- 12 Jan, 2012 34 commits
-
-
Alan Stern authored
commit c6187597 upstream. Problems with NVIDIA's OHCI host controllers persist. After looking carefully through the spec, I finally realized that when a controller is reset it then automatically goes into a SUSPEND state in which it is completely quiescent (no DMA and no IRQs) and from which it will not awaken until the system puts it into the OPERATIONAL state. Therefore there's no need to worry about controllers being in the RESET state for extended periods, or remaining in the OPERATIONAL state during system shutdown. The proper action for device initialization is to put the controller into the RESET state (if it's not there already) and then to issue a software reset. Similarly, the proper action for device shutdown is simply to do a software reset. This patch (as1499) implements such an approach. It simplifies initialization and shutdown, and allows the NVIDIA shutdown-quirk code to be removed. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> Tested-by: Andre "Osku" Schmidt <andre.osku.schmidt@googlemail.com> Tested-by: Arno Augustin <Arno.Augustin@web.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Felipe Balbi authored
commit 18b7ede5 upstream. [ removed the dwc3 portion of the patch as it didn't apply to older kernels - gregkh] According to USB 3.0 Specification Table 9-22, if bmAttributes [4:0] are set to zero, it means "no streams supported", but the way this helper was defined on Linux, we will *always* have one stream which might cause several problems. For example on DWC3, we would tell the controller endpoint has streams enabled and yet start transfers with Stream ID set to 0, which would goof up the host side. While doing that, convert the macro to an inline function due to the different checks we now need. Signed-off-by: Felipe Balbi <balbi@ti.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Janne Snabb authored
commit 3c8c9316 upstream. Add support for Chinese Noname HSPA USB modem which is apparently manufactured by a company called ZD Incorporated (based on texts in the Windows drivers). This product is available at least from Dealextreme (SKU 80032) and possibly in India with name Olive V-MW250. It is based on Qualcomm MSM6280 chip. I needed to also add "options usb-storage quirks=0685:7000:i" in modprobe configuration because udevd or the kernel keeps poking the embedded fake-cd-rom which fails and causes the device to reset. There might be a better way to accomplish the same. usb_modeswitch is not needed with this device. Signed-off-by: Janne Snabb <snabb@epipe.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
VU Tuan Duc authored
commit 5b061623 upstream. Add VendorID/ProductID for USB 3G dongle Model VT1000 of Viettel. Signed-off-by: VU Tuan Duc <ducvt@viettel.com.vn> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Hans de Goede authored
commit 71d85724 upstream. I encountered a result of COMP_2ND_BW_ERR while improving how the pwc webcam driver handles not having the full usb1 bandwidth available to itself. I created the following test setup, a NEC xhci controller with a single TT USB 2 hub plugged into it, with a usb keyboard and a pwc webcam plugged into the usb2 hub. This caused the following to show up in dmesg when trying to stream from the pwc camera at its highest alt setting: xhci_hcd 0000:01:00.0: ERROR: unexpected command completion code 0x23. usb 6-2.1: Not enough bandwidth for altsetting 9 And usb_set_interface returned -EINVAL, which caused my pwc code to not do the right thing as it expected -ENOSPC. This patch makes the xhci driver properly handle COMP_2ND_BW_ERR and makes usb_set_interface return -ENOSPC as expected. This should be backported to stable kernels as old as 2.6.32. Signed-off-by: Hans de Goede <hdegoede@redhat.com> Signed-off-by: Sarah Sharp <sarah.a.sharp@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Clemens Ladisch authored
