The driver failed to export primary boot target if secondary target did not
exist in the FLASH. If boot targets are not valid then driver assumed 0 and
1 as default boot targets. Since these target did not exist in flash, the
driver failed exporting all the targets.

JIRA Key: UPSISCSI-148
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

QLogic applications store the CHAP information in FLASH. During login,
authentication information is provided using an index into the CHAP region.

In order to support QLogic applications along with iscsiadm, updated the
LLD to not add duplicate CHAP entries in the CHAP region and preserve the
existing CHAP info in the CHAP region in FLASH.
This allows QLogic applications to pre-write the CHAP entries in the
CHAP region.

With iscsiadm, when the CHAP authentication information is sent to the LLD, the
LLD searches for the entry in CHAP region in FLASH, if exists then do not add.
If CHAP entry does not exist then add the CHAP entry in the CHAP region.

JIRA Key: UPSISCSI-146
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Driver was not setting the bidirectional CHAP bit correctly in
the DDB entry.

JIRA Key: UPSISCSI-108
Signed-off-by: Lalit Chandivade <lalit.chandivade@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Signed-off-by: Nilesh Javali <nilesh.javali@qlogic.com>
Signed-off-by: Vikas Chaudhary <vikas.chaudhary@qlogic.com>
Reviewed-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

   This patch fixes a situation when  wrb was not being memset to zero
before being used
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

This patch fixes a bug where the task->sc was cleaned up earlier on a
different thread, possibly abort, and the completion comes later.

This was causing a crash which has been reported in multiple places
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

   This patch fixes wrong dmsg setting when we send out wrb.

If the ttt is not ISCSI_RESERVED_TAG then we should be setting
dmsg=1 so that the completion is done without waiting for a
iscsi level response from the target
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

This patch fixes the Kdump failure reported by Redhat wich was caused by
be2iscsi resetting the Chip when be2iscsi detects it is in crashdump mode. If
be2net was loaded before be2iscsi then this leaves be2net driver hanging on to
resources that the chip stopped recognising after the reset.

This patch replaces  chip reset with Function reset so that only the
particular function and not the whole chip is affected
Signed-off-by: Jayamohan Kallickal <jayamohan.kallickal@emulex.com>
Signed-off-by: Mike Christie <michaelc@cs.wisc.edu>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

qlogicpti times out for some tape library operations (like mtx
inventory). It seems SCSI command timeout is hardcoded into the driver.
Fix it by propagating the timeout from scsi request to the controller as
suggested by James Bottomley.

Tested on Sun Ultra 1 with Sun StorEdge L8 Autoloader.
Signed-off-by: Meelis Roos <mroos@linux.ee>
Acked-by: David S. Miller <davem@davemloft.net>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

This patch adds one more check-condition for scsi_dh_alua handler. Without
this, the handler attach fails sometimes during the discovery. I have noticed
this with NetApp E-Series storage with alua mode. Also removed some
unnecessary brackets {} for consistency.
Signed-off-by: Babu Moger <babu.moger@netapp.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

The write buffer command is used to download and burn new IOA FW images.
The same interface can now be used to flash FPGA and flash back DRAM images.
To download and flash the new images takes more than 15 minutes, so increase
the write buffer command timeout to 30 minutes.

The FPGA and flash back DRAM images don't have the same card_type as the IOA FW
image. So, remove the sanity checking from the driver.  The adapter has sanity
checking and will only accept a valid image.
Signed-off-by: Wayne Boyer <wayneb@linux.vnet.ibm.com>
Acked-by: Brian King <brking@linux.vnet.ibm.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

port->dev_list maintains a list of devices attached to a given sas root port.
It needs to be mutated under a lock as contexts outside of the
single-threaded-libsas-workqueue access the list via sas_find_dev_by_rphy().
Fixup locations where the list was being mutated without a lock.

This is a follow-up to commit 5911e963 "[SCSI] libsas: remove expander
from dev list on error", where Luben noted [1]:

    > 2/ We have unlocked list manipulations in sas_ex_discover_end_dev(),
    > sas_unregister_common_dev(), and sas_ex_discover_end_dev()

    Yes, I can see that and that is very unfortunate.

[1]: http://marc.info/?l=linux-scsi&m=131480962006471&w=2Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Add support for get_lesb so that the valid statistics are returned by the
remote peer when RLS command is issued.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Except for obtaining the netdev from lport, fcoe_get_lesb is the common code
for the LLDs.
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Acked-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Link may not be up when the driver receives ulp_start event, and hence
fcoe_ctlr_link_up is not called. Call fcoe_ctlr_link_up during
indicate_netevent only when the interface is enabled. (It has to be called when
enabled because that is an indication that the vlan discovery is completed).
Signed-off-by: Bhanu Prakash Gollapudi <bprakash@broadcom.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Allow the sas-transport-class to update events for local phys via a new
PHY_FUNC_GET_EVENTS command to ->lldd_control_phy().  Fixup drivers that
are not prepared for new enum phy_func values, and unify
->lldd_control_phy() error codes.

These are the SAS defined phy events that are reported in a
smp-report-phy-error-log command:
 * /sys/class/sas_phy/<phyX>/invalid_dword_count
 * /sys/class/sas_phy/<phyX>/running_disparity_error_count
 * /sys/class/sas_phy/<phyX>/loss_of_dword_sync_count
 * /sys/class/sas_phy/<phyX>/phy_reset_problem_count
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Fixes a bug where any phy removed from the port set the port
state to "stopping" - do this only when the last phy removed
from the port.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

DONE_CRC_ERR is not a RNC suspension condition, so do not change the
state to expect the incoming suspension notification.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
[djbw: dropped DONE_CMD_LL_R_ERR change]
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Since libsas has it's own means to escalate SATA/STP device error
handling depending on task status codes, return all SATA/STP I/O
on the normal path.

i.e. skip sas_task_abort() and let sas_ata_task_done() disposition the
qc.  Longer term we want to audit non-essential calls to
sas_task_abort().
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Based on original implementation from Jiangbi Liu and Maciej Trela.

