Before calling on any of the platform hooks, shared transport driver checks
for the validity of the platform hooks as to whether it is provided or not.
A wrong function was being checked for, before the chip_awake hook was called
by the HCI-LL sleep logic handler. This patch corrects the check.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Matthias Kaehlcke <matthias@kaehlcke.net>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If the read firmware version response from the chip is split into multiple
frames of UART buffer being received by the host, the TI-ST driver as of today
is unable to put the pieces of response together unlike other responses.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Be nice to CPU and don't hog the resources, use a nice wait_for_interruptible
timeout for completions instead of wait_for_timeout which is
non-interruptible.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

If the communication with the WiLink breaks down for whatever reasons & the
ti-st driver is unable to un-install the line-discipline during clean-up in
st_kim_stop, the GPIO should be held low (BT_EN=0) & the platform's chip
disable hook shall also be called.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

remove sparse warnings by assigning right storage specifiers to functions and
also clean-up the declarations in the include/linux/ti_wilink_st.h
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

A platform hook to enable/disable the chip was introduced to perform specific
activities to power-up and power-down the WL chip.
Moving the power-up/down sequence also there makes more sense, since different
platforms have begun to have their own ways to power-up/down the chip.
This patch removes all of the gpio handling done by the driver in
st_kim_start/st_kim_stop & any of the gpio request done in the probe function.
Signed-off-by: Pavan Savoy <pavan_savoy@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

There is an automatic binding done for I2C devices in the of_i2c core
code. So, DT will be able to bind to any I2C device using the
already existing table: MODULE_DEVICE_TABLE(i2c, bmp085_id).

Tested on omap5430 evm.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Cc: Benoit Cousson <b-cousson@ti.com>
Cc: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

These drivers set the DMA_INTERRUPT capability bit when requesting a DMA
controller channel. This was historical, and is no longer needed.

Recent changes to the drivers/dma/fsldma.c driver have removed support
for this flag. This makes the carma drivers unable to find a DMA channel
with the required capabilities.

Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Ira W. Snyder <iws@ovro.caltech.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

this driver's pch_phub_pci_init, and pch_phub_pci_exit functions with
the module_init and module_exit calls can be replaced with
module_pci_driver
Signed-off-by: Devendra Naga <develkernel412222@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

sparse warns about using 0 as NULL pointer,

drivers/misc/pch_phub.c:702:44: warning: Using plain integer as NULL pointer
Signed-off-by: Devendra Naga <develkernel412222@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Convert a 0 error return code to a negative one, as returned elsewhere in the
function.

A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)

// <smpl>
@@
identifier ret;
expression e,e1,e2,e3,e4,x;
@@

(
if (\(ret != 0\|ret < 0\) || ...) { ... return ...; }
|
ret = 0
)
... when != ret = e1
*x = \(kmalloc\|kzalloc\|kcalloc\|devm_kzalloc\|ioremap\|ioremap_nocache\|devm_ioremap\|devm_ioremap_nocache\)(...);
... when != x = e2
    when != ret = e3
*if (x == NULL || ...)
{
  ... when != ret = e4
*  return ret;
}
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Acked-by: Mark Gross <mark.gross@intel.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

In the process of porting boards to devicetree implemenation, we should
keep information about external circuitry where they belong - the
individual drivers.

This patch adds a way to specify a GPIO to drive the (optional) external
pull-up logic, rather than using a function pointer for that.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Acked-by: Ville Syrjälä <syrjala@sci.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

This patch add DT bindings to the w1-gpio driver, along with some
documentation on how to use them.
Signed-off-by: Daniel Mack <zonque@gmail.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Acked-by: Ville Syrjälä <syrjala@sci.fi>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Let the driver compile everywhere while
also removing unnecessary headers.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

trivial patch, no functional changes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

this lets us remove a bit of boilerplate code.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

trivial patch, no functional changes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

we have the helpful resource_size() macro to
calculate the size of the memory resource for
us, let's use it.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

trivial patch, no functional changes.
Signed-off-by: Felipe Balbi <balbi@ti.com>
Acked-by: Evgeniy Polyakov <zbr@ioremap.net>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

use watchdog_set/get_drvdata for passing mei_device
to watchdog_ops handlers instead of using global mei_device
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Before ME watchdog was exported through standard watchdog interface
it was closed and started together with the mei device.

