- 20 Feb, 2015 24 commits
-
-
Sujith Manoharan authored
commit 35580d22 upstream. T: Bus=02 Lev=01 Prnt=01 Port=04 Cnt=01 Dev#= 9 Spd=12 MxCh= 0 D: Ver= 1.10 Cls=e0(wlcon) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=0489 ProdID=e05f Rev= 0.02 C:* #Ifs= 2 Cfg#= 1 Atr=e0 MxPwr=100mA A: FirstIf#= 0 IfCount= 2 Cls=e0(wlcon) Sub=01 Prot=01 I:* If#= 0 Alt= 0 #EPs= 3 Cls=e0(wlcon) Sub=01 Prot=01 Driver=btusb Reported-by:
Joshua Richenhagen <richenhagen@gmail.com> Signed-off-by:
Sujith Manoharan <sujith@msujith.org> Signed-off-by:
Johan Hedberg <johan.hedberg@intel.com> Signed-off-by:
Ben Hutchings <ben@decadent.org.uk>
-
Ken O'Brien authored
commit 5bcecf32 upstream. Add generic rule on encountering Belkin bluetooth usb device F8065bf. Relevant section from /sys/kernel/debug/usb/devices: T: Bus=03 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=12 MxCh= 0 D: Ver= 2.00 Cls=ff(vend.) Sub=01 Prot=01 MxPS=64 #Cfgs= 1 P: Vendor=050d ProdID=065a Rev= 1.12 S: Manufacturer=Broadcom Corp S: Product=BCM20702A0 S: SerialNumber=0002723E2D29 C:* #Ifs= 4 Cfg#= 1 Atr=a0 MxPwr=100mA I:* If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=81(I) Atr=03(Int.) MxPS= 16 Ivl=1ms E: Ad=82(I) Atr=02(Bulk) MxPS= 64 Ivl=0ms E: Ad=02(O) Atr=02(Bulk) MxPS= 64 Ivl=0ms I:* If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 0 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 0 Ivl=1ms I: If#= 1 Alt= 1 #EPs= 2 Cls=ff(vend.) Sub=01 Prot=01 Driver=btusb E: Ad=83(I) Atr=01(Isoc) MxPS= 9 Ivl=1ms E: Ad=03(O) Atr=01(Isoc) MxPS= 9 Ivl=1ms Signed-off-by:
Ken O'Brien <kernel@kenobrien.org> Signed-off-by:
Gustavo Padovan <gustavo.padovan@collabora.co.uk> Signed-off-by:
-
Robert Baldyga authored
commit 1ff383a4 upstream. This patch adds waiting until transmit buffer and shifter will be empty before clock disabling. Without this fix it's possible to have clock disabled while data was not transmited yet, which causes unproper state of TX line and problems in following data transfers. Signed-off-by:
Robert Baldyga <r.baldyga@samsung.com> Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Dmitry Eremin-Solenikov authored
commit 1a5fb99d upstream. Some boards with TC6393XB chip require full state restore during system resume thanks to chip's VCC being cut off during suspend (Sharp SL-6000 tosa is one of them). Failing to do so would result in ohci Oops on resume due to internal memory contentes being changed. Fail ohci suspend on tc6393xb is full state restore is required. Recommended workaround is to unbind tmio-ohci driver before suspend and rebind it after resume. Signed-off-by:
Dmitry Eremin-Solenikov <dbaryshkov@gmail.com> Signed-off-by:
Lee Jones <lee.jones@linaro.org> Signed-off-by:
-
Takashi Iwai authored
commit 2228d80d upstream. We've got a bug report at disconnecting a Webcam, where the kernel spews warnings like below: WARNING: CPU: 0 PID: 8385 at ../fs/sysfs/group.c:219 sysfs_remove_group+0x87/0x90() sysfs group c0b2350c not found for kobject 'event3' CPU: 0 PID: 8385 Comm: queue2:src Not tainted 3.16.2-1.gdcee397-default #1 Hardware name: ASUSTeK Computer INC. A7N8X-E/A7N8X-E, BIOS ASUS A7N8X-E Deluxe ACPI BIOS Rev 1013 11/12/2004 c08d0705 ddc75cbc c0718c5b ddc75ccc c024b654 c08c6d44 ddc75ce8 000020c1 c08d0705 000000db c03d1ec7 c03d1ec7 00000009 00000000 c0b2350c d62c9064 ddc75cd4 c024b6a3 00000009 ddc75ccc c08c6d44 ddc75ce8 ddc75cfc c03d1ec7 Call Trace: [<c0205ba6>] try_stack_unwind+0x156/0x170 [<c02046f3>] dump_trace+0x53/0x180 [<c0205c06>] show_trace_log_lvl+0x46/0x50 [<c0204871>] show_stack_log_lvl+0x51/0xe0 [<c0205c67>] show_stack+0x27/0x50 [<c0718c5b>] dump_stack+0x3e/0x4e [<c024b654>] warn_slowpath_common+0x84/0xa0 [<c024b6a3>] warn_slowpath_fmt+0x33/0x40 [<c03d1ec7>] sysfs_remove_group+0x87/0x90 [<c05a2c54>] device_del+0x34/0x180 [<c05e3989>] evdev_disconnect+0x19/0x50 [<c05e06fa>] __input_unregister_device+0x9a/0x140 [<c05e0845>] input_unregister_device+0x45/0x80 [<f854b1d6>] uvc_delete+0x26/0x110 [uvcvideo] [<f84d66f8>] v4l2_device_release+0x98/0xc0 [videodev] [<c05a25bb>] device_release+0x2b/0x90 [<c04ad8bf>] kobject_cleanup+0x6f/0x1a0 [<f84d5453>] v4l2_release+0x43/0x70 [videodev] [<c0372f31>] __fput+0xb1/0x1b0 [<c02650c1>] task_work_run+0x91/0xb0 [<c024d845>] do_exit+0x265/0x910 [<c024df64>] do_group_exit+0x34/0xa0 [<c025a76f>] get_signal_to_deliver+0x17f/0x590 [<c0201b6a>] do_signal+0x3a/0x960 [<c02024f7>] do_notify_resume+0x67/0x90 [<c071ebb5>] work_notifysig+0x30/0x3b [<b7739e60>] 0xb7739e5f ---[ end trace b1e56095a485b631 ]--- The cause is that uvc_status_cleanup() is called after usb_put_*() in uvc_delete(). usb_put_*() removes the sysfs parent and eventually removes the children recursively, so the later device_del() can't find its sysfs. The fix is simply rearrange the call orders in uvc_delete() so that the child is removed before the parent. Bugzilla: https://bugzilla.suse.com/show_bug.cgi?id=897736Reported-and-tested-by:
