- 07 Mar, 2016 30 commits
-
-
Xinming Hu authored
This patch sdio multi port aggregation statistics which can be used for debugging. This debug data is collected in /sys/kernel/debug/mwifiex/mlan0/debug. Signed-off-by:
Xinming Hu <huxm@marvell.com> Signed-off-by:
Cathy Luo <cluo@marvell.com> Signed-off-by:
Amitkumar Karwar <akarwar@marvell.com> Signed-off-by:
Kalle Valo <kvalo@codeaurora.org>
-
Amitkumar Karwar authored
This patch corrects the error case in association path by returning -1. Earlier "media_connected" used to remain on in this error case causing failure for further association attempts. Signed-off-by:
-
Xinming Hu authored
It is observed that driver may send the data packet to tdls peer before tdls peer receives tdls setup confirm frame. Similar race condition exists during tdls teardown procedure also. This patch adds 10 milliseconds delay to resolve the race. Signed-off-by:
-
Colin Ian King authored
passing rtl_stats by value is inefficient; the structure is over 300 bytes in size and generally just one field (packet_report_type) is being accessed, so the pass by value is a relatively large overhead. This change just affects just the rx_command_packet calls. Signed-off-by:
Colin Ian King <colin.king@canonical.com> Acked-by:
Larry Finger <Larry.Finger@lwfinger.net> Signed-off-by:
-
Alexey Khoroshilov authored
There is no need in usb_put_dev() if at76_load_internal_fw() succeed. Found by Linux Driver Verification project (linuxtesting.org). Signed-off-by:
Alexey Khoroshilov <khoroshilov@ispras.ru> Signed-off-by:
-
Amitoj Kaur Chawla authored
Introduce the use of to_delayed_work() helper function instead of open coding it with container_of() A simplified version of the Coccinelle semantic patch used to make this change is: //<smpl> @@ expression a; symbol work; @@ - container_of(a, struct delayed_work, work) + to_delayed_work(a) //</smpl> Signed-off-by:
Amitoj Kaur Chawla <amitoj1606@gmail.com> Reviewed-by:
Julian Calaby <julian.calaby@gmail.com> Signed-off-by:
-
Hante Meuleman authored
Add full support for both AP and STA for management frame protection. Reviewed-by:
Arend Van Spriel <arend.van@broadcom.com> Reviewed-by:
Franky (Zhenhui) Lin <franky.lin@broadcom.com> Reviewed-by:
Pieter-Paul Giesberts <pieter-paul.giesberts@broadcom.com> Signed-off-by:
Hante Meuleman <hante.meuleman@broadcom.com> Signed-off-by:
Arend van Spriel <arend@broadcom.com> Signed-off-by:
-
Hante Meuleman authored
brcmf_add_keyext is called when a key is configured for a specific mac address. This function is very similar to the calling function brcmf_add_key. Integrate this function and also use existing del_key function in case key is to be cleared. Reviewed-by:
-
Hante Meuleman authored
Merge module parameters and platform data in one struct. This is the last step to move to the new platform data per device. Now parameters of platform data will be merged with module parameters per device. Reviewed-by:
Franky (Zhenhui) Lin <frankyl@broadcom.com> Reviewed-by:
Pieter-Paul Giesberts <pieterpg@broadcom.com> Signed-off-by:
Hante Meuleman <meuleman@broadcom.com> Signed-off-by:
-
Hante Meuleman authored
Platform data is only available for sdio. With this patch a new platform data structure is being used which allows for platform data for any device and configurable per device. This patch only switches to the new structure and adds support for SDIO devices. Reviewed-by:
-
Hante Meuleman authored
Currently ARP and ND (IPv6 Neigbor Discovery) offload get disabled on entering suspend. However when firmwares support the wowl_cap iovar then these offload routines can be kept enabled as they will work during WOWL as well. Reviewed-by:
-
Hante Meuleman authored
In preparation of module parameters for all devices the module platform data retrieval is moved from sdio to common. It is still only used for sdio devices. Reviewed-by:
-
Hante Meuleman authored
This patch adds support for gtk rekeying offload and for gtk rekeying failure during wowl mode. Reviewed-by:
-
Hante Meuleman authored
In preparation of module parameters for all devices the module init and exit routines are moved to the common file. Reviewed-by:
-
Hante Meuleman authored
When keys get set and updated this has to happen after eapol got transmitted (without key or old key) before the key can be updated. To make sure the order of sending eapol and configuring key is done correctly a timeout for tx of eapol is applied. This timeout is set to 50 msec, which is not always enough. Especially in AP mode and key updates the timeout may need to be much longer because client(s) can be in powersave. Increase the timeout from 50 to 950 msec. Reviewed-by:
-
Hante Meuleman authored
The PCIE bus driver supports older gen1 (v1) chips, but there is no actual device which is using this older pcie core which is supported by brcmfmac. Remove all gen1 related code. Reviewed-by:
-
Hante Meuleman authored
A newer version of the 4366 PCIE chip has been released. Add support for this version of the chip. Reviewed-by:
-
Hante Meuleman authored
The PCIE bar1 window size is specified by chip. Currently the ioremap of bar1 was using a define which always matched the size of bar1, but newer chips can have a different bar1 sizes. With this patch the ioremap will be called with the by chip provided window size. Reviewed-by:
-
Hante Meuleman authored
Newer type pcie devices have memory which get shared between fw and hw. The division of this memory is done firmware compile time. As a result the ramsize as used by driver needs to be adjusted for this. This is done by reading the memory size from the firmware. Reviewed-by:
-
Franky Lin authored
The return value of iovar set function should be saved and checked. Reviewed-by:
-
Franky Lin authored
Configure ipv6 address for neighbor discovery offload ip table in firmware obtained through ipv6 address notification callback. Reviewed-by:
-
Hante Meuleman authored