The major issue is that closing ME watchdog disabled also MEI device,
to fix this the watchdog state machine has to be independent from MEI
state machine.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

1. rename defines to more be descriptive
2. remove duplicated defines from interface.h
3. add common prefix MEI_
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

According watchdog-kernel-api.txt WDIOF_SETTIMEOUT
should be set if the driver supplies set_timeout function
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

After watchdog was disabled the driver would stall
due to wrong calculation of credits reduction

The cat&paste bug was introduced in the commit
7bdf72d3
mei: introduce mei_data2slots wrapper
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

1. add MEI_DEV_ prefix for mei device state enums
2. rename mei_state to dev_state
3. add constant to string translation for debug purposes
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

1. reformat PCI ids list in hw.h for better readability
2. update some code and brand names
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

The main purpose of this function is to exclude ME devices
without support for MEI/HECI interface from binding

Currently affected systems are C600/X79 based servers
that expose PCI device even though it doesn't supported ME Interface.
MEI driver accessing such nonfunctional device can corrupt
the system.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

me client search functions returns index
into me_client array according me client id
or me client uuid.

1. Add common prefix for the functions mei_me_cl_<>
2. create new function mei_me_cl_by_id that wraps open
 coded loops scattered over the code
3. rename mei_find_me_client_index to  mei_me_cl_by_uuid
4. rename mei_find_me_client_update_filext  to
 mei_me_cl_update_filext and updates its parameter names
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

Pull OLPC platform updates from Andres Salomon:
 "These move the OLPC Embedded Controller driver out of
  arch/x86/platform and into drivers/platform/olpc.

  OLPC machines are now ARM-based (which means lots of x86 and ARM
  changes), but are typically pretty self-contained..  so it makes more
  sense to go through a separate OLPC tree after getting the appropriate
  review/ACKs."

* 'for-linus-3.6' of git://dev.laptop.org/users/dilinger/linux-olpc:
  x86: OLPC: move s/r-related EC cmds to EC driver
  Platform: OLPC: move global variables into priv struct
  Platform: OLPC: move debugfs support from x86 EC driver
  x86: OLPC: switch over to using new EC driver on x86
  Platform: OLPC: add a suspended flag to the EC driver
  Platform: OLPC: turn EC driver into a platform_driver
  Platform: OLPC: allow EC cmd to be overridden, and create a workqueue to call it
  drivers: OLPC: update various drivers to include olpc-ec.h
  Platform: OLPC: add a stub to drivers/platform/ for the OLPC EC driver

Pull arm-soc Marvell Orion device-tree updates from Olof Johansson:
 "This contains a set of device-tree conversions for Marvell Orion
  platforms that were staged early but took a few tries to get the
  branch into a format where it was suitable for us to pick up.

  Given that most people working on these platforms are hobbyists with
  limited time, we were a bit more flexible with merging it even though
  it came in late."

