- 12 Dec, 2022 40 commits
-
-
Sven Peter authored
Broadcom BCM4377/4378/4387 are dual WiFi/Bluetooth boards found in Apple machines. This driver adds support for the Bluetooth function which exposes a shared memory IPC protocol over PCIe to tunnel HCI traffic. Signed-off-by:
Sven Peter <sven@svenpeter.dev> Signed-off-by:
Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
-
Sven Peter authored
Broadcom 4378/4387 controllers found in Apple Silicon Macs claim to support getting MWS Transport Layer Configuration, < HCI Command: Read Local Supported... (0x04|0x0002) plen 0 > HCI Event: Command Complete (0x0e) plen 68 Read Local Supported Commands (0x04|0x0002) ncmd 1 Status: Success (0x00) [...] Get MWS Transport Layer Configuration (Octet 30 - Bit 3)] [...] , but then don't actually allow the required command: > HCI Event: Command Complete (0x0e) plen 15 Get MWS Transport Layer Configuration (0x05|0x000c) ncmd 1 Status: Command Disallowed (0x0c) Number of transports: 0 Baud rate list: 0 entries 00 00 00 00 00 00 00 00 00 00 Signed-off-by: -
Sven Peter authored
Broadcom 4377 controllers found in Apple x86 Macs with the T2 chip claim to support extended scanning when querying supported states, < HCI Command: LE Read Supported St.. (0x08|0x001c) plen 0 > HCI Event: Command Complete (0x0e) plen 12 LE Read Supported States (0x08|0x001c) ncmd 1 Status: Success (0x00) States: 0x000003ffffffffff [...] LE Set Extended Scan Parameters (Octet 37 - Bit 5) LE Set Extended Scan Enable (Octet 37 - Bit 6) [...] , but then fail to actually implement the extended scanning: < HCI Command: LE Set Extended Sca.. (0x08|0x0041) plen 8 Own address type: Random (0x01) Filter policy: Accept all advertisement (0x00) PHYs: 0x01 Entry 0: LE 1M Type: Active (0x01) Interval: 11.250 msec (0x0012) Window: 11.250 msec (0x0012) > HCI Event: Command Complete (0x0e) plen 4 LE Set Extended Scan Parameters (0x08|0x0041) ncmd 1 Status: Unknown HCI Command (0x01) Signed-off-by: -
Sven Peter authored
Broadcom controllers present on Apple Silicon devices use the upper 8 bits of the event type in the LE Extended Advertising Report for the channel on which the frame has been received. These bits are reserved according to the Bluetooth spec anyway such that we can just drop them to ensure that the advertising results are parsed correctly. The following excerpt from a btmon trace shows a report received on channel 37 by these controllers: > HCI Event: LE Meta Event (0x3e) plen 55 LE Extended Advertising Report (0x0d) Num reports: 1 Entry 0 Event type: 0x2513 Props: 0x0013 Connectable Scannable Use legacy advertising PDUs Data status: Complete Reserved (0x2500) Legacy PDU Type: Reserved (0x2513) Address type: Public (0x00) Address: XX:XX:XX:XX:XX:XX (Shenzhen Jingxun Software [...]) Primary PHY: LE 1M Secondary PHY: No packets SID: no ADI field (0xff) TX power: 127 dBm RSSI: -76 dBm (0xb4) Periodic advertising interval: 0.00 msec (0x0000) Direct address type: Public (0x00) Direct address: 00:00:00:00:00:00 (OUI 00-00-00) Data length: 0x1d [...] Flags: 0x18 Simultaneous LE and BR/EDR (Controller) Simultaneous LE and BR/EDR (Host) Company: Harman International Industries, Inc. (87) Data: [...] Service Data (UUID 0xfddf): Name (complete): JBL Flip 5 Signed-off-by: -
Sven Peter authored
Add bluetooth controller nodes and the required brcm,board-type properties to be able to select the correct firmware to all board device trees. Signed-off-by:
-
Sven Peter authored
These chips are combined Wi-Fi/Bluetooth radios which expose a PCI subfunction for the Bluetooth part. They are found in Apple machines such as the x86 models with the T2 chip or the arm64 models with the M1 or M2 chips. Signed-off-by:
Rob Herring <robh@kernel.org> Signed-off-by:
-
Sven Peter authored
Bluetooth controllers share the common local-bd-address property. Add a generic YAML schema to replace bluetooth.txt for those. Signed-off-by:
-
Marek Vasut authored
