Merge tag 'omap-cleanup-b2-for-3.8' of git://git.kernel.org/pub/scm/linux/kernel/git/pjw/omap-pending into omap-for-v3.8/cleanup-prcm

Second set of OMAP PRCM cleanups for 3.8.

These patches remove the use of omap_prcm_get_reset_sources() from the
OMAP watchdog driver, and remove mach-omap2/prcm.c and
plat-omap/include/plat/prcm.h.

Basic test logs for this branch on top of Tony's cleanup-prcm branch
at commit 7fc54fd3 are here:

    http://www.pwsan.com/omap/testlogs/prcm_cleanup_b_3.8/20121108151646/

However, cleanup-prcm at 7fc54fd3 does not include some fixes
that are needed for a successful test.  With several reverts,
fixes, and workarounds applied, the following test logs were
obtained:

    http://www.pwsan.com/omap/testlogs/TEST_prcm_cleanup_b_3.8/20121108151930/

 which indicate that the series tests cleanly.

This second pull request updates one of the patches which broke
with rmk's allnoconfigs, and also updates the tag description to
indicate that 7fc54fd3 is building cleanly here.

arch/arm/mach-omap2/prcm.c and arch/arm/plat-omap/include/plat/prcm.h
are now completely unused and can be removed.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>

The hwmod code unconditionally calls _omap4_disable_module() on all
SoCs when a module doesn't enable correctly.  This "worked" due to the
weak function omap4_cminst_wait_module_idle() in
arch/arm/mach-omap2/prcm.c, which was a no-op.  But now those weak
functions are going away - they should not be used.  So this patch
will now call the SoC-specific disable_module code, assuming it
exists.

Needs to be done before the weak function is removed, otherwise AM33xx
will crash early in boot.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>

Consolidate all of the copies of MAX_MODULE_HARDRESET_WAIT and
MAX_MODULE_SOFTRESET_WAIT into one place, arch/arm/mach-omap2/prm.h.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>

Split omap2_set_globals_prcm() into PRM, CM, and PRCM_MPU variants, since
these are all separate IP blocks.  This should make it easier to move the
PRM, CM, PRCM_MPU code into drivers/ in future patchsets.

At this point arch/arm/plat-omap/include/plat/prcm.h is empty; a
subsequent patch will remove it, and remove the #include from all the
files that #include it.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>

Now that all users of mach-omap2/omap2_cm_wait_idlest() have been removed,
delete the function and its supporting macros and prototypes.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>

Convert the OMAP clock code's _omap2_module_wait_ready() to use
SoC-independent CM functions that are provided by the CM code, rather
than using a deprecated function from mach-omap2/prcm.c.

This facilitates the future conversion of the CM code to a driver, and
also removes a mach-omap2/prcm.c user.  mach-omap2/prcm.c will be removed
by a subsequent patch.

Some modules have IDLEST registers that aren't in the CM module, such
as the AM3517 IDLEST bits.  So we also need a fallback function for
these non-CM odd cases.  Create a temporary one in mach-omap2/clock.c,
intended to exist until the SCM drivers are ready.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>

Convert the OMAP2xxx APLL code to use omap2_cm_wait_module_ready(),
and move the low-level CM register manipulation functions to
mach-omap2/cm2xxx.c.  The objectives here are to remove the dependency
on the deprecated omap2_cm_wait_idlest() function in
mach-omap2/prcm.c, so that code can be removed later; and move
low-level register accesses to the CM IP block to the CM code, which
will soon be moved into drivers/.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>

Modify the board files to use the SoC-specific system restart
functions.  At this point it's possible to remove omap_prcm_restart()
from mach-omap2/prcm.c.

While removing the prototypes for the now-unused restart functions, clean
up a few more obsolete prototypes in mach-omap2/clock.h.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>

Split omap_prcm_restart() from mach-omap2/prcm.c into SoC-specific
variants.  These functions need to be able to save the reboot reason
into the scratchpad RAM.  This implies a dependency on both the PRM
and SCM IP blocks, so they've been moved into their own file.  This
will eventually call functions in the PRM and SCM drivers, once those
are created.

