- 25 Jan, 2015 24 commits
-
-
Yishai Hadas authored
Maintain a persistent memory that should survive reset flow/PCI error. This comes as a preparation for coming series to support above flows. Signed-off-by:
Yishai Hadas <yishaih@mellanox.com> Signed-off-by:
Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Andy Shevchenko authored
Call hex2bin() library function instead of doing conversion here. Signed-off-by:
Andy Shevchenko <andy.shevchenko@gmail.com> Signed-off-by:
-
Andy Shevchenko authored
Call hex2bin() library function, instead of doing conversion here. Signed-off-by:
Oliver Neukum <oneukum@suse.de> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-nextDavid S. Miller authored
Jeff Kirsher says: ==================== Intel Wired LAN Driver Updates 2015-01-22 This series contains updates to e1000, e1000e, igb, fm10k and virtio_net. Asaf Vertz provides a fix for e1000 to future-proof the time comparisons by using time_after_eq() instead of plain math. Mathias Koehrer provides a fix for e1000e to add a check to e1000_xmit_frame() to ensure a work queue will not be scheduled that has not been initialized. Jacob adds the use of software timestamping via the virtio_net driver. Alex Duyck cleans up page reuse code in igb and fm10k. Cleans up the page reuse code from getting into a state where all the workarounds needed are in place as well as cleaning up oversights, such as using __free_pages instead of put_page to drop a locally allocated page. Richard Cochran provides 4 patches for igb dealing with time sync. First provides a helper function since the code that handles the time sync interrupt is repeated in three different places. Then serializes the access to the time sync interrupt since the registers may be manipulated from different contexts. Enables the use of i210 device interrupt to generate an internal PPS event for adjusting the kernel system time. The i210 device offers a number of special PTP hardware clock features on the Software Defined Pins (SDPs), so added support for two of the possible functions (time stamping external events and periodic output signals). Or Gerlitz fixes fm10k from double setting of NETIF_F_SG since the networking core does it for the driver during registration time. Joe Stringer adds support for up to 104 bytes of inner+outer headers in fm10k and adds an initial check to fail encapsulation offload if these are too large. Matthew increases the timeout for the data path reset based on feedback from the hardware team, since 100us is too short of a time to wait for the data path reset to complete. Alexander Graf provides a fix for igb to indicate failure on VF reset for an empty MAC address, to mirror the behavior of ixgbe. Florian Westphal updates e1000 and e1000e to support txtd update delay via xmit_more, this way we won't update the Tx tail descriptor if the queue has not been stopped and we know at least one more skb will be sent right away. ==================== Signed-off-by: -
David S. Miller authored
Tom Herbert says: ==================== vxlan: Don't use UDP socket for transmit UDP socket is not pertinent to transmit for UDP tunnels, checksum enablement can be done without a socket. This patch set eliminates reference to a socket in udp_tunnel_xmit functions and in VXLAN transmit. Also, make GBP, RCO, can CSUM6_RX flags visible to receive socket and only match these for shareable socket. v2: Fix geneve to call udp_tunnel_xmit with good arguments. ==================== Signed-off-by: -
Tom Herbert authored
In the vxlan transmit path there is no need to reference the socket for a tunnel which is needed for the receive side. We do, however, need the vxlan_dev flags. This patch eliminate references to the socket in the transmit path, and changes VXLAN_F_UNSHAREABLE to be VXLAN_F_RCV_FLAGS. This mask is used to store the flags applicable to receive (GBP, CSUM6_RX, and REMCSUM_RX) in the vxlan_sock flags. Signed-off-by:
Tom Herbert <therbert@google.com> Signed-off-by:
-
Tom Herbert authored
The UDP tunnel transmit functions udp_tunnel_xmit_skb and udp_tunnel6_xmit_skb include a socket argument. The socket being passed to the functions (from VXLAN) is a UDP created for receive side. The only thing that the socket is used for in the transmit functions is to get the setting for checksum (enabled or zero). This patch removes the argument and and adds a nocheck argument for checksum setting. This eliminates the unnecessary dependency on a UDP socket for UDP tunnel transmit. Signed-off-by:
-
Nimrod Andy authored
Enable kernel config "CONFIG_HAVE_DMA_API_DEBUG", FEC have kernel warning: [ 6.650444] fec 2188000.ethernet: DMA-API: device driver tries to free DMA memory it has not allocated [ 6.664289] Modules linked in: [ 6.667378] CPU: 0 PID: 3 Comm: ksoftirqd/0 Not tainted 3.19.0-rc4-00688-g88340160-dirty #150 [ 6.675841] Hardware name: Freescale i.MX6 SoloX (Device Tree) [ 6.681698] Backtrace: [ 6.684189] [<80011e3c>] (dump_backtrace) from [<80011fdc>] (show_stack+0x18/0x1c) [ 6.691789] r6:80890154 r5:00000000 r4:00000000 r3:00000000 [ 6.697533] [<80011fc4>] (show_stack) from [<806d2d88>] (dump_stack+0x80/0x9c) [ 6.704799] [<806d2d08>] (dump_stack) from [<8002a4e4>] (warn_slowpath_common+0x7c/0xb4) [ 6.712917] r5:00000445 r4:00000000 [ 6.716544] [<8002a468>] (warn_slowpath_common) from [<8002a5c0>] (warn_slowpath_fmt+0x38/0x40) [ 6.725265] r8:809a2ee8 r7:00000000 r6:00000000 r5:00000000 r4:00000042 [ 6.732087] [<8002a58c>] (warn_slowpath_fmt) from [<802d6268>] (check_unmap+0x86c/0x98c) [ 6.740202] r3:808c79bc r2:8089060c [ 6.743826] [<802d59fc>] (check_unmap) from [<802d65e4>] (debug_dma_unmap_page+0x80/0x88) [ 6.752029] r10:00000000 r9:00000000 r8:00000000 r7:00000001 r6:be12a410 r5:00000000 [ 6.759967] r4:00000042 [ 6.762538] [<802d6564>] (debug_dma_unmap_page) from [<80440248>] (fec_enet_rx_napi+0x7ec/0xb9c) [ 6.771345] r7:00000400 r6:be3e4000 r5:bf08fa20 r4:be036000 [ 6.777094] [<8043fa5c>] (fec_enet_rx_napi) from [<8056ae24>] (net_rx_action+0x134/0x324) [ 6.785297] r10:be089e60 r9:80998180 r8:ffff8d68 r7:0000012c r6:00000040 r5:00000001 [ 6.793239] r4:be036718 [ 6.795801] [<8056acf0>] (net_rx_action) from [<8002db24>] (__do_softirq+0x138/0x2d0) [ 6.803655] r10:00000003 r9:00000003 r8:80996378 r7:8099c080 r6:00000100 r5:8099c08c [ 6.811593] r4:00000000 [ 6.814157] [<8002d9ec>] (__do_softirq) from [<8002dd00>] (run_ksoftirqd+0x44/0x5c) [ 6.821836] r10:00000000 r9:00000000 r8:809b133c r7:00000000 r6:00000001 r5:00000000 [ 6.829775] r4:be027e80 [ 6.832346] [<8002dcbc>] (run_ksoftirqd) from [<80048290>] (smpboot_thread_fn+0x154/0x1c4) [ 6.840649] [<8004813c>] (smpboot_thread_fn) from [<80044780>] (kthread+0xdc/0xf8) [ 6.848224] r10:00000000 r8:00000000 r7:8004813c r6:be027e80 r5:be027ec0 r4:00000000 [ 6.856179] [<800446a4>] (kthread) from [<8000ebc8>] (ret_from_fork+0x14/0x2c) [ 6.863425] r7:00000000 r6:00000000 r5:800446a4 r4:be027ec0 [ 6.869156] ---[ end trace 861cf914d2461a8b ]--- There have one bug in .fec_enet_tx_queue() function to unmap the DMA memory: For SG or TSO, get one buffer descriptor and then unmap the related DMA memory, and then get the next buffer descriptor, loop to while() to check "TX_READY". If "TX_READY" bit still __IS__ existed in the BD (The next fraglist or next TSO packet is not transmited complitely), exit the current clean work. When the next work is triggered, it still repeat above step with the same BD. The potential issue is that unmap the same DMA memory for multiple times. The patch fix the clean work for SG and TSO packet. Reported-by:
Anand Moon <moon.linux@yahoo.com> Reported-by:
Christian Gmeiner <christian.gmeiner@gmail.com> Signed-off-by:
Fugang Duan <B38611@freescale.com> Signed-off-by:
-
David S. Miller authored
Sathya Perla says: ==================== be2net: patch set Hi David, as the below patch-set includes minor bug fixes and some code re-org, pls consider applying it to the "net-next" tree. Thanks! Patch 1 fixes a bit of code duplication involving interface object creation code. Patch 2 ensures that when a flow-control FW cmd fails, the adapter state continues to reflect the old values. This allows for correct reporting on subsequent ethtool "get". Patch 3 returns proper error for link config change on BE3/Lancer Patch 4 adds a kernel log message for FW boot error on Lancer Patch 5 adds a function reset on Lancer as a part of the function init sequence. Patch 6 moves some FW-cmd definitions that belong in be_cmds.h, but were placed in be_hw.h Patch 7 resets the "bw_min" field while configuring "bw_max" needed for TX rate limiting config. ==================== Signed-off-by: -
Kalesh AP authored
When max_tx_rate is set via bw_max in the NIC resource desc, bw_min must be set to 0. Signed-off-by:
Kalesh AP <kalesh.purayil@emulex.com> Signed-off-by:
Sathya Perla <sathya.perla@emulex.com> Signed-off-by:
-
Vasundhara Volam authored
Some FW cmd related definitions were included in be_hw.h Signed-off-by:
Vasundhara Volam <vasundhara.volam@emulex.com> Signed-off-by:
-
Kalesh AP authored
The Lancer FW is picky about requiring a function reset FW cmd as a part of the initialization sequence. Signed-off-by:
-
Kalesh AP authored
This patch adds a log message in case of POST timeout in Lancer to help debugging failure cases. It also logs sliport_status register value in case of POST timeout. Signed-off-by:
-
Kalesh AP authored
The support for this exists only in skyhawk FW. Signed-off-by:
-
Kalesh AP authored
When the FW cmd to set flow control fails, the adapter state must simply reflect the old values. Signed-off-by:
-
Kalesh AP authored
This removes a bit of duplication of code that initializes the en_flags. Signed-off-by:
-
David S. Miller authored
Romain Perier says: ==================== net: stmmac: dwmac-rk: Fix phy regulator issues This series fixes few issues in dwmac-rk: 1. Voltage settings was hardcoded into the driver for the phy regulator. The driver now uses the default voltage settings found in the devicetree, which are applied throught the regulator framework. 2. The regulator name used to power on or power off the phy was put in the devicetree variable "phy_regulator", which is not standard and added a lot of code for nothing. The driver now uses the devicetree property "phy-supply" and the corresponding functions to manipulate this regulator. The corresponding devicetree files are also updated. As this new binding for rk3288 has not been released with any official kernel yet (not until 3.20), I don't need to care about keeping compatibility with the old non standard property. ==================== Tested-by:
Heiko Stuebner <heiko@sntech.de> Reviewed-by:
-
Romain Perier authored
As no property for phy regulator was documented in this dt-binding documentation, this commit adds an entry for the optional property phy-supply. Signed-off-by:
Romain Perier <romain.perier@gmail.com> Signed-off-by:
-
Romain Perier authored
Currently, dwmac-rk uses a custom propety "phy_regulator" to get the name of the right regulator to use to power on or power off the phy. This commit converts the driver to use phy-supply devicetree property and the corresponding API, it cleans the code a bit and make it simpler to maintain. This also replaces the property phy_regulator by the standard property phy-supply in rk3288-evb-rk808.dts. Signed-off-by:
-
Romain Perier authored
Signed-off-by:
-
Romain Perier authored
As these settings can be directly expressed from devicetree for both fixed regulators and pmic-integrated regulators, it is more standard to set them from dts and let the regulator framework use the right voltage informations when it is used in the driver. Signed-off-by:
-
David S. Miller authored
Hariprasad Shenai says: ==================== cxgb4: Add support to dump flash and rss config This patch series adds support to dump flash, rss, rss_key, rss_config, rss_pf_config and rss_vf_config debugfs entries. The patches series is created against 'net-next' tree. And includes patches on cxgb4 driver. We have included all the maintainers of respective drivers. Kindly review the change and let us know in case of any review comments. ==================== Signed-off-by: -
Hariprasad Shenai authored
Adds support to dump the rss table, rss_config, rss_key, rss_pf_config and rss_vf_config Signed-off-by:
Hariprasad Shenai <hariprasad@chelsio.com> Signed-off-by:
-
Hariprasad Shenai authored
Adds support to dump the contents of the flash in the adapter Signed-off-by:
-
- 24 Jan, 2015 9 commits
-
-
David Vrabel authored
Always fully coalesce guest Rx packets into the minimum number of ring slots. Reducing the number of slots per packet has significant performance benefits when receiving off-host traffic. Results from XenServer's performance benchmarks: Baseline Full coalesce Interhost VM receive 7.2 Gb/s 11 Gb/s Interhost aggregate 24 Gb/s 24 Gb/s Intrahost single stream 14 Gb/s 14 Gb/s Intrahost aggregate 34 Gb/s 34 Gb/s However, this can increase the number of grant ops per packet which decreases performance of backend (dom0) to VM traffic (by ~10%) /unless/ grant copy has been optimized for adjacent ops with the same source or destination (see "grant-table: defer releasing pages acquired in a grant copy"[1] expected in Xen 4.6). [1] http://lists.xen.org/archives/html/xen-devel/2015-01/msg01118.htmlSigned-off-by:David Vrabel <david.vrabel@citrix.com> Acked-by:
Ian Campbell <ian.campbell@citrix.com> Signed-off-by:
-
David S. Miller authored
Nicolas Dichtel says: ==================== netns: advertise netns via netlink The first patch of the series fix a bug of the previous series (present in net-next only). The rest of the series adds an attribute to advertise the peer netns for rtnetlink messages where this information is needed by userland to be able to interpret fully the received message. ==================== Signed-off-by: -
Nicolas Dichtel authored
Netlink FDB messages are sent in the link netns. The header of these messages contains the ifindex (ndm_ifindex) of the netdevice, but this ifindex is unusable in case of x-netns vxlan. I named the new attribute NDA_NDM_IFINDEX_NETNSID, to avoid confusion with NDA_IFINDEX. Signed-off-by:
Nicolas Dichtel <nicolas.dichtel@6wind.com> Signed-off-by:
-
Nicolas Dichtel authored
Assign rtnl_link_ops->get_link_net() callback so that IFLA_LINK_NETNSID is added to rtnetlink messages. Signed-off-by:
-
Nicolas Dichtel authored
Assign rtnl_link_ops->get_link_net() callback so that IFLA_LINK_NETNSID is added to rtnetlink messages. Signed-off-by:
-
Nicolas Dichtel authored
Assign rtnl_link_ops->get_link_net() callback so that IFLA_LINK_NETNSID is added to rtnetlink messages. Signed-off-by:
-
Nicolas Dichtel authored
Assign rtnl_link_ops->get_link_net() callback so that IFLA_LINK_NETNSID is added to rtnetlink messages. Signed-off-by:
-
Nicolas Dichtel authored
If an error occurs when the netdevice is moved to the link netns, a full cleanup must be done. Fixes: 317f4810 ("rtnl: allow to create device with IFLA_LINK_NETNSID set") Signed-off-by:
-
Thomas Graf authored
Depending on NETFILTER is not sufficient to ensure the presence of the 'mark' field in nf_conn, also needs to depend on NF_CONNTRACK_MARK. Fixes: 22a5dc ("net: sched: Introduce connmark action") Cc: Felix Fietkau <nbd@openwrt.org> Cc: Jamal Hadi Salim <jhs@mojatatu.com> Signed-off-by:Thomas Graf <tgraf@suug.ch> Signed-off-by:
-
- 23 Jan, 2015 7 commits
-
-
Florian Westphal authored
Don't update Tx tail descriptor if queue hasn't been stopped and we know at least one more skb will be sent right away. Signed-off-by:
Florian Westphal <fw@strlen.de> Tested-by:
Aaron Brown <aaron.f.brown@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Florian Westphal authored
Don't update Tx tail descriptor if we queue hasn't been stopped and we know at least one more skb will be sent right away. Signed-off-by:
-
Alexander Graf authored
Commit 5ac6f91d changed the igb driver to expose a zero (empty) mac address to the VF on reset rather than a random one. However, that behavioral change also requires igbvf driver changes which can be hard especially when we want to talk to proprietary guest OSs. Looking at the code previous to the commit in Linux that made igbvf work with empty mac addresses (8d56b6d5), we can see that on reset failure the driver will try to generate a new mac address with both the old and the new code. Furthermore, ixgbe does send reset failure when it detects an empty mac address (35055928). So I think it's safe to make igb behave the same. With this patch I can successfully run a Windows 8.1 guest with an empty mac address and an assigned igbvf device that has no mac address set by the host. If anyone is aware of a guest driver that chokes on NACK returns of VF RESET commands, please speak up. Signed-off-by:
Alexander Graf <agraf@suse.de> Tested-by:
-
Matthew Vick authored
Based on feedback from the hardware team, 100us is too short of a time to wait for the data path reset to complete and the recommendation is to increase this timeout to 150us. Signed-off-by:
Matthew Vick <matthew.vick@intel.com> Tested-by:
Krishneil Singh <Krishneil.k.singh@intel.com> Signed-off-by:
-
Joe Stringer authored
fm10k supports up to 184 bytes of inner+outer headers. Add an initial check to fail encap offload if these are too large. Signed-off-by:
Joe Stringer <joestringer@nicira.com> Tested-by:
-
Or Gerlitz authored
The networking core does it for the driver during registration time. Signed-off-by:
-
Richard Cochran authored
The i210 device offers a number of special PTP Hardware Clock features on the Software Defined Pins (SDPs). This patch adds support for two of the possible functions, namely time stamping external events, and periodic output signals. The assignment of PHC functions to the four SDP can be freely chosen by the user. Signed-off-by:
Richard Cochran <richardcochran@gmail.com> Tested-by:
-