Martin Pluskal <mpluskal@suse.com> Signed-off-by:
Takashi Iwai <tiwai@suse.de> Signed-off-by:
Laurent Pinchart <laurent.pinchart@ideasonboard.com> Signed-off-by:
Mauro Carvalho Chehab <mchehab@osg.samsung.com> [bwh: Backported to 3.2: adjust filename] Signed-off-by:
-
Greg Kroah-Hartman authored
commit 403dff4e upstream. We need to check that we have both a valid data and control inteface for both types of headers (union and not union.) References: https://bugzilla.kernel.org/show_bug.cgi?id=83551Reported-by:
Simon Schubert <2+kernel@0x2c.org> Signed-off-by:
-
Jens Axboe authored
commit 5fabcb4c upstream. We can get here from blkdev_ioctl() -> blkpg_ioctl() -> add_partition() with a user passed in partno value. If we pass in 0x7fffffff, the new target in disk_expand_part_tbl() overflows the 'int' and we access beyond the end of ptbl->part[] and even write to it when we do the rcu_assign_pointer() to assign the new partition. Reported-by:
David Ramos <daramos@stanford.edu> Signed-off-by:
Jens Axboe <axboe@fb.com> Signed-off-by:
-
Keerthy authored
commit c4cf0935 upstream. Correct returning IRQ_HANDLED unconditionally in the irq handler. Return IRQ_NONE for some interrupt which we do not expect to be handled in this handler. This prevents kernel stalling with back to back spurious interrupts. Fixes: 2722e56d ("OMAP4: l3: Introduce l3-interconnect error handling driver") Acked-by:
Nishanth Menon <nm@ti.com> Signed-off-by:
Keerthy <j-keerthy@ti.com> Signed-off-by:
Tony Lindgren <tony@atomide.com> [bwh: Backported to 3.2: adjust filename, indentation] Signed-off-by:
-
Hannes Reinecke authored
commit b6c92b7e upstream. The .eh_abort_handler needs to return SUCCESS, FAILED, or FAST_IO_FAIL. So fixup all callers to adhere to this requirement. Reviewed-by:
Robert Elliott <elliott@hp.com> Signed-off-by:
Hannes Reinecke <hare@suse.de> Signed-off-by:
Christoph Hellwig <hch@lst.de> [bwh: Backported to 3.2: drop changes to esas2r] Signed-off-by:
-
Myron Stowe authored
commit 36e81648 upstream. Commit 6ac665c6 ("PCI: rewrite PCI BAR reading code") masked off low-order bits from 'l', but not from 'sz'. Both are passed to pci_size(), which compares 'base == maxbase' to check for read-only BARs. The masking of 'l' means that comparison will never be 'true', so the check for read-only BARs no longer works. Resolve this by also masking off the low-order bits of 'sz' before passing it into pci_size() as 'maxbase'. With this change, pci_size() will once again catch the problems that have been encountered to date: - AGP aperture BAR of AMD-7xx host bridges: if the AGP window is disabled, this BAR is read-only and read as 0x00000008 [1] - BARs 0-4 of ALi IDE controllers can be non-zero and read-only [1] - Intel Sandy Bridge - Thermal Management Controller [8086:0103]; BAR 0 returning 0xfed98004 [2] - Intel Xeon E5 v3/Core i7 Power Control Unit [8086:2fc0]; Bar 0 returning 0x00001a [3] Link: [1] https://git.kernel.org/cgit/linux/kernel/git/tglx/history.git/commit/drivers/pci/probe.c?id=1307ef6621991f1c4bc3cec1b5a4ebd6fd3d66b9 ("PCI: probing read-only BARs" (pre-git)) Link: [2] https://bugzilla.kernel.org/show_bug.cgi?id=43331 Link: [3] https://bugzilla.kernel.org/show_bug.cgi?id=85991Reported-by:
William Unruh <unruh@physics.ubc.ca> Reported-by:
Martin Lucina <martin@lucina.net> Signed-off-by:
Myron Stowe <myron.stowe@redhat.com> Signed-off-by:
Bjorn Helgaas <bhelgaas@google.com> CC: Matthew Wilcox <willy@linux.intel.com> Signed-off-by:
-
Lars Ellenberg authored
commit 3b9d35d7 upstream. This was not noticed for many years. Affects operation if md raid is used a backing device for DRBD. Signed-off-by:
Philipp Reisner <philipp.reisner@linbit.com> Signed-off-by:
Lars Ellenberg <lars.ellenberg@linbit.com> Signed-off-by:
-
Alex Williamson authored
