The route_irq() function needs to preserve the irq mask by using the
_irqsave/irqrestore variants of raw spin lock functions instead of the
_irq variants. This is because it is called from __cpu_disable() (via
migrate_irqs()), which is called with IRQs disabled, so using the _irq
variants re-enables IRQs.

This appears to have been causing occasional hits of the
BUG_ON(!irqs_disabled()) in __irq_work_run() during CPU hotplug soak
testing:
  BUG: failure at kernel/irq_work.c:122/__irq_work_run()!
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Srivatsa S. Bhat <srivatsa.bhat@linux.vnet.ibm.com>

kick_handler() doesn't have an irq_enter/exit pair, but it's used for
handling SMP IPIs which require work to be done in softirqs, which are
invoked from irq_exit() when the hard irq nest count reaches 0.

The scheduler_ipi() callback in the IPI handler calls irq_enter/exit
itself, but this is inside kick_handler()'s spin lock critical section,
so if an invoked softirq issues an IPI the kick_handler() will be
re-entered on the same CPU and will deadlock.

This is easily fixed by adding the missing irq_enter/exit to
kick_handler() so that the hard irq nest count doesn't reach 0 until
after the spin lock has been released.

Ideally the spin lock protected handler list will also be replaced by a
lockless RCU protected list since it is certainly mostly read. That can
be done in a later change though.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>

Use a completion to block until a secondary CPU has started up, like ARM
do, instead of a loop of udelays.

On Meta, SMP is really SMT, with each "CPU" being a different hardware
thread on the same Meta processor core, so as well as being more
efficient and latency friendly, using a completion prevents the bogomips
of the secondary CPU from being drastically skewed every time by the
execution of the tight in-cache udelay loop on the other CPU.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: "Srivatsa S. Bhat" <srivatsa.bhat@linux.vnet.ibm.com>

In secondary_start_kernel() interrupts should be enabled with
local_irq_enable() after the cpu is marked as online with
set_cpu_online(). Otherwise it's possible for a timer interrupt to
trigger a softirq, which if the cpu is marked as offline may have it's
affinity altered.
Reported-by: Kirill Tkhai <tkhai@yandex.ru>
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: "Srivatsa S. Bhat" <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Kirill Tkhai <tkhai@yandex.ru>

Checking for process->mm is not enough because process' main thread may
exit or detach its mm via use_mm(), but other threads may still have a
valid mm.

To fix this we would need to use find_lock_task_mm(), which would walk
up all threads and returns an appropriate task (with task lock held).

clear_tasks_mm_cpumask() was introduced in v3.5-rc1 to fix this issue,
so let's use it for metag too.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: "Srivatsa S. Bhat" <srivatsa.bhat@linux.vnet.ibm.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Anton Vorontsov <anton.vorontsov@linaro.org>

Select PINCTRL_TZ1090_PDC from SOC_TZ1090 to enable the PDC pin
controller driver once it is merged, and instantiate it from
tz1090.dtsi.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Grant Likely <grant.likely@linaro.org>

Select PINCTRL and PINCTRL_TZ1090 from SOC_TZ1090 to enable the main pin
controller driver once it is merged, and instantiate it from
tz1090.dtsi.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Grant Likely <grant.likely@linaro.org>

The cache configuration of the boot cpu is now duplicated to secondary
cpus, so there's no need to check for cache aliasing again when a
secondary cpu is booted. Therefore remove the check from
secondary_start_kernel().
Signed-off-by: James Hogan <james.hogan@imgtec.com>

If the cache and page size configuration allows for cache aliasing to
occur we warn on boot, but the log messages are easy to miss and will
result is random crashes occuring in userland. Let's panic too in this
case so that the user immediately knows they need to fix the cache
configuration or configured page size.

Also fix the warning messages which display the cache and page sizes to
include newlines, and add the word "Potential" since an actual cache
alias hasn't been detected.
Signed-off-by: James Hogan <james.hogan@imgtec.com>

Include *.dtsi files from *.dts using the preprocessor to set a good
example for future device tree files. Files included in the old way
don't get pre-processed.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Cc: devicetree-discuss@lists.ozlabs.org

Add symlink to include/dt-bindings from arch/metag/boot/dts/include/ to
match the one in arch/arm/... (see the commit below) so that
preprocessed device tree files can include various useful constant
definitions.