* tag 'dt2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (21 commits)
  ARM: Kirkwood: Replace mrvl with marvell
  ARM: Kirkwood: Describe GoFlex Net LEDs and SATA in DT.
  ARM: Kirkwood: Describe Dreamplug LEDs in DT.
  ARM: Kirkwood: Describe iConnects LEDs in DT.
  ARM: Kirkwood: Describe iConnects temperature sensor in DT.
  ARM: Kirkwood: Describe IB62x0 LEDs in DT.
  ARM: Kirkwood: Describe IB62x0 gpio-keys in DT.
  ARM: Kirkwood: Describe DNS32? gpio-keys in DT.
  ARM: Kirkwood: Move common portions into a kirkwood-dnskw.dtsi
  ARM: Kirkwood: Replace DNS-320/DNS-325 leds with dt bindings
  ARM: Kirkwood: Describe DNS325 temperature sensor in DT.
  ARM: Kirkwood: Use DT to configure SATA device.
  ARM: kirkwood: use devicetree for SPI on dreamplug
  ARM: kirkwood: Add LS-XHL and LS-CHLv2 support
  ARM: Kirkwood: Initial DTS support for Kirkwood GoFlex Net
  ARM: Kirkwood: Add basic device tree support for QNAP TS219.
  ATA: sata_mv: Add device tree support
  ARM: Orion: DTify the watchdog timer.
  ARM: Orion: Add arch support needed for I2C via DT.
  ARM: kirkwood: use devicetree for orion-spi
  ...

Conflicts:
	drivers/watchdog/orion_wdt.c

Pull arm-soc cpuidle enablement for OMAP from Olof Johansson:
 "Coupled cpuidle was meant to merge for 3.5 through Len Brown's tree,
  but didn't go in because the pull request ended up rejected.  So it
  just got merged, and we got this staged branch that enables the
  coupled cpuidle code on OMAP.

  With a stable git workflow from the other maintainer we could have
  staged this earlier, but that wasn't the case so we have had to merge
  it late.

  The alternative is to hold it off until 3.7 but given that the code is
  well-isolated to OMAP and they are eager to see it go in, I didn't
  push back hard in that direction."

* tag 'pm2' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: OMAP4: CPUidle: Open broadcast clock-event device.
  ARM: OMAP4: CPUidle: add synchronization for coupled idle states
  ARM: OMAP4: CPUidle: Use coupled cpuidle states to implement SMP cpuidle.
  ARM: OMAP: timer: allow gp timer clock-event to be used on both cpus

Pull ARM SoC fixes from Olof Johansson:
 "A few fixes for merge window fallout, and a bugfix for timer resume on
  PRIMA2."

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: mmp: add missing irqs.h
  arm: mvebu: fix typo in .dtsi comment for Armada XP SoCs
  ARM: PRIMA2: delete redundant codes to restore LATCHED when timer resumes
  ARM: mxc: Include missing irqs.h header

Pull SuperH fixes from Paul Mundt.

* tag 'sh-for-linus' of git://github.com/pmundt/linux-sh: (24 commits)
  sh: explicitly include sh_dma.h in setup-sh7722.c
  sh: ecovec: care CN5 VBUS if USB host mode
  sh: sh7724: fixup renesas_usbhs clock settings
  sh: intc: initial irqdomain support.
  sh: pfc: Fix up init ordering mess.
  serial: sh-sci: fix compilation breakage, when DMA is enabled
  dmaengine: shdma: restore partial transfer calculation
  sh: modify the sh_dmae_slave_config for RSPI in setup-sh7757
  sh: Fix up recursive fault in oops with unset TTB.
  sh: pfc: Build fix for pinctrl_remove_gpio_range() changes.
  sh: select the fixed regulator driver on several boards
  sh: ecovec: switch MMC power control to regulators
  sh: add fixed voltage regulators to se7724
  sh: add fixed voltage regulators to sdk7786
  sh: add fixed voltage regulators to rsk
  sh: add fixed voltage regulators to migor
  sh: add fixed voltage regulators to kfr2r09
  sh: add fixed voltage regulators to ap325rxa
  sh: add fixed voltage regulators to sh7757lcr
  sh: add fixed voltage regulators to sh2007
  ...

Pull additional md update from NeilBrown:
 "This contains a few patches that depend on plugging changes in the
  block layer so needed to wait for those.

  It also contains a Kconfig fix for the new RAID10 support in dm-raid."

* tag 'md-3.6' of git://neil.brown.name/md:
  md/dm-raid: DM_RAID should select MD_RAID10
  md/raid1: submit IO from originating thread instead of md thread.
  raid5: raid5d handle stripe in batch way
  raid5: make_request use batch stripe release

Pull two ceph fixes from Sage Weil:
 "The first patch fixes up the old crufty open intent code to use the
  atomic_open stuff properly, and the second fixes a possible null deref
  and memory leak with the crypto keys."

