Add support for setting the RX and TX ring sizes for this driver using
ethtool. Also increase the default RX ring size as the previous default
was far too low for good performance in some configurations.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

The Xilinx DMA blocks each have their own reset register, but they both
reset the entire DMA engine, so only one of them needs to be reset.

Also, when stopping the device, we need to not just command the DMA
blocks to stop, but wait for them to stop, and trigger a device reset
to ensure that they are completely stopped.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MDIO clock divisor register setting was only applied on the initial
startup when the driver was loaded. However, this setting is cleared
when the device is reset, such as would occur when the interface was
taken down and brought up again, and so the MDIO bus would be
non-functional afterwards.

Split up the MDIO bus setup and enable into separate functions and
re-enable the bus after a device reset, to ensure that the MDIO
registers are set properly. This also allows us to remove direct access
to MDIO registers in xilinx_axienet_main.c and centralize them all in
xilinx_axienet_mdio.c.

Also, lock the MDIO bus lock around the device reset process, to avoid
MDIO accesses from occurring while the MDIO is disabled during the reset.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since the MDIO is is brought up before the netdev is registered, it
should be torn down after the netdev is removed. Otherwise, PHY accesses
can potentially access freed MDIO bus references and cause a crash.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

This driver was previously always calculating the MDIO clock divisor
(from AXI bus clock to MDIO bus clock) based on the CPU clock frequency,
assuming that it is the same as the AXI bus frequency, but that
simplistic method only works on the MicroBlaze platform.

Add support for specifying the clock used for the device in the device
tree using the clock framework. If the clock is specified then it will
be used when calculating the clock divisor. The previous CPU clock
detection method is left for backward compatibility if no clock is
specified.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

This driver should now build on (at least) X86 and ARM platforms, so add
them as supported platforms for the driver in Kconfig.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

The MDIO bus for this driver was being named using the result of
of_address_to_resource on a node which may not have any resource on it,
but the return value of that call was not checked so it was using some
random value in the bus name. Change to name the MDIO bus based on the
resource start of the actual Ethernet register block.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

This driver was using in_be32 and out_be32 IO accessors which do not
exist on most platforms. Also, the use of big-endian accessors does not
seem correct as this hardware is accessed over an AXI bus which, to the
extent it has an endian-ness, is little-endian. Switch to standard
ioread32/iowrite32 accessors.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

This driver was casting skb pointers to u32 and storing them as such in
the DMA buffer descriptor, which is obviously broken on 64-bit. The area
of the buffer descriptor being used is not accessed by the hardware and
has sufficient room for a 32 or 64-bit pointer, so just store the skb
pointer as such.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

On the Arria10, Agilex, and Stratix10 SoC, there are a few differences from
the Cyclone5 and Arria5:
 - The emac PHY setup bits are in separate registers.
 - The PTP reference clock select mask is different.
 - The register to enable the emac signal from FPGA is different.

Thus, this patch creates a separate function for setting the phy modes on
Arria10/Agilex/Stratix10. The separation is based a new DTS binding:
"altr,socfpga-stmmac-a10-s10".
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add the "altr,socfpga-stmmac-a10-s10" binding for Arria10/Agilex/Stratix10
implementation of the stmmac ethernet controller.

On the Arria10, Agilex, and Stratix10 SoCs, there are a few differences from
the Cyclone5 and Arria5:
     - The emac PHY setup bits are in separate registers.
     - The PTP reference clock select mask is different.
     - The register to enable the emac signal from FPGA is different.

Because of these differences, the dwmac-socfpga glue logic driver will
use this new binding to set the appropriate bits for PHY, PTP reference
clock, and signal from FPGA.
Signed-off-by: Dinh Nguyen <dinguyen@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Jakub Kicinski says:

====================
nfp: tls: add basic TX offload

This series adds initial TLS offload support to the nfp driver.
Only TX side is added for now.  We need minor adjustments to
the core tls code:
 - expose the per-skb fallback helper;
 - grow the driver context slightly;
 - add a helper to get to the driver state more easily.
We only support TX offload for now, and only if all packets
keep coming in order.  For retransmissions we use the
aforementioned software fallback, and in case there are
local drops we completely give up on given TCP stream.

