Mutliple issues.  INIT_ZM_I2C_BYTE/INIT_I2C_BYTE didn't even try and
use the register value, and all the handlers were using the wrong
slave address.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

It appears to be meant to reference the second "default index".
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

We may not have parsed the entry yet if the i2c_index is for an i2c bus
that's not referenced by a DCB encoder.

This could be done oh so much more nicely, except we have to care about
prehistoric DCB tables too, and they make life painful.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Some handlers don't report specific errors, but we still *really* want to
know if we failed to parse a complete init table.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

We really want to be able to distinguish between INIT_DONE and an actual
error sometimes.  This commit fixes up several lazy "return 0;" to be
actual error codes, and explicitly reserves "0" as "success, but stop
parsing this table".
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

There appears to be some kind of switch on certain chips to control whether
the DP auxch or traditional i2c bus will be operational on a connector,
this commit hopefully fixes nouveau to do the right thing.

Likely only relevent on chips with DP outputs.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

I actually thought these were gone already when the initial commit was
done.. I guess not!
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Marcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Signed-off-by: Marcin Kościelnicki <koriakin@0x04.net>
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>

Reported-by: Dan Carpenter
Signed-off-by: Dave Airlie <airlied@redhat.com>

- Use radeon hpd enum consistently (in both hotplug and dp)
- Legacy r100 with DVI should be HPD_1 not NONE
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Some LVDS connectors don't have a ddc bus, so reset the
ddc bus to invalid before parsing the next connector
to avoid using stale ddc bus data.  Should fix
fdo bug 28164.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Cc: stable@kernel.org
Signed-off-by: Dave Airlie <airlied@redhat.com>

The current initialisation code probes 'unsupported' AGP devices
simply by calling its own probe function.  It does not lock these
devices or even check whether another driver is already bound to
them.

We must use the device core to manage this.  So if the specific
device id table didn't match anything and agp_try_unsupported=1,
switch the device id table and call driver_attach() again.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>

SIS 760 is listed in the device tables for both amd64-agp and sis-agp.
amd64-agp is apparently preferable since it has workarounds for some
BIOS misconfigurations that sis-agp doesn't handle.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Dave Airlie <airlied@redhat.com>

* anholt/drm-intel-next: (515 commits)
  drm/i915: Fix out of tree builds
  drm/i915: move fence lru to struct drm_i915_fence_reg
  drm/i915: don't allow tiling changes on pinned buffers v2
  drm/i915: Be extra careful about A/D matching for multifunction SDVO
  drm/i915: Fix DDC bus selection for multifunction SDVO
  drm/i915: cleanup mode setting before unmapping registers
  drm/i915: Make fbc control wrapper functions
  drm/i915: Wait for the GPU whilst shrinking, if truly desperate.
  drm/i915: Use spatio-temporal dithering on PCH
  [MTD] Remove zero-length files mtdbdi.c and internal.ho
  pata_pcmcia / ide-cs: Fix bad hashes for Transcend and kingston IDs
  libata: Fix several inaccuracies in developer's guide
  slub: Fix bad boundary check in init_kmem_cache_nodes()
  raid6: fix recovery performance regression
  KEYS: call_sbin_request_key() must write lock keyrings before modifying them
  KEYS: Use RCU dereference wrappers in keyring key type code
  KEYS: find_keyring_by_name() can gain access to a freed keyring
  ALSA: hda: Fix 0 dB for Packard Bell models using Conexant CX20549 (Venice)
  ALSA: hda - Add quirk for Dell Inspiron 19T using a Conexant CX20582
  ALSA: take tu->qlock with irqs disabled
  ...

print an error if these fail.
Signed-off-by: Dave Airlie <airlied@redhat.com>

This patch is a combination of the previous two profile
patches, but without the index bugs.  It cleans up and
fixes some issues with pm profile setup on r6xx chips.
Some tables have different orderings for the power states,
also, r600 only has 1 clock mode per power state. On
desktop cards there are no battery modes, so the low and high
power states are the same.  For the low profile case, choose
the lower clock mode.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

- Separate dynpm and profile based power management methods.  You can select the pm method
  by echoing the selected method ("dynpm" or "profile") to power_method in sysfs.
- Expose basic 4 profile in profile method
  "default" - default clocks
  "auto" - select between low and high based on ac/dc state
  "low" - DC, low power mode
  "high" - AC, performance mode
  The current base profile is "default", but it should switched to "auto" once we've tested
  on more systems.  Switching the state is a matter of echoing the requested profile to
  power_profile in sysfs.  The lowest power states are selected automatically when dpms turns
  the monitors off in all states but default.
- Remove dynamic fence-based reclocking for the moment.  We can revisit this later once we
  have basic pm in.
- Move pm init/fini to modesetting path.  pm is tightly coupled with display state.  Make sure
  display side is initialized before pm.
- Add pm suspend/resume functions to make sure pm state is properly reinitialized on resume.
- Remove dynpm module option.  It's now selectable via sysfs.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

The lowest power states often cause display problems, so only enable
them when all displays are off.
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

GUI idle interrupts don't seem to work terribly well on r500 and earlier,
so let's use a fence instead.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

We need to handle the ring while we've already locked it, so split out
the allocation and commit functions in order to allow them to be used.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

voltage drop, dynamic voltage, dynamic sclk, pcie lane adjust, etc,
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

voltage drop, dynamic voltage, dynamic sclk, pcie lane adjust, etc,
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

since derefing the object might free it.
Signed-off-by: Dave Airlie <airlied@redhat.com>

- disable gui idle interrupt use
  Seems to hang some r5xx chips
- move vbl range check into
  existing vbl check function in
  radeon_pm.c
- disable crtc mc acccess for the
  whole reclocking process
Signed-off-by: Alex Deucher <alexdeucher@gmail.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

Will be used by nouveau driver also in the near future.
Signed-off-by: Ben Skeggs <bskeggs@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

This seems to be relatively stable now, so enable it for these chipsets
too.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

The vblank interrupt on r600 doesn't seem to be especially reliable, so
perform some sanity checks before the actual reclock.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

The ttm code could take vram_mutex followed by cp_mutex, while the
reclocking code would do the reverse. Hilarity could ensue.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>

We need to choose the correct PM state to transition into before starting
the actual change. Call radeon_get_power_state() at the top of the clock
setting to do so.
Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>