- 21 Jun, 2020 3 commits
-
-
Heiner Kallweit authored
Typically the firmware takes care that tp->ocp_base is reset to its default value. That's not the case (at least) for RTL8117. As a result subsequent PHY access reads/writes the wrong page and the link is broken. Fix this be resetting tp->ocp_base explicitly. Fixes: 229c1e0d ("r8169: load firmware for RTL8168fp/RTL8117") Reported-by:
Aaron Ma <mapengyu@gmail.com> Tested-by:
Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Dany Madden authored
Continue the reset path when partner adapter is not ready or H_CLOSED is returned from reset crq. This patch allows the CRQ init to proceed to establish a valid CRQ for traffic to flow after reset. Signed-off-by:
Dany Madden <drt@linux.ibm.com> Signed-off-by:
-
Shannon Nelson authored
Even with moving netif_tx_disable() to an earlier point when taking down the queues for a reconfiguration, we still end up with the occasional netdev watchdog Tx Timeout complaint. The old method of using netif_trans_update() works fine for queue 0, but has no effect on the remaining queues. Using netif_device_detach() allows us to signal to the watchdog to ignore us for the moment. Fixes: beead698 ("ionic: Add the basic NDO callbacks for netdev support") Signed-off-by:
Shannon Nelson <snelson@pensando.io> Acked-by:
Jonathan Toppins <jtoppins@redhat.com> Signed-off-by:
-
- 20 Jun, 2020 11 commits
-
-
Willem de Bruijn authored
The ETF qdisc can queue skbs that it could not pace on the errqueue. Address a few issues in the selftest - recv buffer size was too small, and incorrectly calculated - compared errno to ee_code instead of ee_errno - missed invalid request error type v2: - fix a few checkpatch --strict indentation warnings Fixes: ea6a5476 ("selftests/net: make so_txtime more robust to timer variance") Signed-off-by:
Willem de Bruijn <willemb@google.com> Signed-off-by:
-
Thomas Falcon authored
The max MTU limit defined for ibmveth is not accounting for virtual ethernet buffer overhead, which is twenty-two additional bytes set aside for the ethernet header and eight additional bytes of an opaque handle reserved for use by the hypervisor. Update the max MTU to reflect this overhead. Fixes: d894be57 ("ethernet: use net core MTU range checking in more drivers") Fixes: 110447f8 ("ethernet: fix min/max MTU typos") Signed-off-by:
Thomas Falcon <tlfalcon@linux.ibm.com> Signed-off-by:
-
David S. Miller authored
wenxu says: ==================== several fixes for indirect flow_blocks offload v2: patch2: store the cb_priv of representor to the flow_block_cb->indr.cb_priv in the driver. And make the correct check with the statments this->indr.cb_priv == cb_priv patch4: del the driver list only in the indriect cleanup callbacks v3: add the cover letter and changlogs. v4: collapsed 1/4, 2/4, 4/4 in v3 to one fix Add the prepare patch 1 and 2 v5: patch1: place flow_indr_block_cb_alloc() right before flow_indr_dev_setup_offload() to avoid moving flow_block_indr_init() This series fixes commit 1fac52da ("net: flow_offload: consolidate indirect flow_block infrastructure") that revists the flow_block infrastructure. patch #1 #2: prepare for fix patch #3 add and use flow_indr_block_cb_alloc/remove function patch #3: fix flow_indr_dev_unregister path If the representor is removed, then identify the indirect flow_blocks that need to be removed by the release callback and the port representor structure. To identify the port representor structure, a new indr.cb_priv field needs to be introduced. The flow_block also needs to be removed from the driver list from the cleanup path patch#4 fix block->nooffloaddevcnt warning dmesg log. When a indr device add in offload success. The block->nooffloaddevcnt should be 0. After the representor go away. When the dir device go away the flow_block UNBIND operation with -EOPNOTSUPP which lead the warning demesg log. The block->nooffloaddevcnt should always count for indr block. even the indr block offload successful. The representor maybe gone away and the ingress qdisc can work in software mode. ==================== Reviewed-by:
Simon Horman <simon.horman@netronome.com> Signed-off-by:
-
wenxu authored
The block->nooffloaddevcnt should always count for indr block. even the indr block offload successful. The representor maybe gone away and the ingress qdisc can work in software mode. block->nooffloaddevcnt warning with following dmesg log: [ 760.667058] ##################################################### [ 760.668186] ## TEST test-ecmp-add-vxlan-encap-disable-sriov.sh ## [ 760.669179] ##################################################### [ 761.780655] :test: Fedora 30 (Thirty) [ 761.783794] :test: Linux reg-r-vrt-018-180 5.7.0+ [ 761.822890] :test: NIC ens1f0 FW 16.26.6000 PCI 0000:81:00.0 DEVICE 0x1019 ConnectX-5 Ex [ 761.860244] mlx5_core 0000:81:00.0 ens1f0: Link up [ 761.880693] IPv6: ADDRCONF(NETDEV_CHANGE): ens1f0: link becomes ready [ 762.059732] mlx5_core 0000:81:00.1 ens1f1: Link up [ 762.234341] :test: unbind vfs of ens1f0 [ 762.257825] :test: Change ens1f0 eswitch (0000:81:00.0) mode to switchdev [ 762.291363] :test: unbind vfs of ens1f1 [ 762.306914] :test: Change ens1f1 eswitch (0000:81:00.1) mode to switchdev [ 762.309237] mlx5_core 0000:81:00.1: E-Switch: Disable: mode(LEGACY), nvfs(2), active vports(3) [ 763.282598] mlx5_core 0000:81:00.1: E-Switch: Supported tc offload range - chains: 4294967294, prios: 4294967295 [ 763.362825] mlx5_core 0000:81:00.1: MLX5E: StrdRq(1) RqSz(8) StrdSz(2048) RxCqeCmprss(0) [ 763.444465] mlx5_core 0000:81:00.1 ens1f1: renamed from eth0 [ 763.460088] mlx5_core 0000:81:00.1: MLX5E: StrdRq(1) RqSz(8) StrdSz(2048) RxCqeCmprss(0) [ 763.502586] mlx5_core 0000:81:00.1: MLX5E: StrdRq(1) RqSz(8) StrdSz(2048) RxCqeCmprss(0) [ 763.552429] ens1f1_0: renamed from eth0 [ 763.569569] mlx5_core 0000:81:00.1: E-Switch: Enable: mode(OFFLOADS), nvfs(2), active vports(3) [ 763.629694] ens1f1_1: renamed from eth1 [ 764.631552] IPv6: ADDRCONF(NETDEV_CHANGE): ens1f1_0: link becomes ready [ 764.670841] :test: unbind vfs of ens1f0 [ 764.681966] :test: unbind vfs of ens1f1 [ 764.726762] mlx5_core 0000:81:00.0 ens1f0: Link up [ 764.766511] mlx5_core 0000:81:00.1 ens1f1: Link up [ 764.797325] :test: Add multipath vxlan encap rule and disable sriov [ 764.798544] :test: config multipath route [ 764.812732] mlx5_core 0000:81:00.0: lag map port 1:2 port 2:2 [ 764.874556] mlx5_core 0000:81:00.0: modify lag map port 1:1 port 2:2 [ 765.603681] :test: OK [ 765.659048] IPv6: ADDRCONF(NETDEV_CHANGE): ens1f1_1: link becomes ready [ 765.675085] :test: verify rule in hw [ 765.694237] IPv6: ADDRCONF(NETDEV_CHANGE): ens1f0: link becomes ready [ 765.711892] IPv6: ADDRCONF(NETDEV_CHANGE): ens1f1: link becomes ready [ 766.979230] :test: OK [ 768.125419] :test: OK [ 768.127519] :test: - disable sriov ens1f1 [ 768.131160] pci 0000:81:02.2: Removing from iommu group 75 [ 768.132646] pci 0000:81:02.3: Removing from iommu group 76 [ 769.179749] mlx5_core 0000:81:00.1: E-Switch: Disable: mode(OFFLOADS), nvfs(2), active vports(3) [ 769.455627] mlx5_core 0000:81:00.0: modify lag map port 1:1 port 2:1 [ 769.703990] mlx5_core 0000:81:00.1: MLX5E: StrdRq(1) RqSz(8) StrdSz(2048) RxCqeCmprss(0) [ 769.988637] mlx5_core 0000:81:00.1 ens1f1: renamed from eth0 [ 769.990022] :test: - disable sriov ens1f0 [ 769.994922] pci 0000:81:00.2: Removing from iommu group 73 [ 769.997048] pci 0000:81:00.3: Removing from iommu group 74 [ 771.035813] mlx5_core 0000:81:00.0: E-Switch: Disable: mode(OFFLOADS), nvfs(2), active vports(3) [ 771.339091] ------------[ cut here ]------------ [ 771.340812] WARNING: CPU: 6 PID: 3448 at net/sched/cls_api.c:749 tcf_block_offload_unbind.isra.0+0x5c/0x60 [ 771.341728] Modules linked in: act_mirred act_tunnel_key cls_flower dummy vxlan ip6_udp_tunnel udp_tunnel sch_ingress nfsv3 nfs_acl nfs lockd grace fscache tun bridge stp llc sunrpc rdma_ucm rdma_cm iw_cm ib_cm mlx5_ib ib_uverbs ib_core mlx5_core intel_rapl_msr intel_rapl_common sb_edac x86_pkg_temp_thermal intel_powerclamp coretemp mlxfw act_ct nf_flow_table kvm_intel nf_nat kvm