Since passing the clock is not mandatory, change the warning message to debug,
so that we avoid getting the following clock failure message on every boot:

smsc911x: Driver version 2008-10-21
smsc911x smsc911x (unregistered net_device): couldn't get clock -2
libphy: smsc911x-mdio: probed
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Daniel Baluta <dbaluta@ixiacom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates

This series contains updates to e100, igb, igbvf, ixgbe and ixgbevf.

Stefan adds a igb patch to enable the ability strip VLAN header information
for packets bound for a VM on i350 hardware.

Joe Perches provides patches for e100, igb, igbvf, ixgbe and ixgbevf to
convert the use of __constant_<foo> to just <foo> to align with the rest
of the kernel.

Don provides two fixes for ixgbe, first resolves a link issue with DA
cables where we were not always freeing the firmware/software semaphore
after grabbing it.  Second stops caching whether the management firmware
was enabled, however since this is not static, we really need to verify
with each check.

Jacob provides six fixes/cleanups for ixgbe, most notably, correct
the stop_mac_link_on d3() to check the Core Clock Disable bit before
stopping link and to fully check to see if manage firmware is running or
could be enabled before bringing down the link.  Fix flow control
auto-negation for KR/KX/K4 interfaces, since setting up MAC link, the
cached autoc value and current autoc value were being incorrectly used to
determine whether link reset is required.

Emil provides a fix for ixgbe where there was a chance for aggressive
start_ndo_zmit() callers to sneak packets between enabling the Tx queues
and the link coming up.  To resolve this, move the call to enable Tx
queues to after the link is established.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch moves the call to enable Tx queues after the link is established.
Previously there was a chance for aggressive start_ndo_xmit() callers to
sneak packets between enabling the Tx queues and the link coming up.

In addition it replaces netif_tx_start_all_queues() with
netif_tx_wake_all_queues() to allow for flushing of the qdisc.

CC: Arun Sharma <asharma@fb.com>
Signed-off-by: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

We use to cache whether the MNG FW was enabled, how since this isn't
static we really need to verify with each check.  This patch makes that
change.

CC: Arun Sharma <asharma@fb.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Rather than assign several parameters in a row, we should use a for
loop, which reduces code size.

CC: Arun Sharma <asharma@fb.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch replaces some direct uses of pci_read_config_word with the
protected ixgbe_read_pci_cfg_word function, which checks for whether the
adapter is removed when LER is enabled. We shouldn't use the
pci_read_config_word calls directly because of these checks.

This patch also cleans up an unnecessary save of a pointer to the mac
object, as our standard style is to just use the hw pointer.

CC: Arun Sharma <asharma@fb.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch reverts the addition of the fiber_fixed type, which ended up
never being used. We don't have plans to support this type going
forward, and there is no reason to keep an unused type around polluting
the code.

Reverts: 4e8e1bca ("ixgbe: add new media type")
CC: Arun Sharma <asharma@fb.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch fixes flow control autonegotiation for KR/KX/K4 interfaces.
When setting up MAC link, the cached autoc value and current autoc value
were being incorrectly used to determine whether link reset is required.
This resulted in the driver ignoring and discarding flow control
negotiation changes that occur since the caching happened, as well as
when the mac was being setup.

This patch also splits the assignments for the 3 autoc variables into
their own block, and adds a comment explaining what each one means, in
order to help keep logic more straightforward while reading the code.

CC: Arun Sharma <asharma@fb.com>
Reported-by: Sourav Chatterjee <sourav.chatterjee@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Previously, we did a full check to see if MNG FW was running. Instead,
we should only check to see whether it could be enabled. Since it may
become active while down, we don't want to bring the link down.

CC: Arun Sharma <asharma@fb.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch corrects the stop_mac_link_on_d3 function in ixgbe_82599 by
checking the Core Clock Disable bit before stopping link.

CC: Arun Sharma <asharma@fb.com>
Reported-by: Chris Pavlas <chris.pavlas@intel.com>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Found several incorrect conditionals after calling the prot_autoc_*
functions. Likewise we weren't always freeing the FWSW semaphore after
grabbing it.   This would lead to DA cables being unable to link along with
possible other errors.

CC: Arun Sharma <asharma@fb.com>
CC: Emil Tantilov <emil.s.tantilov@intel.com>
Signed-off-by: Don Skidmore <donald.c.skidmore@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The use of __constant_<foo> has been unnecessary for quite awhile now.

Make these uses consistent with the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The use of __constant_<foo> has been unnecessary for quite awhile now.