CYW4373A0 is a Wi-Fi + Bluetooth combo device from Cypress. This chip is present e.g. on muRata 2AE module. This chip has additional quirk where the HCI command 0xfc45, used on older chips to switch UART clock from 24 MHz to 48 MHz, to support baudrates over 3 Mbdps, is no longer recognized by this newer chip. This newer chip can configure the 4 Mbdps baudrate without the need to issue HCI command 0xfc45, so add flag to indicate this and do not issue the command on this chip to avoid failure to set 4 Mbdps baud rate. It is not clear whether there is a way to determine which chip does and which chip does not support the HCI command 0xfc45, other than trial and error. Reviewed-by:
Linus Walleij <linus.walleij@linaro.org> Signed-off-by:
Marek Vasut <marex@denx.de> Signed-off-by:
-
Marek Vasut authored
CYW4373A0 is a Wi-Fi + Bluetooth combo device from Cypress. This chip is present e.g. on muRata 2AE module. Extend the binding with its DT compatible. Acked-by:
-
Kang Minchul authored
Replace kmalloc+memset by kzalloc for better readability and simplicity. This addresses the cocci warning below: WARNING: kzalloc should be used for d, instead of kmalloc/memset Signed-off-by:
Kang Minchul <tegongkang@gmail.com> Signed-off-by:
-
Shengyu Qu authored
Add IDs to usb_device_id table for WCN6855. IDs are extracted from Windows driver of Lenovo Thinkpad T14 Gen 2(Driver version 1.0.0.1205 Windows 10) Windows driver download address: https://pcsupport.lenovo.com/us/en/products/laptops-and-netbooks/ thinkpad-t-series-laptops/thinkpad-t14-gen-2-type-20xk-20xl/downloads /driver-list/ Signed-off-by:
Shengyu Qu <wiagn233@outlook.com> Signed-off-by:
-
Christophe JAILLET authored
'err' is known to be <0 at this point. So, some cases can not be reached because of a missing "-". Add it. Fixes: ca2045e0 ("Bluetooth: Add bt_status") Signed-off-by:
Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by:
-
Luiz Augusto von Dentz authored
This adds CONFIG_BT_LE_L2CAP_ECRED which can be used to enable L2CAP Enhanced Credit Flow Control Mode by default, previously it was only possible to set it via module parameter (e.g. bluetooth.enable_ecred=1). Since L2CAP ECRED mode is required by the likes of EATT which is recommended for LE Audio this enables it by default. Signed-off-by:
Tedd Ho-Jeong An <tedd.an@intel.com>
-
Luiz Augusto von Dentz authored
poll_sync has been proven to fix races of USB data and event endpoints so this enables it by default. Signed-off-by:
-
Luiz Augusto von Dentz authored
This adds CONFIG_BT_HCIBTUSB_POLL_SYNC which can be used to set the default behavior of Bluetooth USB controller with respect to poll synchronization of its endpoits. Signed-off-by:
-
Igor Skalkin authored
The current version of the configuration structure has unaligned 16-bit fields, but according to the specification [1], access to the configuration space must be aligned. Add a second, aligned version of the configuration structure and a new feature bit indicating that this version is being used. [1] https://docs.oasis-open.org/virtio/virtio/v1.1/virtio-v1.1.pdfSigned-off-by:
Igor Skalkin <Igor.Skalkin@opensynergy.com> Signed-off-by:
-
Inga Stotland authored
When validating the parameter length for MGMT_OP_ADD_EXT_ADV_PARAMS command, use the correct op code in error status report: was MGMT_OP_ADD_ADVERTISING, changed to MGMT_OP_ADD_EXT_ADV_PARAMS. Fixes: 12410572 ("Bluetooth: Break add adv into two mgmt commands") Signed-off-by:
Inga Stotland <inga.stotland@intel.com> Signed-off-by:
-
Yang Yingliang authored
If hci_register_suspend_notifier() returns error, the hdev and rfkill are leaked. We could disregard the error and print a warning message instead to avoid leaks, as it just means we won't be handing suspend requests. Fixes: 9952d90e ("Bluetooth: Handle PM_SUSPEND_PREPARE and PM_POST_SUSPEND") Signed-off-by:
Yang Yingliang <yangyingliang@huawei.com> Signed-off-by:
-
Jiapeng Chong authored
