cheng

 - Another ubiblock error path fix

 - ubiblock section mismatch fix

 - Misc fixes all over the place

* tag 'ubifs-for-linus-6.11-rc1-take2' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
  ubi: Fix ubi_init() ubiblock_exit() section mismatch
  ubifs: add check for crypto_shash_tfm_digest
  ubifs: Fix inconsistent inode size when powercut happens during appendant writing
  ubi: block: fix null-pointer-dereference in ubiblock_create()
  ubifs: fix kernel-doc warnings
  ubifs: correct UBIFS_DFS_DIR_LEN macro definition and improve code clarity
  mtd: ubi: Restore missing cleanup on ubi_init() failure path
  ubifs: dbg_orphan_check: Fix missed key type checking
  ubifs: Fix unattached inode when powercut happens in creating
  ubifs: Fix space leak when powercut happens in linking tmpfile
  ubifs: Move ui->data initialization after initializing security
  ubifs: Fix adding orphan entry twice for the same inode
  ubifs: Remove insert_dead_orphan from replaying orphan process
  Revert "ubifs: ubifs_symlink: Fix memleak of inode->i_link in error path"
  ubifs: Don't add xattr inode into orphan area
  ubifs: Fix unattached xattr inode if powercut happens after deleting
  mtd: ubi: avoid expensive do_div() on 32-bit machines
  mtd: ubi: make ubi_class constant
  ubi: eba: properly rollback inside self_check_eba

After a recent change in clang to stop consuming all instances of '-S'
and '-c' [1], the stack protector scripts break due to the kernel's use
of -Werror=unused-command-line-argument to catch cases where flags are
not being properly consumed by the compiler driver:

  $ echo | clang -o - -x c - -S -c -Werror=unused-command-line-argument
  clang: error: argument unused during compilation: '-c' [-Werror,-Wunused-command-line-argument]

This results in CONFIG_STACKPROTECTOR getting disabled because
CONFIG_CC_HAS_SANE_STACKPROTECTOR is no longer set.

'-c' and '-S' both instruct the compiler to stop at different stages of
the pipeline ('-S' after compiling, '-c' after assembling), so having
them present together in the same command makes little sense. In this
case, the test wants to stop before assembling because it is looking at
the textual assembly output of the compiler for either '%fs' or '%gs',
so remove '-c' from the list of arguments to resolve the error.

All versions of GCC continue to work after this change, along with
versions of clang that do or do not contain the change mentioned above.

Cc: stable@vger.kernel.org
Fixes: 4f7fd4d7 ("[PATCH] Add the -fstack-protector option to the CFLAGS")
Fixes: 60a5317f ("x86: implement x86_32 stack protector")
Link: https://github.com/llvm/llvm-project/commit/6461e537815f7fa68cef06842505353cf5600e9c [1]
Signed-off-by: Nathan Chancellor <nathan@kernel.org>
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>

Since ubiblock_exit() is now called from an init function,
the __exit section no longer makes sense.

Cc: Ben Hutchings <bwh@kernel.org>
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202407131403.wZJpd8n2-lkp@intel.com/Signed-off-by: Richard Weinberger <richard@nod.at>
Reviewed-by: Zhihao Cheng <chengzhihao1@huawei.com>

Pull turbostat updates from Len Brown:

 - Enable turbostat extensions to add both perf and PMT (Intel
   Platform Monitoring Technology) counters via the cmdline

 - Demonstrate PMT access with built-in support for Meteor Lake's
   Die C6 counter

* tag 'v6.11-merge' of git://git.kernel.org/pub/scm/linux/kernel/git/lenb/linux:
  tools/power turbostat: version 2024.07.26
  tools/power turbostat: Include umask=%x in perf counter's config
  tools/power turbostat: Document PMT in turbostat.8
  tools/power turbostat: Add MTL's PMT DC6 builtin counter
  tools/power turbostat: Add early support for PMT counters
  tools/power turbostat: Add selftests for added perf counters
  tools/power turbostat: Add selftests for SMI, APERF and MPERF counters
  tools/power turbostat: Move verbose counter messages to level 2
  tools/power turbostat: Move debug prints from stdout to stderr
  tools/power turbostat: Fix typo in turbostat.8
  tools/power turbostat: Add perf added counter example to turbostat.8
  tools/power turbostat: Fix formatting in turbostat.8
  tools/power turbostat: Extend --add option with perf counters
  tools/power turbostat: Group SMI counter with APERF and MPERF
  tools/power turbostat: Add ZERO_ARRAY for zero initializing builtin array
  tools/power turbostat: Replace enum rapl_source and cstate_source with counter_source
  tools/power turbostat: Remove anonymous union from rapl_counter_info_t
  tools/power/turbostat: Switch to new Intel CPU model defines

Pull CXL updates from Dave Jiang:
 "Core:

   - A CXL maturity map has been added to the documentation to detail
     the current state of CXL enabling.

     It provides the status of the current state of various CXL features
     to inform current and future contributors of where things are and
     which areas need contribution.

   - A notifier handler has been added in order for a newly created CXL
     memory region to trigger the abstract distance metrics calculation.

     This should bring parity for CXL memory to the same level vs
     hotplugged DRAM for NUMA abstract distance calculation. The
     abstract distance reflects relative performance used for memory
     tiering handling.

   - An addition for XOR math has been added to address the CXL DPA to
     SPA translation.

     CXL address translation did not support address interleave math
     with XOR prior to this change.

  Fixes:

   - Fix to address race condition in the CXL memory hotplug notifier

   - Add missing MODULE_DESCRIPTION() for CXL modules

   - Fix incorrect vendor debug UUID define

  Misc:

   - A warning has been added to inform users of an unsupported
     configuration when mixing CXL VH and RCH/RCD hierarchies

   - The ENXIO error code has been replaced with EBUSY for inject poison
     limit reached via debugfs and cxl-test support

   - Moving the PCI config read in cxl_dvsec_rr_decode() to avoid
     unnecessary PCI config reads

   - A refactor to a common struct for DRAM and general media CXL
     events"

* tag 'cxl-for-6.11' of git://git.kernel.org/pub/scm/linux/kernel/git/cxl/cxl:
  cxl/core/pci: Move reading of control register to immediately before usage
  cxl: Remove defunct code calculating host bridge target positions
  cxl/region: Verify target positions using the ordered target list
  cxl: Restore XOR'd position bits during address translation
  cxl/core: Fold cxl_trace_hpa() into cxl_dpa_to_hpa()
  cxl/test: Replace ENXIO with EBUSY for inject poison limit reached
  cxl/memdev: Replace ENXIO with EBUSY for inject poison limit reached
  cxl/acpi: Warn on mixed CXL VH and RCH/RCD Hierarchy
  cxl/core: Fix incorrect vendor debug UUID define
  Documentation: CXL Maturity Map
  cxl/region: Simplify cxl_region_nid()
  cxl/region: Support to calculate memory tier abstract distance
  cxl/region: Fix a race condition in memory hotplug notifier
  cxl: add missing MODULE_DESCRIPTION() macros
  cxl/events: Use a common struct for DRAM and General Media events