commit 0372ffb3 upstream. bus_find_device_by_name() acquires a device reference which is never released. This results in an object leak, which on older kernels results in failure to release all resources of PCI devices. libvirt uses drivers_probe to re-attach devices to the host after assignment and is therefore a common trigger for this leak. Example: # cd /sys/bus/pci/ # dmesg -C # echo 1 > devices/0000\:01\:00.0/sriov_numvfs # echo 0 > devices/0000\:01\:00.0/sriov_numvfs # dmesg | grep 01:10 pci 0000:01:10.0: [8086:10ca] type 00 class 0x020000 kobject: '0000:01:10.0' (ffff8801d79cd0a8): kobject_add_internal: parent: '0000:00:01.0', set: 'devices' kobject: '0000:01:10.0' (ffff8801d79cd0a8): kobject_uevent_env kobject: '0000:01:10.0' (ffff8801d79cd0a8): fill_kobj_path: path = '/devices/pci0000:00/0000:00:01.0/0000:01:10.0' kobject: '0000:01:10.0' (ffff8801d79cd0a8): kobject_uevent_env kobject: '0000:01:10.0' (ffff8801d79cd0a8): fill_kobj_path: path = '/devices/pci0000:00/0000:00:01.0/0000:01:10.0' kobject: '0000:01:10.0' (ffff8801d79cd0a8): kobject_uevent_env kobject: '0000:01:10.0' (ffff8801d79cd0a8): fill_kobj_path: path = '/devices/pci0000:00/0000:00:01.0/0000:01:10.0' kobject: '0000:01:10.0' (ffff8801d79cd0a8): kobject_cleanup, parent (null) kobject: '0000:01:10.0' (ffff8801d79cd0a8): calling ktype release kobject: '0000:01:10.0': free name [kobject freed as expected] # dmesg -C # echo 1 > devices/0000\:01\:00.0/sriov_numvfs # echo 0000:01:10.0 > drivers_probe # echo 0 > devices/0000\:01\:00.0/sriov_numvfs # dmesg | grep 01:10 pci 0000:01:10.0: [8086:10ca] type 00 class 0x020000 kobject: '0000:01:10.0' (ffff8801d79ce0a8): kobject_add_internal: parent: '0000:00:01.0', set: 'devices' kobject: '0000:01:10.0' (ffff8801d79ce0a8): kobject_uevent_env kobject: '0000:01:10.0' (ffff8801d79ce0a8): fill_kobj_path: path = '/devices/pci0000:00/0000:00:01.0/0000:01:10.0' kobject: '0000:01:10.0' (ffff8801d79ce0a8): kobject_uevent_env kobject: '0000:01:10.0' (ffff8801d79ce0a8): fill_kobj_path: path = '/devices/pci0000:00/0000:00:01.0/0000:01:10.0' kobject: '0000:01:10.0' (ffff8801d79ce0a8): kobject_uevent_env kobject: '0000:01:10.0' (ffff8801d79ce0a8): fill_kobj_path: path = '/devices/pci0000:00/0000:00:01.0/0000:01:10.0' [no free] Signed-off-by:
Alex Williamson <alex.williamson@redhat.com> Signed-off-by:
-
Richard Weinberger authored
commit f38aed97 upstream. The logic of vfree()'ing vol->upd_buf is tied to vol->updating. In ubi_start_update() vol->updating is set long before vmalloc()'ing vol->upd_buf. If we encounter a write failure in ubi_start_update() before vmalloc() the UBI device release function will try to vfree() vol->upd_buf because vol->updating is set. Fix this by allocating vol->upd_buf directly after setting vol->updating. Fixes: [ 31.559338] UBI warning: vol_cdev_release: update of volume 2 not finished, volume is damaged [ 31.559340] ------------[ cut here ]------------ [ 31.559343] WARNING: CPU: 1 PID: 2747 at mm/vmalloc.c:1446 __vunmap+0xe3/0x110() [ 31.559344] Trying to vfree() nonexistent vm area (ffffc90001f2b000) [ 31.559345] Modules linked in: [ 31.565620] 0000000000000bba ffff88002a0cbdb0 ffffffff818f0497 ffff88003b9ba148 [ 31.566347] ffff88002a0cbde0 ffffffff8156f515 ffff88003b9ba148 0000000000000bba [ 31.567073] 0000000000000000 0000000000000000 ffff88002a0cbe88 ffffffff8156c10a [ 31.567793] Call Trace: [ 31.568034] [<ffffffff818f0497>] dump_stack+0x4e/0x7a [ 31.568510] [<ffffffff8156f515>] ubi_io_write_vid_hdr+0x155/0x160 [ 31.569084] [<ffffffff8156c10a>] ubi_eba_write_leb+0x23a/0x870 [ 31.569628] [<ffffffff81569b36>] vol_cdev_write+0x226/0x380 [ 31.570155] [<ffffffff81179265>] vfs_write+0xb5/0x1f0 [ 31.570627] [<ffffffff81179f8a>] SyS_pwrite64+0x6a/0xa0 [ 31.571123] [<ffffffff818fde12>] system_call_fastpath+0x16/0x1b Signed-off-by:
Richard Weinberger <richard@nod.at> Signed-off-by:
Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by:
-
Christian Borntraeger authored
commit 2dca485f upstream. some control register changes will flush some aspects of the CPU, e.g. POP explicitely mentions that for CR9-CR11 "TLBs may be cleared". Instead of trying to be clever and only flush on specific CRs, let play safe and flush on all lctl(g) as future machines might define new bits in CRs. Load control intercept should not happen that often. Signed-off-by:
Christian Borntraeger <borntraeger@de.ibm.com> Acked-by:
Cornelia Huck <cornelia.huck@de.ibm.com> Reviewed-by:
David Hildenbrand <dahi@linux.vnet.ibm.com> [bwh: Backported to 3.2: adjust filename, context] Signed-off-by:
-
Daniel Borkmann authored