nf_conntrack irqbypass crct10dif_pclmul igb crc32_pclmul nf_defrag_ipv6 libcrc32c nf_defrag_ipv4 crc32c_intel ghash_clmulni_intel ptp ipmi_ssif intel_cstate pps_c ore ses intel_uncore mei_me iTCO_wdt joydev ipmi_si iTCO_vendor_support i2c_i801 enclosure mei ioatdma dca lpc_ich wmi ipmi_devintf pcspkr acpi_power_meter ipmi_msghandler acpi_pad ast i2c_algo_bit drm_vram_helper drm_kms_helper drm_ttm_helper ttm drm mpt3sas raid_class scsi_transport_sas [ 771.347818] CPU: 6 PID: 3448 Comm: test-ecmp-add-v Not tainted 5.7.0+ #1146 [ 771.348727] Hardware name: Supermicro SYS-2028TP-DECR/X10DRT-P, BIOS 2.0b 03/30/2017 [ 771.349646] RIP: 0010:tcf_block_offload_unbind.isra.0+0x5c/0x60 [ 771.350553] Code: 4a fd ff ff 83 f8 a1 74 0e 5b 4c 89 e7 5d 41 5c 41 5d e9 07 93 89 ff 8b 83 a0 00 00 00 8d 50 ff 89 93 a0 00 00 00 85 c0 75 df <0f> 0b eb db 0f 1f 44 00 00 41 57 41 56 41 55 41 89 cd 41 54 49 89 [ 771.352420] RSP: 0018:ffffb33144cd3b00 EFLAGS: 00010246 [ 771.353353] RAX: 0000000000000000 RBX: ffff8b37cf4b2800 RCX: 0000000000000000 [ 771.354294] RDX: 00000000ffffffff RSI: ffff8b3b9aad0000 RDI: ffffffff8d5c6e20 [ 771.355245] RBP: ffff8b37eb546948 R08: ffffffffc0b7a348 R09: ffff8b3b9aad0000 [ 771.356189] R10: 0000000000000001 R11: ffff8b3ba7a0a1c0 R12: ffff8b37cf4b2850 [ 771.357123] R13: ffff8b3b9aad0000 R14: ffff8b37cf4b2820 R15: ffff8b37cf4b2820 [ 771.358039] FS: 00007f8a19b6e740(0000) GS:ffff8b3befa00000(0000) knlGS:0000000000000000 [ 771.358965] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 771.359885] CR2: 00007f3afb91c1a0 CR3: 000000045133c004 CR4: 00000000001606e0 [ 771.360825] Call Trace: [ 771.361764] __tcf_block_put+0x84/0x150 [ 771.362712] ingress_destroy+0x1b/0x20 [sch_ingress] [ 771.363658] qdisc_destroy+0x3e/0xc0 [ 771.364594] dev_shutdown+0x7a/0xa5 [ 771.365522] rollback_registered_many+0x20d/0x530 [ 771.366458] ? netdev_upper_dev_unlink+0x15d/0x1c0 [ 771.367387] unregister_netdevice_many.part.0+0xf/0x70 [ 771.368310] vxlan_netdevice_event+0xa4/0x110 [vxlan] [ 771.369454] notifier_call_chain+0x4c/0x70 [ 771.370579] rollback_registered_many+0x2f5/0x530 [ 771.371719] rollback_registered+0x56/0x90 [ 771.372843] unregister_netdevice_queue+0x73/0xb0 [ 771.373982] unregister_netdev+0x18/0x20 [ 771.375168] mlx5e_vport_rep_unload+0x56/0xc0 [mlx5_core] [ 771.376327] esw_offloads_disable+0x81/0x90 [mlx5_core] [ 771.377512] mlx5_eswitch_disable_locked.cold+0xcb/0x1af [mlx5_core] [ 771.378679] mlx5_eswitch_disable+0x44/0x60 [mlx5_core] [ 771.379822] mlx5_device_disable_sriov+0xad/0xb0 [mlx5_core] [ 771.380968] mlx5_core_sriov_configure+0xc1/0xe0 [mlx5_core] [ 771.382087] sriov_numvfs_store+0xfc/0x130 [ 771.383195] kernfs_fop_write+0xce/0x1b0 [ 771.384302] vfs_write+0xb6/0x1a0 [ 771.385410] ksys_write+0x5f/0xe0 [ 771.386500] do_syscall_64+0x5b/0x1d0 [ 771.387569] entry_SYSCALL_64_after_hwframe+0x44/0xa9 Fixes: 0fdcf78d ("net: use flow_indr_dev_setup_offload()") Signed-off-by:
wenxu <wenxu@ucloud.cn> Signed-off-by:
-
wenxu authored
If the representor is removed, then identify the indirect flow_blocks that need to be removed by the release callback and the port representor structure. To identify the port representor structure, a new indr.cb_priv field needs to be introduced. The flow_block also needs to be removed from the driver list from the cleanup path. Fixes: 1fac52da ("net: flow_offload: consolidate indirect flow_block infrastructure") Signed-off-by:
-
wenxu authored
Prepare fix the bug in the next patch. use flow_indr_block_cb_alloc/remove function and remove the __flow_block_indr_binding. Signed-off-by:
-
wenxu authored
Add flow_indr_block_cb_alloc/remove function for next fix patch. Signed-off-by:
-
Sabrina Dubroca authored
Currently, trying to change the DF parameter of a geneve device does nothing: # ip -d link show geneve1 14: geneve1: <snip> link/ether <snip> geneve id 1 remote 10.0.0.1 ttl auto df set dstport 6081 <snip> # ip link set geneve1 type geneve id 1 df unset # ip -d link show geneve1 14: geneve1: <snip> link/ether <snip> geneve id 1 remote 10.0.0.1 ttl auto df set dstport 6081 <snip> We just need to update the value in geneve_changelink. Fixes: a025fb5f ("geneve: Allow configuration of DF behaviour") Signed-off-by:Sabrina Dubroca <sd@queasysnail.net> Reviewed-by:
Stefano Brivio <sbrivio@redhat.com> Signed-off-by:
-
Claudiu Manoil authored
VLAN tag insertion/extraction offload is correctly activated at probe time but deactivation of this feature (i.e. via ethtool) is broken. Toggling works only for Tx/Rx ring 0 of a PF, and is ignored for the other rings, including the VF rings. To fix this, the existing VLAN offload toggling code was extended to all the rings assigned to a netdevice, instead of the default ring 0 (likely a leftover from the early validation days of this feature). And the code was moved to the common set_features() function to fix toggling for the VF driver too. Fixes: d4fd0404 ("enetc: Introduce basic PF and VF ENETC ethernet drivers") Signed-off-by:
Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by:
-
Claudiu Beznea authored
Undo previously done operation in case macb_phylink_connect() fails. Since macb_reset_hw() is the 1st undo operation the napi_exit label was renamed to reset_hw. Fixes: 7897b071 ("net: macb: convert to phylink") Signed-off-by:
Claudiu Beznea <claudiu.beznea@microchip.com> Acked-by:
Nicolas Ferre <nicolas.ferre@microchip.com> Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fsDavid S. Miller authored
David Howells says: ==================== rxrpc: Performance drop fix and other fixes Here are three fixes for rxrpc: (1) Fix a trace symbol mapping. It doesn't seem to let you map to "". (2) Fix the handling of the remote receive window size when it increases beyond the size we can support for our transmit window. (3) Fix a performance drop caused by retransmitted packets being accidentally marked as already ACK'd. ==================== Signed-off-by:
-
- 19 Jun, 2020 26 commits
-
-
David S. Miller authored
Florian Fainelli says: ==================== net: phy: MDIO bus scanning fixes This patch series fixes two problems with the current MDIO bus scanning logic which was identified while moving from 4.9 to 5.4 on devices that do rely on scanning the MDIO bus at runtime because they use pluggable cards. Changes in v2: - added comment explaining the special value of -ENODEV - added Andrew's Reviewed-by tag ==================== Signed-off-by: -
Florian Fainelli authored
Commit 02a6efca ("net: phy: allow scanning busses with missing phys") added a special condition to return -ENODEV in case -ENODEV or -EIO was returned from the first read of the MII_PHYSID1 register. In case the MDIO bus data line pull-up is not strong enough, the MDIO bus controller will not flag this as a read error. This can happen when a pluggable daughter card is not connected and weak internal pull-ups are used (since that is the only option, otherwise the pins are floating). The second read of MII_PHYSID2 will be correctly flagged an error though, but now we will return -EIO which will be treated as a hard error, thus preventing MDIO bus scanning loops to continue succesfully. Apply the same logic to both register reads, thus allowing the scanning logic to proceed. Fixes: 02a6efca ("net: phy: allow scanning busses with missing phys") Reviewed-by:
Andrew Lunn <andrew@lunn.ch> Signed-off-by:
Florian Fainelli <f.fainelli@gmail.com> Signed-off-by:
-
Florian Fainelli authored
Commit 209c65b6 ("drivers/of/of_mdio.c:fix of_mdiobus_register()") introduced a break of the loop on the premise that a successful registration should exit the loop. The premise is correct but not to code, because rc && rc != -ENODEV is just a special error condition, that means we would exit the loop even with rc == -ENODEV which is absolutely not correct since this is the error code to indicate to the MDIO bus layer that scanning should continue. Fix this by explicitly checking for rc = 0 as the only valid condition to break out of the loop. Fixes: 209c65b6 ("drivers/of/of_mdio.c:fix of_mdiobus_register()") Reviewed-by:
-