commit bc677d5b upstream. Add a new field num_mapped_sgs to struct urb so that we have a place to store the number of mapped entries and can also retain the original value of entries in num_sgs. Previously, usb_hcd_map_urb_for_dma() would overwrite this with the number of mapped entries, which would break dma_unmap_sg() because it requires the original number of entries. This fixes warnings like the following when using USB storage devices: ------------[ cut here ]------------ WARNING: at lib/dma-debug.c:902 check_unmap+0x4e4/0x695() ehci_hcd 0000:00:12.2: DMA-API: device driver frees DMA sg list with different entry count [map count=4] [unmap count=1] Modules linked in: ohci_hcd ehci_hcd Pid: 0, comm: kworker/0:1 Not tainted 3.2.0-rc2+ #319 Call Trace: <IRQ> [<ffffffff81036d3b>] warn_slowpath_common+0x80/0x98 [<ffffffff81036de7>] warn_slowpath_fmt+0x41/0x43 [<ffffffff811fa5ae>] check_unmap+0x4e4/0x695 [<ffffffff8105e92c>] ? trace_hardirqs_off+0xd/0xf [<ffffffff8147208b>] ? _raw_spin_unlock_irqrestore+0x33/0x50 [<ffffffff811fa84a>] debug_dma_unmap_sg+0xeb/0x117 [<ffffffff8137b02f>] usb_hcd_unmap_urb_for_dma+0x71/0x188 [<ffffffff8137b166>] unmap_urb_for_dma+0x20/0x22 [<ffffffff8137b1c5>] usb_hcd_giveback_urb+0x5d/0xc0 [<ffffffffa0000d02>] ehci_urb_done+0xf7/0x10c [ehci_hcd] [<ffffffffa0001140>] qh_completions+0x429/0x4bd [ehci_hcd] [<ffffffffa000340a>] ehci_work+0x95/0x9c0 [ehci_hcd] ... ---[ end trace f29ac88a5a48c580 ]--- Mapped at: [<ffffffff811faac4>] debug_dma_map_sg+0x45/0x139 [<ffffffff8137bc0b>] usb_hcd_map_urb_for_dma+0x22e/0x478 [<ffffffff8137c494>] usb_hcd_submit_urb+0x63f/0x6fa [<ffffffff8137d01c>] usb_submit_urb+0x2c7/0x2de [<ffffffff8137dcd4>] usb_sg_wait+0x55/0x161 Signed-off-by: Clemens Ladisch <clemens@ladisch.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Malte Schröder authored
commit 08e87d0d upstream. Hi, below patch adds the USB-ID of the serial adapters sold by Multiplex RC (www.multiplex-rc.de). Signed-off-by: Malte Schröder <maltesch@gmx.de> Cc: stable <stable@vger.kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Johan Hovold authored
commit 694c6301 upstream. Fix regression introduced by commit 507ca9bc ([PATCH] USB: add ability for usb-serial drivers to determine if their write urb is currently being used.) which inverted the logic in write_room so that it returns zero when the write urb is actually free. Signed-off-by: Johan Hovold <jhovold@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Felipe Contreras authored
commit 772aed45 upstream. In musb_init_controller() there's a pm_runtime_put(), but there's no pm_runtime_get(), which creates a mismatch that causes the driver to sleep when it shouldn't. This was introduced in 7acc6197[1], but it wasn't triggered in my setup until 18a26892[2] was merged to Linus' branch at point df0914[3]. IOW; when PM is working as it was supposed to. However, it seems most of the time this is used in a way that keeps the counter above 0, so nobody noticed. Also, it seems to depend on the configuration used in versions before 3.1, but not later (or in it). I found the problem by loading isp1704_charger before any usb gadgets: http://article.gmane.org/gmane.linux.kernel/1226122 All versions after 2.6.39 are affected. [1] usb: musb: Idle path retention and offmode support for OMAP3 [2] OMAP2+: musb: hwmod adaptation for musb registration [3] Merge branch 'omap-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 Cc: Hema HK <hemahk@ti.com> Signed-off-by: Felipe Contreras <felipe.contreras@gmail.com> Signed-off-by: Felipe Balbi <balbi@ti.com>
-
Oliver Neukum authored
commit 35284b3d upstream. The Guillemot Webcam Hercules Dualpix Exchange camera has been reported with a second ID. Signed-off-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Huajun Li authored