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/sage/ceph-client:
  libceph: fix crypto key null deref, memory leak
  ceph: simplify+fix atomic_open

Merge tag 'ecryptfs-3.6-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs

Pull ecryptfs fixes from Tyler Hicks:
 - Fixes a bug when the lower filesystem mount options include 'acl',
   but the eCryptfs mount options do not
 - Cleanups in the messaging code
 - Better handling of empty files in the lower filesystem to improve
   usability.  Failed file creations are now cleaned up and empty lower
   files are converted into eCryptfs during open().
 - The write-through cache changes are being reverted due to bugs that
   are not easy to fix.  Stability outweighs the performance
   enhancements here.
 - Improvement to the mount code to catch unsupported ciphers specified
   in the mount options

* tag 'ecryptfs-3.6-rc1-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tyhicks/ecryptfs:
  eCryptfs: check for eCryptfs cipher support at mount
  eCryptfs: Revert to a writethrough cache model
  eCryptfs: Initialize empty lower files when opening them
  eCryptfs: Unlink lower inode when ecryptfs_create() fails
  eCryptfs: Make all miscdev functions use daemon ptr in file private_data
  eCryptfs: Remove unused messaging declarations and function
  eCryptfs: Copy up POSIX ACL and read-only flags from lower mount

Pull CIFS update from Steve French:
 "Adds SMB2 rmdir/mkdir capability to the SMB2/SMB2.1 support in cifs.

  I am holding up a few more days on merging the remainder of the
  SMB2/SMB2.1 enablement although it is nearing review completion, in
  order to address some review comments from Jeff Layton on a few of the
  subsequent SMB2 patches, and also to debug an unrelated cifs problem
  that Pavel discovered."

* 'for-next' of git://git.samba.org/sfrench/cifs-2.6:
  CIFS: Add SMB2 support for rmdir
  CIFS: Move rmdir code to ops struct
  CIFS: Add SMB2 support for mkdir operation
  CIFS: Separate protocol specific part from mkdir
  CIFS: Simplify cifs_mkdir call

Borislav Petkov reports that the new warning added in commit
88fdf75d ("mm: warn if pg_data_t isn't initialized with zero")
triggers for him, and it is the node_start_pfn field that has already
been initialized once.

The call trace looks like this:

  x86_64_start_kernel ->
    x86_64_start_reservations ->
    start_kernel ->
    setup_arch ->
    paging_init ->
    zone_sizes_init ->
    free_area_init_nodes ->
    free_area_init_node

and (with the warning replaced by debug output), Borislav sees

  On node 0 totalpages: 4193848
    DMA zone: 64 pages used for memmap
    DMA zone: 6 pages reserved
    DMA zone: 3890 pages, LIFO batch:0
    DMA32 zone: 16320 pages used for memmap
    DMA32 zone: 798464 pages, LIFO batch:31
    Normal zone: 52736 pages used for memmap
    Normal zone: 3322368 pages, LIFO batch:31
  free_area_init_node: pgdat->node_start_pfn: 4423680      <----
  On node 1 totalpages: 4194304
    Normal zone: 65536 pages used for memmap
    Normal zone: 4128768 pages, LIFO batch:31
  free_area_init_node: pgdat->node_start_pfn: 8617984      <----
  On node 2 totalpages: 4194304
    Normal zone: 65536 pages used for memmap
    Normal zone: 4128768 pages, LIFO batch:31
  free_area_init_node: pgdat->node_start_pfn: 12812288     <----
  On node 3 totalpages: 4194304
    Normal zone: 65536 pages used for memmap
    Normal zone: 4128768 pages, LIFO batch:31

so remove the bogus warning for now to avoid annoying people.  Minchan
Kim is looking at it.
Reported-by: Borislav Petkov <bp@amd64.org>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>