ATAPI transfers happen in two-to-three stages.  The two stage atapi
commands are those that include a dma data transfer.  The data transfer
portion of these operations is handled by the hardware packet-dma
acceleration.  The three-stage commands do not have a data transfer and
are handled without hardware assistance in raw frame mode.

stage1: transmit host-to-device fis to notify the device of an incoming
atapi cdb.  Upon reception of the pio-setup-fis repost the task_context
to perform the dma transfer of the cdb+data (go to stage3), or repost
the task_context to transmit the cdb as a raw frame (go to stage 2).

stage2: wait for hardware notification of the cdb transmission and then
go to stage 3.

stage3: wait for the arrival of the terminating device-to-host fis and
terminate the command.

To keep the implementation simple we only support ATAPI packet-dma
protocol (for commands with data) to avoid needing to handle the data
transfer manually (like we do for SATA-PIO).  This may affect
compatibility for a small number of devices (see
ATA_HORKAGE_ATAPI_MOD16_DMA).

If the data-transfer underruns, or encounters an error the
device-to-host fis is expected to arrive in the unsolicited frame queue
to pass to libata for disposition.  However, in the DONE_UNEXP_FIS (data
underrun) case it appears we need to craft a response.  In the
DONE_REG_ERR case we do receive the UF and propagate it to libsas.
Signed-off-by: Maciej Trela <maciej.trela@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

This will synchronize the version string with internal driver.
Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

set SMP link timeout value to maximum.
Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

with 1 expander, connect 8 HDD, the write performance will be
improved by 80%.
Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

-- change connection behavior
-- set bit8 to 1 for performance tuning
-- set bit0 to 0 to enable retry for no_dest reject case.
Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

disable non data frame retry
Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

spin up issue: some direct attached SAS device can't spin up
Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Add support for Marvell 88SE9480 SAS/SATA HBA
Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Expanders fail to link when the phy rates are mismatched.
Signed-off-by: Xiangliang Yu <yuxiangl@marvell.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Needed to jump to scic_lock unlock.

Also spotted by coccicheck.
Signed-off-by: Jeff Skirvin <jeffrey.d.skirvin@intel.com>
Cc: <stable@kernel.org>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Kill the local smp response buffer.

Besides being unnecessary, it is too small (currently truncates
responses to 60 bytes).  The mid-layer will have already allocated a
sufficiently sized buffer, just kmap and copy into it directly.

Cc: <stable@kernel.org>
Reported-by: Derick Marks <derick.w.marks@intel.com>
Tested-by: Derick Marks <derick.w.marks@intel.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Code Inspection: found two missing break directives. First one will
result in not retrying an a task that report
IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY, the second will result in cosmetic
debug printk conflicting statement stutter. Because checkpatch.pl came
up with a warning regarding unnecessary space before a newline on one of
the fragments associated with the diff context, I took the liberty of
fixing all the cases of this issue in the pair of files touched by this
defect. These cosmetic changes hide the break changes :-(

To help focus, break changes are in pm8001_hwi.c fragment line 1649 for
the IO_OPEN_CNX_ERROR_HW_RESOURCE_BUSY case statement and pm8001_sas.c
line 1000 deals with the conflicting debug print stutter.
Signed-off-by: Mark Salyzyn <mark_salyzyn@us.xyratex.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

On the pm8001, when a device is in the process of going away (device
power off or hot plug), depending on the timing, the driver would return
SAS_PHY_DOWN as the return value to the queuecommand DEV_IS_GONE logic.
The net result is an near infinite retry (especially if SAS debugging is
enabled), the logs will fill with:

kernel: mpi_ssp_completion 2119:e21:SSP IO status 0x13 tag 0xcc1c0000
dlen=90 param=0xe
kernel: wwn=5000c50034069e86  cdb=12 00 00 00 5a 00 00 00 00 00 00 00 00
00 00 00
kernel: sas: lldd_execute_task returned: 138
kernel: sas: lldd_execute_task returned: 138
kernel: sas: lldd_execute_task returned: 138
kernel: sas: lldd_execute_task returned: 138
kernel: sas: lldd_execute_task returned: 138
kernel: sas: lldd_execute_task returned: 138
kernel: sas: lldd_execute_task returned: 138
. . .

This patch changes to leverage the port_attached logic to complete the
command with a status of PHY_DOWN so that the disposition can be handled
immediately and correctly.
Signed-off-by: Mark Salyzyn <mark_salyzyn@us.xyratex.com>
Acked-by: Jack Wang <jack_wang@usish.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Currently fcoe_ddp_min doesn't have default value
so by default not used, so setting up default value
as 4k as this works better by avoiding overhead
of programing DDP for small IOs.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Use real dev in case it has HW vlan acceleration
support since in this case the real dev would
do needed vlan processing, this way unnecessary
vlan layer processing avoided and it gives
slightly better IOPS with 512B size IOs.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

fix holes and better cache aligned fields.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

cache aligned xid and ex_lock beside
removing holes.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>

Re-arrange its fields to avoid padding and have better
cacheline alignments.

Removed not used start_time, end_time and last_pkt_time
fields.

This all reduced this struct size to 448 from 480 and
that also reduced one cacheline on x86_64 beside
eliminating 8 pads. However kept logical fields together.
Signed-off-by: Vasu Dev <vasu.dev@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Yi Zou <yi.zou@intel.com>
Signed-off-by: James Bottomley <JBottomley@Parallels.com>