Use kzalloc rather than duplicating its implementation, which makes code simple and easy to understand. ./net/bluetooth/hci_conn.c:2038:6-13: WARNING: kzalloc should be used for cp, instead of kmalloc/memset. Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=2406Reported-by:
Abaci Robot <abaci@linux.alibaba.com> Signed-off-by:
Jiapeng Chong <jiapeng.chong@linux.alibaba.com> Signed-off-by:
-
Zhengping Jiang authored
Only assign hdev->wakeup if the serial port supports wakeup. Otherwise it will fall back to the hci_uart_wakeup or the behavior that can be overridden before calling the hci_uart_register_device(). Signed-off-by:
Zhengping Jiang <jiangzp@google.com> Signed-off-by:
-
Pauli Virtanen authored
For ISO BIS related functions in hci_conn.c, make dst_type values be HCI address type values, not ISO socket address type values. This makes it consistent with CIS functions. Signed-off-by:
Pauli Virtanen <pav@iki.fi> Signed-off-by:
-
Hilda Wu authored
For USB ALT 6 settings some Realtek chips need to transmit mSBC data continuously without the zero length of USB packets. In this commit, create BTUSB_ALT6_CONTINUOUS_TX to manage the behavior. Therefore, create REALTEK_ALT6_CONTINUOUS_TX_CHIP to manage the specific chip model for the behavior. Signed-off-by:
Max Chou <max.chou@realtek.com> Signed-off-by:
Hilda Wu <hildawu@realtek.com> Signed-off-by:
-
Hilda Wu authored
This patch adds a data structure for btrealtek object, and the definition of vendor behavior flags. It also adds macros to set/test/get the flags. Signed-off-by:
-
Michael S. Tsirkin authored
Device removal is clearly out of virtio spec: it attempts to remove unused buffers from a VQ before invoking device reset. To fix, make open/close NOPs and do all cleanup/setup in probe/remove. NB: This is a hacky way to handle this - virtbt_{open,close} as NOP is not really what a driver is supposed to be doing. These are transport enable/disable callbacks from the BT core towards the driver. It maps to a device being enabled/disabled by something like bluetoothd for example. So if disabled, users expect that no resources/queues are in use. It does work with all other transports like USB, SDIO, UART etc. There should be no buffer used if the device is powered off. We also don’t have any USB URBs in-flight if the transport is not active. The way to implement a proper fix would be using vq reset if supported, or even using a full device reset. The cost of the hack is a single skb wasted on an unused bt device. NB2: with this fix in place driver still suffers from a race condition if an interrupt triggers while device is being reset. To fix, in the virtbt_close() callback we should deactivate all interrupts. To be fixed. squashed fixup: bluetooth: virtio_bt: fix an error code in probe() Signed-off-by:Dan Carpenter <dan.carpenter@oracle.com> Reported-by:
Hulk Robot <hulkci@huawei.com> Signed-off-by:
Michael S. Tsirkin <mst@redhat.com> Message-Id: <20220811080943.198245-1-mst@redhat.com> Signed-off-by:
-
Archie Pusaka authored
If a command is already sent, we take care of freeing it, but we also need to cancel the timeout as well. Signed-off-by:
Archie Pusaka <apusaka@chromium.org> Reviewed-by:
Abhishek Pandit-Subedi <abhishekpandit@google.com> Signed-off-by:
-
Luiz Augusto von Dentz authored
force_static_address shall be writable while hdev is initing but is not considered powered yet since the static address is written only when powered. Signed-off-by:
Brian Gix <brian.gix@intel.com>
-
Luiz Augusto von Dentz authored
This attempts to program the address stored in hdev->static_addr after the init sequence has been complete: @ MGMT Command: Set Static A.. (0x002b) plen 6 Address: C0:55:44:33:22:11 (Static) @ MGMT Event: Command Complete (0x0001) plen 7 Set Static Address (0x002b) plen 4 Status: Success (0x00) Current settings: 0x00008200 Low Energy Static Address @ MGMT Event: New Settings (0x0006) plen 4 Current settings: 0x00008200 Low Energy Static Address < HCI Command: LE Set Random.. (0x08|0x0005) plen 6 Address: C0:55:44:33:22:11 (Static) > HCI Event: Command Complete (0x0e) plen 4 LE Set Random Address (0x08|0x0005) ncmd 1 Status: Success (0x00) @ MGMT Event: Command Complete (0x0001) plen 7 Set Powered (0x0005) plen 4 Status: Success (0x00) Current settings: 0x00008201 Powered Low Energy Static Address @ MGMT Event: New Settings (0x0006) plen 4 Current settings: 0x00008201 Powered Low Energy Static Address Signed-off-by: -
