- 18 Jun, 2012 9 commits
-
-
Ezequiel García authored
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Dan Carpenter authored
The test here is never true because '&' was used instead of '|'. It was the same as: if (status & ((1<<16) & (1<<17)) ... Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Albert Wang authored
It should be a mistake due to copy & paste in header file Correct it in videobuf2-dma-config.h for avoiding duplicate include it Change-Id: I1f71fcec2889c033c7db380c58d9a1369c5afb35 Signed-off-by: Albert Wang <twang13@marvell.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Jarod Wilson authored
For one, the driver device pointer needs to be filled in, or the lirc core will refuse to load the driver. And we really need to wire up all the platform_device bits. This has been tested via the lirc sourceforge tree and verified to work, been sitting there for months, finally getting around to sending it. :\ CC: Josh Boyer <jwboyer@redhat.com> Signed-off-by: Jarod Wilson <jarod@redhat.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Klaus Schmidinger authored
stb0899_read_ber() takes 500ms (half a second!) to deliver the current BER value. Apparently it takes 5 subsequent readings, with a 100ms pause between them (and even before the first one). This is a real performance brake if an application freqeuently reads the BER of several devices. The attached patch reduces this to a single reading, with no more pausing. I didn't observe any negative side effects of this change. Signed-off-by: Klaus Schmidinger <Klaus.Schmidinger@tvdr.de> Cc: Manu Abraham <abraham.manu@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
volokh authored
Signed-off-by: Volokh Konstantin <volokh84@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Sachin Kamat authored
Fixes the following sparse warnings: drivers/media/video/s5p-fimc/fimc-lite-reg.c:218:6: warning: symbol 'flite_hw_set_out_order' was not declared. Should it be static? drivers/media/video/s5p-fimc/fimc-mdevice.c:183:5: warning: symbol '__fimc_pipeline_shutdown' was not declared. Should it be static? drivers/media/video/s5p-fimc/fimc-mdevice.c:1013:12: warning: symbol 'fimc_md_init' was not declared. Should it be static? drivers/media/video/s5p-fimc/fimc-mdevice.c:1024:13: warning: symbol 'fimc_md_exit' was not declared. Should it be static? drivers/media/video/s5p-fimc/fimc-core.c:466:5: warning: symbol 'fimc_set_color_effect' was not declared. Should it be static? drivers/media/video/s5p-fimc/fimc-capture.c:1163:5: warning: symbol 'enclosed_rectangle' was not declared. Should it be static? Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Acked-by: Sylwester Nawrocki <s.nawrocki@samsung.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Dan Carpenter authored
Sparse complains if about using unsigned long. videobuf-dma-contig.c:47:67: warning: restricted gfp_t degrades to integer videobuf-dma-contig.c:47:65: warning: incorrect type in argument 2 (different base types) videobuf-dma-contig.c:47:65: expected restricted gfp_t [usertype] gfp_mask videobuf-dma-contig.c:47:65: got unsigned long Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Jean-Francois Moine authored
Hans de Goede accepted to be the new gspca maintainer. Signed-off-by: Jean-François Moine <moinejf@free.fr> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
- 14 Jun, 2012 1 commit
-
-
Sakari Ailus authored
Patch id 6016af82 ("[media] v4l2: use __u32 rather than enums in ioctl() structs") unintentionally changes the type of the format field in struct v4l2_create_buffers from struct v4l2_format to __u32. Revert that change. Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
- 24 May, 2012 3 commits
-
-
Laurent Pinchart authored
The pixel rate control is required by the OMAP3 ISP driver and should be implemented by all media controller-compatible sensor drivers. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Laurent Pinchart authored
The pixel rate control is required by the OMAP3 ISP driver and should be implemented by all media controller-compatible sensor drivers. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Laurent Pinchart authored
The pixel rate control is required by the OMAP3 ISP driver and should be implemented by all media controller-compatible sensor drivers. Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by: Sakari Ailus <sakari.ailus@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
- 21 May, 2012 1 commit
-
-
Mauro Carvalho Chehab authored
changeset 75c7dbca added a wrong PCI ID address by mistake. Remove it. Reported-by: Remi Schwartz <remi.schwartz@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
- 20 May, 2012 26 commits
-
-
Ondrej Zary authored
Add support for SF16-FMD card to radio-sf16fmi driver. Only new PnP ID is added and texts changed. Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Michel Machado authored
This patch just removes the second assignment "rc->priv = &loopdev;" that happens a fews lines after the first one. Signed-off-by: Michel Machado <michel@digirati.com.br> CC: Mauro Carvalho Chehab <mchehab@infradead.org> CC: "David Härdeman" <david@hardeman.nu> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
remi schwartz authored
Signed-off-by: Remi Schwartz <remi.schwartz@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Ismael Luceno authored