usb: usb-storage doesn't support dynamic id currently, the patch disables the feature to fix an oops commit 1a3a026b upstream. Echo vendor and product number of a non usb-storage device to usb-storage driver's new_id, then plug in the device to host and you will find following oops msg, the root cause is usb_stor_probe1() refers invalid id entry if giving a dynamic id, so just disable the feature. [ 3105.018012] general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC [ 3105.018062] CPU 0 [ 3105.018075] Modules linked in: usb_storage usb_libusual bluetooth dm_crypt binfmt_misc snd_hda_codec_analog snd_hda_intel snd_hda_codec snd_hwdep hp_wmi ppdev sparse_keymap snd_pcm snd_seq_midi snd_rawmidi snd_seq_midi_event snd_seq snd_timer snd_seq_device psmouse snd serio_raw tpm_infineon soundcore i915 snd_page_alloc tpm_tis parport_pc tpm tpm_bios drm_kms_helper drm i2c_algo_bit video lp parport usbhid hid sg sr_mod sd_mod ehci_hcd uhci_hcd usbcore e1000e usb_common floppy [ 3105.018408] [ 3105.018419] Pid: 189, comm: khubd Tainted: G I 3.2.0-rc7+ #29 Hewlett-Packard HP Compaq dc7800p Convertible Minitower/0AACh [ 3105.018481] RIP: 0010:[<ffffffffa045830d>] [<ffffffffa045830d>] usb_stor_probe1+0x2fd/0xc20 [usb_storage] [ 3105.018536] RSP: 0018:ffff880056a3d830 EFLAGS: 00010286 [ 3105.018562] RAX: ffff880065f4e648 RBX: ffff88006bb28000 RCX: 0000000000000000 [ 3105.018597] RDX: ffff88006f23c7b0 RSI: 0000000000000001 RDI: 0000000000000206 [ 3105.018632] RBP: ffff880056a3d900 R08: 0000000000000000 R09: ffff880067365000 [ 3105.018665] R10: 00000000000002ac R11: 0000000000000010 R12: ffff6000b41a7340 [ 3105.018698] R13: ffff880065f4ef60 R14: ffff88006bb28b88 R15: ffff88006f23d270 [ 3105.018733] FS: 0000000000000000(0000) GS:ffff88007a200000(0000) knlGS:0000000000000000 [ 3105.018773] CS: 0010 DS: 0000 ES: 0000 CR0: 000000008005003b [ 3105.018801] CR2: 00007fc99c8c4650 CR3: 0000000001e05000 CR4: 00000000000006f0 [ 3105.018835] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000 [ 3105.018870] DR3: 0000000000000000 DR6: 00000000ffff0ff0 DR7: 0000000000000400 [ 3105.018906] Process khubd (pid: 189, threadinfo ffff880056a3c000, task ffff88005677a400) [ 3105.018945] Stack: [ 3105.018959] 0000000000000000 0000000000000000 ffff880056a3d8d0 0000000000000002 [ 3105.019011] 0000000000000000 ffff880056a3d918 ffff880000000000 0000000000000002 [ 3105.019058] ffff880056a3d8d0 0000000000000012 ffff880056a3d8d0 0000000000000006 [ 3105.019105] Call Trace: [ 3105.019128] [<ffffffffa0458cd4>] storage_probe+0xa4/0xe0 [usb_storage] [ 3105.019173] [<ffffffffa0097822>] usb_probe_interface+0x172/0x330 [usbcore] [ 3105.019211] [<ffffffff815fda67>] driver_probe_device+0x257/0x3b0 [ 3105.019243] [<ffffffff815fdd43>] __device_attach+0x73/0x90 [ 3105.019272] [<ffffffff815fdcd0>] ? __driver_attach+0x110/0x110 [ 3105.019303] [<ffffffff815fb93c>] bus_for_each_drv+0x9c/0xf0 [ 3105.019334] [<ffffffff815fd6c7>] device_attach+0xf7/0x120 [ 3105.019364] [<ffffffff815fc905>] bus_probe_device+0x45/0x80 [ 3105.019396] [<ffffffff815f98a6>] device_add+0x876/0x990 [ 3105.019434] [<ffffffffa0094e42>] usb_set_configuration+0x822/0x9e0 [usbcore] [ 3105.019479] [<ffffffffa00a3492>] generic_probe+0x62/0xf0 [usbcore] [ 3105.019518] [<ffffffffa0097a46>] usb_probe_device+0x66/0xb0 [usbcore] [ 3105.019555] [<ffffffff815fda67>] driver_probe_device+0x257/0x3b0 [ 3105.019589] [<ffffffff815fdd43>] __device_attach+0x73/0x90 [ 3105.019617] [<ffffffff815fdcd0>] ? __driver_attach+0x110/0x110 [ 3105.019648] [<ffffffff815fb93c>] bus_for_each_drv+0x9c/0xf0 [ 3105.019680] [<ffffffff815fd6c7>] device_attach+0xf7/0x120 [ 3105.019709] [<ffffffff815fc905>] bus_probe_device+0x45/0x80 [ 3105.021040] usb usb6: usb auto-resume [ 3105.021045] usb usb6: wakeup_rh [ 3105.024849] [<ffffffff815f98a6>] device_add+0x876/0x990 [ 3105.025086] [<ffffffffa0088987>] usb_new_device+0x1e7/0x2b0 [usbcore] [ 3105.025086] [<ffffffffa008a4d7>] hub_thread+0xb27/0x1ec0 [usbcore] [ 