- 07 Jan, 2010 24 commits
-
-
hartleys authored
Use the %pM kernel extension to display the MAC address. Signed-off-by:
H Hartley Sweeten <hsweeten@visionengravers.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
hartleys authored
Use the %pM kernel extension to display the MAC address. Signed-off-by:
-
hartleys authored
Use the %pM kernel extension to display the MAC address. Also, remove the 'mac' variable and use nic->mac directly. Signed-off-by:
Peter Jones <pjones@redhat.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by:
-
hartleys authored
Use the %pM kernel extension to display the MAC address. Signed-off-by:
-
hartleys authored
Use the %pM kernel extension to display the MAC address. The only difference in the output is that the MAC address is shown in the usual colon-separated hex notation. Signed-off-by:
-
hartleys authored
Use the %pM kernel extension to display the MAC address. Signed-off-by:
-
Jesper Dangaard Brouer authored
The contents of /proc/net/dev is annoying to parse, because it changes whether there is a space after the "ethX:" or not. It depends upon the size of the "Receive bytes" counter, if the number is below 7 digits, then there is whitespaces else if the number is 8 digits or above there is no space between the ":" and the number. This patch changes the output to assure there is always a space between the ":" and the number. Given that all existing userspace application already need to handle the whitespaces, I see no breakage of existing tools. Signed-off-by:
Jesper Dangaard Brouer <hawk@comx.dk> Acked-by:
Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by:
-
Jesper Dangaard Brouer authored
This is to be used together with switch technologies, like RFC3069, that where the individual ports are not allowed to communicate with each other, but they are allowed to talk to the upstream router. As described in RFC 3069, it is possible to allow these hosts to communicate through the upstream router by proxy_arp'ing. This patch basically allow proxy arp replies back to the same interface (from which the ARP request/solicitation was received). Tunable per device via proc "proxy_arp_pvlan": /proc/sys/net/ipv4/conf/*/proxy_arp_pvlan This switch technology is known by different vendor names: - In RFC 3069 it is called VLAN Aggregation. - Cisco and Allied Telesyn call it Private VLAN. - Hewlett-Packard call it Source-Port filtering or port-isolation. - Ericsson call it MAC-Forced Forwarding (RFC Draft). Signed-off-by:
-
Andy Gospodarek authored
On Wed, Jan 06, 2010 at 10:10:03PM +0100, Eric Dumazet wrote: > Le 06/01/2010 19:38, Eric Dumazet a écrit : > > > > (net-next-2.6 doesnt work well on my bond/vlan setup, I suspect I need a bisection) > > David, I had to revert 1f3c8804 > (bonding: allow arp_ip_targets on separate vlans to use arp validation) > > Or else, my vlan devices dont work (unfortunatly I dont have much time > these days to debug the thing) > > My config : > > +---------+ > vlan.103 -----+ bond0 +--- eth1 (bnx2) > | + > vlan.825 -----+ +--- eth2 (tg3) > +---------+ > > $ cat /proc/net/bonding/bond0 > Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009) > > Bonding Mode: fault-tolerance (active-backup) > Primary Slave: None > Currently Active Slave: eth2 > MII Status: up > MII Polling Interval (ms): 100 > Up Delay (ms): 0 > Down Delay (ms): 0 > > Slave Interface: eth1 (bnx2) > MII Status: down > Link Failure Count: 1 > Permanent HW addr: 00:1e:0b:ec:d3:d2 > > Slave Interface: eth2 (tg3) > MII Status: up > Link Failure Count: 0 > Permanent HW addr: 00:1e:0b:92:78:50 > This patch fixes up a problem with found with commit 1f3c8804. The original change overloaded null_or_orig, but doing that prevented any packet handlers that were not tied to a specific device (i.e. ptype->dev == NULL) from ever receiving any frames. The null_or_orig variable cannot be overloaded, and must be kept as NULL to prevent the frame from being ignored by packet handlers designed to accept frames on any interface. Signed-off-by:
Andy Gospodarek <andy@greyhouse.net> Signed-off-by:
Jay Vosburgh <fubar@us.ibm.com> Acked-by:
-
Márton Németh authored
The id_table field of the struct pci_driver is constant in <linux/pci.h> so it is worth to make pci_device_id also constant. The semantic match that finds this kind of pattern is as follows: (http://coccinelle.lip6.fr/) // <smpl> @r@ identifier I1, I2, x; @@ struct I1 { ... const struct I2 *x; ... }; @s@ identifier r.I1, y; identifier r.x, E; @@ struct I1 y = { .x = E, }; @c@ identifier r.I2; identifier s.E; @@ const struct I2 E[] = ... ; @depends on !c@ identifier r.I2; identifier s.E; @@ + const struct I2 E[] = ...; // </smpl> Signed-off-by:
Márton Németh <nm127@freemail.hu> Cc: Julia Lawall <julia@diku.dk> Cc: cocci@diku.dk Signed-off-by:
-
Rémi Denis-Courmont authored
Signed-off-by:
Rémi Denis-Courmont <remi.denis-courmont@nokia.com> Signed-off-by:
-
Rémi Denis-Courmont authored
Send aligned pipe payload if requested to do so. Then, the socket buffer needs not be fragmented anymore. Signed-off-by:
-
Rémi Denis-Courmont authored
Newer Nokia cellular modems can use aligned payload for their GPRS pipe. Signed-off-by:
-
Joe Perches authored
Reduce indentation, make code a little neater. Signed-off-by:
Joe Perches <joe@perches.com> Signed-off-by:
-
Joe Perches authored
Use #include <linux/ not #include <asm/ Add spaces after arguments Comment neatening Make a couple of arrays static const Align function arguments Wrap text at 80 columns where reasonable Cuddle brace else Signed-off-by:
-
Joe Perches authored
Use printk_once Add #define pr_fmt(fmt) KBUILD_MODNAME ": " fmt Convert printks without KERN_<level> to pr_info and pr_cont Signed-off-by:
-
Joe Perches authored
Signed-off-by:
-
Joe Perches authored
Signed-off-by:
-
Giuseppe Cavallaro authored
SMSC Ethernet Transceivers (LAN88710, LAN8710, LAN8720, LAN8187, LAN8700, LAN83C185) provide a mechanism to conserve power when the device is not connected to an active link partner (Energy Detect Mode). So this patch enables the Energy Detect power-down mode for these Transceivers. Signed-off-by:
Giuseppe Cavallaro <peppe.cavallaro@st.com> Signed-off-by:
-
Ron Mercer authored
Signed-off-by:
Ron Mercer <ron.mercer@qlogic.com> Signed-off-by:
-
Ron Mercer authored
New handlers are added here to handle: 1) Small frames (<256 bytes) in a single small buffer. Allocate a new skb and copy the frame. 2) Large frame (>256 bytes) in a page chunk. Allocate an skb, tack it on frags, post to napi_gro_receive(). Signed-off-by:
-
Ron Mercer authored
Using 4-byte aligned headers is problematic for some architectures. Since qlge uses 4-byte aligned rx buffers we split headers for these architectures into a separate buffer and then recopy to align on 2-byte boundary. Signed-off-by:
-
Mike McCormack authored
netif_device_detach() does not take the tx_lock, so it's possible that a call to sky2_xmit_frame is still in progress after netif_device_detach() is complete. Take netif_tx_lock() to make sure all transmits have stopped while we're disabling the devices and that no other CPU is still transmitting a frame after we've disabling the device. Proposed fix for "sky2 panic under load" reported by Berck E. Nash. Signed-off-by:
Mike McCormack <mikem@ring3k.org> Signed-off-by:
-
Mike McCormack authored
Separate code deciding which registers can be accessed out of sky2_get_regs in preparation for adding more conditions into it. Signed-off-by:
Stephen Hemminger <shemminger@vyatta.com> Signed-off-by:
-
- 04 Jan, 2010 6 commits
-
-
Ken Kawasaki authored
axnet_cs: remove unnecessary spin_unlock_irqrestore,spin_lock_irqsave. Signed-off-by:Ken Kawasaki <ken_kawasaki@spring.nifty.jp> Signed-off-by:
-
Amerigo Wang authored
We can rely on kconfig to limit these numbers, no need to limit them at compile time/run time. Users who modify these numbers manually should be responsible for themself. :) Signed-off-by:
WANG Cong <amwang@redhat.com> Cc: Per Liden <per.liden@ericsson.com> Cc: Jon Maloy <jon.maloy@ericsson.com> Cc: Allan Stephens <allan.stephens@windriver.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by:
-
Marc Kleine-Budde authored
This patch adds the flag CAN_CTRLMODE_ONE_SHOT. It is used as mask or flag in the "struct can_ctrlmode". It allows userspace via netlink to set a CAN controller into the special "one-shot" mode. In this mode, if supported by the CAN controller, it tries only once to deliver a CAN frame and aborts it if an error (e.g.: arbitration lost) happens. Signed-off-by:
Marc Kleine-Budde <mkl@pengutronix.de> Acked-by:
Wolfgang Grandegger <wg@grandegger.com> Signed-off-by:
-
Oliver Hartkopp authored
this patch removes the hlist that contains the CAN receiver filter lists. It uses the 'midlayer private' pointer ml_priv and links the filters directly to the CAN netdevice, which allows to omit the walk through the complete CAN devices hlist for each received CAN frame. This patch is tested and does not remove any locking. Signed-off-by:
Oliver Hartkopp <oliver@hartkopp.net> Signed-off-by:
-
Julia Lawall authored
Use kzalloc rather than kcalloc(1,...) The semantic patch that makes this change is as follows: (http://coccinelle.lip6.fr/) // <smpl> @@ @@ - kcalloc(1, + kzalloc( ...) // </smpl> Signed-off-by:
Julia Lawall <julia@diku.dk> Acked-by:
Divy Le Ray <divy@chelsio.com> Signed-off-by:
-
Andy Gospodarek authored
This allows a bond device to specify an arp_ip_target as a host that is not on the same vlan as the base bond device and still use arp validation. A configuration like this, now works: BONDING_OPTS="mode=active-backup arp_interval=1000 arp_ip_target=10.0.100.1 arp_validate=3" 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 16436 qdisc noqueue link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: eth1: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master bond0 qlen 1000 link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff 3: eth0: <BROADCAST,MULTICAST,SLAVE,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast master bond0 qlen 1000 link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff 8: bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff inet6 fe80::213:21ff:febe:33e9/64 scope link valid_lft forever preferred_lft forever 9: bond0.100@bond0: <BROADCAST,MULTICAST,MASTER,UP,LOWER_UP> mtu 1500 qdisc noqueue link/ether 00:13:21:be:33:e9 brd ff:ff:ff:ff:ff:ff inet 10.0.100.2/24 brd 10.0.100.255 scope global bond0.100 inet6 fe80::213:21ff:febe:33e9/64 scope link valid_lft forever preferred_lft forever Ethernet Channel Bonding Driver: v3.6.0 (September 26, 2009) Bonding Mode: fault-tolerance (active-backup) Primary Slave: None Currently Active Slave: eth1 MII Status: up MII Polling Interval (ms): 0 Up Delay (ms): 0 Down Delay (ms): 0 ARP Polling Interval (ms): 1000 ARP IP target/s (n.n.n.n form): 10.0.100.1 Slave Interface: eth1 MII Status: up Link Failure Count: 1 Permanent HW addr: 00:40:05:30:ff:30 Slave Interface: eth0 MII Status: up Link Failure Count: 0 Permanent HW addr: 00:13:21:be:33:e9 Signed-off-by:
-
- 30 Dec, 2009 10 commits
-
-
-
git://git.kernel.org/pub/scm/linux/kernel/git/linville/wireless-2.6John W. Linville authored
Conflicts: drivers/net/wireless/libertas/scan.c
-
H Hartley Sweeten authored
Use the %pM kernel extension to display the MAC address. Signed-off-by:
-
H Hartley Sweeten authored
Use the %pM kernel extension to display the MAC address. Signed-off-by:
-
H Hartley Sweeten authored
Use the %pM kernel extension to display the MAC address. Signed-off-by:
-
H Hartley Sweeten authored
Use the %pM kernel extension to display the MAC address. Signed-off-by:
-
H Hartley Sweeten authored
Use the %pM kernel extension to display the MAC address. Signed-off-by:
-
H Hartley Sweeten authored
Use the %pM kernel extension to display the MAC address. Signed-off-by:
-
H Hartley Sweeten authored
Use the %pM kernel extension to display the MAC address. Signed-off-by:
-
H Hartley Sweeten authored
Use the %pM kernel extension to display the MAC address. Signed-off-by:
-