Nicolas Cavallari authored
The USB interface between the host and the bluetooth adapter used for SCO packets uses an USB isochronous endpoint with a fragmentation scheme that does not tolerate errors. Except USB isochronous transfers do not provide a reliable stream with guaranteed delivery. (There is no retry on error, see USB spec v2.0 5.6 and 8.5.5.) To fragment a packet, the bluetooth HCI simply splits it in parts and transfer them as-is. The receiver is expected to reconstruct the packet by assuming the first fragment contains the header and parsing its size field. There is no error detection either. If a fragment is lost, the end result is that the kernel is no longer synchronized and will pass malformed data to the upper layers, since it has no way to tell if the first fragment is an actual first fragment or a continuation fragment. Resynchronization can only happen by luck and requires an unbounded amount of time. The typical symptom for a HSP/HFP bluetooth headset is that the microphone stops working and dmesg contains piles of rate-limited "Bluetooth: hci0: SCO packet for unknown connection handle XXXX" errors for an indeterminate amount of time, until the kernel accidentally resynchronize. A workaround is to ask the upper layer to prevalidate the first fragment header. This is not possible with user channels so this workaround is disabled in this case. This problem is the most severe when using an ath3k adapter on an i.MX 6 board, where packet loss occur regularly, possibly because it is an USB1 device connected on an USB2 hub and this is a special case requiring split transactions. Signed-off-by:
Nicolas Cavallari <nicolas.cavallari@green-communications.fr> Signed-off-by:
-
Archie Pusaka authored
On cmd_timeout with no reset_gpio, reset the USB port as a last resort. This patch changes the behavior of btusb_intel_cmd_timeout and btusb_rtl_cmd_timeout. Signed-off-by:
Ying Hsu <yinghsu@chromium.org> Signed-off-by:
-
Chethan Tumkur Narayan authored
In case of suspend/resume and HCI_RESET (BT On and Off), ISOC endpoint set to alt setting 0 when no SCO connection exists. This patch shall avoid resetting of ISOC endpoint to alt setting to 0. Signed-off-by:
Chethan Tumkur Narayan <chethan.tumkur.narayan@intel.com> Signed-off-by:
Kiran K <kiran.k@intel.com> Signed-off-by:
-
Rob Herring authored
Convert the Socionext NetSec Ethernet binding to DT schema format. Signed-off-by:
Jassi Brar <jaswinder.singh@linaro.org> Link: https://lore.kernel.org/r/20221209171553.3350583-1-robh@kernel.orgSigned-off-by:
Jakub Kicinski <kuba@kernel.org>
-
Taras Chornyi authored
Taras's Marvell email account will be shut down soon so change it to Plvision. Signed-off-by:
Taras Chornyi <taras.chornyi@plvision.eu> Signed-off-by:
Vadym Kochan <vadym.kochan@plvision.eu> Link: https://lore.kernel.org/r/20221209154521.1246881-1-vadym.kochan@plvision.euSigned-off-by:
-
Xu Panda authored
The implementation of strscpy() is more robust and safer. That's now the recommended way to copy NUL terminated strings. Signed-off-by:
Xu Panda <xu.panda@zte.com.cn> Signed-off-by:
Yang Yang <yang.yang29@zte.com> Reviewed-by:
Jiri Pirko <jiri@nvidia.com> Link: https://lore.kernel.org/r/202212091538591375035@zte.com.cnSigned-off-by:
-
Firo Yang authored
