- 22 Oct, 2015 11 commits
-
-
Stephane Viau authored
In order to produce an image, the scalar needs to be fed extra pixels. These top/bottom/left/right values depend on a various of factors, including resolution, scaling type, phase step and initial phase. Pixel Extension are programmed by hardware in most targets - and can be overwritten by software. For some targets (e.g.: msm8996), software *must* program those registers. In order to ease this computation, let's always use bilinear filters, which are easier to program from kernel. Eventually, all of these values will come down from user space for better quality. Signed-off-by:
Stephane Viau <sviau@codeaurora.org> Signed-off-by:
Rob Clark <robdclark@gmail.com>
-
Stephane Viau authored
When calculating phase steps, let's use the same enum mdp_component_type in order to ease the readability; 0/1 indexes are a bit confusing and we now have explicit values to index this type of arrays. Signed-off-by:
-
Stephane Viau authored
The HDMI controller is new in MDP5 v1.7. As of now, this change doesn't reflect the novelty and only adds the basics so the probe gets triggered. Signed-off-by:
-
Stephane Viau authored
The current behavior is to try to get optional clocks and print a dev_err message in case of failure. This looks rather confusing and may increase with the amount of optional clocks. We may need a cleaner way to handle per-device clocks but in the meantime, let's reduce the amount of dev_err messages during the probe. Signed-off-by:
-
Stephane Viau authored
msm_iommu_new() can fail and this change makes sure that we detect the failure and free the allocated domain before going any further. Signed-off-by:
-
Stephane Viau authored
We want to make sure we control all the information being passed down to SMP block. Having access to the cfg pointer here may create bad things in the future. Signed-off-by:
-
Hai Li authored
The current settings for 28nm PHY data lane CFG4 registers do not work with certain panels. This change is to modify them to hw recommended values. Signed-off-by:
Hai Li <hali@codeaurora.org> Signed-off-by:
-
Bjorn Andersson authored
In some configurations the supplies are voltage switches and not LDOs, making the set voltage call to fail. Check with the regulator framework if the supply can change voltage before attempting. Signed-off-by:
Bjorn Andersson <bjorn.andersson@sonymobile.com> Reviewed-by:
Archit Taneja <architt@codeaurora.org> Signed-off-by:
-
Rob Clark authored
Signed-off-by: -
git://linuxtv.org/pinchartl/fbdevDave Airlie authored
rcar-du support for r8a7793/4 * 'drm/next/du' of git://linuxtv.org/pinchartl/fbdev: drm: rcar-du: Add support for the R8A7794 DU drm: rcar-du: Add support for the R8A7793 DU
-
http://github.com/anholt/linuxDave Airlie authored
This pull request introduces the vc4 driver, for kernel modesetting on the Raspberry Pi (bcm2835/bcm2836 architectures). It currently supports a display plane and cursor on the HDMI output. The driver doesn't do 3D, power management, or overlay planes yet. [airlied: fixup the enable/disable vblank APIs] Acked-by:
Daniel Vetter <daniel.vetter@ffwll.ch> * tag 'drm-vc4-next-2015-10-21' of http://github.com/anholt/linux: drm/vc4: Allow vblank to be disabled drm/vc4: Use the fbdev_cma helpers drm/vc4: Add KMS support for Raspberry Pi. drm/vc4: Add devicetree bindings for VC4.
-
- 21 Oct, 2015 6 commits
-
-
Laurent Pinchart authored
The R8A7794 DU has a fixed output routing configuration with one RGB output per CRTC and thus lacks the RGB output routing register field. Signed-off-by:Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
-
Laurent Pinchart authored
The R8A7793 DU is identical to the R8A7791 and thus only requires a new DT compatible string. Signed-off-by: -
Derek Foreman authored
Signed-off-by:
Derek Foreman <derekf@osg.samsung.com> Signed-off-by:
Eric Anholt <eric@anholt.net>
-
Derek Foreman authored
Keep the fbdev_cma pointer around so we can use it on hotplog and close to ensure the frame buffer console is in a useful state. Signed-off-by:
-
Eric Anholt authored