commit 4c672e4b upstream. It has been reported that generating an MLD listener report on devices with large MTUs (e.g. 9000) and a high number of IPv6 addresses can trigger a skb_over_panic(): skbuff: skb_over_panic: text:ffffffff80612a5d len:3776 put:20 head:ffff88046d751000 data:ffff88046d751010 tail:0xed0 end:0xec0 dev:port1 ------------[ cut here ]------------ kernel BUG at net/core/skbuff.c:100! invalid opcode: 0000 [#1] SMP Modules linked in: ixgbe(O) CPU: 3 PID: 0 Comm: swapper/3 Tainted: G O 3.14.23+ #4 [...] Call Trace: <IRQ> [<ffffffff80578226>] ? skb_put+0x3a/0x3b [<ffffffff80612a5d>] ? add_grhead+0x45/0x8e [<ffffffff80612e3a>] ? add_grec+0x394/0x3d4 [<ffffffff80613222>] ? mld_ifc_timer_expire+0x195/0x20d [<ffffffff8061308d>] ? mld_dad_timer_expire+0x45/0x45 [<ffffffff80255b5d>] ? call_timer_fn.isra.29+0x12/0x68 [<ffffffff80255d16>] ? run_timer_softirq+0x163/0x182 [<ffffffff80250e6f>] ? __do_softirq+0xe0/0x21d [<ffffffff8025112b>] ? irq_exit+0x4e/0xd3 [<ffffffff802214bb>] ? smp_apic_timer_interrupt+0x3b/0x46 [<ffffffff8063f10a>] ? apic_timer_interrupt+0x6a/0x70 mld_newpack() skb allocations are usually requested with dev->mtu in size, since commit 72e09ad1 ("ipv6: avoid high order allocations") we have changed the limit in order to be less likely to fail. However, in MLD/IGMP code, we have some rather ugly AVAILABLE(skb) macros, which determine if we may end up doing an skb_put() for adding another record. To avoid possible fragmentation, we check the skb's tailroom as skb->dev->mtu - skb->len, which is a wrong assumption as the actual max allocation size can be much smaller. The IGMP case doesn't have this issue as commit 57e1ab6e ("igmp: refine skb allocations") stores the allocation size in the cb[]. Set a reserved_tailroom to make it fit into the MTU and use skb_availroom() helper instead. This also allows to get rid of igmp_skb_size(). Reported-by:
Wei Liu <lw1a2.jing@gmail.com> Fixes: 72e09ad1 ("ipv6: avoid high order allocations") Signed-off-by:
Daniel Borkmann <dborkman@redhat.com> Cc: Eric Dumazet <edumazet@google.com> Cc: Hannes Frederic Sowa <hannes@stressinduktion.org> Cc: David L Stevens <david.stevens@oracle.com> Acked-by:
Eric Dumazet <edumazet@google.com> Acked-by:
Hannes Frederic Sowa <hannes@stressinduktion.org> Signed-off-by:
David S. Miller <davem@davemloft.net> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Herbert Xu authored
commit a7ae1992 upstream. ipv6: Remove all uses of LL_ALLOCATED_SPACE The macro LL_ALLOCATED_SPACE was ill-conceived. It applies the alignment to the sum of needed_headroom and needed_tailroom. As the amount that is then reserved for head room is needed_headroom with alignment, this means that the tail room left may be too small. This patch replaces all uses of LL_ALLOCATED_SPACE in net/ipv6 with the macro LL_RESERVED_SPACE and direct reference to needed_tailroom. This also fixes the problem with needed_headroom changing between allocating the skb and reserving the head room. Signed-off-by:
Herbert Xu <herbert@gondor.apana.org.au> Signed-off-by:
-
Herbert Xu authored
commit 66088243 upstream. ipv4: Remove all uses of LL_ALLOCATED_SPACE The macro LL_ALLOCATED_SPACE was ill-conceived. It applies the alignment to the sum of needed_headroom and needed_tailroom. As the amount that is then reserved for head room is needed_headroom with alignment, this means that the tail room left may be too small. This patch replaces all uses of LL_ALLOCATED_SPACE in net/ipv4 with the macro LL_RESERVED_SPACE and direct reference to needed_tailroom. This also fixes the problem with needed_headroom changing between allocating the skb and reserving the head room. Signed-off-by:
-
Kazuya Mizuguchi authored
commit 11432050 upstream. This patch fixes an issue that the NULL pointer dereference happens when we uses g_audio driver. Since the g_audio driver will call usb_ep_disable() in afunc_set_alt() before it calls usb_ep_enable(), the uep->pipe of renesas usbhs driver will be NULL. So, this patch adds a condition to avoid the oops. Signed-off-by:
Kazuya Mizuguchi <kazuya.mizuguchi.ks@renesas.com> Signed-off-by:
Takeshi Kihara <takeshi.kihara.df@renesas.com> Signed-off-by:
Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com> Fixes: 2f98382d (usb: renesas_usbhs: Add Renesas USBHS Gadget) Signed-off-by:
Felipe Balbi <balbi@ti.com> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Tejun Heo authored