This will obviously be improved soon, this patch set is the
minimal, functional yet easily reviewable chunk.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Count TX TLS packets: successes, out of order, and dropped due to
missing record info.  Make sure the RX and TX completion statistics
don't share cache lines with TX ones as much as possible.  With TLS
stats they are no longer reasonably aligned.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

This patch adds the functionality to add and delete TLS connections on
the NFP, received from the kernel TLS callbacks.

Make use of the common control message (CCM) infrastructure to propagate
the kernel state to firmware.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Prepend connection handle to each transmitted TLS packet.

For each connection, the driver tracks the next sequence number
expected. If an out of order packet is observed, the driver calls into
the TLS kernel code to reencrypt that particular skb.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

While offloading TLS connections, drivers need to handle the case where
out of order packets need to be transmitted.

Other drivers obtain the entire TLS record for the specific skb to
provide as context to hardware for encryption. However, other designs
may also want to keep the hardware state intact and perform the
out of order encryption entirely on the host.

To achieve this, export the already existing software encryption
fallback path so drivers could access this.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently drivers have to ensure the alignment of their tls state
structure, which leads to unnecessary layers of getters and
encapsulated structures in each driver.

Simplify all this by marking the driver state as aligned (driver_state
members are currently aligned, so no hole is added, besides ALIGN in
TLS_OFFLOAD_CONTEXT_SIZE_RX/TX would reserve this extra space, anyway.)
With that we can add a common accessor to the core.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

8 bytes of driver state has been enough so far, but for drivers
which have to store 8 byte handle it's no longer practical to
store the state directly in the context.

Drivers generally don't need much extra state on RX side, while
TX side has to be tracking TCP sequence numbers.  Split the
lengths of max driver state size on RX and TX.

The struct tls_offload_context_tx currently stands at 616 bytes and
struct tls_offload_context_rx stands at 368 bytes.  Upcoming work
will consume extra 8 bytes in both for kernel-driven resync.
This means that we can bump TX side to 16 bytes and still fit
into the same number of cache lines but on RX side we would be 8
bytes over.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Subsequent patches will add support for more TX metadata fields.
Prepare for this by handling an additional double word - firmware
handle as metadata type 7.
Signed-off-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add FW ABI defines and code for basic init of TLS offload.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Parse TLV containing a bitmask of supported crypto operations.
The TLV contains a capability bitmask (supported operations)
and enabled bitmask.  Each operation describes the crypto
protocol quite exhaustively (protocol, AEAD, direction).
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

FW may prefer to handle some communication via a mailbox
or the vNIC may simply not have a control queue (VFs).
Add a way of exchanging ccm-compatible messages via a
mailbox.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Parse the mailbox TLV.  When control message queue is not available
we can fall back to passing the control messages via the vNIC
mailbox.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

We will need to release the bar lock from a workqueue
so move from a mutex to a semaphore.  This lock should
not be too hot.  Unfortunately semaphores don't have
lockdep support.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Currently if we need to modify the head of the skb and allocation
fails we would free the skb and not increment the error counter.
Make sure all errors are counted.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Add 1000BaseX to the link modes which are detected based on the
MII_ESTATUS register as per 802.3 Clause 22. This allows PHYs which
support 1000BaseX to work properly with drivers using phylink.

Previously 1000BaseX support was not detected, and if that was the only
mode the PHY indicated support for, phylink would refuse to attach it
due to the list of supported modes being empty.
Signed-off-by: Robert Hancock <hancock@sedsystems.ca>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix sparse warning:

drivers/net/ethernet/mscc/ocelot_ace.c:96:3:
 warning: symbol 'vcap_data_t' was not declared. Should it be static?

'vcap_data_t' never used so can be removed
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When a valid MAC address is not found the current messages
are shown:

fec 2188000.ethernet (unnamed net_device) (uninitialized): Invalid MAC address: 00:00:00:00:00:00
fec 2188000.ethernet (unnamed net_device) (uninitialized): Using random MAC address: aa:9f:25:eb:7e:aa

Since the network device has not been registered at this point, it is better
to use dev_err()/dev_info() instead, which will provide cleaner log
messages like these:

fec 2188000.ethernet: Invalid MAC address: 00:00:00:00:00:00
fec 2188000.ethernet: Using random MAC address: aa:9f:25:eb:7e:aa

Tested on a imx6dl-pico-pi board.
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The monolithic hash_lock could cause huge contention when
inserting/deletiing vxlan_fdbs into the fdb_head.

