Add DT data for OMAP3 Beagle board. The board has the following displays:

dvi: uses TFP410 encoder to convert DPI to DVI
tv: analog svideo
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

Add DT data for OMAP4 SDP board. The board has the following displays:

lcd0: a command mode DSI panel connected to OMAP DSI1 encoder
lcd1: a command mode DSI panel connected to OMAP DSI2 encoder
hdmi: OMAP HDMI output with TPD12S015 ESD/level shifter
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

Add DT data for OMAP4 Pandaboard. The board has the following displays:

dvi: uses TFP410 encoder to convert DPI to DVI
hdmi: OMAP HDMI output with TPD12S015 ESD/level shifter
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

Add DT data for OMAP4 display subsystem, which contains the following
blocks:

dss - the wrapper/glue for the display modules
dispc - display controller
dsi - MIPI DSI encoder (two independent modules)
rfbi - MIPI DBI encoder
venc - analog TV encoder
hdmi - HDMI encoder
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

Add DT data for OMAP3 display subsystem, which contains the following
blocks:

dss - the wrapper/glue for the display modules
dispc - display controller
dsi - MIPI DSI encoder
rfbi - MIPI DBI encoder
venc - analog TV encoder
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

Add DT data for OMAP2 display subsystem, which contains the following
blocks:

dss - the wrapper/glue for the display modules
dispc - display controller
rfbi - MIPI DBI encoder
venc - analog TV encoder
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

Set 'ti,set-rate-parent' property for clocks in the dpll4_m4 clock
path, which is used for DSS functional clock. This fixes DSS driver's
clock rate configuration, which needs the rate to be propagated properly
to the divider node (dpll4_m4_ck).
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Christoph Fritz <chf.fritz@googlemail.com>
Tested-by: Marek Belisko <marek@goldelico.com>
Acked-by: Tony Lindgren <tony@atomide.com>

We need to use set-rate-parent for dpll4_m4 clock path, so use the
ti,fixed-factor-clock version which supports set-rate-parent property.

The set-rate-parent flag itself is set in the following patch, this one
just changes the clock driver to ti,fixed-factor-clock without any other
changes.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Christoph Fritz <chf.fritz@googlemail.com>
Tested-by: Marek Belisko <marek@goldelico.com>
Acked-by: Tony Lindgren <tony@atomide.com>

OMAP3630 DPLL4 is different than on OMAP3430, in that it doesn't have
the x2 multiplier for its outputs. This is not currently reflected in
the clock DT data.

Fix the issue by setting the clock multiplier to 1 (instead of 2) for the
DPLL4 output clocks.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Christoph Fritz <chf.fritz@googlemail.com>
Tested-by: Marek Belisko <marek@goldelico.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

The DSS fclk and iclk handles are named differently on OMAP3430 ES1 than
on later OMAP revisions. The ES1 has handles 'dss1_alwon_fck_3430es1'
and 'dss_ick_3430es1', whereas later revisions have similar names but
ending with 'es2'.

This means we don't have one clock handle to which we could refer to
when defining the DSS clocks.

However, as the namespaces are separate for ES1 and ES2+ OMAPs, we can
just rename the handles to 'dss1_alwon_fck' and 'dss_ick' for both ES1
and ES2+, removing the issue.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Tested-by: Christoph Fritz <chf.fritz@googlemail.com>
Tested-by: Marek Belisko <marek@goldelico.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>

Add support for the MMC2/SDIO WiFi Libertas (Marvell) module available
on the CM-T3530 SOM.

Cc: Dmitry Lifshitz <lifshitz@compulab.co.il>
Cc: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Stefan Roese <sr@denx.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Enable DMA controller for USB
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The IOMMU DT nodes have been added for the DSP and IPU
subsystems. The MMUs in OMAP5 are identical to those in
OMAP4, including the bus error back capability on IPU.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add the IOMMU nodes for the DSP and IPU subsystems. The MMU
within the IPU sub-system also supports a bus error back
capability, not available on the DSP MMU.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
[s-anna@ti.com: IPU bus error back addition]
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add the DT node for the IOMMU within the DSP subsystem. The entry
is disabled to keep in line with the hwmod usage as intended by
the deprecated CONFIG_OMAP_IOMMU_IVA2 flag.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
[s-anna@ti.com: split the entry and disable the node]
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Update the IOMMU node for the camera subsystem as per the
OMAP IOMMU bindings.
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
[s-anna@ti.com: corrected interrupt number]
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

OMAP5 has the same iommus as OMAP4, so extend the OMAP4
iommu pdata quirks for OMAP5 as well.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

A new MMU hwmod class and data structures are created
to represent the MMUs within the IPU and DSP processor
subsystems in OMAP5. The MMUs in OMAP5 are identical to
those in OMAP4.

Cc: Benoit Cousson <bcousson@baylibre.com>
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The OMAP iommu driver performs the reset management for the
iommu instances in processor sub-systems using the omap_device
API which are currently supplied as platform data ops. Use pdata
quirks to maintain the functionality as the OMAP iommu driver
gets converted to use DT nodes, until the reset portions are
decoupled from omap_hwmod/omap_device into a separate reset
driver.