Flavio Suligoi authored
Fix typo: "Triger" --> "Trigger" Signed-off-by:
Flavio Suligoi <f.suligoi@asem.it> Signed-off-by:
-
Flavio Suligoi authored
Fix typo: "trigered" --> "triggered" Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/klassert/ipsecDavid S. Miller authored
Steffen Klassert says: ==================== pull request (net): ipsec 2020-06-19 1) Fix double ESP trailer insertion in IPsec crypto offload if netif_xmit_frozen_or_stopped is true. From Huy Nguyen. 2) Merge fixup for "remove output_finish indirection from xfrm_state_afinfo". From Stephen Rothwell. 3) Select CRYPTO_SEQIV for ESP as this is needed for GCM and several other encryption algorithms. Also modernize the crypto algorithm selections for ESP and AH, remove those that are maked as "MUST NOT" and add those that are marked as "MUST" be implemented in RFC 8221. From Eric Biggers. Please note the merge conflict between commit: a7f7f624 ("treewide: replace '---help---' in Kconfig files with 'help'") from Linus' tree and commits: 7d4e3919 ("esp, ah: consolidate the crypto algorithm selections") be013698 ("esp, ah: modernize the crypto algorithm selections") from the ipsec tree. ==================== Signed-off-by:
-
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queueDavid S. Miller authored
Jeff Kirsher says: ==================== Intel Wired LAN Driver Updates 2020-06-18 This series contains fixes to ixgbe, i40e and ice driver. Ciara fixes up the ixgbe, i40e and ice drivers to protect access when allocating and freeing the rings. In addition, made use of READ_ONCE when reading the rings prior to accessing the statistics pointer. Björn fixes a crash where the receive descriptor ring allocation was moved to a different function, which broke the ethtool set_ringparam() hook. ==================== Signed-off-by: -
Björn Töpel authored
When the AF_XDP buffer allocator was introduced, the Rx SW ring "rx_bi" allocation was moved from i40e_setup_rx_descriptors() function, and was instead done in the i40e_configure_rx_ring() function. This broke the ethtool set_ringparam() hook for changing the Rx descriptor count, which was relying on i40e_setup_rx_descriptors() to handle the allocation. Fix this by adding an explicit i40e_alloc_rx_bi() call to i40e_set_ringparam(). Fixes: be1222b5 ("i40e: Separate kernel allocated rx_bi rings from AF_XDP rings") Signed-off-by:
Björn Töpel <bjorn.topel@intel.com> Tested-by:
Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by:
Jeff Kirsher <jeffrey.t.kirsher@intel.com>
-
Ciara Loftus authored
The READ_ONCE macro is used when reading rings prior to accessing the statistics pointer. The corresponding WRITE_ONCE usage when allocating and freeing the rings to ensure protected access was not in place. Introduce this. Signed-off-by:
Ciara Loftus <ciara.loftus@intel.com> Tested-by:
-
Ciara Loftus authored
READ_ONCE should be used when reading rings prior to accessing the statistics pointer. Introduce this as well as the corresponding WRITE_ONCE usage when allocating and freeing the rings, to ensure protected access. Signed-off-by:
-
Ciara Loftus authored
READ_ONCE should be used when reading rings prior to accessing the statistics pointer. Introduce this as well as the corresponding WRITE_ONCE usage when allocating and freeing the rings, to ensure protected access. Signed-off-by:
-
Eric Dumazet authored
Back in commit f60e5990 ("ipv6: protect skb->sk accesses from recursive dereference inside the stack") Hannes added code so that IPv6 stack would not trust skb->sk for typical cases where packet goes through 'standard' xmit path (__dev_queue_xmit()) Alas af_packet had a dev_direct_xmit() path that was not dealing yet with xmit_recursion level. Also change sk_mc_loop() to dump a stack once only. Without this patch, syzbot was able to trigger : [1] [ 153.567378] WARNING: CPU: 7 PID: 11273 at net/core/sock.c:721 sk_mc_loop+0x51/0x70 [ 153.567378] Modules linked in: nfnetlink ip6table_raw ip6table_filter iptable_raw iptable_nat nf_nat nf_conntrack nf_defrag_ipv4 nf_defrag_ipv6 iptable_filter