Recently, a customer reported that from their container whose net namespace is different to the host's init_net, they can't set the container's net.sctp.rto_max to any value smaller than init_net.sctp.rto_min. For instance, Host: sudo sysctl net.sctp.rto_min net.sctp.rto_min = 1000 Container: echo 100 > /mnt/proc-net/sctp/rto_min echo 400 > /mnt/proc-net/sctp/rto_max echo: write error: Invalid argument This is caused by the check made from this'commit 4f3fdf3b ("sctp: add check rto_min and rto_max in sysctl")' When validating the input value, it's always referring the boundary value set for the init_net namespace. Having container's rto_max smaller than host's init_net.sctp.rto_min does make sense. Consider that the rto between two containers on the same host is very likely smaller than it for two hosts. So to fix this problem, as suggested by Marcelo, this patch makes the extra pointers of rto_min, rto_max, pf_retrans, and ps_retrans point to the corresponding variables from the newly created net namespace while the new net namespace is being registered in sctp_sysctl_net_register. Fixes: 4f3fdf3b ("sctp: add check rto_min and rto_max in sysctl") Reviewed-by:
Marcelo Ricardo Leitner <marcelo.leitner@gmail.com> Reviewed-by:
Firo Yang <firo.yang@suse.com> Link: https://lore.kernel.org/r/20221209054854.23889-1-firo.yang@suse.comSigned-off-by:
-
Roger Quadros authored
Ensure pm_runtime_put() is issued in error path. Reported-by:
Roger Quadros <rogerq@kernel.org> Reviewed-by:
Saeed Mahameed <saeed@kernel.org> Link: https://lore.kernel.org/r/20221208105534.63709-1-rogerq@kernel.orgSigned-off-by:
-
Jakub Kicinski authored
Merge tag 'wireless-next-2022-12-12' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next Kalle Valo says: ==================== wireless-next patches for v6.2 Fourth set of patches for v6.2. Few final patches, a big change is that rtw88 now has USB support. Major changes: rtw88 * support USB devices rtw8821cu, rtw8822bu, rtw8822cu and rtw8723du * tag 'wireless-next-2022-12-12' of git://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless-next: (43 commits) wifi: rtl8xxxu: fixing IQK failures for rtl8192eu wifi: rtlwifi: btcoexist: fix conditions branches that are never executed wifi: rtlwifi: rtl8192se: remove redundant rtl_get_bbreg() call wifi: rtw88: Add rtw8723du chipset support wifi: rtw88: Add rtw8822cu chipset support wifi: rtw88: Add rtw8822bu chipset support wifi: rtw88: Add rtw8821cu chipset support wifi: rtw88: Add common USB chip support wifi: rtw88: iterate over vif/sta list non-atomically wifi: rtw88: Drop coex mutex wifi: rtw88: Drop h2c.lock wifi: rtw88: Drop rf_lock wifi: rtw88: Call rtw_fw_beacon_filter_config() with rtwdev->mutex held wifi: rtw88: print firmware type in info message wifi: rtw89: add join info upon create interface wifi: rtw89: fix unsuccessful interface_add flow wifi: rtw89: stop mac port function when stop_ap() wifi: rtw89: add mac TSF sync function wifi: rtw89: request full firmware only once if it's early requested wifi: rtw89: don't request partial firmware if SECURITY_LOADPIN_ENFORCE ... ==================== Link: https://lore.kernel.org/r/20221212093026.5C5AEC433D2@smtp.kernel.orgSigned-off-by:
-
https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-nextJakub Kicinski authored
Alexei Starovoitov says: ==================== pull-request: bpf-next 2022-12-11 We've added 74 non-merge commits during the last 11 day(s) which contain a total of 88 files changed, 3362 insertions(+), 789 deletions(-). The main changes are: 1) Decouple prune and jump points handling in the verifier, from Andrii. 2) Do not rely on ALLOW_ERROR_INJECTION for fmod_ret, from Benjamin. Merged from hid tree. 3) Do not zero-extend kfunc return values. Necessary fix for 32-bit archs, from Björn. 4) Don't use rcu_users to refcount in task kfuncs, from David. 5) Three reg_state->id fixes in the verifier, from Eduard. 6) Optimize bpf_mem_alloc by reusing elements from free_by_rcu, from Hou. 7) Refactor dynptr handling in the verifier, from Kumar. 8) Remove the "/sys" mount and umount dance in {open,close}_netns in bpf selftests, from Martin. 