In MMP2, clock tick rate should be 6500000.
Signed-off-by: Mingliang Hu <mhu4@marvell.com>
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

In mmp2, 6 banks of GPIO registers are supported. So we can support 192
GPIO pins at most.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Enable MAX8649 & MAX8925 regulator, dynamic debug, Marvell Jasper platform.
Disable DNOTIFY, MAX8660 regulator, 88pm860x PMIC.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Enable Tauros2 L2 in mmp2. Tauros2 L2 is shared in Marvell ARM cores.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Use clk_add_table in order to sync with clock driver.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

delay_detect in HZ is confusing, convert it to be millisecond based. And
thus remove those unnecessary call to msecs_to_jiffies() at runtime for
this field. Other constants are converted assuming HZ == 100, which are
basically true for those platforms.

The assignment in csb726.c was incorrect, and is fixed in this patch as
a result.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>
Acked-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Marc Zyngier <maz@misterjones.org>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Acked-by: Mike Rapoport <mike@compulab.co.il>
Acked-by: Daniel Mack <daniel@caiaq.de>

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

This patch removes write to UP2OCR[DMSTATE] (ex-UP2OCR_DPPUBE) which is invalid
on PXA270C5 and later.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

The touchscreen GPIO IRQ was used as a magic number. Define it properly in the
board header file. This is a simple cleanup patch.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

This patch adds support for the on-board IDE channel. I tested this with a CDROM
connected over 2.5-3.5 IDE reduction with external power supplied to the CDROM.
This was not tested with the Voipac 270-HDD-000 (official Voipac HDD module),
but I expect no problems.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

This adds support for the UCB1400 touchscreen found in the VPAC270 device.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

NOTE:
I wasn't able to get it running without reseting the HXOE (so it's there based
on my tests with the hardware). I'll have to investigate it properly when I have
more time.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Reviewed-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

PCMCIA support for Voipac PXA270
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

This patch adds basic support for the Voipac PXA270 SBC.
The device consists of the following hardware:
- PXA270 @ 520 MHz
- 256MB RAM (sparsemem, 2*128MB regions)
- 64MB NOR flash
- 640x480 LCD
- Ports: 2xUHC, 1xUDC, 1xPCMCIA, VGA, FFUART, 2xPS2, Speaker, MIC
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

This patch adds support for the Zipit Z2. The parts missing from this
patch are the battery support, SPI driver for the LCD and support for
the Silicon Serial ID chip.
Signed-off-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

CM-X300 bootloader passes DRAM configuration information in ATAGS,
however, the first memory bank is reported at actual physical address 0x8000000.
Use the configuration information supplied by the bootloader and
cope with the necessity to have PHYS_ADDR=0xa0000000.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Mike Rapoport <mike@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Tosa is now able to use generic matrix keypad driver instead of the deprecated
tosakbd.c, where CONFIG_KEYBOARD_TOSA_USE_EXT_KEYCODES is still useful.  Move
it to mach/Kconfig.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

REVISIT: change to GPIO18 is ugly, need to make sure whether that's
really necessary - GPIO18_RDY as an VLIO input signal - we don't
normally need to do such kind of trick during low power mode.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Some pins are expected to keep their last level during suspend, and
introduce MFP_LPM_KEEP_OUTPUT for this.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

The assignments of res to the results of the two calls to
platform_get_resource make it impossible to use res in the error handling
code in the arguments to release_mem_region.

The semantic match that finds the former problem is as follows:
(http://coccinelle.lip6.fr/)

// <smpl>
@r exists@
expression E, E1;
identifier f;
statement S1,S3;
iterator iter;
@@

if ((E == NULL && ...) || ...)
{
 ... when != false ((E == NULL && ...) || ...)
     when != true  ((E != NULL && ...) || ...)
     when != iter(E,...) S1
     when != E = E1
(
 sizeof(E->f)
|
* E->f
)
 ... when any
 return ...;
}
else S3
// </smpl>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Configure both ssp and wm8753 in aspenite.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Support ssp devices in PXA168. PXA168 could reuse the code of PXA SSP.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Try to keep minimum ifdef in ssp.h.  Some of the definitions are valid
only to specific SoCs, and device drivers should be responsible to take
care of these difference.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

PXA_SSP is actually used by drivers like drivers/spi/pxa2xx_spi.c and
sound/soc/pxa/pxa-ssp.c, not by boards. Remove those incorrect 'select'
from Kconfig and make SOC_PXA_SSP to select.
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Eric Miao <eric.y.miao@gmail.com>

Signed-off-by: Eric Miao <eric.y.miao@gmail.com>