This is enough for fbcon and bringing up X using xf86-video-modesetting. It doesn't support the 3D accelerator or power management yet. v2: Drop FB_HELPER select thanks to Archit's patches. Do manual init ordering instead of using the .load hook. Structure registration more like tegra's, but still using the typical "component" code. Drop no-op hooks for atomic_begin and mode_fixup() now that they're optional. Drop sentinel in Makefile. Fix minor style nits I noticed on another reread. v3: Use the new bcm2835 clk driver to manage pixel/HSM clocks instead of having a fixed video mode. Use exynos-style component driver matching instead of devicetree nodes to list the component driver instances. Rename compatibility strings to say bcm2835, and distinguish pv0/1/2. Clean up some h/vsync code, and add in interlaced mode setup. Fix up probe/bind error paths. Use bitops.h macros for vc4_regs.h v4: Include i2c.h, allow building under COMPILE_TEST, drop msleep now that other bugs have been fixed, add timeouts to cpu_relax() loops, rename hpd-gpio to hpd-gpios. Signed-off-by: -
Eric Anholt authored
VC4 is the GPU (display and 3D) subsystem present on the 2835 and some other Broadcom SoCs. This binding follows the model of msm, imx, sti, and others, where there is a subsystem node for the whole GPU, with nodes for the individual HW components within it. v2: Extend the commit message, fix several nits from Stephen Warren. v3: Rename the compatibility strings, clean up node names, drop the unnecessary lists of components. Use compatibility strings for choosing CRTC HVS channel numbers. Document the HDMI clock usage. v4: Whitespace fix, expand acronyms, move to display/ instead of gpu/, rename "hpd-gpio" to "hpd-gpios". Signed-off-by:
-
- 19 Oct, 2015 21 commits
-
-
git://anongit.freedesktop.org/drm-intelDave Airlie authored
More drm-misc for 4.4. - fb refcount fix in atomic fbdev - various locking reworks to reduce drm_global_mutex and dev->struct_mutex - rename docbook to gpu.tmpl and include vga_switcheroo stuff, plus more vga_switcheroo (Lukas Wunner) - viewport check fixes for atomic drivers from Ville - DRM_DEBUG_VBL from Ville - non-contentious header fixes from Mikko Rapeli - small things all over * tag 'topic/drm-misc-2015-10-19' of git://anongit.freedesktop.org/drm-intel: (31 commits) drm/fb-helper: Fix fb refcounting in pan_display_atomic drm/fb-helper: Set plane rotation directly drm: fix mutex leak in drm_dp_get_mst_branch_device drm: Check plane src coordinates correctly during page flip for atomic drivers drm: Check crtc viewport correctly with rotated primary plane on atomic drivers drm: Refactor plane src coordinate checks drm: Swap w/h when converting the mode to src coordidates for a rotated primary plane drm: Don't leak fb when plane crtc coodinates are bad ALSA: hda - Spell vga_switcheroo consistently drm/gem: Use kref_get_unless_zero for the weak mmap references drm/vgem: Drop vgem_drm_gem_mmap drm: Fix return value of drm_framebuffer_init() drm/gem: Use container_of in drm_gem_object_free drm/gem: Check locking in drm_gem_object_unreference drm/gem: Drop struct_mutex requirement from drm_gem_mmap_obj drm/i810_drm.h: include drm/drm.h r128_drm.h: include drm/drm.h savage_drm.h: include <drm/drm.h> gpu/doc: Convert to markdown harder gpu/doc: Add vga_switcheroo documentation ...
-
git://anongit.freedesktop.org/drm-intelDave Airlie authored
- dmc fixes from Animesh (not yet all) for deeper sleep states - piles of prep patches from Ville to make mmio functions type-safe - more fbc work from Paulo all over - w/a shuffling from Arun Siluvery - first part of atomic watermark updates from Matt and Ville (later parts had to be dropped again unfortunately) - lots of patches to prepare bxt dsi support ( Shashank Sharma) - userptr fixes from Chris - audio rate interface between i915/snd_hda plus kerneldoc (Libin Yang) - shrinker improvements and fixes (Chris Wilson) - lots and lots of small patches all over * tag 'drm-intel-next-2015-10-10' of git://anongit.freedesktop.org/drm-intel: (134 commits) drm/i915: Update DRIVER_DATE to 20151010 drm/i915: Partial revert of atomic watermark series drm/i915: Early exit from semaphore_waits_for for execlist mode. drm/i915: Remove wrong warning from i915_gem_context_clean drm/i915: Determine the stolen memory base address on gen2 drm/i915: fix FBC buffer size checks drm/i915: fix CFB size calculation drm/i915: remove pre-atomic check from SKL update_primary_plane drm/i915: don't allocate fbcon from stolen memory if it's too big Revert "drm/i915: Call encoder hotplug for init and resume cases" Revert "drm/i915: Add hot_plug hook for hdmi encoder" drm/i915: use error path drm/i915/irq: Fix misspelled word register in kernel-doc drm/i915/irq: Fix kernel-doc warnings drm/i915: Hook up ring workaround writes at context creation time on Gen6-7. drm/i915: Don't warn if the workaround list is empty. drm/i915: Resurrect golden context on gen6/7 drm/i915/chv: remove pre-production hardware workarounds drm/i915/snb: remove pre-production hardware workaround drm/i915/bxt: Set time interval unit to 0.833us ...