macsec macvtap tap macvlan 8021q hsr wireguard libblake2s blake2s_x86_64 libblake2s_generic udp_tunnel ip6_udp_tunnel libchacha20poly1305 poly1305_x86_64 chacha_x86_64 libchacha curve25519_x86_64 libcurve25519_generic netdevsim batman_adv dummy team bridge stp llc w1_therm wire i2c_mux_pca954x i2c_mux cdc_acm ehci_pci ehci_hcd mlx4_en mlx4_ib ib_uverbs ib_core mlx4_core [ 153.567386] CPU: 7 PID: 11273 Comm: b159172088 Not tainted 5.8.0-smp-DEV #273 [ 153.567387] RIP: 0010:sk_mc_loop+0x51/0x70 [ 153.567388] Code: 66 83 f8 0a 75 24 0f b6 4f 12 b8 01 00 00 00 31 d2 d3 e0 a9 bf ef ff ff 74 07 48 8b 97 f0 02 00 00 0f b6 42 3a 83 e0 01 5d c3 <0f> 0b b8 01 00 00 00 5d c3 0f b6 87 18 03 00 00 5d c0 e8 04 83 e0 [ 153.567388] RSP: 0018:ffff95c69bb93990 EFLAGS: 00010212 [ 153.567388] RAX: 0000000000000011 RBX: ffff95c6e0ee3e00 RCX: 0000000000000007 [ 153.567389] RDX: ffff95c69ae50000 RSI: ffff95c6c30c3000 RDI: ffff95c6c30c3000 [ 153.567389] RBP: ffff95c69bb93990 R08: ffff95c69a77f000 R09: 0000000000000008 [ 153.567389] R10: 0000000000000040 R11: 00003e0e00026128 R12: ffff95c6c30c3000 [ 153.567390] R13: ffff95c6cc4fd500 R14: ffff95c6f84500c0 R15: ffff95c69aa13c00 [ 153.567390] FS: 00007fdc3a283700(0000) GS:ffff95c6ff9c0000(0000) knlGS:0000000000000000 [ 153.567390] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 153.567391] CR2: 00007ffee758e890 CR3: 0000001f9ba20003 CR4: 00000000001606e0 [ 153.567391] Call Trace: [ 153.567391] ip6_finish_output2+0x34e/0x550 [ 153.567391] __ip6_finish_output+0xe7/0x110 [ 153.567391] ip6_finish_output+0x2d/0xb0 [ 153.567392] ip6_output+0x77/0x120 [ 153.567392] ? __ip6_finish_output+0x110/0x110 [ 153.567392] ip6_local_out+0x3d/0x50 [ 153.567392] ipvlan_queue_xmit+0x56c/0x5e0 [ 153.567393] ? ksize+0x19/0x30 [ 153.567393] ipvlan_start_xmit+0x18/0x50 [ 153.567393] dev_direct_xmit+0xf3/0x1c0 [ 153.567393] packet_direct_xmit+0x69/0xa0 [ 153.567394] packet_sendmsg+0xbf0/0x19b0 [ 153.567394] ? plist_del+0x62/0xb0 [ 153.567394] sock_sendmsg+0x65/0x70 [ 153.567394] sock_write_iter+0x93/0xf0 [ 153.567394] new_sync_write+0x18e/0x1a0 [ 153.567395] __vfs_write+0x29/0x40 [ 153.567395] vfs_write+0xb9/0x1b0 [ 153.567395] ksys_write+0xb1/0xe0 [ 153.567395] __x64_sys_write+0x1a/0x20 [ 153.567395] do_syscall_64+0x43/0x70 [ 153.567396] entry_SYSCALL_64_after_hwframe+0x44/0xa9 [ 153.567396] RIP: 0033:0x453549 [ 153.567396] Code: Bad RIP value. [ 153.567396] RSP: 002b:00007fdc3a282cc8 EFLAGS: 00000246 ORIG_RAX: 0000000000000001 [ 153.567397] RAX: ffffffffffffffda RBX: 00000000004d32d0 RCX: 0000000000453549 [ 153.567397] RDX: 0000000000000020 RSI: 0000000020000300 RDI: 0000000000000003 [ 153.567398] RBP: 00000000004d32d8 R08: 0000000000000000 R09: 0000000000000000 [ 153.567398] R10: 0000000000000000 R11: 0000000000000246 R12: 00000000004d32dc [ 153.567398] R13: 00007ffee742260f R14: 00007fdc3a282dc0 R15: 00007fdc3a283700 [ 153.567399] ---[ end trace c1d5ae2b1059ec62 ]--- f60e5990 ("ipv6: protect skb->sk accesses from recursive dereference inside the stack") Signed-off-by:
Eric Dumazet <edumazet@google.com> Reported-by:
syzbot <syzkaller@googlegroups.com> Signed-off-by:
-
Florian Fainelli authored
of_find_node_by_name() will do an of_node_put() on the "from" argument. With CONFIG_OF_DYNAMIC enabled which checks for device_node reference counts, we would be getting a warning like this: [ 6.347230] refcount_t: increment on 0; use-after-free. [ 6.352498] WARNING: CPU: 3 PID: 77 at lib/refcount.c:156 refcount_inc_checked+0x38/0x44 [ 6.360601] Modules linked in: [ 6.363661] CPU: 3 PID: 77 Comm: kworker/3:1 Tainted: G W 5.4.46-gb78b3e9956e6 #13 [ 6.372546] Hardware name: BCM97278SV (DT) [ 6.376649] Workqueue: events deferred_probe_work_func [ 6.381796] pstate: 60000005 (nZCv daif -PAN -UAO) [ 6.386595] pc : refcount_inc_checked+0x38/0x44 [ 6.391133] lr : refcount_inc_checked+0x38/0x44 ... [ 6.478791] Call trace: [ 6.481243] refcount_inc_checked+0x38/0x44 [ 6.485433] kobject_get+0x3c/0x4c [ 6.488840] of_node_get+0x24/0x34 [ 6.492247] of_irq_find_parent+0x3c/0xe0 [ 