The file uses u16 type but doesn't include its definition explicitly

I was getting this error when including this header in my driver:

  arch/mips/include/asm/mipsregs.h:644:33: error: unknown type name ‘u16’
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Reviewed-by: Steven J. Hill <Steven.Hill@imgtec.com>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6212/

we want the device tree to be unflattened into non init memory so it can be
accessed later by, for example, a probing function of a driver module.
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6210/

Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6209/

The defaults are not always applicable and it makes it hard for the bootloader
to override them. By removing it we give the bootloader full control over what
command line parameters to pass.

Without this change we will need to modify the built-in dtb to add bootloader
cmd line parameters or do some work to append them after we unflatten the device
tree.

Sead3 is a development board, that's why we want to be able to change boot
parameters on the fly from the bootloader.
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6208/

if the user sets memsize parameter in commandline or bootloader
environment, we use it to modify the built-in dtb memory size
Signed-off-by: Qais Yousef <qais.yousef@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6207/

Update the early_printk code to include linux/serial_bcm63xx.h which
provides the definitions for the UART block registers. While at it,
remove the inclusion of serial_bcm63xx.h which was just there to allow
smooth transition.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6203/

Now that the UART block defines have been moved to a separate file,
include that one and do not longer rely on the MIPS-specific
bcm63xx_regs.h header file.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6204/

Move the BCM63XX UART driver definitions to
include/linux/serial_bcm63xx.h such that we do not rely on the MIPS
BCM63XX code to provide these for us.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6202/

bcm_{readl,writel} macros expand to __raw_{readl,writel}, use these
directly such that we do not rely on the platform to provide these for
us. As a result, we no longer use bcm63xx_io.h, so remove that inclusion
too.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6201/

bcm63xx_irqs.h is included but we are not using anything from it, drop
that include.
Signed-off-by: Florian Fainelli <florian@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6205/

Remove usage of -mno-jals compiler flag when building a pure
microMIPS kernel. The -mno-jals flag only ever existed within
Mentor toolchains. Dropping this flag allows all FSF toolchains
to work.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6200/

This will be needed by the next patch to use said nodes for probing
via the device tree.
Signed-off-by: David Daney <david.daney@cavium.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6185/

This patch switches Malta from using the MIPS implementation of early
printk with Malta's prom_putchar to using the generic 8250_early
implementation. This offers a couple of advantages:

  - We duplicate less generic code.

  - The UART can be initialised rather than being reliant upon
    inheriting a valid setup from the bootloader.

The Malta console_config function is extended to initialise the early
console if no earlycon= kernel parameter is provided, inheriting the
modetty0 bootloader environment if present and falling back to a
default 38400n8r setup if not. This matches the behaviour used for the
regular console= parameter.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6183/

This patch causes the kernel to mux the SERIRQ interrupt to the SERIRQ
pin of the PIIX4 and to enable that interrupt. The kernel depends upon
the interrupt when using the SuperIO UARTs (ttyS0 & ttyS1) but
previously would not configure it, instead relying upon the bootloader
having done so. If that is not the case then the typical result is that
the system appears to hang once it reaches userland as no output is
displayed on the UART.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6182/

The RTC is used on Malta to estimate the clock frequency of the CPU &
optionally the GIC. However the kernel previously did not initialise the
RTC, instead relying upon the bootloader having done so. In order to
minimise dependencies which the kernel has upon the bootloader this
patch causes the kernel to initialise the RTC itself prior to making use
of it.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6184/

This variable seems to have been copied from Malta when SEAD3 support
was introduced, but is likewise unused. Remove it.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6172/

This variable was introduced by commit 96348c8f (of Ralf's historic
Linux/MIPS repository) "Remaining fixes for MIPS's eval boards." but
I don't see any use of it either then or now. Remove it.
Signed-off-by: Paul Burton <paul.burton@imgtec.com>
Reviewed-by: Markos Chandras <markos.chandras@imgtec.com>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6171/

Export symbols needed by the octeon-ethernet driver. The patch fixes a
build failure with CONFIG_OCTEON_ETHERNET=m.
Signed-off-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6166/

The following build error is seen if CONFIG_32BIT is undefined,
CONFIG_64BIT is defined, and CONFIG_MIPS32_O32 is undefined.

asm/syscall.h: In function 'mips_get_syscall_arg':
arch/mips/include/asm/syscall.h:32:16: error: unused variable 'usp' [-Werror=unused-variable]
cc1: all warnings being treated as errors

Fixes: c0ff3c53 ('MIPS: Enable HAVE_ARCH_TRACEHOOK')
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6160/

The boot hangs early on EBH5600 board when octeon_fdt_pip_iface() is
trying enumerate a non-existant interface. The actual hang happens in
cvmx_helper_interface_get_mode():

	mode.u64 = cvmx_read_csr(CVMX_GMXX_INF_MODE(interface));

when interface == 4. We can avoid this situation by first checking that
the interface exists in the DTB.
Signed-off-by: Aaro Koskinen <aaro.koskinen@nsn.com>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6101/