Make these uses consistent with the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The use of __constant_<foo> has been unnecessary for quite awhile now.

Make these uses consistent with the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The use of __constant_<foo> has been unnecessary for quite awhile now.

Make these uses consistent with the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The use of __constant_<foo> has been unnecessary for quite awhile now.

Make these uses consistent with the rest of the kernel.
Signed-off-by: Joe Perches <joe@perches.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

For i350 VLAN stripping for VMs is not enabled in the VMOLR register but in
the DVMOLR register. Making the changes accordingly. It's not necessary to
unset the E1000_VMOLR_STRVLAN bit on i350 as the hardware will simply ignore
it.

Without this change if a VLAN is configured for a VF assigned to a guest
via (i.e.)
ip link set p1p1 vf 0 vlan 10
the VLAN tag will not be stripped from packets going into the VM. Which they
should be because the VM itself is not aware of the VLAN at all.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The current code would always return 0 for VLAN-encapsulated IP traffic.
One notable side effect was that VLAN traffic would never get prioritized
on OSD and OSX devices when priority queueing modes prio_queueing_tos or
prio_queueing_prec were enabled.
Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Stefan Raspl <raspl@linux.vnet.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Signed-off-by: Heiko Carstens <heiko.carstens@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Commit f9c41a62 introduced
a problem for SOCK_STREAM sockets, when only part of the
incoming iucv message is received by user space. In this
case the remaining data of the iucv message is lost.
This patch makes sure an incompletely received iucv message
is queued back to the receive queue.
Signed-off-by: Ursula Braun <ursula.braun@de.ibm.com>
Signed-off-by: Frank Blaschka <frank.blaschka@de.ibm.com>
Reported-by: Hendrik Brueckner <brueckner@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jeff Kirsher says:

====================
Intel Wired LAN Driver Updates

This series contains updates to i40e, i40evf, e1000e, ixgbe and ixgbevf.

Mitch adds support for the VF link state ndo which allows the PF driver
to control the virtual link state of the VF devices.  Added
support for viewing and modifying RSS hash options and RSS hash look-up
table programming through ethtool for i40evf.  Fixed complaint about
the use of min() where min_t() should be used in i40evf.

Anjali adds support for ethtool -k option for NTUPLE control for i40e.

Elizabeth cleans up and refactors i40e_open() to separate out the VSI
code into its own i40e_vsi_open().

Jesse enables the hardware feature head write back to avoid updating the
descriptor ring by marking each descriptor with a DD bit and instead
writes a memory location with an update to where the driver should clean
up to in i40e and i40evf.  Reduces context descriptors for i40e/i40evf
since we do not need context descriptors for every packet, only for
TSO or timesync.

Dan Carpenter fixes a potential array underflow in i40e_vc_process_vf_msg().

Dave fixes an e1000e hardware unit hang where the check for pending Tx work
when link is lost was mistakenly moved to be done only when link is first
detected to be lost.  Fixed a problem with poor network performance on
certain silicon in e1000e when configured for 100M HDX performance.

Carolyn adds register defines needed for time sync functions and the code
to call the updated defines.

Jacob adds the ixgbe function for writing PCI config word and checks
whether the adapter has been removed first.

Mark adds the bit __IXGBEVF_REMOVING to indicate that the module is being
removed because the __IXGBEVF_DOWN bit had been overloaded for this
purpose, but leads to trouble.  ixgbevf_down function can now prevent
multiple executions by doing test_and_set_bit on __IXGBEVF_DOWN.

v2:
- dropped patch Mitch's patch "i40evf: Support RSS option in ethtool"
  based on feedback from Ben Hutchings so that Mitch can re-work the
  patch solution

v3:
- removed unnecessary parenthesis in patch 1 based on feedback from David
  Miller
- changed a macro to get the next queue to a function in patch 2 based on
  feedback from David Miller
- added blank lines after variable declaration and code in two functions
  in patch 6 based on feedback from David Miller
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

The ixgbevf_down function can now prevent multiple executions by
doing test_and_set_bit on __IXGBEVF_DOWN. This did not work before
introduction of the __IXGBEVF_REMOVING bit, because of overloading
of __IXGBEVF_DOWN. Also add smp_mb__before_clear_bit call before
clearing the __IXGBEVF_DOWN bit.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Add a bit, __IXGBEVF_REMOVING, to indicate that the module is being
removed. The __IXGBEVF_DOWN bit had been overloaded for this purpose,
but that leads to trouble. A few places now check both __IXGBEVF_DOWN
and __IXGBEVF_REMOVING.
Signed-off-by: Mark Rustad <mark.d.rustad@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Inline with the current use for ixgbe_read_pci_cfg_word, create a
similar function for writing PCI config, which checks whether the
adapter has been removed first, if Live Error Recovery has been enabled.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Phil Schmitt <phillip.j.schmitt@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch adds defines needed for implementing the auxiliary time sync
functions and also changes code to call the updated defines instead of
the old.
Reported-by: Richard Cochran <ricahrdcochran@gmail.com>
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch causes the TCTL to be explicitly set to fix a problem with
poor network performance (throughput) on certain silicon when configured
for 100M HDX performance.