3105.025086] [<ffffffff810d5200>] ? wake_up_bit+0x50/0x50 [ 3105.025086] [<ffffffffa00899b0>] ? usb_remote_wakeup+0xa0/0xa0 [usbcore] [ 3105.025086] [<ffffffff810d49b8>] kthread+0xd8/0xf0 [ 3105.025086] [<ffffffff81939884>] kernel_thread_helper+0x4/0x10 [ 3105.025086] [<ffffffff8192a8c0>] ? _raw_spin_unlock_irq+0x50/0x80 [ 3105.025086] [<ffffffff8192b1b4>] ? retint_restore_args+0x13/0x13 [ 3105.025086] [<ffffffff810d48e0>] ? __init_kthread_worker+0x80/0x80 [ 3105.025086] [<ffffffff81939880>] ? gs_change+0x13/0x13 [ 3105.025086] Code: 00 48 83 05 cd ad 00 00 01 48 83 05 cd ad 00 00 01 4c 8b ab 30 0c 00 00 48 8b 50 08 48 83 c0 30 48 89 45 a0 4c 89 a3 40 0c 00 00 <41> 0f b6 44 24 10 48 89 55 a8 3c ff 0f 84 b8 04 00 00 48 83 05 [ 3105.025086] RIP [<ffffffffa045830d>] usb_stor_probe1+0x2fd/0xc20 [usb_storage] [ 3105.025086] RSP <ffff880056a3d830> [ 3105.060037] hub 6-0:1.0: hub_resume [ 3105.062616] usb usb5: usb auto-resume [ 3105.064317] ehci_hcd 0000:00:1d.7: resume root hub [ 3105.094809] ---[ end trace a7919e7f17c0a727 ]--- [ 3105.130069] hub 5-0:1.0: hub_resume [ 3105.132131] usb usb4: usb auto-resume [ 3105.132136] usb usb4: wakeup_rh [ 3105.180059] hub 4-0:1.0: hub_resume [ 3106.290052] usb usb6: suspend_rh (auto-stop) [ 3106.290077] usb usb4: suspend_rh (auto-stop) Signed-off-by: Huajun Li <huajun.li.lee@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Greg Kroah-Hartman authored
commit 59bf5cf9 upstream. We were sending data on the stack when uploading firmware, which causes some machines fits, and is not allowed. Fix this by using the buffer we already had around for this very purpose. Reported-by: Wouter M. Koolen <wmkoolen@cwi.nl> Tested-by: Wouter M. Koolen <wmkoolen@cwi.nl> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Julia Lawall authored
commit e7c8e860 upstream. On some failures, the country_code field of an acm structure is freed without freeing the acm structure itself. Elsewhere, operations including memcpy and kfree are performed on the country_code field. The patch sets the country_code field to NULL when it is freed, and likewise sets the country_code_size field to 0. Signed-off-by: Julia Lawall <julia@diku.dk> Acked-by: Oliver Neukum <oneukum@suse.de> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Jan Kara authored
commit d2eb8c35 upstream. During BKL removal in 2.6.38, conversion of files from in-ICB format to normal format got broken. We call ->writepage with i_data_sem held but udf_get_block() also acquires i_data_sem thus creating A-A deadlock. We fix the problem by dropping i_data_sem before calling ->writepage() which is safe since i_mutex still protects us against any changes in the file. Also fix pagelock - i_data_sem lock inversion in udf_expand_file_adinicb() by dropping i_data_sem before calling find_or_create_page(). Reported-by: Matthias Matiak <netzpython@mail-on.us> Tested-by: Matthias Matiak <netzpython@mail-on.us> Reviewed-by: Namjae Jeon <linkinjeon@gmail.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Li Zefan authored
commit 0d19ea86 upstream. If we mount a hierarchy with a specified name, the name is unique, and we can use it to mount the hierarchy without specifying its set of subsystem names. This feature is documented is Documentation/cgroups/cgroups.txt section 2.3 Here's an example: # mount -t cgroup -o cpuset,name=myhier xxx /cgroup1 # mount -t cgroup -o name=myhier xxx /cgroup2 But it was broken by commit 32a8cf23 (cgroup: make the mount options parsing more accurate) This fixes the regression. Signed-off-by: Li Zefan <lizf@cn.fujitsu.com> Signed-off-by: Tejun Heo <tj@kernel.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Claudio Scordino authored
commit dbf1115d upstream. Patch to fix a spinlock lockup in the driver that sometimes happens when the tasklet starts. Signed-off-by: Claudio Scordino <claudio@evidence.eu.com> Signed-off-by: Dave Bender <codehero@gmail.com> Tested-by: Dave Bender <codehero@gmail.com> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com> Acked-by: Alan Cox <alan@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Alan Stern authored