Vaibhav Hiremath <hvaibhav@ti.com> identified an unused prototype in
the first version of this patch - now removed.  Tony Lindgren
<tony@atomide.com> noted a compile problem with some RMK Kconfigs;
resolved in this patch.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Vaibhav Hiremath <hvaibhav@ti.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>
Cc: Tony Lindgren <tony@atomide.com>

Collect all of the virt_prcm_set-specific clocktype code into
mach-omap2/clkt2xxx_virt_prcm_set.c.  Remove its dependency on the
'sclk' and 'vclk' global variables.  Those variables will be removed
by subsequent patches.

This is part of the process of cleaning up the OMAP2xxx clock code
and preparing for the removal of the omap_prcm_restart() function.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>

Remove the global 'dclk' variable, instead replacing it with a
variable local to the dpllcore clock type C file.  This removes some
of the special-case code surrounding the OMAP2xxx clock init.

This patch is a prerequisite for the removal of the
omap_prcm_restart() code from arch/arm/mach-omap2/prcm.c.  It also
cleans up some special-case OMAP2xxx clock code in the process.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>

Add SoC reset functions into the PRM code.  These functions are based
on code from mach-omap2/prcm.c.  They reset the SoC using the CORE DPLL
reset method (as opposed to one of the other two or three chip reset
methods).

Adding them here will facilitate their removal from
arch/arm/mach-omap2/prcm.c.  (prcm.c is deprecated.)
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>

Get rid of the mach-omap2/common.c globals by moving the global
initialization for IP block addresses that must occur early into
mach-omap2/io.c.  In the process, remove the *_map_common_io*() and
SoC-specific *set_globals* functions.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>

omap_prcm_get_reset_sources() is now unused; so, remove it.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Tested-by: Vaibhav Hiremath <hvaibhav@ti.com>

Previously the OMAP watchdog driver used a non-standard way to report
the chip reset source via the GETBOOTSTATUS ioctl.  This patch
converts the driver to use the standard WDIOF_* flags for this
purpose.

This patch may break existing userspace code that uses the existing
non-standard data format returned by the OMAP watchdog driver's
GETBOOTSTATUS ioctl.  To fetch detailed reset source information,
userspace code will need to retrieve it directly from the CGRM or PRM
drivers when those are completed.

Previously, to fetch the reset source, the driver either read a
register outside the watchdog IP block (OMAP1), or called a function
exported directly from arch/arm/mach-omap2.  Both approaches are
broken.  This patch also converts the driver to use a platform_data
function pointer.  This approach is temporary, and is due to the lack
of drivers for the OMAP16xx+ Clock Generation and Reset Management IP
block and the OMAP2+ Power and Reset Management IP block.  Once
drivers are available for those IP blocks, the watchdog driver can be
converted to call exported functions from those drivers directly.
At that point, the platform_data function pointer can be removed.

In the short term, this patch is needed to allow the PRM code to be
removed from arch/arm/mach-omap2 (it is being moved to a driver).

This version integrates a fix from Jon Hunter <jon-hunter@ti.com>
that avoids a NULL pointer dereference in a DT-only boot, and integrates
a patch commit message fix from Felipe Balbi <balbi@ti.com>.
Signed-off-by: Paul Walmsley <paul@pwsan.com>
Cc: Wim Van Sebroeck <wim@iguana.be>
Acked-by: Wim Van Sebroeck <wim@iguana.be>
[paul@pwsan.com: integrated pdata fix from Jon Hunter]
Cc: Jon Hunter <jon-hunter@ti.com>
[paul@pwsan.com: integrated changelog fix from Felipe Balbi]
Cc: Felipe Balbi <balbi@ti.com>

Merge tag 'for_3.8-pm-voltage' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap-pm into omap-for-v3.8/pm

OMAP voltage layer updates towards supporting auto-retention/auto-off

Merge tag 'for_3.8-pm-sr' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap-pm into omap-for-v3.8/pm

OMAP: SmartReflex: pass device-independent data via platform_data

Merge tag 'for_3.8-cleanup-pm' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-omap-pm into omap-for-v3.8/pm

Minor pr_warn() cleanup for OMAP2+ Voltage Processor (VP)

Add OMAP4460 OPP definitions for voltage and frequencies based on
OMAP4460 ES1.0 DM Operating Condition Addendum Version 0.1