9) Enable sleepable support for cgrp local storage, from Yonghong. * tag 'for-netdev' of https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (74 commits) selftests/bpf: test case for relaxed prunning of active_lock.id selftests/bpf: Add pruning test case for bpf_spin_lock bpf: use check_ids() for active_lock comparison selftests/bpf: verify states_equal() maintains idmap across all frames bpf: states_equal() must build idmap for all function frames selftests/bpf: test cases for regsafe() bug skipping check_id() bpf: regsafe() must not skip check_ids() docs/bpf: Add documentation for BPF_MAP_TYPE_SK_STORAGE selftests/bpf: Add test for dynptr reinit in user_ringbuf callback bpf: Use memmove for bpf_dynptr_{read,write} bpf: Move PTR_TO_STACK alignment check to process_dynptr_func bpf: Rework check_func_arg_reg_off bpf: Rework process_dynptr_func bpf: Propagate errors from process_* checks in check_func_arg bpf: Refactor ARG_PTR_TO_DYNPTR checks into process_dynptr_func bpf: Skip rcu_barrier() if rcu_trace_implies_rcu_gp() is true bpf: Reuse freed element in free_by_rcu during allocation selftests/bpf: Bring test_offload.py back to life bpf: Fix comment error in fixup_kfunc_call function bpf: Do not zero-extend kfunc return values ... ==================== Link: https://lore.kernel.org/r/20221212024701.73809-1-alexei.starovoitov@gmail.comSigned-off-by: -
David S. Miller authored
Merge tag 'linux-can-next-for-6.2-20221212' of git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can-next Marc Kleine-Budde says: ==================== linux-can-next-for-6.2-20221212 this is a pull request of 39 patches for net-next/master. The first 2 patches are by me fix a warning and coding style in the kvaser_usb driver. Vivek Yadav's patch sorts the includes of the m_can driver. Biju Das contributes 5 patches for the rcar_canfd driver improve the support for different IP core variants. Jean Delvare's patch for the ctucanfd drops the dependency on COMPILE_TEST. Vincent Mailhol's patch sorts the includes of the etas_es58x driver. Haibo Chen's contributes 2 patches that add i.MX93 support to the flexcan driver. Lad Prabhakar's patch updates the dt-bindings documentation of the rcar_canfd driver. Minghao Chi's patch converts the c_can platform driver to devm_platform_get_and_ioremap_resource(). In the next 7 patches Vincent Mailhol adds devlink support to the etas_es58x driver to report firmware, bootloader and hardware version. Xu Panda's patch converts a strncpy() -> strscpy() in the ucan driver. Ye Bin's patch removes a useless parameter from the AF_CAN protocol. The next 2 patches by Vincent Mailhol and remove unneeded or unused pointers to struct usb_interface in device's priv struct in the ucan and gs_usb driver. Vivek Yadav's patch cleans up the usage of the RAM initialization in the m_can driver. A patch by me add support for SO_MARK to the AF_CAN protocol. Geert Uytterhoeven's patch fixes the number of CAN channels in the rcan_canfd bindings documentation. In the last 11 patches Markus Schneider-Pargmann optimizes the register access in the t_can driver and cleans up the tcan glue driver. ==================== Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Marc Kleine-Budde authored
Markus Schneider-Pargmann <msp@baylibre.com> says: as requested I split the series into two parts. This is the first parts with simple improvements to reduce the number of SPI transfers. The second part will be the rest with coalescing support and more complex optimizations. Changes since v1: https://lore.kernel.org/all/20221116205308.2996556-1-msp@baylibre.com - Fixed register ranges - Added fixes: tag for two patches Link: https://lore.kernel.org/all/20221206115728.1056014-1-msp@baylibre.comSigned-off-by:
Marc Kleine-Budde <mkl@pengutronix.de>
-
Markus Schneider-Pargmann authored
Specify exactly which registers are read/writeable in the chip. This is supposed to help detect any violations in the future. Signed-off-by:
Markus Schneider-Pargmann <msp@baylibre.com> Link: https://lore.kernel.org/all/20221206115728.1056014-12-msp@baylibre.comSigned-off-by:
-