Commit c58299aa ("kbuild: create an
"include chroot" for DT bindings") merged in v3.10-rc1.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Acked-by: Grant Likely <grant.likely@linaro.org>
Reviewed-by: Stephen Warren <swarren@nvidia.com>
Cc: Michal Marek <mmarek@suse.cz>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: linux-kbuild@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org

The .SECONDARY rule for generating the *.dtb.S files added in
0b4184c2
"metag: avoid unnecessary builtin dtb rebuilds"
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>

Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>

Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>

Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>

Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>

Hide symbol since it's only used within the cache.c file
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>

Fixes the following sparce warning:

warning: symbol 'init_IRQ' was not declared. Should it be static?
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>

It is only referenced within the irq.c file, so restrict it's scope
as appropriate.
Signed-off-by: Markos Chandras <markos.chandras@imgtec.com>
Signed-off-by: James Hogan <james.hogan@imgtec.com>

Log core clock and Meta timer frequencies during init in architecture
generic code, removing the need for equivalent log messages in SoC
specific code.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: John Stultz <john.stultz@linaro.org>
Cc: Thomas Gleixner <tglx@linutronix.de>

If the common clock framework is enabled, call of_clk_init(NULL) in
time_init() to register device tree clocks with the clock framework.

After this time_init() calls a new function init_metag_clocks(), which
looks for a clock named "core" in the node compatible with "img,meta"
(usually the root node). If found the get_core_freq machine callback is
overridden to obtain the core clock frequency using that clock.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Grant Likely <grant.likely@linaro.org>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: devicetree-discuss@lists.ozlabs.org

Add really minimal support for Toumaz Xenif TZ1090 SoC (A.K.A. Comet).
This consists of minimal build infrastructure, device tree files, and a
defconfig based on meta2_defconfig.

This SoC contains a 2-threaded HTP (Meta 2) as the main application
processor, and is found in a number of development boards and digital
radios, such as the Minimorph Development Platform.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Rob Landley <rob@landley.net>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-doc@vger.kernel.org
Cc: devicetree-discuss@lists.ozlabs.org

If no init_machine callback is provided, call of_platform_populate()
instead. This allows a board/SoC that only needs to call
of_platform_populate to omit the callback altogether.
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: Grant Likely <grant.likely@secretlab.ca>
Cc: Rob Herring <rob.herring@calxeda.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: devicetree-discuss@lists.ozlabs.org

This patch fixes warnings due to missing lock on write error path.

  WARNING: at fs/hpfs/hpfs_fn.h:353 hpfs_truncate+0x75/0x80 [hpfs]()
  Hardware name: empty
  Pid: 26563, comm: dd Tainted: P           O 3.9.4 #12
  Call Trace:
    hpfs_truncate+0x75/0x80 [hpfs]
    hpfs_write_begin+0x84/0x90 [hpfs]
    _hpfs_bmap+0x10/0x10 [hpfs]
    generic_file_buffered_write+0x121/0x2c0
    __generic_file_aio_write+0x1c7/0x3f0
    generic_file_aio_write+0x7c/0x100
    do_sync_write+0x98/0xd0
    hpfs_file_write+0xd/0x50 [hpfs]
    vfs_write+0xa2/0x160
    sys_write+0x51/0xa0
    page_fault+0x22/0x30
    system_call_fastpath+0x1a/0x1f
Signed-off-by: Mikulas Patocka <mikulas@artax.karlin.mff.cuni.cz>
Cc: stable@kernel.org  # 2.6.39+
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Pull timer fixes from Thomas Gleixner:

 - Trivial: unused variable removal

 - Posix-timers: Add the clock ID to the new proc interface to make it
   useful.  The interface is new and should be functional when we reach
   the final 3.10 release.

 - Cure a false positive warning in the tick code introduced by the
   overhaul in 3.10

 - Fix for a persistent clock detection regression introduced in this
   cycle

* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
  timekeeping: Correct run-time detection of persistent_clock.
  ntp: Remove unused variable flags in __hardpps
  posix-timers: Show clock ID in proc file
  tick: Cure broadcast false positive pending bit warning

Pull irqdomain bug fixes from Grant Likely:
 "This branch contains a set of straight forward bug fixes to the
  irqdomain code and to a couple of drivers that make use of it."

