- 28 Feb, 2024 19 commits
-
-
Douglas Anderson authored
If an eDP panel is not powered on then any attempts to talk to it over the DP AUX channel will timeout. Unfortunately these attempts may be quite slow. Userspace can initiate these attempts either via a /dev/drm_dp_auxN device or via the created i2c device. Making the DP AUX drivers timeout faster is a difficult proposition. In theory we could just poll the panel's HPD line in the AUX transfer function and immediately return an error there. However, this is easier said than done. For one thing, there's no hard requirement to hook the HPD line up for eDP panels and it's OK to just delay a fixed amount. For another thing, the HPD line may not be fast to probe. On parade-ps8640 we need to wait for the bridge chip's firmware to boot before we can get the HPD line and this is a slow process. The fact that the transfers are taking so long to timeout is causing real problems. The open source fwupd daemon sometimes scans DP busses looking for devices whose firmware need updating. If it happens to scan while a panel is turned off this scan can take a long time. The fwupd daemon could try to be smarter and only scan when eDP panels are turned on, but we can also improve the behavior in the kernel. Let's let eDP panels drivers specify that a panel is turned off and then modify the common AUX transfer code not to attempt a transfer in this case. Tested-by:
Steev Klimaszewski <steev@kali.org> Reviewed-by:
Hsin-Yi Wang <hsinyi@chromium.org> Tested-by:
Eizan Miyamoto <eizan@chromium.org> Acked-by:
Neil Armstrong <neil.armstrong@linaro.org> Signed-off-by:
Douglas Anderson <dianders@chromium.org> Link: https://patchwork.freedesktop.org/patch/msgid/20240202141109.1.I24277520ac754ea538c9b14578edc94e1df11b48@changeid
-
Maxime Ripard authored
drmm_connector_init is the preferred function to initialize a drm_connector structure. Let's add a bunch of unit tests for it. Reviewed-by:
Maíra Canal <mcanal@igalia.com> Signed-off-by:
Maxime Ripard <mripard@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20240222-kms-hdmi-connector-state-v7-5-8f4af575fce2@kernel.org
-
Maxime Ripard authored
We're going to need a full-blown, functional, KMS device to test more components of the atomic modesetting infrastructure. Let's add a new helper to create a dumb, mocked, CRTC. By default it will create a CRTC relying only on the default helpers, but drivers are free to deviate from that. Reviewed-by:
-
Maxime Ripard authored
We're going to need a full-blown, functional, KMS device to test more components of the atomic modesetting infrastructure. Let's add a new helper to create a dumb, mocked, primary plane. By default, it will create a linear XRGB8888 plane, using the default helpers. Reviewed-by:
-
Maxime Ripard authored
The mock device we were creating was missing any of the driver-wide helpers. That was fine before since we weren't testing the atomic state path, but we're going to start, so let's use the default implementations. Reviewed-by:
-
Maxime Ripard authored
We have a few functions declared in our kunit helpers header, some of them dereferencing the struct drm_driver. However, we don't include the drm_drv.h header file defining that structure, leading to compilation errors if we don't include both headers. Fixes: d9878031 ("drm/tests: helpers: Allow to pass a custom drm_driver") Reviewed-by:
-
Kunwu Chan authored
Use the new KMEM_CACHE() macro instead of direct kmem_cache_create to simplify the creation of SLAB caches. Signed-off-by:
Kunwu Chan <chentao@kylinos.cn> Signed-off-by:
Daniel Vetter <daniel.vetter@ffwll.ch> Link: https://patchwork.freedesktop.org/patch/msgid/20240221085558.166774-1-chentao@kylinos.cn
-
Shradha Gupta authored
In function drm_helper_probe_single_connector_modes() when we enable polling again, if it is already uninitialized, a warning is reported. This patch fixes the warning message by checking if poll is initialized before enabling it. Reported-by:
kernel test robot <oliver.sang@intel.com> Closes: https://lore.kernel.org/oe-lkp/202401191128.db8423f1-oliver.sang@intel.comSigned-off-by:
Shradha Gupta <shradhagupta@linux.microsoft.com> Signed-off-by:
-
Shradha Gupta authored
In drm_kms_helper_poll_disable() check if output polling support is initialized before disabling polling. If not flag this as a warning. Additionally in drm_mode_config_helper_suspend() and drm_mode_config_helper_resume() calls, that re the callers of these functions, avoid invoking them if polling is not initialized. For drivers like hyperv-drm, that do not initialize connector polling, if suspend is called without this check, it leads to suspend failure with following stack [ 770.719392] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done. [ 770.720592] printk: Suspending console(s) (use no_console_suspend to debug) [ 770.948823] ------------[ cut here ]------------ [ 770.948824] WARNING: CPU: 1 PID: 17197 at kernel/workqueue.c:3162 __flush_work.isra.0+0x212/0x230 [ 770.948831] Modules linked in: rfkill nft_counter xt_conntrack xt_owner udf nft_compat crc_itu_t nft_fib_inet nft_fib_ipv4 nft_fib_ipv6 nft_fib nft_reject_inet nf_reject_ipv4 nf_reject_ipv6 nft_reject nft_ct nft_chain_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 ip_set nf_tables nfnetlink vfat fat mlx5_ib ib_uverbs ib_core mlx5_core intel_rapl_msr intel_rapl_common kvm_amd ccp mlxfw kvm psample hyperv_drm tls drm_shmem_helper drm_kms_helper irqbypass pcspkr syscopyarea sysfillrect sysimgblt hv_balloon hv_utils joydev drm fuse xfs libcrc32c pci_hyperv pci_hyperv_intf sr_mod sd_mod cdrom t10_pi sg hv_storvsc scsi_transport_fc hv_netvsc serio_raw hyperv_keyboard hid_hyperv crct10dif_pclmul crc32_pclmul crc32c_intel hv_vmbus ghash_clmulni_intel dm_mirror dm_region_hash dm_log dm_mod [ 770.948863] CPU: 1 PID: 17197 Comm: systemd-sleep Not tainted 5.14.0-362.2.1.el9_3.x86_64 #1 [ 770.948865] Hardware name: Microsoft Corporation Virtual Machine/Virtual Machine, BIOS Hyper-V UEFI Release v4.1 05/09/2022 [ 770.948866] RIP: 0010:__flush_work.isra.0+0x212/0x230 [ 770.948869] Code: 8b 4d 00 4c 8b 45 08 89 ca 48 c1 e9 04 83 e2 08 83 e1 0f 83 ca 02 89 c8 48 0f ba 6d 00 03 e9 25 ff ff ff 0f 0b e9 4e ff ff ff <0f> 0b 45 31 ed e9 44 ff ff ff e8 8f 89 b2 00 66 66 2e 0f 1f 84 00 [ 770.948870] RSP: 0018:ffffaf4ac213fb10 EFLAGS: 00010246 [ 770.948871] RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffffffff8c992857 [ 770.948872] RDX: 0000000000000001 RSI: 0000000000000001 RDI: ffff9aad82b00330 [ 770.948873] RBP: ffff9aad82b00330 R08: 0000000000000000 R09: ffff9aad87ee3d10 [ 770.948874] R10: 0000000000000200 R11: 0000000000000000 R12: ffff9aad82b00330 [ 770.948874] R13: 0000000000000001 R14: 0000000000000000 R15: 0000000000000001 [ 770.948875] FS: 00007ff1b2f6bb40(0000) GS:ffff9aaf37d00000(0000) knlGS:0000000000000000 [ 770.948878] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 [ 770.948878] CR2: 0000555f345cb666 CR3: 00000001462dc005 CR4: 0000000000370ee0 [ 770.948879] Call Trace: [ 770.948880] <TASK> [ 770.948881] ? show_trace_log_lvl+0x1c4/0x2df [ 770.948884] ? show_trace_log_lvl+0x1c4/0x2df [ 770.948886] ? __cancel_work_timer+0x103/0x190 [ 770.948887] ? __flush_work.isra.0+0x212/0x230 [ 770.948889] ? __warn+0x81/0x110 [ 770.948891] ? __flush_work.isra.0+0x212/0x230 [ 770.948892] ? report_bug+0x10a/0x140 [ 770.948895] ? handle_bug+0x3c/0x70 [ 770.948898] ? exc_invalid_op+0x14/0x70 [ 770.948899] ? asm_exc_invalid_op+0x16/0x20 [ 770.948903] ? __flush_work.isra.0+0x212/0x230 [ 770.948905] __cancel_work_timer+0x103/0x190 [ 770.948907] ? _raw_spin_unlock_irqrestore+0xa/0x30 [ 770.948910] drm_kms_helper_poll_disable+0x1e/0x40 [drm_kms_helper] [ 770.948923] drm_mode_config_helper_suspend+0x1c/0x80 [drm_kms_helper] [ 770.948933] ? __pfx_vmbus_suspend+0x10/0x10 [hv_vmbus] [ 770.948942] hyperv_vmbus_suspend+0x17/0x40 [hyperv_drm] [ 770.948944] ? __pfx_vmbus_suspend+0x10/0x10 [hv_vmbus] [ 770.948951] dpm_run_callback+0x4c/0x140 [ 770.948954] __device_suspend_noirq+0x74/0x220 [ 770.948956] dpm_noirq_suspend_devices+0x148/0x2a0 [ 770.948958] dpm_suspend_end+0x54/0xe0 [ 770.948960] create_image+0x14/0x290 [ 770.948963] hibernation_snapshot+0xd6/0x200 [ 770.948964] hibernate.cold+0x8b/0x1fb [ 770.948967] state_store+0xcd/0xd0 [ 770.948969] kernfs_fop_write_iter+0x124/0x1b0 [ 770.948973] new_sync_write+0xff/0x190 [ 770.948976] vfs_write+0x1ef/0x280 [ 770.948978] ksys_write+0x5f/0xe0 [ 770.948979] do_syscall_64+0x5c/0x90 [ 770.948981] ? syscall_exit_work+0x103/0x130 [ 770.948983] ? syscall_exit_to_user_mode+0x12/0x30 [ 770.948985] ? do_syscall_64+0x69/0x90 [ 770.948986] ? do_syscall_64+0x69/0x90 [ 770.948987] ? do_user_addr_fault+0x1d6/0x6a0 [ 770.948989] ? do_syscall_64+0x69/0x90 [ 770.948990] ? exc_page_fault+0x62/0x150 [ 770.948992] entry_SYSCALL_64_after_hwframe+0x72/0xdc [ 770.948995] RIP: 0033:0x7ff1b293eba7 [ 770.949010] Code: 0b 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b7 0f 1f 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 51 c3 48 83 ec 28 48 89 54 24 18 48 89 74 24 [ 770.949011] RSP: 002b:00007ffde3912128 EFLAGS: 00000246 ORIG_RAX: 0000000000000001 [ 770.949012] RAX: ffffffffffffffda RBX: 0000000000000005 RCX: 00007ff1b293eba7 [ 770.949013] RDX: 0000000000000005 RSI: 00007ffde3912210 RDI: 0000000000000004 [ 770.949014] RBP: 00007ffde3912210 R08: 000055d7dd4c9510 R09: 00007ff1b29b14e0 [ 770.949014] R10: 00007ff1b29b13e0 R11: 0000000000000246 R12: 0000000000000005 [ 770.949015] R13: 000055d7dd4c53e0 R14: 0000000000000005 R15: 00007ff1b29f69e0 [ 770.949016] </TASK> [ 770.949017] ---[ end trace e6fa0618bfa2f31d ]--- Built-on: Rhel9, Ubuntu22 Signed-off-by:
-
Thierry Reding authored
The drm_num_crtcs() helper determines the number of CRTCs by iterating over the list of CRTCs that have been registered with the mode config. However, we already keep track of that number in the mode config's num_crtcs field, so we can simply retrieve the value from that and remove the extra helper function. Signed-off-by:
Thierry Reding <treding@nvidia.com> Reviewed-by:
Jani Nikula <jani.nikula@intel.com> Reviewed-by:
Javier Martinez Canillas <javierm@redhat.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240227112038.411846-1-thierry.reding@gmail.com
-
Thomas Zimmermann authored
Include mutex.h, printk.h and types.h, remove several unnecessary include statements, and sort the list alphabetically. Signed-off-by:
Thomas Zimmermann <tzimmermann@suse.de> Reviewed-by:
Helge Deller <deller@gmx.de> Link: https://patchwork.freedesktop.org/patch/msgid/20240219093941.3684-10-tzimmermann@suse.de
-
Thomas Zimmermann authored
Add forward declarations for struct i2c_adapter and struct module, and sort the list alphabetically. Signed-off-by:
-
Thomas Zimmermann authored
Forward declare struct page and remove the include statement. Signed-off-by:
-
Thomas Zimmermann authored
Forward declare struct notifier_block and remove the include statement. Signed-off-by:
-
Thomas Zimmermann authored
Forward declare struct inode and remove the include statement. Signed-off-by:
-
Thomas Zimmermann authored
Forward declare struct backlight_device and remove the include statement. Signed-off-by:
-
Thomas Zimmermann authored
Resolves the proxy include via <linux/fb.h>, which does not require the backlight header. v3: * fix grammar in commit message Signed-off-by:
Greg Kroah-Hartman <gregkh@linuxfoundation.org> Link: https://patchwork.freedesktop.org/patch/msgid/20240219093941.3684-4-tzimmermann@suse.de
-
Thomas Zimmermann authored
Resolves the proxy include via <linux/fb.h>, which does not require the backlight header. v3: * fix grammar in commit message Signed-off-by:
-
Thomas Zimmermann authored
Resolves the proxy include via <linux/fb.h>, which does not require the backlight header. Signed-off-by:
Lee Jones <lee@kernel.org> Link: https://patchwork.freedesktop.org/patch/msgid/20240219093941.3684-2-tzimmermann@suse.de
-
- 26 Feb, 2024 21 commits
-
-
Jocelyn Falempe authored
We found a regression in v5.10 on real-time server, using the rt-kernel and the mgag200 driver. It's some really specialized workload, with <10us latency expectation on isolated core. After the v5.10, the real time tasks missed their <10us latency when something prints on the screen (fbcon or printk) The regression has been bisected to 2 commits: commit 0b34d58b ("drm/mgag200: Enable caching for SHMEM pages") commit 4862ffae ("drm/mgag200: Move vmap out of commit tail") The first one changed the system memory framebuffer from Write-Combine to the default caching. Before the second commit, the mgag200 driver used to unmap the framebuffer after each frame, which implicitly does a cache flush. Both regressions are fixed by this commit, which restore WC mapping for the framebuffer in system memory, and add a cache flush. This is only needed on x86_64, for low-latency workload, so the new kconfig DRM_MGAG200_IOBURST_WORKAROUND depends on PREEMPT_RT and X86. For more context, the whole thread can be found here [1] Signed-off-by:
Jocelyn Falempe <jfalempe@redhat.com> Link: https://lore.kernel.org/dri-devel/20231019135655.313759-1-jfalempe@redhat.com/ # 1 Acked-by:
-
Thomas Zimmermann authored
Backmerging to get drm-misc-next up to v6.8-rc6. Signed-off-by: -
Maxime Ripard authored
The EDID firmware loading mechanism introduced a few built-in EDIDs that could be forced on any connector, bypassing the EDIDs it exposes. While convenient, this limited set of EDIDs doesn't take into account the connector type, and we can end up with an EDID that is completely invalid for a given connector. For example, the edid/800x600.bin file matches the following EDID: edid-decode (hex): 00 ff ff ff ff ff ff 00 31 d8 00 00 00 00 00 00 05 16 01 03 6d 1b 14 78 ea 5e c0 a4 59 4a 98 25 20 50 54 01 00 00 45 40 01 01 01 01 01 01 01 01 01 01 01 01 01 01 a0 0f 20 00 31 58 1c 20 28 80 14 00 15 d0 10 00 00 1e 00 00 00 ff 00 4c 69 6e 75 78 20 23 30 0a 20 20 20 20 00 00 00 fd 00 3b 3d 24 26 05 00 0a 20 20 20 20 20 20 00 00 00 fc 00 4c 69 6e 75 78 20 53 56 47 41 0a 20 20 00 c2 ---------------- Block 0, Base EDID: EDID Structure Version & Revision: 1.3 Vendor & Product Identification: Manufacturer: LNX Model: 0 Made in: week 5 of 2012 Basic Display Parameters & Features: Analog display Signal Level Standard: 0.700 : 0.000 : 0.700 V p-p Blank level equals black level Sync: Separate Composite Serration Maximum image size: 27 cm x 20 cm Gamma: 2.20 DPMS levels: Standby Suspend Off RGB color display First detailed timing is the preferred timing Color Characteristics: Red : 0.6416, 0.3486 Green: 0.2919, 0.5957 Blue : 0.1474, 0.1250 White: 0.3125, 0.3281 Established Timings I & II: DMT 0x09: 800x600 60.316541 Hz 4:3 37.879 kHz 40.000000 MHz Standard Timings: DMT 0x09: 800x600 60.316541 Hz 4:3 37.879 kHz 40.000000 MHz Detailed Timing Descriptors: DTD 1: 800x600 60.316541 Hz 4:3 37.879 kHz 40.000000 MHz (277 mm x 208 mm) Hfront 40 Hsync 128 Hback 88 Hpol P Vfront 1 Vsync 4 Vback 23 Vpol P Display Product Serial Number: 'Linux #0' Display Range Limits: Monitor ranges (GTF): 59-61 Hz V, 36-38 kHz H, max dotclock 50 MHz Display Product Name: 'Linux SVGA' Checksum: 0xc2 So, an analog monitor EDID. However, if the connector was an HDMI monitor for example, it breaks the HDMI specification that requires, among other things, a digital display, the VIC 1 mode and an HDMI Forum Vendor Specific Data Block in an CTA-861 extension. We thus end up with a completely invalid EDID, which thus might confuse HDMI-related code that could parse it. After some discussions on IRC, we identified mainly two ways to fix this: - We can either create more EDIDs for each connector type to provide a built-in EDID that matches the resolution passed in the name, and still be a sensible EDID for that connector type; - Or we can just prevent the EDID to be exposed to userspace if it's built-in. Or possibly both. However, the conclusion was that maybe we just don't need the built-in EDIDs at all and we should just get rid of them. So here we are. Acked-by:Pekka Paalanen <pekka.paalanen@collabora.com> Acked-by:
-
Daniel Vetter authored
Thomas Zimmermann asked to backmerge -rc6 for drm-misc branches, there's a few same-area-changed conflicts (xe and amdgpu mostly) that are getting a bit too annoying. Signed-off-by: -
Daniel Vetter authored
Merge tag 'drm-habanalabs-next-2024-02-26' of https://git.kernel.org/pub/scm/linux/kernel/git/ogabbay/linux into drm-next This tag contains habanalabs driver and accel changes for v6.9. The notable changes are: - New features and improvements: - Configure interrupt affinity according to NUMA nodes for the MSI-X interrupts that are assigned to the userspace application which acquires the device. - Move the HBM MMU page tables to reside inside the HBM to minimize latency when doing page-walks. - Improve the device reset mechanism when consecutive heartbeat failures occur (firmware fails to ack on heartbeat message). - Check also extended errors in the PCIe addr_dec interrupt information. - Rate limit the error messages that can be printed to dmesg log by userspace actions. - Firmware related fixes: - Handle requests from firmware to reserve device memory - Bug fixes and code cleanups: - constify the struct device_type usage in accel (accel_sysfs_device_minor). - Fix the PCI health check by reading uncached register. - Fix reporting of drain events. - Fix debugfs files permissions. - Fix calculation of DRAM BAR base address. Signed-off-by:
-
ssh://gitlab.freedesktop.org/drm/xe/kernelDaniel Vetter authored
drm/xe feature pull for v6.9: UAPI Changes: - New query to the GuC firmware submission version. (José Roberto de Souza) - Remove unused persistent exec_queues (Thomas Hellström) - Add vram frequency sysfs attributes (Sujaritha Sundaresan, Rodrigo Vivi) - Add the flag XE_VM_BIND_FLAG_DUMPABLE to notify devcoredump that mapping should be dumped (Maarten Lankhorst) Cross-drivers Changes: - Make sure intel_wakeref_t is treated as opaque type on i915-display and fix its type on xe Driver Changes: - Drop pre-production workarounds (Matt Roper) - Drop kunit tests for unsuported platforms: PVC and pre-production DG2 (Lucas De Marchi) - Start pumbling SR-IOV support with memory based interrupts for VF (Michal Wajdeczko) - Allow to map BO in GGTT with PAT index corresponding to XE_CACHE_UC to work with memory based interrupts (Michal Wajdeczko) - Improve logging with GT-oriented drm_printers (Michal Wajdeczko) - Add GuC Doorbells Manager as prep work SR-IOV during VF provisioning ((Michal Wajdeczko) - Refactor fake device handling in kunit integration ((Michal Wajdeczko) - Implement additional workarounds for xe2 and MTL (Tejas Upadhyay, Lucas De Marchi, Shekhar Chauhan, Karthik Poosa) - Program a few registers according to perfomance guide spec for Xe2 (Shekhar Chauhan) - Add error handling for non-blocking communication with GuC (Daniele Ceraolo Spurio) - Fix remaining 32b build issues and enable it back (Lucas De Marchi) - Fix build with CONFIG_DEBUG_FS=n (Jani Nikula) - Fix warnings from GuC ABI headers (Matthew Brost) - Introduce Relay Communication for SR-IOV for VF <-> GuC <-> PF (Michal Wajdeczko) - Add mocs reset kunit (Ruthuvikas Ravikumar) - Fix spellings (Colin Ian King) - Disable mid-thread preemption when not properly supported by hardware (Nirmoy Das) - Release mmap mappings on rpm suspend (Badal Nilawar) - Fix BUG_ON on xe_exec by moving fence reservation to the validate stage (Matthew Auld) - Fix xe_exec by reserving extra fence slot for CPU bind (Matthew Brost) - Fix xe_exec with full long running exec queue, now returning -EWOULDBLOCK to userspace (Matthew