commit d8cae98c upstream. The documentation for usbmon is out of date; the usbfs "devices" file now exists in /sys/kernel/debug/usb rather than /proc/bus/usb. This patch (as1505) updates the documentation accordingly, and also mentions that the necessary information can be found by running lsusb. Signed-off-by: Alan Stern <stern@rowland.harvard.edu> CC: Pete Zaitcev <zaitcev@redhat.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Jan Kara authored
commit 33c104d4 upstream. WARN_ON_ONCE(IS_RDONLY(inode)) tends to trip when filesystem hits error and is remounted read-only. This unnecessarily scares users (well, they should be scared because of filesystem error, but the stack trace distracts them from the right source of their fear ;-). We could as well just remove the WARN_ON but it's not hard to fix it to not trip on filesystem with errors and not use more cycles in the common case so that's what we do. Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Jeff Mahoney authored
commit a9e36da6 upstream. This patch fixes a crash in reiserfs_delete_xattrs during umount. When shrink_dcache_for_umount clears the dcache from generic_shutdown_super, delayed evictions are forced to disk. If an evicted inode has extended attributes associated with it, it will need to walk the xattr tree to locate and remove them. But since shrink_dcache_for_umount will BUG if it encounters active dentries, the xattr tree must be released before it's called or it will crash during every umount. This patch forces the evictions to occur before generic_shutdown_super by calling shrink_dcache_sb first. The additional evictions caused by the removal of each associated xattr file and dir will be automatically handled as they're added to the LRU list. CC: reiserfs-devel@vger.kernel.org Signed-off-by: Jeff Mahoney <jeffm@suse.com> Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Jan Kara authored
commit a06d789b upstream. When jqfmt mount option is not specified on remount, we mistakenly clear s_jquota_fmt value stored in superblock. Fix the problem. CC: reiserfs-devel@vger.kernel.org Signed-off-by: Jan Kara <jack@suse.cz> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Steven Rostedt authored
commit 49908a1b upstream. A update is made to the sched:sched_switch event that adds some logic to the first parameter of the __print_flags() that shows the state of tasks. This change cause perf to fail parsing the flags. A simple fix is needed to have the parser be able to process ops within the argument. Reported-by: Andrew Vagin <avagin@openvz.org> Signed-off-by: Steven Rostedt <rostedt@goodmis.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Ram Vepa authored
commit eddfb675 upstream. Prevent a receive data corruption by ensuring that the write to update the rcvhdrheadn register to generate an interrupt is at the very end of the receive processing. Signed-off-by: Ramkrishna Vepa <ram.vepa@qlogic.com> Signed-off-by: Mike Marciniszyn <mike.marciniszyn@qlogic.com> Signed-off-by: Roland Dreier <roland@purestorage.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Aurelien Jacobs authored
commit e8303a3b upstream. Adds the device id needed for the USB Ethernet Adapter delivered by ASUS with their Zenbook. Signed-off-by: Aurelien Jacobs <aurel@gnuage.org> Acked-by: Grant Grundler <grundler@chromium.org> Signed-off-by: David S. Miller <davem@davemloft.net> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Li Zhong authored