* tag 'irqdomain-for-linus' of git://git.secretlab.ca/git/linux:
  irqchip: Return -EPERM for reserved IRQs
  irqdomain: document the simple domain first_irq
  kernel/irq/irqdomain.c: before use 'irq_data', need check it whether valid.
  irqdomain: export irq_domain_add_simple

The irqdomain core will report a log message for any attempted map call
that fails unless the error code is -EPERM. This patch changes the
Versatile irq controller drivers to use -EPERM because it is normal for
a subset of the IRQ inputs to be marked as reserved on the various
Versatile platforms.
Signed-off-by: Grant Likely <grant.likely@linaro.org>

The first_irq needs to be zero to get a linear domain and that
comes with special semantics. We want to simplify this going
forward but some documentation never hurts.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Grant Likely <grant.likely@linaro.org>

Since irq_data may be NULL, if so, we WARN_ON(), and continue, 'hwirq'
which related with 'irq_data' has to initialize later, or it will cause
issue.
Signed-off-by: Chen Gang <gang.chen@asianux.com>
Signed-off-by: Grant Likely <grant.likely@linaro.org>

All other irq_domain_add_* functions are exported already, and apparently
this one got left out by mistake, which causes build errors for ARM
allmodconfig kernels:

ERROR: "irq_domain_add_simple" [drivers/gpio/gpio-rcar.ko] undefined!
ERROR: "irq_domain_add_simple" [drivers/gpio/gpio-em.ko] undefined!
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Grant Likely <grant.likely@linaro.org>

Pull ARM SoC fixes from Olof Johansson:
 "Another week, another batch of fixes for arm-soc platforms.

  Nothing controversial here, a handful of fixes for regressions and/or
  serious problems across several of the platforms.  Things are slowing
  down nicely on fix rates for 3.10"

* tag 'fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
  ARM: exynos: add debug_ll_io_init() call in exynos_init_io()
  ARM: EXYNOS: uncompress - print debug messages if DEBUG_LL is defined
  ARM: shmobile: sh73a0: Update CMT clockevent rating to 80
  sh-pfc: r8a7779: Don't group USB OVC and PENC pins
  ARM: mxs: icoll: Fix interrupts gpio bank 0
  ARM: imx: clk-imx6q: AXI clock select index is incorrect
  ARM: bcm2835: override the HW UART periphid
  ARM: mvebu: Fix bug in coherency fabric low level init function
  ARM: Kirkwood: TS219: Fix crash by double PCIe instantiation
  ARM: ux500: Provide supplies for AUX1, AUX2 and AUX3
  ARM: ux500: Only configure wake-up reasons on ux500 based platforms
  ARM: dts: imx: fix clocks for cspi
  ARM i.MX6q: fix for ldb_di_sels

Pull MIPS fixes from Ralf Baechle:
 "MIPS fixes across the field.  The only area that's standing out is the
  exception handling which received it's dose of breakage as part of the
  microMIPS patchset"

* 'upstream' of git://git.linux-mips.org/pub/scm/ralf/upstream-linus:
  MIPS: ralink: add missing SZ_1M multiplier
  MIPS: Compat: Fix cputime_to_timeval() arguments in compat binfmt_elf.
  MIPS: OCTEON: Improve _machine_halt implementation.
  MIPS: rtlx: Fix implicit declaration of function set_vi_handler()
  MIPS: Trap exception handling fixes
  MIPS: Quit exposing Kconfig symbols in uapi headers.
  MIPS: Remove duplicate definition of check_for_high_segbits.

Pull m68knommu fix from Greg Ungerer:
 "A single fix for compilation breakage to many of the ColdFire CPU
  targets"

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/gerg/m68knommu:
  m68k: only use local gpio_request_one if not using GPIOLIB

Pull drm fixes from Dave Airlie:
 "Regression fixers for the big 3:

   - nouveau: hdmi audio, dac load detect, s/r regressions fixed
   - radeon: long standing system hang fixed, hdmi audio and rs780 fast
     fb fixes
   - intel: one old regression, a WARN removal, and a stop X dying fix

  Otherwise one mgag200 fix, a couple of arm build fixes, and a core use
  after free fix."

* 'drm-fixes' of git://people.freedesktop.org/~airlied/linux:
  drm/nv50/kms: use dac loadval from vbios, where it's available
  drm/nv50/disp: force dac power state during load detect
  drm/nv50-nv84/fifo: fix resume regression introduced by playlist race fix
  drm/nv84/disp: Fix HDMI audio regression
  drm/i915/sdvo: Use &intel_sdvo->ddc instead of intel_sdvo->i2c for DDC.
  drm/radeon: don't allow audio on DCE6
  drm/radeon: Use direct mapping for fast fb access on RS780/RS880 (v2)
  radeon: Fix system hang issue when using KMS with older cards
  drm/i915: no lvds quirk for hp t5740
  drm/i915: Quirk the pipe A quirk in the modeset state checker
  drm/i915: Fix spurious -EIO/SIGBUS on wedged gpus
  drm/mgag200: Add missing write to index before accessing data register
  drm/nouveau: use mdelay instead of large udelay constants
  drm/tilcd: select BACKLIGHT_LCD_SUPPORT
  drm: fix a use-after-free when GPU acceleration disabled