When booting with in-kernel DTBs, the pruning code will enumerate
interfaces 0-4. However, there is memory reserved only for 4 so some
other data will get overwritten by cvmx_helper_interface_enumerate().
Signed-off-by: Aaro Koskinen <aaro.koskinen@nsn.com>
Acked-by: David Daney <david.daney@cavium.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6102/

Signed-off-by: Antony Pavlov <antonynpavlov@gmail.com>
Acked-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5927/

Only one MIPS development board actually supports enabling/disabling DMA
coherency at runtime, so it's not a good idea to push the overhead of
checking that configuration setting onto every other supported target as
well.
Signed-off-by: Felix Fietkau <nbd@openwrt.org>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/5912/

Clean-up code according to the 'checkpatch.pl' script.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Reviewed-by: Qais Yousef <Qais.Yousef@imgtec.com>
Patchwork: http://patchwork.linux-mips.org/patch/6097/Reviewed-by: John Crispin <blogic@openwrt.org>

Malta with multi-core CM platforms can now use APRP functionality.
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Reviewed-by: Qais Yousef <Qais.Yousef@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6096/

This patch adds RTLX API support for platforms having a CMP.
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Reviewed-by: Qais Yousef <Qais.Yousef@imgtec.com>
Patchwork: http://patchwork.linux-mips.org/patch/6095/Reviewed-by: John Crispin <blogic@openwrt.org>

Split the RTLX functionality in preparation for adding support for CMP
platforms. Common functions remain in the original file and a new file
contains code specific to platforms that do not have a CMP.
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Reviewed-by: Qais Yousef <Qais.Yousef@imgtec.com>
Patchwork: http://patchwork.linux-mips.org/patch/6093/Reviewed-by: John Crispin <blogic@openwrt.org>

This patch adds VPE loader support for platforms having a CMP.
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Reviewed-by: Qais Yousef <Qais.Yousef@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6092/

Split the VPE functionality in preparation for adding support
for CMP platforms. Common functions remain in the original file
and a new file contains code specific to platforms that do not
have a CMP present.
Signed-off-by: Deng-Cheng Zhu <dengcheng.zhu@imgtec.com>
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Reviewed-by: Qais Yousef <Qais.Yousef@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6094/

This patch accomplishes the following:

  * Clean up wording on all MIPS MT configuration menu items.
  * Simplify and neaten up options selected by MIPS_MT_SMP.
  * Make MIPS_MT_SMTC support as deprecated.
  * Make MIPS_CMP support to depend on MIPS_MT_SMP also.
  * Remove redundant options selected by MIPS_CMP.
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6019/

Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6152/

The interAptiv is a power-efficient multi-core microprocessor
for use in system-on-chip (SoC) applications. The interAptiv combines
a multi-threading pipeline with a coherence manager to deliver improved
computational throughput and power efficiency. The interAptiv can
contain one to four MIPS32R3 interAptiv cores, system level
coherence manager with L2 cache, optional coherent I/O port,
and optional floating point unit.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6163/

Add processor identifiers for UP and MT interAptiv processors.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6151/

Add a new mips/segments debugfs file to print the 6 segmentation
control registers for supported cores. A sample from a proAptiv core
is given below:
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6137/
Segment   Virtual    Size   Access Mode   Physical   Caching   EU
-------   -------    ----   -----------   --------   -------   --
   0      e0000000   512M      MK           UND         U       0
   1      c0000000   512M      MSK          UND         U       0
   2      a0000000   512M      UK           000         2       0
   3      80000000   512M      UK           000         3       0
   4      40000000    1G       MUSK         UND         U       1
   5      00000000    1G       MUSK         UND         U       1
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Steven J. Hill <Steven.Hill@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>

The Fixed Page Size TLB (FTLB) is a set-associative dual entry TLB. Its
purpose is to reduce the number of TLB misses by increasing the effective
TLB size and keep the implementation complexity to minimum levels.
A supported core can have both VTLB and FTLB.
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6139/

The TLBINVF instruction can be used to flush the entire VTLB.
This eliminates the need for the TLBWI loop and improves performance.
Reviewed-by: Paul Burton <paul.burton@imgtec.com>
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6138/

Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6136/

Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6135/

The proAptiv Multiprocessing System is a power efficient multi-core
microprocessor for use in system-on-chip (SoC) applications.
The proAptiv Multiprocessing System combines a deep pipeline
with multi-issue out of order execution for improved computational
throughput. The proAptiv Multiprocessing System can contain one to
six MIPS32r3 proAptiv cores, system level coherence
manager with L2 cache, optional coherent I/O port, and optional
floating point unit.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6134/

Add processor identifiers for single core and multi-core
proAptiv processors.
Signed-off-by: Leonid Yegoshin <Leonid.Yegoshin@imgtec.com>
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: John Crispin <blogic@openwrt.org>
Patchwork: http://patchwork.linux-mips.org/patch/6133/