Use FDB_HASH_SIZE hash_locks to protect insertions/deletions
of vxlan_fdbs into the fdb_head hash table.
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Litao jiao <jiaolitao@raisecom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

There is a spelling mistake in a NL_SET_ERR_MSG message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The opts[] array is of type u32. Therefore remove the wrong
cpu_to_le32(). The opts[] array members are converted to little endian
later when being assigned to the respective descriptor fields.

This is not a new issue, it just popped up due to r8169.c having
been renamed and more thoroughly checked. Due to the renaming
this patch applies to net-next only.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Eric Dumazet says:

====================
ipv6: tcp: more control on RST flowlabels

First patch allows to reflect incoming IPv6 flowlabel
on RST packets sent when no socket could handle the packet.

Second patch makes sure we send the same flowlabel
for RST or ACK packets on behalf of TIME_WAIT sockets.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

After commit 1d13a96c ("ipv6: tcp: fix flowlabel value in ACK
messages"), we stored in tw_flowlabel the flowlabel, in the
case ACK packets needed to be sent on behalf of a TIME_WAIT socket.

We can use the same field so that RST packets sent from
TIME_WAIT state also use a consistent flowlabel.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Florent Fourcot <florent.fourcot@wifirst.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>

When RST packets are sent because no socket could be found,
it makes sense to use flowlabel_reflect sysctl to decide
if a reflection of the flowlabel is requested.

This extends commit 22b6722b ("ipv6: Add sysctl for per
namespace flow label reflection"), for some TCP RST packets.

In order to provide full control of this new feature,
flowlabel_reflect becomes a bitmask.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:

struct objagg_stats {
	...
        struct objagg_obj_stats_info stats_info[];
};

size = sizeof(*objagg_stats) + sizeof(objagg_stats->stats_info[0]) * count;
instance = kzalloc(size, GFP_KERNEL);

Instead of leaving these open-coded and prone to type mistakes, we can
now use the new struct_size() helper:

instance = kzalloc(struct_size(instance, stats_info, count), GFP_KERNEL);

Notice that, in this case, variable alloc_size is not necessary, hence it
is removed.

This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

small cleanup: "struct request_sock_queue *queue" parameter of reqsk_queue_unlink
func is never used in the func, so we can remove it.
Signed-off-by: Zhiqiang Liu <liuzhiqiang26@huawei.com>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the early days of phylib we had a functionality that changed to the
next lower speed in fixed mode if no link was established after a
certain period of time. This functionality has been removed years ago,
and state PHY_FORCING isn't needed any longer. Instead we can go from
UP to RUNNING or NOLINK directly (same as in autoneg mode).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The variable cache_allocs is to indicate how many frags (KiB) are in one
rds connection frag cache.
The command "rds-info -Iv" will output the rds connection cache
statistics as below:
"
RDS IB Connections:
      LocalAddr RemoteAddr Tos SL  LocalDev            RemoteDev
      1.1.1.14 1.1.1.14   58 255  fe80::2:c903:a:7a31 fe80::2:c903:a:7a31
      send_wr=256, recv_wr=1024, send_sge=8, rdma_mr_max=4096,
      rdma_mr_size=257, cache_allocs=12
"
This means that there are about 12KiB frag in this rds connection frag
cache.
Since rds.h in rds-tools is not related with the kernel rds.h, the change
in kernel rds.h does not affect rds-tools.
rds-info in rds-tools 2.0.5 and 2.0.6 is tested with this commit. It works
well.
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Biao Huang says:

====================
complete dwmac-mediatek driver and fix flow control issue

Changes in v2:
        patch#1: there is no extra action in mediatek_dwmac_remove, remove it

v1:
This series mainly complete dwmac-mediatek driver:
        1. add power on/off operations for dwmac-mediatek.
        2. disable rx watchdog to reduce rx path reponding time.
        3. change the default value of tx-frames from 25 to 1, so
           ptp4l will test pass by default.

and also fix the issue that flow control won't be disabled any more
once being enabled.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>

Current dwmac4_flow_ctrl will not clear
GMAC_RX_FLOW_CTRL_RFE/GMAC_RX_FLOW_CTRL_RFE bits,
so MAC hw will keep flow control on although expecting
flow control off by ethtool. Add codes to fix it.

Fixes: 477286b5 ("stmmac: add GMAC4 core support")
Signed-off-by: Biao Huang <biao.huang@mediatek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>