Pull slave-dmaengine fixes from Vinod Koul:
 "Fix from Andy is for dmatest regression reported by Will and Rabin has
  fixed runtime ref counting for st_dma40"

* 'fixes' of git://git.infradead.org/users/vkoul/slave-dma:
  dmatest: do not allow to interrupt ongoing tests
  dmaengine: ste_dma40: fix pm runtime ref counting

Merge tag 'trace-fixes-v3.10-rc3-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace

Pull tracing fixes from Steven Rostedt:
 "This contains 4 fixes.

  The first two fix the case where full RCU debugging is enabled,
  enabling function tracing causes a live lock of the system.  This is
  due to the added debug checks in rcu_dereference_raw() that is used by
  the function tracer.  These checks are also traced by the function
  tracer as well as cause enough overhead to the function tracer to slow
  down the system enough that the time to finish an interrupt can take
  longer than when the next interrupt is triggered, causing a live lock
  from the timer interrupt.

  Talking this over with Paul McKenney, we came up with a fix that adds
  a new rcu_dereference_raw_notrace() that does not perform these added
  checks, and let the function tracer use that.

  The third commit fixes a failed compile when branch tracing is
  enabled, due to the conversion of the trace_test_buffer() selftest
  that the branch trace wasn't converted for.

  The forth patch fixes a bug caught by the RCU lockdep code where a
  rcu_read_lock() is performed when rcu is disabled (either going to or
  from idle, or user space).  This happened on the irqsoff tracer as it
  calls task_uid().  The fix here was to use current_uid() when possible
  that doesn't use rcu locking.  Which luckily, is always used when
  irqsoff calls this code."

* tag 'trace-fixes-v3.10-rc3-v3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace:
  tracing: Use current_uid() for critical time tracing
  tracing: Fix bad parameter passed in branch selftest
  ftrace: Use the rcu _notrace variants for rcu_dereference_raw() and friends
  rcu: Add _notrace variation of rcu_dereference_raw() and hlist_for_each_entry_rcu()

Commit 9f29ab11 ("ACPI / scan: do not match drivers against objects
having scan handlers") introduced a boot regression on Tony's ia64 HP
rx2600.  Tony says:

  "It panics with the message:

   Kernel panic - not syncing: Unable to find SBA IOMMU: Try a generic or DIG kernel

   [...] my problem comes from arch/ia64/hp/common/sba_iommu.c
   where the code in sba_init() says:

        acpi_bus_register_driver(&acpi_sba_ioc_driver);
        if (!ioc_list) {

   but because of this change we never managed to call ioc_init()
   so ioc_list doesn't get set up, and we die."

Revert it to avoid this breakage and we'll fix the problem it attempted
to address later.
Reported-by: Tony Luck <tony.luck@gmail.com>
Cc: 3.9+ <stable@vger.kernel.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

From Shawn Guo, mxs fixes for 3.10:

- Since the time we move to MULTI_IRQ_HANDLER, the 0x7f polling for no
  interrupt in icoll_handle_irq() becomes insane, because 0x7f is an
  valid interrupt number, the irq of gpio bank 0.  That unnecessary
  polling results in the driver not detecting when irq 0x7f is active
  which makes the machine effectively dead lock.  The fix removes the
  interrupt poll loop and allows usage of gpio0 interrupt without an
  infinite loop.

* tag 'mxs-fixes-3.10' of git://git.linaro.org/people/shawnguo/linux-2.6:
  ARM: mxs: icoll: Fix interrupts gpio bank 0
Signed-off-by: Olof Johansson <olof@lixom.net>

From Shawn Guo, imx fixes for 3.10, take 2:

- One device tree fix for all spi node to have per clock added.
  The clock is needed by spi driver to calculate bit rate divisor.
  The spi node in the current device trees either does not have the
  clock or is defined as dummy clock, in which case the driver probe
  will fail or spi will run at a wrong bit rate.

- Two imx6q clock fixes, which correct axi_sels and ldb_di_sels.

* tag 'imx-fixes-3.10-2' of git://git.linaro.org/people/shawnguo/linux-2.6:
  ARM: imx: clk-imx6q: AXI clock select index is incorrect
  ARM: dts: imx: fix clocks for cspi
  ARM i.MX6q: fix for ldb_di_sels
Signed-off-by: Olof Johansson <olof@lixom.net>