commit 9c6ac78e upstream. After invoking ->dirty_inode(), __mark_inode_dirty() does smp_mb() and tests inode->i_state locklessly to see whether it already has all the necessary I_DIRTY bits set. The comment above the barrier doesn't contain any useful information - memory barriers can't ensure "changes are seen by all cpus" by itself. And it sure enough was broken. Please consider the following scenario. CPU 0 CPU 1 ------------------------------------------------------------------------------- enters __writeback_single_inode() grabs inode->i_lock tests PAGECACHE_TAG_DIRTY which is clear enters __set_page_dirty() grabs mapping->tree_lock sets PAGECACHE_TAG_DIRTY releases mapping->tree_lock leaves __set_page_dirty() enters __mark_inode_dirty() smp_mb() sees I_DIRTY_PAGES set leaves __mark_inode_dirty() clears I_DIRTY_PAGES releases inode->i_lock Now @inode has dirty pages w/ I_DIRTY_PAGES clear. This doesn't seem to lead to an immediately critical problem because requeue_inode() later checks PAGECACHE_TAG_DIRTY instead of I_DIRTY_PAGES when deciding whether the inode needs to be requeued for IO and there are enough unintentional memory barriers inbetween, so while the inode ends up with inconsistent I_DIRTY_PAGES flag, it doesn't fall off the IO list. The lack of explicit barrier may also theoretically affect the other I_DIRTY bits which deal with metadata dirtiness. There is no guarantee that a strong enough barrier exists between I_DIRTY_[DATA]SYNC clearing and write_inode() writing out the dirtied inode. Filesystem inode writeout path likely has enough stuff which can behave as full barrier but it's theoretically possible that the writeout may not see all the updates from ->dirty_inode(). Fix it by adding an explicit smp_mb() after I_DIRTY clearing. Note that I_DIRTY_PAGES needs a special treatment as it always needs to be cleared to be interlocked with the lockless test on __mark_inode_dirty() side. It's cleared unconditionally and reinstated after smp_mb() if the mapping still has dirty pages. Also add comments explaining how and why the barriers are paired. Lightly tested. Signed-off-by:
Tejun Heo <tj@kernel.org> Cc: Jan Kara <jack@suse.cz> Cc: Mikulas Patocka <mpatocka@redhat.com> Cc: Jens Axboe <axboe@kernel.dk> Cc: Al Viro <viro@zeniv.linux.org.uk> Reviewed-by:
Jan Kara <jack@suse.cz> Signed-off-by:
-
Jan Kara authored
commit 6290be1c upstream. Instead of clearing I_DIRTY_PAGES and resetting it when we didn't succeed in writing them all, just clear the bit only when we succeeded writing all the pages. We also move the clearing of the bit close to other i_state handling to separate it from writeback list handling. This is desirable because list handling will differ for flusher thread and other writeback_single_inode() callers in future. No filesystem plays any tricks with I_DIRTY_PAGES (like checking it in ->writepages or ->write_inode implementation) so this movement is safe. Signed-off-by:
Fengguang Wu <fengguang.wu@intel.com> Signed-off-by:
-
Frank Schaefer authored
commit 22799487 upstream. This patches fixes an ancient bug in the dvb_usb_af9005 driver, which has been reported at least in the following threads: https://lkml.org/lkml/2009/2/4/350 https://lkml.org/lkml/2014/9/18/558 If the driver is compiled in without any IR support (neither DVB_USB_AF9005_REMOTE nor custom symbols), the symbol_request calls in af9005_usb_module_init() return pointers != NULL although the IR symbols are not available. This leads to the following oops: ... [ 8.529751] usbcore: registered new interface driver dvb_usb_af9005 [ 8.531584] BUG: unable to handle kernel paging request at 02e00000 [ 8.533385] IP: [<7d9d67c6>] af9005_usb_module_init+0x6b/0x9d [ 8.535613] *pde = 00000000 [ 8.536416] Oops: 0000 [#1] PREEMPT PREEMPT DEBUG_PAGEALLOCDEBUG_PAGEALLOC [ 8.537863] CPU: 0 PID: 1 Comm: swapper Not tainted 3.15.0-rc6-00151-ga5c075cf #1 [ 8.539827] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.7.5-20140531_083030-gandalf 04/01/2014 [ 8.541519] task: 89c9a670 ti: 89c9c000 task.ti: 89c9c000 [ 8.541519] EIP: 0060:[<7d9d67c6>] EFLAGS: 00010206 CPU: 0 [ 8.541519] EIP is at af9005_usb_module_init+0x6b/0x9d [ 8.541519] EAX: 02e00000 EBX: 00000000 ECX: 00000006 EDX: 00000000 [ 8.541519] ESI: 00000000 EDI: 7da33ec8 EBP: 89c9df30 ESP: 89c9df2c [ 8.541519] DS: 007b ES: 007b FS: 0000 GS: 00e0 SS: 0068 [ 8.541519] CR0: 8005003b CR2: 02e00000 CR3: 05a54000 CR4: 00000690 [ 8.541519] Stack: [ 8.541519] 7d9d675b 89c9df90 7d992a49 7d7d5914 89c9df4c 7be3a800 7d08c58c 8a4c3968 [ 8.541519] 89c9df80 7be3a966 00000192 00000006 00000006 7d7d3ff4 8a4c397a 00000200 [ 8.541519] 7d6b1280 8a4c3979 00000006 000009a6 7da32db8 b13eec81 00000006 000009a6 [ 8.541519] Call Trace: [ 