-
git://linuxtv.org/pinchartl/fbdevDave Airlie authored
some rcar fixes. * 'drm/next/du' of git://linuxtv.org/pinchartl/fbdev: drm: rcar-du: Fix plane state free in plane reset handler drm: rcar-du: Enable DU0 to DPAD connection on R8A7791 drm: rcar-du: Add dependency on OF drm: rcar-du: Remove obsolete rcar-du-r8a779x platform_device_id entries
-
Laurent Pinchart authored
The plane reset handler frees the plane state and allocates a new default state, but when doing so attempt to free the plane state using the base plane state pointer instead of casting it to the driver-specific state object that has been allocated. Fix it by using the rcar_du_plane_atomic_destroy_state() function to destroy the plane state instead of duplicating the code. Signed-off-by:
Thierry Reding <treding@nvidia.com>
-
Laurent Pinchart authored
The DPAD RGB output can be driven by both DU0 and DU1 on R8A7791. Mark the DU0 connection as possible. Signed-off-by: -
Laurent Pinchart authored
The driver requires OF support, add a dependency in Kconfig and remove the platform_device_id table that isn't used anymore. Signed-off-by:
Geert Uytterhoeven <geert+renesas@glider.be>
-
Geert Uytterhoeven authored
Since commit a483dcbf ("ARM: shmobile: lager: Remove legacy board support"), R-Car Gen2 SoCs are only supported in generic DT-only ARM multi-platform builds. The driver doesn't need to match platform devices by name anymore, hence remove the corresponding platform_device_id entry. Signed-off-by:
-
Daniel Vetter authored
In commit bbb1e524 Author: Rob Clark <robdclark@gmail.com> Date: Tue Aug 25 15:35:58 2015 -0400 drm/fb-helper: atomic restore_fbdev_mode().. we've forgotten to do the plane->old_fb refcount dance for pan_display_atomic, which can result in refcount leaks if the current configuration is not from fbcon. Which apparently can happen when vt-switching - fbcon does a pan first before a set_par. OCD-align function parameters while at it. v2: Actually git add the OCD. Cc: Rob Clark <robdclark@gmail.com> Cc: Rodrigo Vivi <rodrigo.vivi@gmail.com> Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=92483Signed-off-by:
Daniel Vetter <daniel.vetter@intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1445015490-27682-1-git-send-email-daniel.vetter@ffwll.chTested-by:
Rodrigo Vivi <rodrigo.vivi@intel.com> Reviewed-by:
-
Daniel Vetter authored
The point behind standardizing properties into core drm state structures is also that internal code looks prettiers. Take advantage of that and set rotation directly in the fbdev atomic code. Cc: Rob Clark <robdclark@gmail.com> Signed-off-by:
-
Adam Richter authored
In Linux 4.3-rc5, there is an error case in drm_dp_get_branch_device that returns without releasing mgr->lock, resulting a spew of kernel messages about a kernel work function possibly having leaked a mutex and presumably more serious adverse consequences later. This patch changes the error to "goto out" to unlock the mutex before returning. Signed-off-by:
Adam J. Richter <adam_richter2004@yahoo.com> Signed-off-by:
-
Ville Syrjälä authored
Instead of relying on the old crtc-{x,y,mode} gunk, dig out the primary plane coordinates from the plane state when checking them against the new framebuffer during page flip. Cc: Matt Roper <matthew.d.roper@intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com> Cc: Daniel Vetter <daniel@ffwll.ch> Signed-off-by:Ville Syrjälä <ville.syrjala@linux.intel.com> Link: http://patchwork.freedesktop.org/patch/msgid/1444930802-8515-5-git-send-email-ville.syrjala@linux.intel.comReviewed-by:
Matt Roper <matthew.d.roper@intel.com> Signed-off-by:
-
Ville Syrjälä authored
On atomic drivers we can dig out the primary plane rotation from the plane state instead of looking at the legacy crtc->invert_dimensions flag. The flag is not set by anyone except omapdrm, and it would be racy to set it the same way in the atomic helpers. v2: Kill crtc->invert_dimensions totally since omap is state based already and no one else ever used it (Matt) Cc: Matt Roper <matthew.d.roper@intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Cc: Rob Clark <robdclark@gmail.com> Signed-off-by: -
Ville Syrjälä authored
Pull the plane src coordinate checks into a separate function so that we can share them for the legacy and new stuff. Cc: Matt Roper <matthew.d.roper@intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com> Cc: Daniel Vetter <daniel@ffwll.ch> Signed-off-by:
-
Ville Syrjälä authored