The following exceptions are present:
* Smartreflex support is still on experimental mode: the gains and min
  limits are currently pending characterization data. Currently OMAP4430 values
  are used.
* Efuse offset for core OPP100-OV setting is not clear in documentation.
* IVA OPPs beyond OPP100 are disabled due to the delta between max OMAP4460
  current requirements and Phoenix Max supply on VCORE2 in the default
  configuration - boards which have supply which can support this should
  explicitly call opp_enable and enable the same.
* MPU OPPs > OPPTURBO can easily be detected using a efuse burnt - currently
  disabled pending clock changes to support DCC feature.

[nm@ti.com: cleanups and updates from Datamanual]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
[t-kristo@ti.com: rebased to linux-3.6-rc5]
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

With the new parameters, I2C can now be put to high speed mode for
better performance.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

VC code now provides a table of pre-calculated I2C setup parameters,
which will be used based on the capacitance value calculated for the I2C
trace on the PCB. A default trace length of 6.3cm is used unless board
defines its own value during init. The parameters set will be the I2C
internal pull setup and the I2C timing parameters for high speed use
mode. Full speed mode is not supported as of now.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

RACEN bit should only be set if the voltage and command register addresses
are the same.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

This is no longer needed as the ramp times are calculated from
voltage deltas + slew rates.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

As vddmin / vddmax voltages for the pmic only describe the pmic
capabilities now, change the voltages to be according to spec.
TWL data manuals give following values:

TWL4030 (SWCS019L) : VDD1: 600mV ... 1450mV, VDD2: 600mV ... 1500mV
TWL5030 (SWCS030E) : VDD1: 600mV ... 1450mV, VDD2: 600mV ... 1500mV
TWL6030 (SWCS045A) : 0V ... 2100mV
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

We now use the previously defined oscillator setup / shutdown times
to calculate the register values for CLKSETUP.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Now we select the vddmin and vddmax values based on both pmic and
voltage processor data, this allows usage of different power ICs.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

This contains startup and shutdown times for the oscillator. By default
use ULONG_MAX. Oscillator setup is used for calculating and setting up
latencies for sleep modes that disable oscillator.

Based on a patch from Nishanth Menon <nm@ti.com>.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

OMAP4 VC code now uses voltage deltas + slew rates for calculating
actual ramp times for voltage changes. Both retention / sleep +
off mode voltage ramp times are setup at the same time during
initialization.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

OMAP4 has two VOLTSETUP registers. One is controlling retention and
sleep voltage setup times, the other one off mode setup times. Both
of these need to be setup for stable behavior of the device.
The code setting up the new register will be added in the next
patch.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

OMAP3 VC code now uses voltage deltas + slew rates for calculating actual
ramp times for voltage changes. Previously a static value was used.
Two calculation methods are provided: i2c_timings and off_timings.
I2C timings are used during retention or off mode transition which
is initiated over I2C, and OFF timings are used if PMIC signal
(nsleep) is used to control all the off mode voltages at the same time.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

These new structs will hold the sleep voltage levels (omap_vc_params)
and voltage processor min / max voltages (omap_vp_params.) Previously
these were part of the PMIC struct, but they do not really belong there,
as they are OMAP chip specific, not PMIC specific parameters. voltdm
code is also changed to use the new structs.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

These are now called vddmin and vddmax, as these fields will be used
globally for selecting voltage ranges for a pmic channel, and not
only for voltage processor.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Every PMIC has it's own eccentricities, For example, one of the
PMIC has MSB set to 1 for a specific function - voltage enable!
using an hardcoded value specific for TWL when copied over to
such an implementation causes the system to crash as the MSB bit
was 0 and the voltage got disabled!.

Instead we use actual values and depend on the convertion routines
to abstract out the eccentricities of each PMIC.

With this, we can now move the voltages to a common location in
voltage.h as they are no longer dependent on PMICs and expect the
PMIC's conversion routines to set a cap if the voltage is out of
reach for the PMIC.
Reported-by: Jon Hunter <jon-hunter@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Vishwanath BS <vishwanath.bs@ti.com>
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Kevin Hilman <khilman@ti.com>

Pull NFS client bugfixes from Trond Myklebust:

 - Fix a bunch of deadlock situations:
   * State recovery can deadlock if we fail to release sequence ids
     before scheduling the recovery thread.
   * Calling deactivate_super() from an RPC workqueue thread can
     deadlock because of the call to rpc_shutdown_client.