commit e4f387d8 upstream. Unpaired calling of probe_hcall_entry and probe_hcall_exit might happen as following, which could cause incorrect preempt count. __trace_hcall_entry => trace_hcall_entry -> probe_hcall_entry => get_cpu_var => preempt_disable __trace_hcall_exit => trace_hcall_exit -> probe_hcall_exit => put_cpu_var => preempt_enable where: A => B and A -> B means A calls B, but => means A will call B through function name, and B will definitely be called. -> means A will call B through function pointer, so B might not be called if the function pointer is not set. So error happens when only one of probe_hcall_entry and probe_hcall_exit get called during a hcall. This patch tries to move the preempt count operations from probe_hcall_entry and probe_hcall_exit to its callers. Reported-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Li Zhong <zhong@linux.vnet.ibm.com> Tested-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Anton Blanchard authored
commit 37fb9a02 upstream. When re-enabling interrupts we have code to handle edge sensitive decrementers by resetting the decrementer to 1 whenever it is negative. If interrupts were disabled long enough that the decrementer wrapped to positive we do nothing. This means interrupts can be delayed for a long time until it finally goes negative again. While we hope interrupts are never be disabled long enough for the decrementer to go positive, we have a very good test team that can drive any kernel into the ground. The softlockup data we get back from these fails could be seconds in the future, completely missing the cause of the lockup. We already keep track of the timebase of the next event so use that to work out if we should trigger a decrementer exception. Signed-off-by: Anton Blanchard <anton@samba.org> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Pontus Fuchs authored
commit 3f176494 upstream. Commit 80900d01 accidently broke the ABI for testmode commands. Restore the ABI again. Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com> Signed-off-by: Luciano Coelho <coelho@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Pontus Fuchs authored
commit f6efe96e upstream. An nvs with malformed contents could cause the processing of the calibration data to read beyond the end of the buffer. Prevent this from happening by adding bound checking. Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com> Reviewed-by: Luciano Coelho <coelho@ti.com> Signed-off-by: Luciano Coelho <coelho@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Pontus Fuchs authored
commit 2131d3c2 upstream. Check for out of bound FEM index to prevent reading beyond ini memory end. Signed-off-by: Pontus Fuchs <pontus.fuchs@gmail.com> Reviewed-by: Luciano Coelho <coelho@ti.com> Signed-off-by: Luciano Coelho <coelho@ti.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Benjamin Herrenschmidt authored
commit c055fe07 upstream. We used to try to request 8 times more vram than needed, which would fail if the card has a too small BAR (observed with qemu & kvm). Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Benjamin Herrenschmidt authored
commit 1bb0b7d2 upstream. When using a >8bpp framebuffer, offb advertises truecolor, not directcolor, and doesn't touch the color map even if it has a corresponding access method for the real hardware. Thus it needs to set the pseudo-palette with all 3 components of the color, like other truecolor framebuffers, not with copies of the color index like a directcolor framebuffer would do. This went unnoticed for a long time because it's pretty hard to get offb to kick in with anything but 8bpp (old BootX under MacOS will do that and qemu does it). Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Larry Finger authored
commit 3f81f8f1 upstream. Testing on the openSUSE wireless forum has shown that a Linksys WUSB54GC v3 with USB ID 1737:0077 works with rt2800usb when the ID is written to /sys/.../new_id. This ID can therefore be moved out of UNKNOWN. Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net> Acked-by: Gertjan van Wingerde <gwingerde@gmail.com> Acked-by: Ivo van Doorn <IvDoorn@gmail.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Neil Horman authored