When converting the mode hdisplay/vdisplay to primary plane src coordinates we need to take into account the current plane rotation. Cc: Matt Roper <matthew.d.roper@intel.com> Cc: Tvrtko Ursulin <tvrtko.ursulin@linux.intel.com> Cc: Daniel Vetter <daniel@ffwll.ch> Signed-off-by:
-
Ville Syrjälä authored
Signed-off-by:
-
Lukas Wunner authored
Currently everyone and their dog has their own favourite spelling for vga_switcheroo. This makes it hard to grep dmesg for log entries relating to vga_switcheroo. It also makes it hard to find related source files in the tree. vga_switcheroo.c uses pr_fmt "vga_switcheroo". Use that everywhere. Signed-off-by:
Lukas Wunner <lukas@wunner.de> Reviewed-by:
Takashi Iwai <tiwai@suse.de> Link: http://patchwork.freedesktop.org/patch/msgid/9b0175319ce78d831acfcf11e4c6c760f826b0e3.1444663039.git.lukas@wunner.deSigned-off-by:
-
Daniel Vetter authored
Compared to wrapping the final kref_put with dev->struct_mutex this allows us to only acquire the offset manager look both in the final cleanup and in the lookup. Which has the upside that no locks leak out of the core abstractions. But it means that we need to hold a temporary reference to the object while checking mmap constraints, to make sure the object doesn't disappear. Extended the critical region would have worked too, but would result in more leaky locking. Also, this is the final bit which required dev->struct_mutex in gem core, now modern drivers can be completely struct_mutex free! This needs a new drm_vma_offset_exact_lookup_locked and makes both drm_vma_offset_exact_lookup and drm_vma_offset_lookup unused. v2: Don't leak object references in failure paths (David). v3: Add a comment from Chris explaining how the ordering works, with the slight adjustment that I dropped any mention of struct_mutex since with this patch it's now immaterial ot core gem. Cc: David Herrmann <dh.herrmann@gmail.com> Reviewed-by:
David Herrmann <dh.herrmann@gmail.com> Reviewed-by:
Chris Wilson <chris@chris-wilson.co.uk> Link: http://mid.gmane.org/1444901623-18918-1-git-send-email-daniel.vetter@ffwll.chSigned-off-by:
-
Daniel Vetter authored
It's duplicating (without using some of the helpers) drm_gem_mmap with the addition that it can redirect to drm-buf mmap support. But prime import/export was dropped in commit 990ed272 Author: Rob Clark <robdclark@gmail.com> Date: Thu May 21 11:58:30 2015 -0400 drm/vgem: drop DRIVER_PRIME (v2) for now, so this is dead code. And since I want to rework the locking for drm_gem_mmap it seems simpler to de-dupe this code for now and then start over with the reworked one again, if we want to resurrect this all indeed. Signed-off-by:
-
Lukas Wunner authored
In its original version, drm_framebuffer_init() returned a negative int if drm_mode_object_get() failed (f453ba04, "DRM: add mode setting support"). This was accidentally disabled by commit 4b096ac1 ("drm: revamp locking around fb creation/destruction"). Thus, drm_framebuffer_init() pretends success if drm_mode_object_get() failed. Reinstate the original behaviour. Also fix erroneous kernel-doc of drm_mode_object_get(). Fixes: 4b096ac1 ("drm: revamp locking around fb creation/ destruction") Cc: Daniel Vetter <daniel.vetter@ffwll.ch> Signed-off-by:
-
Daniel Vetter authored
Just a random thing I spotted while reading code - better safe than sorry. Link: http://mid.gmane.org/1444894601-5200-11-git-send-email-daniel.vetter@ffwll.chReviewed-by:
-
Daniel Vetter authored
Pretty soon only some drivers will need dev->struct_mutex in their gem_free_object callbacks. Hence it's really important to make sure everything still keeps getting this right. v2: Don't check for locking before we check for non-NULL obj. Spotted by Dan Carpenter. Link: http://mid.gmane.org/1444894601-5200-10-git-send-email-daniel.vetter@ffwll.chReviewed-by:
-
- 18 Oct, 2015 1 commit
-
-
git://git.kraxel.org/linuxDave Airlie authored
Add 3D support to the virtio-gpu. * 'virtio-gpu-for-drm-next' of git://git.kraxel.org/linux: virtio-gpu: add page flip support virtio-gpu: mark as a render gpu virtio-gpu: add basic prime support virtio-gpu: add 3d/virgl support virtio-gpu: don't free things on ttm_bo_init failure virtio-gpu: wait for cursor updates finish virtio-gpu: add & use virtio_gpu_queue_fenced_ctrl_buffer virtio-gpu: add virtio_gpu_queue_ctrl_buffer_locked
-
- 16 Oct, 2015 1 commit
-
-
Daniel Vetter authored
Since commit 131e663b Author: Daniel Vetter <daniel.vetter@ffwll.ch> Date: Thu Jul 9 23:32:33 2015 +0200 drm/gem: rip out drm vma accounting for gem mmaps there is no need for this any more. v2: Fixup compile noise spotted by 0-day build. Link: http://mid.gmane.org/1444894601-5200-9-git-send-email-daniel.vetter@ffwll.chReviewed-by:
-