This driver is for USB devices, but was incorrectly listed under V4L_PCI_DRIVERS. Signed-off-by: Ismael Luceno <ismael.luceno@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Antti Palosaari authored
Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Ondrej Zary authored
Add PnP support to radio-sf16fmr2 driver to support SF16-FMD2 card (SB16 + TEA5757). The driver can now handle two cards (FMR2 is hardwired to 0x384, FMD2 can be put at 0x384 or 0x284 by PnP). Tested with both SF16-FMR2 and SF16-FMD2 (the can work at the same time by using kernel parameter "pnp_reserve_io=0x384,2" so the FMD2 is put at 0x284). Signed-off-by: Ondrej Zary <linux@rainbow-software.org> Acked-by: Hans Verkuil <hans.verkuil@cisco.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Sakari Ailus authored
Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Sakari Ailus authored
Add support for uncompressed 8-bit raw bayer formats. Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Sakari Ailus authored
Implement more generic quirk registers than just limit and capability registers. This comes with the expense of a little bit more access time so these should be only used when really needed. Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Sakari Ailus authored
Some sensors do use binning but do not have valid limits in binning registers. Use non-binning limits in that case. Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Sakari Ailus authored
rval was not properly initialised in smiapp_read_nvm(). Do that. Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Sakari Ailus authored
The pre_pll divisor must be such that ext_clk / pre_pll divisor does not result in a frequency that is greater than pll_ip_clk_freq. Fix this. Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Sakari Ailus authored
Some sensors only allow 8-bit access, so use safe 8-bit access before the sensor has been identified. Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Sakari Ailus authored
Some sensors implement only 8-bit read functionality and fail on wider reads. Add a quirk flag for such sensors. Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Sakari Ailus authored
Pass struct sensor to register access commands. This allows taking quirks into account in register access. Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Sakari Ailus authored
Instead of providing a function in platform data, allow also providing the name of the external clock and use it through the clock framework. Signed-off-by: Sakari Ailus <sakari.ailus@maxwell.research.nokia.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Antti Palosaari authored
Report SNR in 0.1 dB scale instead of raw hardware register values. Signed-off-by: Antti Palosaari <crope@iki.fi> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Jozsef Marton authored
gspca_pac7302 module supports the webcam with usb id: 093a:2627. It is a Genius FaceCam 300. The module does not need any changes but listing the usb id along with a vertical flip flag. The included patch adds this to the module source. Signed-off-by: Jozsef Marton <jmarton@users.sourceforge.net> Acked-by: Márton Németh <nm127@freemail.hu> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Malcolm Priestley authored
Continuous flip of bit2 reg 0x70 can cause device to become unresponsive. Also correct reg read mistake. Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Igor M. Liplianin authored
Trival patch to get it working with my cards stuff. Signed-off-by: Igor M. Liplianin <liplianin@me.by> Acked-by: Malcolm Priestley <tvboxspy@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Mauro Carvalho Chehab authored
This device supports V4L2_STD_ALL, but its check for 60Hz standards is broken, as NTSC is not the only standard that uses 60Hz. Cc: Federico Vaga <federico.vaga@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Federico Vaga authored
V4L2 driver for the Video Input Port within STA2X11 board Signed-off-by: Federico Vaga <federico.vaga@gmail.com> Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com> Cc: Alan Cox <alan@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Federico Vaga authored
Signed-off-by: Federico Vaga <federico.vaga@gmail.com> Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com> Cc: Alan Cox <alan@linux.intel.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Federico Vaga authored
Video user controls such as brightness, contrast, saturation, and hue are now handled. Signed-off-by: Federico Vaga <federico.vaga@gmail.com> Acked-by: Giancarlo Asnaghi <giancarlo.asnaghi@st.com> Cc: Alan Cox <alan@linux.intel.com> Cc: Richard Röjfors <richard.rojfors.ext@mocean-labs.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Ben Hutchings authored
fintek-cir, ite-cir and nuvoton-cir may try to free an I/O region and/or IRQ handler that was never allocated after a failure in their respective probe functions. Add and use separate labels on the failure path so they will do the right cleanup after each possible point of failure. Compile-tested only. Signed-off-by: Ben Hutchings <ben@decadent.org.uk> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-
Malcolm Priestley authored
Correct incorrect scancode for KEY_1 Signed-off-by: Malcolm Priestley <tvboxspy@gmail.com> Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
-