Brost) - Fix CT irq handler when CT is disabled (Matthew Brost) - Fix VM_BIND_OP_UNMAP_ALL without any bound vmas (Thomas Hellström) - Fix missing __iomem annotations (Thomas Hellström) - Fix exec queue priority handling with GuC (Brian Welty) - Fix setting SLPC flag to GuC when it's not supported (Vinay Belgaumkar) - Fix C6 disabling without SLPC (Matt Roper) - Drop -Wstringop-overflow to fix build with GCC11 (Paul E. McKenney) - Circumvent bogus -Wstringop-overflow in one case (Arnd Bergmann) - Refactor exec_queue user extensions handling and fix USM attributes being applied too late (Brian Welty) - Use circ_buf head/tail convention (Matthew Brost) - Fail build if circ_buf-related defines are modified with incompatible values (Matthew Brost) - Fix several error paths (Dan Carpenter) - Fix CCS copy for small VRAM copy chunks (Thomas Hellström) - Rework driver initialization order and paths to account for driver running in VF mode (Michal Wajdeczko) - Initialize GuC earlier during probe to handle driver in VF mode (Michał Winiarski) - Fix migration use of MI_STORE_DATA_IMM to write PTEs (Matt Roper) - Fix bounds checking in __xe_bo_placement_for_flags (Brian Welty) - Drop display dependency on CONFIG_EXPERT (Jani Nikula) - Do not hand-roll kstrdup when creating snapshot (Michal Wajdeczko) - Stop creating one kunit module per kunit suite (Lucas De Marchi) - Reduce scope and constify variables (Thomas Hellström, Jani Nikula, Michal Wajdeczko) - Improve and document xe_guc_ct_send_recv() (Michal Wajdeczko) - Add proxy communication between CSME and GSC uC (Daniele Ceraolo Spurio) - Fix size calculation when writing pgtable (Fei Yang) - Make sure cfb is page size aligned in stolen memory (Vinod Govindapillai) - Stop printing guc log to dmesg when waiting for GuC fails (Rodrigo Vivi) - Use XE_CACHE_WB instead of XE_CACHE_NONE for cpu coherency on migration (Himal Prasad Ghimiray) - Fix error path in xe_vm_create (Moti Haimovski) - Fix warnings in doc generation (Thomas Hellström, Badal Nilawar) - Improve devcoredump content for mesa debugging (José Roberto de Souza) - Fix crash in trace_dma_fence_init() (José Roberto de Souza) - Improve CT state change handling (Matthew Brost) - Toggle USM support for Xe2 (Lucas De Marchi) - Reduces code duplication to emit PIPE_CONTROL (José Roberto de Souza) - Canonicalize addresses where needed for Xe2 and add to devcoredump (José Roberto de Souza) - Only allow 1 ufence per exec / bind IOCTL (Matthew Brost) - Move all display code to display/ (Jani Nikula) - Fix sparse warnings by correctly using annotations (Thomas Hellström) - Warn on job timeouts instead of using asserts (Matt Roper) - Prefix macros to avoid clashes with sparc (Matthew Brost) - Fix -Walloc-size by subclassing instead of allocating size smaller than struct (Thomas Hellström) - Add status check during gsc header readout (Suraj Kandpal) - Fix infinite loop in vm_bind_ioctl_ops_unwind() (Matthew Brost) - Fix fence refcounting (Matthew Brost) - Fix picking incorrect userptr VMA (Matthew Brost) - Fix USM on integrated by mapping both mem.kernel_bb_pool and usm.bb_pool (Matthew Brost) - Fix double initialization of display power domains (Xiaoming Wang) - Check expected uC versions by major.minor.patch instead of just major.minor (John Harrison) - Bump minimum GuC version to 70.19.2 for all platforms under force-probe (John Harrison) - Add GuC firmware loading for Lunar Lake (John Harrison) - Use kzalloc() instead of hand-rolled alloc + memset (Nirmoy Das) - Fix max page size of VMA during a REMAP (Matthew Brost) - Don't ignore error when pinning pages in kthread (Matthew Auld) - Refactor xe hwmon (Karthik Poosa) - Add debug logs for D3cold (Riana Tauro) - Remove broken TEST_VM_ASYNC_OPS_ERROR (Matthew Brost) - Always allow to override firmware blob with module param and improve log when no firmware is found (Lucas De Marchi) - Fix shift-out-of-bounds due to