Add additional length checks on firmware events to create more robust code. Reviewed-by:
Lei Zhang <leizh@broadcom.com> Signed-off-by:
-
Hante Meuleman authored
Country code configuration in a device is a device specific operation. For this the country code as specified by reg notifier (iso3166 alpha2) needs to be translated to a device specific country locale and revision number. This patch adds this translation and puts a placeholder in the device specific settings where the translation table can be stored. Additional patches will be needed to read these tables from for example device platform data. Reviewed-by:
-
Franky Lin authored
In some cases wiphy->wowlan could be NULL if firmware doesn't have the support. Driver should check for support before walking down the feature flags. Reviewed-by:
-
Hante Meuleman authored
Some systems have problems with allocating memory allocation larger then 64K. Often on unload/load or suspend/resume a failure is reported: Could not allocate wiphy device. This patch makes the escan intermediate storage buf dynamically allocated, and smaller than 64K. Reviewed-by:
-
Arend van Spriel authored
Dropping the '_timeout' from the function name as the fact that a timeout value is passed makes it obvious a timeout is used. Also helps to keep code lines a bit shorter and easier to stick to 80 char boundary. Reviewed-by:
-
Larry Finger authored
Routine rtl_addr_delay() uses delay statements in code that can sleep. To improve system responsiveness, the various delay statements are changed. In addition, routines rtl_rfreg_delay() and rtl_bb_delay() are rewritten to use the code in rtl_addr_delay() for most of their input values. Suggested-by:
Byeoungwook Kim <quddnr145@gmail.com> Signed-off-by:
-
Christian Lamparter authored
Import new headers from my firmware branch: <https://github.com/chunkeey/carl9170fw> Signed-off-by:
Christian Lamparter <chunkeey@googlemail.com> Signed-off-by:
-
One Thousand Gnomes authored
The buffer needs to be zero terminated in case the user data is not. Otherwise we run off the end of the buffer. Signed-off-by:
Alan Cox <alan@linux.intel.com> Reviewed-by:
-
Larry Finger authored
When driver rtl8821ae is loaded but not connected to any AP, it logs a "firmware not ready to run" message roughly once a minute. To eliminate logging this massage under normal debug conditions, the degug level needed to print this message is increased. Signed-off-by:
-
- 06 Mar, 2016 2 commits
-
-
Kalle Valo authored
Needed by the upcoming merge of iwlwifi-next-for-kalle-2016-03-02 tag.
-
Kalle Valo authored
ath.git patches for 4.6. Major changes: ath10k * dt: add bindings for ipq4019 wifi block * start adding support for qca4019 chip ath9k * add device ID for Toshiba WLM-20U2/GN-1080 * allow more than one interface on DFS channels
-
- 05 Mar, 2016 5 commits
-
-
David S. Miller authored
Zhang Shengju says: ==================== use reset to set header pointers This patch series replace set function with reset when offset is zero. ==================== Signed-off-by:David S. Miller <davem@davemloft.net>
-
Zhang Shengju authored
Since offset is zero, it's not necessary to use set function. Reset function is straightforward, and will remove the unnecessary add operation in set function. Signed-off-by:
Zhang Shengju <zhangshengju@cmss.chinamobile.com> Signed-off-by:
-
Zhang Shengju authored
Since offset is zero, it's not necessary to use set function. Reset function is straightforward, and will remove the unnecessary add operation in set function. Signed-off-by:
-
Zhang Shengju authored
Since offset is zero, it's not necessary to use set function. Reset function is straightforward, and will remove the unnecessary add operation in set function. Signed-off-by:
-
Zhang Shengju authored
Since offset is zero, it's not necessary to use set function. Reset function is straightforward, and will remove the unnecessary add operation in set function. Signed-off-by:
-
- 04 Mar, 2016 3 commits
-
-
David S. Miller authored
Merge tag 'rxrpc-rewrite-20160304' of git://git.kernel.org/pub/scm/linux/kernel/git/dhowells/linux-fs David Howells says: ==================== RxRPC: Rewrite part 1 Here's the first set of patches from my RxRPC rewrite, aimed at net-next. These do some clean ups and bug fixes. Most of the changes are small, but there are a couple of bigger changes: (*) Convert call flag numbers and event numbers into enums. Then rename the event numbers to all have _EV_ in their name to stop confusion. Fix one instance of an event bit being used instead of a flag bit. (*) A copy of the Rx protocol header is kept in the sk_buff private data. Keep this in host byte order rather than network byte order as it makes more sense. A number of other fields then get converted into host byte order too. Conversion between host and network byte order is then done at the packet reception/generation stage. This is based on net-next/master ==================== Signed-off-by:
-
David S. Miller authored
Nicolas Dichtel says: ==================== uapi: consolidate DIV_ROUND_UP definition The inital goal was to consolidate ethtool.h uapi header. But I took the opportunity to remove all duplicate definitions of DIV_ROUND_UP. v3: add patch #2 and #3 v2: split the patch define DIV_ROUND_UP in uapi ==================== Signed-off-by: -
Nicolas Dichtel authored
INT_MAX needs limits.h in userland. When ethtool.h is included by a userland app, we got the following error: .../usr/include/linux/ethtool.h: In function 'ethtool_validate_speed': .../usr/include/linux/ethtool.h:1471:18: error: 'INT_MAX' undeclared (first use in this function) return speed <= INT_MAX || speed == SPEED_UNKNOWN ^ Fixes: e02564ee ("ethtool: make validate_speed accept all speeds between 0 and INT_MAX") CC: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by:Nicolas Dichtel <nicolas.dichtel@6wind.com> Acked-by:
Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by:
-