 - Display the device name correctly in /proc/*/mounts

 - Fix a number of incorrect error return values:
   * When NFSv3 mounts fail due to a timeout.
   * On NFSv4.1 backchannel setup failure
   * On NFSv4 open access checks

 - pnfs_find_alloc_layout() must check the layout pointer for NULL

 - Fix a regression in the legacy DNS resolved

* tag 'nfs-for-3.7-4' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
  NFS4: nfs4_opendata_access should return errno
  NFSv4: Initialise the NFSv4.1 slot table highest_used_slotid correctly
  SUNRPC: return proper errno from backchannel_rqst
  NFS: add nfs_sb_deactive_async to avoid deadlock
  nfs: Show original device name verbatim in /proc/*/mount{s,info}
  nfsv3: Make v3 mounts fail with ETIMEDOUTs instead EIO on mountd timeouts
  nfs: Check whether a layout pointer is NULL before free it
  NFS: fix bug in legacy DNS resolver.
  NFSv4: nfs4_locku_done must release the sequence id
  NFSv4.1: We must release the sequence id when we fail to get a session slot
  NFS: Wait for session recovery to finish before returning

Pull thermal management & ACPI update from Zhang Rui,

Ho humm.  Normally these things go through Len.  But it's just three
small fixes, I guess I can pull directly too.

* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/rzhang/linux:
  exynos4_tmu_driver_ids should be exynos_tmu_driver_ids.
  ACPI video: Ignore errors after _DOD evaluation.
  thermal: solve compilation errors in rcar_thermal

Pull i2c embedded fixes from Wolfram Sang:
 "Two patches are usual stuff.

  The bigger patch is needed to correct a wrong decision made in this
  merge window.  We hoped to get the PIOQUEUE mode in the mxs driver
  working with DMA, but it turned out to be too broken (leading to data
  loss), so we now think it is best to remove it entirely and work only
  with DMA now.  The patch should be in 3.7.  IMO, so users never get
  the chance to use both modes in parallel."

* 'i2c-embedded/for-current' of git://git.pengutronix.de/git/wsa/linux:
  i2c: tegra: set irq name as device name
  i2c-nomadik: Fixup clock handling
  i2c: mxs: remove broken PIOQUEUE support

Pull drm fixes from Dave Airlie:
 "Scattered selection of fixes:

   - radeon: load detect fixes from SuSE/AMD
   - intel: misc i830, sdvo regression, vesafb kickoff ums fix
   - exynos: maintainers entry update + fixes
   - udl: fix stride scanout issue

  it's slightly bigger than I'd probably like, but nothing looked
  dangerous enough to hold off on."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/udl: fix stride issues scanning out stride != width*bpp
  drm/radeon: add load detection support for ext DAC on R200 (v2)
  DRM/radeon: For single CRTC GPUs move handling of CRTC_CRT_ON to crtc_dpms().
  DRM/Radeon: Fix TV DAC Load Detection for single CRTC chips.
  DRM/Radeon: Clean up code in TV DAC load detection.
  drm/radeon: fix ATPX function documentation
  drivers/gpu/drm/radeon/evergreen_cs.c: Remove unnecessary semicolon
  DRM/Radeon: On DVI-I use Load Detection when EDID is bogus.
  DRM/Radeon: Fix primary DAC Load Detection for RV100 chips.
  DRM/Radeon: Fix Load Detection on legacy primary DAC.
  drm: exynos: removed warning due to missing typecast for mixer driver data
  drm/exynos: add support for ARCH_MULTIPLATFORM
  MAINTAINERS: Add git repository for Exynos DRM
  drm/exynos: fix display on issue
  drm/i915: Only kick out vesafb if we takeover the fbcon with KMS
  drm/i915: be less verbose about inability to provide vendor backlight
  drm/i915: clear the entire sdvo infoframe buffer
  drm/i915: VGA needs to be on pipe A on i830M
  drm/i915: fix overlay on i830M