xe_vm_prepare_vma() accepting zero fences (Thomas Hellström) - Fix shift-out-of-bounds by distinguishing xe_pt/xe_pt_dir subclass (Thomas Hellström) - Fail driver bind if platform supports MSIX, but fails to allocate all of them (Dani Liberman) - Fix intel_fbdev thinking memory is backed by shmem (Matthew Auld) - Prefer drm_dbg() over dev_dbg() (Jani Nikula) - Avoid function cast warnings with clang-16 (Arnd Bergmann) - Enhance xe_bo_move trace (Priyanka Dandamudi) - Fix xe_vma_set_pte_size() not setting the right gpuva.flags for 4K size (Matthew Brost) - Add XE_VMA_PTE_64K VMA flag (Matthew Brost) - Return 2MB page size for compact 64k PTEs (Matthew Brost) - Remove usage of the deprecated ida_simple_xx() API (Christophe JAILLET) - Fix modpost warning on xe_mocs live kunit module (Ashutosh Dixit) - Drop extra newline in from sysfs files (Ashutosh Dixit) - Implement VM snapshot support for BO's and userptr (Maarten Lankhorst) - Add debug logs when skipping rebinds (Matthew Brost) - Fix code generation when mixing build directories (Dafna Hirschfeld) - Prefer struct_size over open coded arithmetic (Erick Archer) Signed-off-by:
-
Maxime Ripard authored
atomic_check and mode_valid do not check for the same things which can lead to surprising result if the userspace commits a mode that didn't go through mode_valid. Let's merge the two implementations into a function called by both. Acked-by:
Sui Jingfeng <sui.jingfeng@linux.dev> Reviewed-by:
Jernej Skrabec <jernej.skrabec@gmail.com> Signed-off-by:
-
Maxime Ripard authored
container_of_const() allows to preserve the pointer constness and is thus more flexible than inline functions. Let's switch all our instances of container_of() to container_of_const(). Reviewed-by:
-
Maxime Ripard authored
We're not doing anything special in atomic_mode_set so we can simply merge it into atomic_enable. Acked-by:
-
Maxime Ripard authored
The sun4i_hdmi driver still uses the non-atomic variants of the encoder hooks, so let's convert to their atomic equivalents. Acked-by:
-
git://anongit.freedesktop.org/drm/drm-miscDaniel Vetter authored
drm-misc-next for v6.9: UAPI Changes: - changes to fdinfo stats Cross-subsystem Changes: agp: - remove unused type field from struct agp_bridge_data Core Changes: ci: - update test names - cleanups gem: - add stats for shared buffers plus updates to amdgpu, i915, xe Documentation: - fixes syncobj: - fixes to waiting and sleeping Driver Changes: bridge: - adv7511: fix crash on irq during probe - dw_hdmi: set bridge type host1x: - cleanups ivpu: - updates to firmware API - refactor BO allocation meson: - fix error handling in probe panel: - revert "drm/panel-edp: Add auo_b116xa3_mode" - add Himax HX83112A plus DT bindings - ltk500hd1829: add support for ltk101b4029w and admatec 9904370 - simple: add BOE BP082WX1-100 8.2" panel plus DT bindungs renesas: - add RZ/G2L DU support plus DT bindings Signed-off-by:
-
Tomi Valkeinen authored
A sync lost issue can be observed with two displays, when moving a plane from one disabled display to an another disabled display, and then enabling the display to which the plane was moved to. The exact requirements for this to trigger are not clear. It looks like the issue is that the layers are left enabled in the first display's OVR registers. Even if the corresponding VP is disabled, it still causes an issue, as if the disabled VP and its OVR would still be in use, leading to the same VID being used by two OVRs. However, this is just speculation based on testing the DSS behavior. Experimentation shows that as a workaround, we can disable all the layers in the OVR when disabling a VP. There should be no downside to this, as the OVR is anyway effectively disabled if its VP is disabled, and it seems to solve the sync lost issue. However, there may be a bigger issue in play here, related to J721e erratum i2097 ("DSS: Disabling a Layer Connected to Overlay May Result in Synclost During the Next Frame"). Experimentation also shows that the OVR's CHANNELIN field has similar issue. So we may need to revisit this when we find out more about the core issue. Fixes: 32a1795f ("drm/tidss: New driver for TI Keystone platform Display SubSystem") Reviewed-by:Aradhya Bhatia <a-bhatia1@ti.com> Signed-off-by:
Tomi Valkeinen <tomi.valkeinen@ideasonboard.com> Link: https://patchwork.freedesktop.org/patch/msgid/20240213-tidss-fixes-v1-2-d709e8dfa505@ideasonboard.com
-
Tomi Valkeinen authored
When the driver sets up the zpos property it sets the default zpos value to the HW id of the plane. That is fine as such, but as on many DSS versions the driver arranges the DRM planes in a different order than the HW planes (to keep the non-scalable planes first), this leads to odd initial zpos values. An example is J721e, where the initial zpos values for DRM planes are 1, 3, 0, 2. In theory the userspace should configure the zpos values properly when using multiple planes, and in that sense the initial zpos values shouldn't matter, but there's really no reason not to fix this and help the userspace apps which don't handle zpos perfectly. In particular, some versions of Weston seem to have issues dealing with the planes with the current default zpos values. So let's change the zpos values for the DRM planes to 0, 1, 2, 3. Another option would be to configure the planes marked as primary planes to zpos 0. On a two display system this would give us plane zpos values of 0, 0, 1, 2. The end result and behavior would be very similar in this option, and I'm not aware that this would actually help us in any way. So, to keep the code simple, I opted for the 0, 1, 2, 3 values. Fixes: 32a1795f ("drm/tidss: New driver for TI Keystone platform Display SubSystem") Reviewed-by:
-
Ricardo B. Marliere authored
Since commit aed65af1 ("drivers: make device_type const"), the driver core can properly handle constant struct device_type. Move the accel_sysfs_device_minor variable to be a constant structure as well, placing it into read-only memory which can not be modified at runtime. Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org> Signed-off-by:
Ricardo B. Marliere <ricardo@marliere.net> Reviewed-by:
Oded Gabbay <ogabbay@kernel.org> Signed-off-by:
-
Ofir Bitton authored
Today we read PCI VENDOR-ID in order to make sure PCI link is healthy. Apparently the VENDOR-ID might be stored on host and hence, when we read it we might not access the PCI bus. In order to make sure PCI health check is reliable, we will start checking the DEVICE-ID instead. Signed-off-by:
Ofir Bitton <obitton@habana.ai> Reviewed-by:
-
Tomer Tayar authored
The reserved memory for FW is currently saved in an ASIC property in units of MB, just like the value that comes from FW. Except the fact that it is not clear from the property's name, it means also that a calculation to actual size is required everywhere that it is used. Modify the property to hold the size in bytes. Signed-off-by:
Tomer Tayar <ttayar@habana.ai> Reviewed-by:
Carl Vanderlip <quic_carlv@quicinc.com> Signed-off-by:
-
Tomer Tayar authored
Currently the reserved memory request from FW is handled when running with preboot only, but this request is relevant also when running with full FW. Modify to always handle this reservation request. Signed-off-by:
-
Ofir Bitton authored
Fetching sensor data can fail due to various reasons. In order not to pollute the kernel log, those error prints must be rate limited. Signed-off-by:
-
Ofir Bitton authored
Due to a H/W issue, AXI drain event does not include a read/write indication, hence we remove this print. Signed-off-by:
-
Dani Liberman authored
The unmasking is for event and it can be other event than RAZWI. Signed-off-by:
Dani Liberman <dliberman@habana.ai> Reviewed-by:
-
Tal Risin authored
Prevent static analysis warning. Signed-off-by:
Tal Risin <trisin@habana.ai> Reviewed-by:
-
