Currently, the md layer checks in analyze_sbs() if the raid level
supports reconstruction (mddev->level >= 1) and if reconstruction is
in progress (mddev->recovery_cp != MaxSector).

Move that printk into the personality code of those raid levels that
care (levels 1, 4, 5, 6, 10).
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>

The difference between these two methods is artificial.
Both check that a pending reshape is valid, and perform any
aspect of it that can be done immediately.
'reconfig' handles chunk size and layout.
'check_reshape' handles raid_disks.

So make them just one method.
Signed-off-by: NeilBrown <neilb@suse.de>

Passing the new layout and chunksize as args is not necessary as
the mddev has fields for new_check and new_layout.

This is preparation for combining the check_reshape and reconfig
methods
Signed-off-by: NeilBrown <neilb@suse.de>

In reshape cases that do not change the number of devices,
start_reshape is called without first calling check_reshape.

Currently, the check that the stripe_cache is large enough is
only done in check_reshape.  It should be in start_reshape too.
Signed-off-by: NeilBrown <neilb@suse.de>

following the conversion to chunk_sectors, there is room
for cleaning up a little.
Signed-off-by: NeilBrown <neilb@suse.de>

1/ Raid5 has learned to take over also raid4 and raid6 arrays.
2/ new_chunk in mdp_superblock_1 is in sectors, not bytes.
Signed-off-by: NeilBrown <neilb@suse.de>

Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>

This kills some more shifts.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>

A straight-forward conversion which gets rid of some
multiplications/divisions/shifts. The patch also introduces a couple
of new ones, most of which are due to conf->chunk_size still being
represented in bytes. This will be cleaned up in subsequent patches.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>

This patch renames the chunk_size field to chunk_sectors with the
implied change of semantics.  Since

	is_power_of_2(chunk_size) = is_power_of_2(chunk_sectors << 9)
				  = is_power_of_2(chunk_sectors)

these bits don't need an adjustment for the shift.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>

Maintain two flows, one for pow2 chunk sizes (which uses masks and
shift), and a flow for the general case (which uses sector_div).
This is for the sake of performance.

 - introduce map_sector and is_io_in_chunk_boundary to encapsulate
   those two flows better for raid0_make_request
 - fix blk_mergeable to support the two flows.

Signed-off-by: raziebe@gmail.com
Signed-off-by: NeilBrown <neilb@suse.de>

Remove chunk size check from md as this is now performed in the run
function in each personality.

Replace chunk size power 2 code calculations by a regular division.

Signed-off-by: raziebe@gmail.com
Signed-off-by: NeilBrown <neilb@suse.de>

have raid5 check chunk size in run/reshape method instead of in md

Signed-off-by: raziebe@gmail.com
Signed-off-by: NeilBrown <neilb@suse.de>

have raid10 check chunk size in run method instead of in md

Signed-off-by: raziebe@gmail.com
Signed-off-by: NeilBrown <neilb@suse.de>

have raid0 check chunk size in run method instead of in md.
This is part of a series moving the checks from common code to
the personalities where they belong.

hardsect is short and chunksize is an int, so it is safe to use %.

Signed-off-by: raziebe@gmail.com
Signed-off-by: NeilBrown <neilb@suse.de>

Report to the user what are the raid zones

Signed-off-by: raziebe@gmail.com
Signed-off-by: NeilBrown <neilb@suse.de>

Because of the removal of the device list from
the strips raid0 did not compile with MD_DEBUG flag on
Signed-off-by: NeilBrown <neilb@suse.de>

Replace the linear search with binary search in which_dev.
Signed-off-by: Sandeep K Sinha <sandeepksinha@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>

Remove num_sectors from dev_info and replace start_sector with
end_sector.  This makes a lot of comparisons much simpler.
Signed-off-by: Sandeep K Sinha <sandeepksinha@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>

Get rid of sector_div and hash table for linear raid and replace
with a linear search in which_dev.
The hash table adds a lot of complexity for little if any gain.
Ultimately a binary search will be used which will have smaller
cache foot print, a similar number of memory access, and no
divisions.
Signed-off-by: Sandeep K Sinha <sandeepksinha@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>

Having a macro just to cast a void* isn't really helpful.
I would must rather see that we are simply de-referencing ->private,
than have to know what the macro does.

So open code the macro everywhere and remove the pointless cast.
Signed-off-by: NeilBrown <neilb@suse.de>

This setting doesn't seem to make sense (half the chunk size??) and
shouldn't be needed.
The segment boundary exported by raid0 should simply be the minimum
of the segment boundary of all component devices.  And we already
get that right.
Signed-off-by: NeilBrown <neilb@suse.de>

If we treat conf->devlist more like a 2 dimensional array,
we can get the devlist for a particular zone simply by indexing
that array, so we don't need to store the pointers to subarrays
in strip_zone.  This makes strip_zone smaller and so (hopefully)
searches faster.
Signed-of-by: NeilBrown <neilb@suse.de>

storing ->sectors is redundant as is can be computed from the
difference  z->zone_end - (z-1)->zone_end

The one place where it is used, it is just as efficient to use
a zone_end value instead.

And removing it makes strip_zone smaller, so they array of these that
is searched on every request has a better chance to say in cache.

So discard the field and get the value from elsewhere.
Signed-off-by: NeilBrown <neilb@suse.de>

raid0_stop() removes all references to the raid0 configuration but
misses to free the ->devlist buffer.