8.541519] [<7d9d675b>] ? ttusb2_driver_init+0x16/0x16 [ 8.541519] [<7d992a49>] do_one_initcall+0x77/0x106 [ 8.541519] [<7be3a800>] ? parameqn+0x2/0x35 [ 8.541519] [<7be3a966>] ? parse_args+0x113/0x25c [ 8.541519] [<7d992bc2>] kernel_init_freeable+0xea/0x167 [ 8.541519] [<7cf01070>] kernel_init+0x8/0xb8 [ 8.541519] [<7cf27ec0>] ret_from_kernel_thread+0x20/0x30 [ 8.541519] [<7cf01068>] ? rest_init+0x10c/0x10c [ 8.541519] Code: 08 c2 c7 05 44 ed f9 7d 00 00 e0 02 c7 05 40 ed f9 7d 00 00 e0 02 c7 05 3c ed f9 7d 00 00 e0 02 75 1f b8 00 00 e0 02 85 c0 74 16 <a1> 00 00 e0 02 c7 05 54 84 8e 7d 00 00 e0 02 a3 58 84 8e 7d eb [ 8.541519] EIP: [<7d9d67c6>] af9005_usb_module_init+0x6b/0x9d SS:ESP 0068:89c9df2c [ 8.541519] CR2: 0000000002e00000 [ 8.541519] ---[ end trace 768b6faf51370fc7 ]--- The prefered fix would be to convert the whole IR code to use the kernel IR infrastructure (which wasn't available at the time this driver had been created). Until anyone who still has this old hardware steps up an does the conversion, fix it by not calling the symbol_request calls if the driver is compiled in without the default IR symbols (CONFIG_DVB_USB_AF9005_REMOTE). Due to the IR related pointers beeing NULL by default, IR support will then be disabled. The downside of this solution is, that it will no longer be possible to compile custom IR symbols (not using CONFIG_DVB_USB_AF9005_REMOTE) in. Please note that this patch has NOT been tested with all possible cases. I don't have the hardware and could only verify that it fixes the reported bug. Reported-by:
Frank Schäfer <fschaefer.oss@googlemail.com> Acked-by:
Luca Olivetti <luca@ventoso.org> Signed-off-by:
-
Mauro Carvalho Chehab authored
commit 678fa12f upstream. The au0828 quirks table is currently not in sync with the au0828 media driver. Syncronize it and put them on the same order as found at au0828 driver, as all the au0828 devices with analog TV need the same quirks. Signed-off-by:
-
Mauro Carvalho Chehab authored
commit 5d1f00a2 upstream. Add a macro to simplify au0828 quirk table. That makes easier to check it against the USB IDs at drivers/media/usb/au0828/au0828-cards.c. Signed-off-by:
-
Tyler Hicks authored
commit 332b122d upstream. The ecryptfs_encrypted_view mount option greatly changes the functionality of an eCryptfs mount. Instead of encrypting and decrypting lower files, it provides a unified view of the encrypted files in the lower filesystem. The presence of the ecryptfs_encrypted_view mount option is intended to force a read-only mount and modifying files is not supported when the feature is in use. See the following commit for more information: e77a56dd [PATCH] eCryptfs: Encrypted passthrough This patch forces the mount to be read-only when the ecryptfs_encrypted_view mount option is specified by setting the MS_RDONLY flag on the superblock. Additionally, this patch removes some broken logic in ecryptfs_open() that attempted to prevent modifications of files when the encrypted view feature was in use. The check in ecryptfs_open() was not sufficient to prevent file modifications using system calls that do not operate on a file descriptor. Signed-off-by:
Tyler Hicks <tyhicks@canonical.com> Reported-by:
Priya Bansal <p.bansal@samsung.com> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
- 01 Jan, 2015 16 commits
-
-
Ben Hutchings authored
-
Paolo Bonzini authored
commit c1118b36 upstream. On x86_64, kernel text mappings are mapped read-only with CONFIG_DEBUG_RODATA. In that case, KVM will fail to patch VMCALL instructions to VMMCALL as required on AMD processors. The failure mode is currently a divide-by-zero exception, which obviously is a KVM bug that has to be fixed. However, picking the right instruction between VMCALL and VMMCALL will be faster and will help if you cannot upgrade the hypervisor. Reported-by:
Chris Webb <chris@arachsys.com> Tested-by:
Borislav Petkov <bp@suse.de> Signed-off-by:
Paolo Bonzini <pbonzini@redhat.com> [bwh: Backported to 3.2: adjust context] Signed-off-by:
-
Daniel Borkmann authored
commit 9772b54c upstream. To accomodate for enough headroom for tunnels, use MAX_HEADER instead of LL_MAX_HEADER. Robert reported that he has hit after roughly 40hrs of trinity an skb_under_panic() via SCTP output path (see reference). I couldn't reproduce it from here, but not using MAX_HEADER as elsewhere in other protocols might be one possible cause for this. In any case, it looks like accounting on chunks themself seems to look good as the skb already passed the SCTP output path and did not hit any skb_over_panic(). Given tunneling was enabled in his .config, the headroom would have been expanded by MAX_HEADER in this case. Reported-by:
Robert Święcki <robert@swiecki.net> Reference: https://lkml.org/lkml/2014/12/1/507 Fixes: 594ccc14 ("[SCTP] Replace incorrect use of dev_alloc_skb with alloc_skb in sctp_packet_transmit().") Signed-off-by:
Vlad Yasevich <vyasevich@gmail.com> Acked-by:
Neil Horman <nhorman@tuxdriver.com> Signed-off-by:
-
Ben Hutchings authored
commit de11b0e8 upstream. These drivers now call ipv6_proxy_select_ident(), which is defined only if CONFIG_INET is enabled. However, they have really depended on CONFIG_INET for as long as they have allowed sending GSO packets from userland. Reported-by:
-
Vasily Averin authored
commit 4062090e upstream. ip_setup_cork() called inside ip_append_data() steals dst entry from rt to cork and in case errors in __ip_append_data() nobody frees stolen dst entry Fixes: 2e77d89b ("net: avoid a pair of dst_hold()/dst_release() in ip_append_data()") Signed-off-by:
Vasily Averin <vvs@parallels.com> Acked-by:
-
Eric Dumazet authored
commit 349ce993 upstream. percpu tcp_md5sig_pool contains memory blobs that ultimately go through sg_set_buf(). -> sg_set_page(sg, virt_to_page(buf), buflen, offset_in_page(buf)); This requires that whole area is in a physically contiguous portion of memory. And that @buf is not backed by vmalloc(). Given that alloc_percpu() can use vmalloc() areas, this does not fit the requirements. Replace alloc_percpu() by a static DEFINE_PER_CPU() as tcp_md5sig_pool is small anyway, there is no gain to dynamically allocate it. Signed-off-by:
Crestez Dan Leonard <cdleonard@gmail.com> Signed-off-by:
-
Eric Dumazet authored
commit 71cea17e upstream. TCP md5 code uses per cpu variables but protects access to them with a shared spinlock, which is a contention point. [ tcp_md5sig_pool_lock is locked twice per incoming packet ] Makes things much simpler, by allocating crypto structures once, first time a socket needs md5 keys, and not deallocating them as they are really small. Next step would be to allow crypto allocations being done in a NUMA aware way. Signed-off-by:
-
Jiri Pirko authored
commit f76936d0 upstream. fib_nh_match does not match nexthops correctly. Example: ip route add 172.16.10/24 nexthop via 192.168.122.12 dev eth0 \ nexthop via 192.168.122.13 dev eth0 ip route del 172.16.10/24 nexthop via 192.168.122.14 dev eth0 \ nexthop via 192.168.122.15 dev eth0 Del command is successful and route is removed. After this patch applied, the route is correctly matched and result is: RTNETLINK answers: No such process Please consider this for stable trees as well. Fixes: 4e902c57 ("[IPv4]: FIB configuration using struct fib_config") Signed-off-by:
Jiri Pirko <jiri@resnulli.us> Acked-by:
-
Daniel Borkmann authored
commit 4184b2a7 upstream. A very minimal and simple user space application allocating an SCTP socket, setting SCTP_AUTH_KEY setsockopt(2) on it and then closing the socket again will leak the memory containing the authentication key from user space: unreferenced object 0xffff8800837047c0 (size 16): comm "a.out", pid 2789, jiffies 4296954322 (age 192.258s) hex dump (first 16 bytes): 01 00 00 00 04 00 00 00 00 00 00 00 00 00 00 00 ................ backtrace: [<ffffffff816d7e8e>] kmemleak_alloc+0x4e/0xb0 [<ffffffff811c88d8>] __kmalloc+0xe8/0x270 [<ffffffffa0870c23>] sctp_auth_create_key+0x23/0x50 [sctp] [<ffffffffa08718b1>] sctp_auth_set_key+0xa1/0x140 [sctp] [<ffffffffa086b383>] sctp_setsockopt+0xd03/0x1180 [sctp] [<ffffffff815bfd94>] sock_common_setsockopt+0x14/0x20 [<ffffffff815beb61>] SyS_setsockopt+0x71/0xd0 [<ffffffff816e58a9>] system_call_fastpath+0x12/0x17 [<ffffffffffffffff>] 0xffffffffffffffff This is bad because of two things, we can bring down a machine from user space when auth_enable=1, but also we would leave security sensitive keying material in memory without clearing it after use. The issue is that sctp_auth_create_key() already sets the refcount to 1, but after allocation sctp_auth_set_key() does an additional refcount on it, and thus leaving it around when we free the socket. Fixes: 65b07e5d ("[SCTP]: API updates to suport SCTP-AUTH extensions.") Signed-off-by:
-
Ben Hutchings authored
commit 5188cd44 upstream. UFO is now disabled on all drivers that work with virtio net headers, but userland may try to send UFO/IPv6 packets anyway. Instead of sending with ID=0, we should select identifiers on their behalf (as we used to). Signed-off-by:
-
Ard Biesheuvel authored
commit 8ceee728 upstream. The GHASH setkey() function uses SSE registers but fails to call kernel_fpu_begin()/kernel_fpu_end(). Instead of adding these calls, and then having to deal with the restriction that they cannot be called from interrupt context, move the setkey() implementation to the C domain. Note that setkey() does not use any particular SSE features and is not expected to become a performance bottleneck. Signed-off-by:
Ard Biesheuvel <ard.biesheuvel@linaro.org> Acked-by:
H. Peter Anvin <hpa@linux.intel.com> Fixes: 0e1227d3 (crypto: ghash - Add PCLMULQDQ accelerated implementation) Signed-off-by:
-
David Herrmann authored
commit 101b96f3 upstream. DRM_IOCTL_MODE_GETFB is used to retrieve information about a given framebuffer ID. It is a read-only helper and was thus declassified for unprivileged access in: commit a14b1b42 Author: Mandeep Singh Baines <mandeep.baines@gmail.com> Date: Fri Jan 20 12:11:16 2012 -0800 drm: remove master fd restriction on mode setting getters However, alongside width, height and stride information, DRM_IOCTL_MODE_GETFB also passes back a handle to the underlying buffer of the framebuffer. This handle allows users to mmap() it and read or write into it. Obviously, this should be restricted to DRM-Master. With the current setup, *any* process with access to /dev/dri/card0 (which means any process with access to hardware-accelerated rendering) can access the current screen framebuffer and modify it ad libitum. For backwards-compatibility reasons we want to keep the DRM_IOCTL_MODE_GETFB call unprivileged. Besides, it provides quite useful information regarding screen setup. So we simply test whether the caller is the current DRM-Master and if not, we return 0 as handle, which is always invalid. A following DRM_IOCTL_GEM_CLOSE on this handle will fail with EINVAL, but we accept this. Users shouldn't test for errors during GEM_CLOSE, anyway. And it is still better as a failing MODE_GETFB call. v2: add capable(CAP_SYS_ADMIN) check for compatibility with i-g-t Signed-off-by:
David Herrmann <dh.herrmann@gmail.com> Reviewed-by:
Chris Wilson <chris@chris-wilson.co.uk> Signed-off-by:
Dave Airlie <airlied@redhat.com> [bwh: Backported to 3.2: - drm_framebuffer_funcs::create_handle must be non-null - Adjust context, indentation] Signed-off-by:
-
Martin Schwidefsky authored
commit 8adbf78e upstream. Git commit 4f37a68c "s390: Use direct ktime path for s390 clockevent device" makes use of the CLOCK_EVT_FEAT_KTIME clockevent option to avoid the delta calculation with ktime_get() in clockevents_program_event and the get_tod_clock() in s390_next_event. This is based on the assumption that the difference between the internal ktime and the hardware clock is reflected in the wall_to_monotonic delta. But this is not true, the ntp corrections are applied via changes to the tk->mult multiplier and this is not reflected in wall_to_monotonic. In theory this could be solved by using the raw monotonic clock but it is simpler to switch back to the standard clock delta calculation. Signed-off-by:
Martin Schwidefsky <schwidefsky@de.ibm.com> [bwh: Backported to 3.2: s/get_tod_clock()/get_clock()/] Signed-off-by:
-
Anatol Pomozov authored
commit c9b92530 upstream. Instead of checking whether the handle is valid, we check if journal is enabled. This avoids taking the s_orphan_lock mutex in all cases when there is no journal in use, including the error paths where ext4_orphan_del() is called with a handle set to NULL. Signed-off-by:
Anatol Pomozov <anatol.pomozov@gmail.com> Signed-off-by:
"Theodore Ts'o" <tytso@mit.edu> [bwh: Adjust context to apply after commit 0e9a9a1a ('ext4: avoid hang when mounting non-journal filesystems with orphan list') and commit e2bfb088 ('ext4: don't orphan or truncate the boot loader inode')] Signed-off-by:
-
Al Viro authored
commit ca5358ef upstream. ... by not hitting rename_retry for reasons other than rename having happened. In other words, do _not_ restart when finding that between unlocking the child and locking the parent the former got into __dentry_kill(). Skip the killed siblings instead... Signed-off-by:
Al Viro <viro@zeniv.linux.org.uk> [bwh: Backported to 3.2: - As we only have try_to_ascend() and not d_walk(), apply this change to all callers of try_to_ascend() - Adjust context to make __dentry_kill() apply to d_kill()] Signed-off-by:
-
Al Viro authored
commit 946e51f2 upstream. Signed-off-by:
-