6.496263] of_irq_parse_one+0xe4/0x1d0 [ 6.500191] irq_of_parse_and_map+0x44/0x84 [ 6.504381] bcm_sf2_sw_probe+0x22c/0x844 [ 6.508397] platform_drv_probe+0x58/0xa8 [ 6.512413] really_probe+0x238/0x3fc [ 6.516081] driver_probe_device+0x11c/0x12c [ 6.520358] __device_attach_driver+0xa8/0x100 [ 6.524808] bus_for_each_drv+0xb4/0xd0 [ 6.528650] __device_attach+0xd0/0x164 [ 6.532493] device_initial_probe+0x24/0x30 [ 6.536682] bus_probe_device+0x38/0x98 [ 6.540524] deferred_probe_work_func+0xa8/0xd4 [ 6.545061] process_one_work+0x178/0x288 [ 6.549078] process_scheduled_works+0x44/0x48 [ 6.553529] worker_thread+0x218/0x270 [ 6.557285] kthread+0xdc/0xe4 [ 6.560344] ret_from_fork+0x10/0x18 [ 6.563925] ---[ end trace 68f65caf69bb152a ]--- Fix this by adding a of_node_get() to increment the reference count prior to the call. Fixes: afa3b592 ("net: dsa: bcm_sf2: Ensure correct sub-node is parsed") Signed-off-by:
-
Alexander Lobakin authored
Commit 3b335832 ("net: Add fraglist GRO/GSO feature flags") missed an entry for NETIF_F_GSO_FRAGLIST in netdev_features_strings array. As a result, fraglist GSO feature is not shown in 'ethtool -k' output and can't be toggled on/off. The fix is trivial. Fixes: 3b335832 ("net: Add fraglist GRO/GSO feature flags") Signed-off-by:
Alexander Lobakin <alobakin@pm.me> Reviewed-by:
Michal Kubecek <mkubecek@suse.cz> Signed-off-by:
-
David Christensen authored
The driver function tg3_io_error_detected() calls napi_disable twice, without an intervening napi_enable, when the number of EEH errors exceeds eeh_max_freezes, resulting in an indefinite sleep while holding rtnl_lock. Add check for pcierr_recovery which skips code already executed for the "Frozen" state. Signed-off-by:
David Christensen <drc@linux.vnet.ibm.com> Reviewed-by:
Michael Chan <michael.chan@broadcom.com> Signed-off-by:
-
Martin authored
Code to handle multiproto configuration is missing. Fixes: 4b5f6723 ("net: Special handling for IP & MPLS") Signed-off-by:
Martin <martin.varghese@nokia.com> Signed-off-by:
-
David S. Miller authored
Julian Wiedmann says: ==================== s390/qeth: fixes 2020-06-17 please apply the following patch series for qeth to netdev's net tree. The first patch fixes a regression in the error handling for a specific cmd type. I have some follow-ups queued up for net-next to clean this up properly... The second patch fine-tunes the HW offload restrictions that went in with this merge window. In some setups we don't need to apply them. ==================== Signed-off-by: -
Julian Wiedmann authored
When a device is configured with ISOLATION_MODE_FWD, traffic never goes through the internal switch. Don't apply the offload restrictions in this case. Fixes: c619e9a6 ("s390/qeth: don't use restricted offloads for local traffic") Signed-off-by:
Julian Wiedmann <jwi@linux.ibm.com> Signed-off-by:
-
Julian Wiedmann authored
Current(?) OSA devices also store their cmd-specific return codes for SET_ACCESS_CONTROL cmds into the top-level cmd->hdr.return_code. So once we added stricter checking for the top-level field a while ago, none of the error logic that rolls back the user's configuration to its old state is applied any longer. For this specific cmd, go back to the old model where we peek into the cmd structure even though the top-level field indicated an error. Fixes: 686c97ee ("s390/qeth: fix error handling in adapter command callbacks") Signed-off-by:
-
David S. Miller authored
Paolo Abeni says: ==================== mptcp: cope with syncookie on MP_JOINs Currently syncookies on MP_JOIN connections are not handled correctly: the connections fallback to TCP and are kept alive instead of resetting them at fallback time. The first patch propagates the required information up to syn_recv_sock time, and the 2nd patch addresses the unifying the error path for all MP_JOIN requests. ==================== Signed-off-by: -
Paolo Abeni authored