This patch closes this leak, removes a pointless initialization and
fixes a coding style issue in raid0_stop().
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>

Currently the raid0 configuration is allocated in raid0_run() while
the buffers for the strip_zone and the dev_list arrays are allocated
in create_strip_zones(). On errors, all three buffers are freed
in raid0_run().

It's easier and more readable to do the allocation and cleanup within
a single function. So move that code into create_strip_zones().
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>

Currently raid0_run() always returns -ENOMEM on errors. This is
incorrect as running the array might fail for other reasons, for
example because not all component devices were available.

This patch changes create_strip_zones() so that it returns a proper
error code (either -ENOMEM or -EINVAL) rather than 1 on errors and
makes raid0_run(), its single caller, return that value instead
of -ENOMEM.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>

The "sector_shift" and "spacing" fields of struct raid0_private_data
were only used for the hash table lookups. So the removal of the
hash table allows get rid of these fields as well which simplifies
create_strip_zones() and raid0_run() quite a bit.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>

The raid0 hash table has become unused due to the changes in the
previous patch. This patch removes the hash table allocation and
setup code and kills the hash_table field of struct raid0_private_data.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>

1/ remove current_start.  The same value is available in
     zone->dev_start and storing it separately doesn't gain anything.
2/ rename curr_zone_start to curr_zone_end as we are now more
     focused on the 'end' of each zone.  We end up storing the
     same number though - the old name was a little confusing
     (and what does 'current' mean in this context anyway).
Signed-off-by: NeilBrown <neilb@suse.de>

The number of strip_zones of a raid0 array is bounded by the number of
drives in the array and is in fact much smaller for typical setups. For
example, any raid0 array containing identical disks will have only
a single strip_zone.

Therefore, the hash tables which are used for quickly finding the
strip_zone that holds a particular sector are of questionable value
and add quite a bit of unnecessary complexity.

This patch replaces the hash table lookup by equivalent code which
simply loops over all strip zones to find the zone that holds the
given sector.

In order to make this loop as fast as possible, the zone->start field
of struct strip_zone has been renamed to zone_end, and it now stores
the beginning of the next zone in sectors. This allows to save one
addition in the loop.

Subsequent cleanup patches will remove the hash table structure.
Signed-off-by: Andre Noll <maan@systemlinux.org>
Signed-off-by: NeilBrown <neilb@suse.de>

* 'master' of git://git.kernel.org/pub/scm/linux/kernel/git/sam/kbuild-next: (53 commits)
  .gitignore: ignore *.lzma files
  kbuild: add generic --set-str option to scripts/config
  kbuild: simplify argument loop in scripts/config
  kbuild: handle non-existing options in scripts/config
  kallsyms: generalize text region handling
  kallsyms: support kernel symbols in Blackfin on-chip memory
  documentation: make version fix
  kbuild: fix a compile warning
  gitignore: Add GNU GLOBAL files to top .gitignore
  kbuild: fix delay in setlocalversion on readonly source
  README: fix misleading pointer to the defconf directory
  vmlinux.lds.h update
  kernel-doc: cleanup perl script
  Improve vmlinux.lds.h support for arch specific linker scripts
  kbuild: fix headers_exports with boolean expression
  kbuild/headers_check: refine extern check
  kbuild: fix "Argument list too long" error for "make headers_check",
  ignore *.patch files
  Remove bashisms from scripts
  menu: fix embedded menu presentation
  ...

Signed-off-by: Sam Ravnborg <sam@ravnborg.org>

* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/roland/infiniband:
  mlx4_core: Don't double-free IRQs when falling back from MSI-X to INTx
  IB/mthca: Don't double-free IRQs when falling back from MSI-X to INTx
  IB/mlx4: Add strong ordering to local inval and fast reg work requests
  IB/ehca: Remove superfluous bitmasks from QP control block
  RDMA/cxgb3: Limit fast register size based on T3 limitations
  RDMA/cxgb3: Report correct port state and MTU
  mlx4_core: Add module parameter for number of MTTs per segment
  IB/mthca: Add module parameter for number of MTTs per segment
  RDMA/nes: Fix off-by-one bugs in reset_adapter_ne020() and init_serdes()
  infiniband: Remove void casts
  IB/ehca: Increment version number
  IB/ehca: Remove unnecessary memory operations for userspace queue pairs
  IB/ehca: Fall back to vmalloc() for big allocations
  IB/ehca: Replace vmalloc() with kmalloc() for queue allocation

* git://git.kernel.org/pub/scm/linux/kernel/git/jaswinder/headers-check-2.6:
  headers_check fix: mn10300, setup.h
  headers_check fix: mn10300, ptrace.h

Fix recent fusion driver kernel-doc fatal error and warnings.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Cc: Eric.Moore@lsi.com
Cc: support@lsi.com
Cc: DL-MPTFusionLinux@lsi.com
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

In addition to KT_DEAD which has limited support for diacriticals,
there is KT_DEAD2 that can support 256 criticals, so let's advertise
it in <linux/keyboard.h>.

This lets userland know abut the drivers/char/keyboard.c function
k_dead2, which supports more than the few trivial ones that k_dead
supports.
Signed-off-by: Samuel Thibault <samuel.thibault@ens-lyon.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>

Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>

Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>

If an option does not exist in .config, set it at the end of the file.
Signed-off-by: Michal Marek <mmarek@suse.cz>
Signed-off-by: Sam Ravnborg <sam@ravnborg.org>