Cc: Todd Fujinaka <todd.fujinaka@intel.com>
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Acked-by: Bruce W. Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The check for pending Tx work when link is lost was mistakenly moved to be
done only when link is first detected to be lost.  It turns out there is a
small window of opportunity for additional Tx work to get queued up shortly
after link is dropped.

Move the check back to the place it was before in the watchdog task.  Put in
additional debug information for other reset paths and a final catch-all for
false hangs in the scheduled function that prints out the hardware hang
message.
Signed-off-by: Dave Ertman <davidx.m.ertman@intel.com>
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Bump to version 0.3.36 for i40e and 0.9.16 for i40evf.

Change-ID: I7b4ff97b32d2825181803c03c316381a7608a618
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

If "vf_id" is smaller than hw->func_caps.vf_base_id then it leads to
an array underflow of the pf->vf[] array.  This is unlikely to happen
unless the hardware is bad, but it's a small change and it silences a
static checker warning.

Fixes: 7efa84b7 ('i40e: support VFs on PFs other than 0')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

We don't need context descriptors for every packet, only tso
or timesync.  This fixes a bug in the driver where it would
always add a context even if all the passed in values
to the context descriptor function were 0/default values.

Change-ID: I0101d2b893380707b5c2de61aab3e16d4310e9a1
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The hardware supports a feature to avoid updating the descriptor
ring by marking each descriptor with a DD bit, and instead
writes a memory location with an update to where the driver
should clean up to.  Enable this feature.

Change-ID: I5da4e0681f0b581a6401c950a81808792267fe57
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This patch cleans up and moves a portion of i40e_open to i40e_vsi_open,
in order to have a shorter vsi_open function that does only that.

Change-ID: I1c418dda94dcfc0eb7d4386a70c330692ef5ecc9
Signed-off-by: Elizabeth Kappler <elizabeth.m.kappler@intel.com>
Signed-off-by: Akeem G Abodunrin <akeem.g.abodunrin@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

This enables option '-k/-K' in ethtool for NTUPLE control.
NTUPLE control requires a reset, to take effect. When the feature is
turned off, the SW list of stored FD SB filters gets cleaned up.

Change-ID: I9d564b67a10d4afa11de3b320d601c3d2e6edc1f
Signed-off-by: Anjali Singhai Jain <anjali.singhai@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Kavindya Deegala <kavindya.s.deegala@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Checkpatch complained in an earlier patch about using min(), but that
change would have been completely unrelated to the point of that patch.
So fix it here.

Change-ID: I2cd87b39cfd406850d283b88f259757a6bcd14cd
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

The HLUT programming loop in in i40evf_configure_rss was a) overly-
complicated, and b) just plain broken. Most of the entries ended up being
not written at all, so most of the flows ended up at queue zero.

Refactor the HLUT programming loop to simply walk through the registers
and write four values to each one, incrementing through the number of
available queues.

Change-ID: I75766179bc67e4e997187794f3144e28c83fd00d
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Commit 20d8435a (phy: micrel: add of configuration for LED mode) made the
obvious mistake when masking off  the LED mode bits: forgot to do a logical NOT
to the mask with which it ANDs the register value, so that unrelated bits are
cleared instead.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Ben Dooks <ben.dooks@codethink.co.uk>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This netdev op allows the PF driver to control the virtual link state of
the VF devices. This can be used to deny naughty VF drivers access to
the wire, or to allow VFs (regardless of temperament) to communicate
with each other over the device's internal switch even though external
link is down.

Add the actual ndo function, and modify vc_notify_link_state to check
the link status of each VF before sending a message in the case when
physical link changes state.

Change-ID: Ib5a6924da78c540789f21d26b5e8086d71c29384
Signed-off-by: Mitch Williams <mitch.a.williams@intel.com>
Signed-off-by: Catherine Sullivan <catherine.sullivan@intel.com>
Tested-by: Sibai Li <sibai.li@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>