Currently any MPTCP socket using syn cookies will fallback to TCP at 3rd ack time. In case of MP_JOIN requests, the RFC mandate closing the child and sockets, but the existing error paths do not handle the syncookie scenario correctly. Address the issue always forcing the child shutdown in case of MP_JOIN fallback. Fixes: ae2dd716 ("mptcp: handle tcp fallback when using syn cookies") Signed-off-by:
Paolo Abeni <pabeni@redhat.com> Reviewed-by:
Mat Martineau <mathew.j.martineau@linux.intel.com> Signed-off-by:
-
Paolo Abeni authored
The msk ownership is transferred to the child socket at 3rd ack time, so that we avoid more lookups later. If the request does not reach the 3rd ack, the MSK reference is dropped at request sock release time. As a side effect, fallback is now tracked by a NULL msk reference instead of zeroed 'mp_join' field. This will simplify the next patch. Signed-off-by:
-
guodeqing authored
ie., $ ifconfig eth0 6.6.6.6 netmask 255.255.255.0 $ ip rule add from 6.6.6.6 table 6666 $ ip route add 9.9.9.9 via 6.6.6.6 $ ping -I 6.6.6.6 9.9.9.9 PING 9.9.9.9 (9.9.9.9) from 6.6.6.6 : 56(84) bytes of data. 3 packets transmitted, 0 received, 100% packet loss, time 2079ms $ arp Address HWtype HWaddress Flags Mask Iface 6.6.6.6 (incomplete) eth0 The arp request address is error, this is because fib_table_lookup in fib_check_nh lookup the destnation 9.9.9.9 nexthop, the scope of the fib result is RT_SCOPE_LINK,the correct scope is RT_SCOPE_HOST. Here I add a check of whether this is RT_TABLE_MAIN to solve this problem. Fixes: 3bfd8472 ("net: Use passed in table for nexthop lookups") Signed-off-by:
guodeqing <geffrey.guo@huawei.com> Reviewed-by:
David Ahern <dsahern@gmail.com> Signed-off-by:
-
David S. Miller authored
Vladimir Oltean says: ==================== Fix VLAN checks for SJA1105 DSA tc-flower filters This fixes a ridiculous situation where the driver, in VLAN-unaware mode, would refuse accepting any tc filter: tc filter replace dev sw1p3 ingress flower skip_sw \ dst_mac 42:be:24:9b:76:20 \ action gate (...) Error: sja1105: Can only gate based on {DMAC, VID, PCP}. tc filter replace dev sw1p3 ingress protocol 802.1Q flower skip_sw \ vlan_id 1 vlan_prio 0 dst_mac 42:be:24:9b:76:20 \ action gate (...) Error: sja1105: Can only gate based on DMAC. So, without changing the VLAN awareness state, it says it doesn't want VLAN-aware rules, and it doesn't want VLAN-unaware rules either. One would say it's in Schrodinger's state... Now, the situation has been made worse by commit 7f14937f ("net: dsa: sja1105: keep the VLAN awareness state in a driver variable"), which made VLAN awareness a ternary attribute, but after inspecting the code from before that patch with a truth table, it looks like the logical bug was there even before. While attempting to fix this, I also noticed some leftover debugging code in one of the places that needed to be fixed. It would have appeared in the context of patch 3/3 anyway, so I decided to create a patch that removes it. ==================== Signed-off-by: -
Vladimir Oltean authored
This action requires the VLAN awareness state of the switch to be of the same type as the key that's being added: - If the switch is unaware of VLAN, then the tc filter key must only contain the destination MAC address. - If the switch is VLAN-aware, the key must also contain the VLAN ID and PCP. But this check doesn't work unless we verify the VLAN awareness state on both the "if" and the "else" branches. Fixes: 834f8933 ("net: dsa: sja1105: implement tc-gate using time-triggered virtual links") Signed-off-by:
Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by:
-
Vladimir Oltean authored
This action requires the VLAN awareness state of the switch to be of the same type as the key that's being added: - If the switch is unaware of VLAN, then the tc filter key must only contain the destination MAC address. - If the switch is VLAN-aware, the key must also contain the VLAN ID and PCP. But this check doesn't work unless we verify the VLAN awareness state on both the "if" and the "else" branches. Fixes: dfacc5a2 ("net: dsa: sja1105: support flow-based redirection via virtual links") Signed-off-by:
-