commit eea915bb upstream. This oops was reported recently: firmware_loading_store+0xf9/0x17b dev_attr_store+0x20/0x22 sysfs_write_file+0x101/0x134 vfs_write+0xac/0xf3 sys_write+0x4a/0x6e system_call_fastpath+0x16/0x1b The complete backtrace was unfortunately not captured, but details can be found here: https://bugzilla.redhat.com/show_bug.cgi?id=769920 The cause is fairly clear. Its caused by the fact that firmware_loading_store has a case 0 in its switch statement that reads and writes the fw_priv->fw poniter without the protection of the fw_lock mutex. since there is a window between the time that _request_firmware sets fw_priv->fw to NULL and the time the corresponding sysfs file is unregistered, its possible for a user space application to race in, and write a zero to the loading file, causing a NULL dereference in firmware_loading_store. Fix it by extending the protection of the fw_lock mutex to cover all of the firware_loading_store function. Signed-off-by: Neil Horman <nhorman@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Joe Perches authored
commit 2eb7f204 upstream. The Japanese/Korean/Chinese versions still need updating. Also, the stable kernel 2.6.x.y descriptions are out of date and should be updated as well. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Joe Perches authored
commit bc7a2f3a upstream. The old address hasn't worked since the great intrusion of August 2011. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
- 06 Jan, 2012 6 commits
-
-
Greg Kroah-Hartman authored
-
Mohammed Shafi Shajakhan authored
commit b25bfda3 upstream. don't do aggregation related stuff for 'AP mode client power save handling' if aggregation is not enabled in the driver, otherwise it will lead to panic because those data structures won't be never intialized in 'ath_tx_node_init' if aggregation is disabled EIP is at ath_tx_aggr_wakeup+0x37/0x80 [ath9k] EAX: e8c09a20 EBX: f2a304e8 ECX: 00000001 EDX: 00000000 ESI: e8c085e0 EDI: f2a304ac EBP: f40e1ca4 ESP: f40e1c8c DS: 007b ES: 007b FS: 00d8 GS: 00e0 SS: 0068 Process swapper/1 (pid: 0, ti=f40e0000 task=f408e860 task.ti=f40dc000) Stack: 0001e966 e8c09a20 00000000 f2a304ac e8c085e0 f2a304ac f40e1cb0 f8186741 f8186700 f40e1d2c f922988d f2a304ac 00000202 00000001 c0b4ba43 00000000 0000000f e8eb75c0 e8c085e0 205b0001 34383220 f2a304ac f2a30000 00010020 Call Trace: [<f8186741>] ath9k_sta_notify+0x41/0x50 [ath9k] [<f8186700>] ? ath9k_get_survey+0x110/0x110 [ath9k] [<f922988d>] ieee80211_sta_ps_deliver_wakeup+0x9d/0x350 [mac80211] [<c018dc75>] ? __module_address+0x95/0xb0 [<f92465b3>] ap_sta_ps_end+0x63/0xa0 [mac80211] [<f9246746>] ieee80211_rx_h_sta_process+0x156/0x2b0 [mac80211] [<f9247d1e>] ieee80211_rx_handlers+0xce/0x510 [mac80211] [<c018440b>] ? trace_hardirqs_on+0xb/0x10 [<c056936e>] ? skb_queue_tail+0x3e/0x50 [<f9248271>] ieee80211_prepare_and_rx_handle+0x111/0x750 [mac80211] [<f9248bf9>] ieee80211_rx+0x349/0xb20 [mac80211] [<f9248949>] ? ieee80211_rx+0x99/0xb20 [mac80211] [<f818b0b8>] ath_rx_tasklet+0x818/0x1d00 [ath9k] [<f8187a75>] ? ath9k_tasklet+0x35/0x1c0 [ath9k] [<f8187a75>] ? ath9k_tasklet+0x35/0x1c0 [ath9k] [<f8187b33>] ath9k_tasklet+0xf3/0x1c0 [ath9k] [<c0151b7e>] tasklet_action+0xbe/0x180 Cc: Senthil Balasubramanian <senthilb@qca.qualcomm.com> Cc: Rajkumar Manoharan <rmanohar@qca.qualcomm.com> Reported-by: Ashwin Mendonca <ashwinloyal@gmail.com> Tested-by: Ashwin Mendonca <ashwinloyal@gmail.com> Signed-off-by: Mohammed Shafi Shajakhan <mohammed@qca.qualcomm.com> Signed-off-by: John W. Linville <linville@tuxdriver.com> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Oleg Nesterov authored