This patch adds the pdata quirks for the reset management of
iommus within the DSP (OMAP3 & OMAP4) and IPU subsystems (OMAP4).
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The IOMMU DT adaptation support uses the device name instead
of an iommu object name. Fixup the ISP device archdata MMU
name at runtime if using DT-boot. This allows the OMAP3 camera
to be functional in both legacy and DT boots. The iommu object
names should eventually vanish when all the IOMMU users have
been converted to DT nodes.
Signed-off-by: Suman Anna <s-anna@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The IVA MMU is not functional when used through the hwmod and
omap_device layers. Add fixes to clockdomain and hwmod data
to have it functional. The hwmod changes are needed to enable
the clock, and the SWSUP change is needed to wakeup the domain
because the power domain is programmed to be in RET, and there
is no automatic power domain switching to ON.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

CONFIG_OMAP_IOMMU_IVA2 was defined originally to avoid conflicting
usage by tidspbridge and other iommu users. The same can be achieved
by marking the DT node disabled, so remove this obsolete flag and
the corresponding hwmod data can be enabled.

Cc: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
[s-anna@ti.com: revise commit log]
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

EVM board provides two Ethernet ports, this patch sets them into
dual_emac mode to provide two independent network interfaces.
Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add ABB device nodes for DRA7 family of devices. Data is based on
DRA7 Technical Reference Manual revision I (Sept 2013)
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add ABB device nodes for OMAP443x family of devices. abb_iva is
populated, but disabled as it is not used on current OMAP443x family,
but the node is used on OMAP446x family. Data is based on OMAP443x
Technical Reference Manual revision AN (April 2013).

ABB device nodes for OMAP4460 device Data is based on OMAP4460
Technical Reference Manual revision Z (April 2013)

[nm@ti.com: co-developer]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Andrii.Tseglytskyi <andrii.tseglytskyi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add ABB device node for OMAP36xx family of devices. Data is based on
OMAP36XX Technical Reference Manual revision AB (Dec 2012).

[nm@ti.com: co-developer]
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Andrii.Tseglytskyi <andrii.tseglytskyi@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add card detect gpio for SD card slot and include dt gpio header.
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Add card detect gpio for SD card slot
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

enable sd card slot on am437x-gp-evm
Signed-off-by: Balaji T K <balajitk@ti.com>
Signed-off-by: Mugunthan V N <mugunthanvnm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Added device tree bindings for dwc3, usb2 and usb3 PHYs. The documentation
of these can be found at Documentation/devicetree/bindings/phy/phy-bindings.txt
and Documentation/devicetree/bindings/phy/ti-phy.txt.
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Enable the WiLink6 connected to mmc2.

Signed-off-by: Imre Kaloz <kaloz@openwrt.org
Signed-off-by: Tony Lindgren <tony@atomide.com>

Remove non-compatible id from examples.

CC: Alan Stern <stern@rowland.harvard.edu>
CC: Nishant Menon <nm@ti.com>
CC: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The OMAP EHCI and OHCI controllers are not compatible with drivers
other than "ti,ehci-omap" and "ti,ohci-omap3" respectively, so get
rid of the incompatible ids.

CC: Alan Stern <stern@rowland.harvard.edu>
CC: Nishant Menon <nm@ti.com>
CC: Kevin Hilman <khilman@linaro.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

The necessary clock phandle for the EHCI clock is now provided
via device tree so we no longer need this legacy method.

Update the omap4-panda and omap5-uevm board DTS to provide the
necessary EHCI PHY clock information.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Gumstix DuoVero is an OMAP4430-based Computer On Module.
Parlor is one of the available expansion board.

Tested features:
- GPMC ethernet
- HSUSB2 and OTG
- Audio out
- WiFi and Bluetooth (w2cbw0015 SDIO module)
- LED and button
Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch>
Signed-off-by: Tony Lindgren <tony@atomide.com>

Merge tag 'for_3.15/dts_signed' of git://git.kernel.org/pub/scm/linux/kernel/git/bcousson/linux-omap-dt into omap-for-v3.15/dt

Add craneboard devices
Add more N900 devices
Add am43x-epos-evm and am437x-gp-evm devices
Add OMAP4 DMM devices

Conflicts:
	arch/arm/boot/dts/am43x-epos-evm.dts
	arch/arm/boot/dts/dra7.dtsi

Add Dynamic Memory Manager (DMM) bindings for OMAP4 and OMAP5 and DRA7x devices.
DMM only requires address and irq information.

Add documentation for the DMM bindings.

Originally worked on by Andy Gross <andygro@gmail.com>

Cc: Andy Gross <andygro@gmail.com>
Signed-off-by: Archit Taneja <archit@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

Add gpio keys node for am43x gp evm.
Signed-off-by: Sourav Poddar <sourav.poddar@ti.com>
Signed-off-by: Benoit Cousson <bcousson@baylibre.com>

This patch:
 - enables GPMC h/w and ELM h/w engine for AM43xx devices (am4372.dtsi)
 - adds pinmux and DT node for Micron 4K-paged x8 NAND device (MT29F4G08AB)
   present on following boards:

   am43x-epos-evm:
	On this board, NAND Flash control lines are muxed with QSPI, Thus only
        one of the two can be used at a time. Selection is controlled by:
        (a) dynamically driving following GPIO pin from software
            GPMC_A0(GPIO) == 0 NAND is selected (default)
            GPMC_A0(GPIO) == 1 eMMC is selected
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>

This patch updated MTD/NAND DT node binding to replace deprecated bindings
as per following commit.
    commit ac65caf5
    ARM: OMAP2+: cleaned-up DT support of various ECC schemes
    Also Refer: Documentation/devicetree/bindings/mtd/gpmc-nand.txt
Reviewed-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Pekon Gupta <pekon@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>