commit 8a88951b upstream. This is the temporary simple fix for 3.2, we need more changes in this area. 1. do_signal_stop() assumes that the running untraced thread in the stopped thread group is not possible. This was our goal but it is not yet achieved: a stopped-but-resumed tracee can clone the running thread which can initiate another group-stop. Remove WARN_ON_ONCE(!current->ptrace). 2. A new thread always starts with ->jobctl = 0. If it is auto-attached and this group is stopped, __ptrace_unlink() sets JOBCTL_STOP_PENDING but JOBCTL_STOP_SIGMASK part is zero, this triggers WANR_ON(!signr) in do_jobctl_trap() if another debugger attaches. Change __ptrace_unlink() to set the artificial SIGSTOP for report. Alternatively we could change ptrace_init_task() to copy signr from current, but this means we can copy it for no reason and hide the possible similar problems. Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Oleg Nesterov authored
commit 50b8d257 upstream. Test-case: int main(void) { int pid, status; pid = fork(); if (!pid) { for (;;) { if (!fork()) return 0; if (waitpid(-1, &status, 0) < 0) { printf("ERR!! wait: %m\n"); return 0; } } } assert(ptrace(PTRACE_ATTACH, pid, 0,0) == 0); assert(waitpid(-1, NULL, 0) == pid); assert(ptrace(PTRACE_SETOPTIONS, pid, 0, PTRACE_O_TRACEFORK) == 0); do { ptrace(PTRACE_CONT, pid, 0, 0); pid = waitpid(-1, NULL, 0); } while (pid > 0); return 1; } It fails because ->real_parent sees its child in EXIT_DEAD state while the tracer is going to change the state back to EXIT_ZOMBIE in wait_task_zombie(). The offending commit is 823b018e which moved the EXIT_DEAD check, but in fact we should not blame it. The original code was not correct as well because it didn't take ptrace_reparented() into account and because we can't really trust ->ptrace. This patch adds the additional check to close this particular race but it doesn't solve the whole problem. We simply can't rely on ->ptrace in this case, it can be cleared if the tracer is multithreaded by the exiting ->parent. I think we should kill EXIT_DEAD altogether, we should always remove the soon-to-be-reaped child from ->children or at least we should never do the DEAD->ZOMBIE transition. But this is too complex for 3.2. Reported-and-tested-by: Denys Vlasenko <vda.linux@googlemail.com> Tested-by: Lukasz Michalik <lmi@ift.uni.wroc.pl> Acked-by: Tejun Heo <tj@kernel.org> Signed-off-by: Oleg Nesterov <oleg@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Linus Torvalds authored
commit 157e8bf8 upstream. This reverts commit c0afabd3. It causes failures on Toshiba laptops - instead of disabling the alarm, it actually seems to enable it on the affected laptops, resulting in (for example) the laptop powering on automatically five minutes after shutdown. There's a patch for it that appears to work for at least some people, but it's too late to play around with this, so revert for now and try again in the next merge window. See for example http://bugs.debian.org/652869 Reported-and-bisected-by: Andreas Friedrich <afrie@gmx.net> (Toshiba Tecra) Reported-by: Antonio-M. Corbi Bellot <antonio.corbi@ua.es> (Toshiba Portege R500) Reported-by: Marco Santos <marco.santos@waynext.com> (Toshiba Portege Z830) Reported-by: Christophe Vu-Brugier <cvubrugier@yahoo.fr> (Toshiba Portege R830) Cc: Jonathan Nieder <jrnieder@gmail.com> Requested-by: John Stultz <john.stultz@linaro.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-
Mandeep Singh Baines authored
commit f9fab10b upstream. vfork parent uninterruptibly and unkillably waits for its child to exec/exit. This wait is of unbounded length. Ignore such waits in the hung_task detector. Signed-off-by: Mandeep Singh Baines <msb@chromium.org> Reported-by: Sasha Levin <levinsasha928@gmail.com> LKML-Reference: <1325344394.28904.43.camel@lappy> Cc: Linus Torvalds <torvalds@linux-foundation.org> Cc: Ingo Molnar <mingo@elte.hu> Cc: Peter Zijlstra <peterz@infradead.org> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: John Kacur <jkacur@redhat.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
-