In Scenario A and B below, as the delayed INIT_ACK always changes the peer
vtag, SCTP ct with the incorrect vtag may cause packet loss.

Scenario A: INIT_ACK is delayed until the peer receives its own INIT_ACK

  192.168.1.2 > 192.168.1.1: [INIT] [init tag: 1328086772]
    192.168.1.1 > 192.168.1.2: [INIT] [init tag: 1414468151]
    192.168.1.2 > 192.168.1.1: [INIT ACK] [init tag: 1328086772]
  192.168.1.1 > 192.168.1.2: [INIT ACK] [init tag: 1650211246] *
  192.168.1.2 > 192.168.1.1: [COOKIE ECHO]
    192.168.1.1 > 192.168.1.2: [COOKIE ECHO]
    192.168.1.2 > 192.168.1.1: [COOKIE ACK]

Scenario B: INIT_ACK is delayed until the peer completes its own handshake

  192.168.1.2 > 192.168.1.1: sctp (1) [INIT] [init tag: 3922216408]
    192.168.1.1 > 192.168.1.2: sctp (1) [INIT] [init tag: 144230885]
    192.168.1.2 > 192.168.1.1: sctp (1) [INIT ACK] [init tag: 3922216408]
    192.168.1.1 > 192.168.1.2: sctp (1) [COOKIE ECHO]
    192.168.1.2 > 192.168.1.1: sctp (1) [COOKIE ACK]
  192.168.1.1 > 192.168.1.2: sctp (1) [INIT ACK] [init tag: 3914796021] *

This patch fixes it as below:

In SCTP_CID_INIT processing:
- clear ct->proto.sctp.init[!dir] if ct->proto.sctp.init[dir] &&
  ct->proto.sctp.init[!dir]. (Scenario E)
- set ct->proto.sctp.init[dir].

In SCTP_CID_INIT_ACK processing:
- drop it if !ct->proto.sctp.init[!dir] && ct->proto.sctp.vtag[!dir] &&
  ct->proto.sctp.vtag[!dir] != ih->init_tag. (Scenario B, Scenario C)
- drop it if ct->proto.sctp.init[dir] && ct->proto.sctp.init[!dir] &&
  ct->proto.sctp.vtag[!dir] != ih->init_tag. (Scenario A)

In SCTP_CID_COOKIE_ACK processing:
- clear ct->proto.sctp.init[dir] and ct->proto.sctp.init[!dir].
  (Scenario D)

Also, it's important to allow the ct state to move forward with cookie_echo
and cookie_ack from the opposite dir for the collision scenarios.

There are also other Scenarios where it should allow the packet through,
addressed by the processing above:

Scenario C: new CT is created by INIT_ACK.

Scenario D: start INIT on the existing ESTABLISHED ct.

Scenario E: start INIT after the old collision on the existing ESTABLISHED
ct.

  192.168.1.2 > 192.168.1.1: sctp (1) [INIT] [init tag: 3922216408]
  192.168.1.1 > 192.168.1.2: sctp (1) [INIT] [init tag: 144230885]
  (both side are stopped, then start new connection again in hours)
  192.168.1.2 > 192.168.1.1: sctp (1) [INIT] [init tag: 242308742]

Fixes: 9fb9cbb1 ("[NETFILTER]: Add nf_conntrack subsystem.")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: Florian Westphal <fw@strlen.de>

nft can perform merging of adjacent payload requests.
This means that:

ether saddr 00:11 ... ether type 8021ad ...

is a single payload expression, for 8 bytes, starting at the
ethernet source offset.

Check that offset+length is fully within the source/destination mac
addersses.

This bug prevents 'ether type' from matching the correct h_proto in case
vlan tag got stripped.

Fixes: de6843be ("netfilter: nft_payload: rebuild vlan header when needed")
Reported-by: David Ward <david.ward@ll.mit.edu>
Signed-off-by: Florian Westphal <fw@strlen.de>

In some OVS environments the TCP pseudo header checksum may need to be
recomputed. Currently this is only done when the interface instance is
configured for "Trunk Mode". We found the issue also occurs in some
Kubernetes environments, these environments do not use "Trunk Mode",
therefor the condition is removed.

Performance tests with this change show only a fractional decrease in
throughput (< 0.2%).

Fixes: 7525de25 ("ibmveth: Set CHECKSUM_PARTIAL if NULL TCP CSUM.")
Signed-off-by: David Wilder <dwilder@us.ibm.com>
Reviewed-by: Nick Child <nnac123@linux.ibm.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

The k3_udma_glue_tx_get_irq() function currently returns negative error
codes on error, zero on error and positive values for success.  This
complicates life for the callers who need to propagate the error code.
Also GCC will not warn about unsigned comparisons when you check:

	if (unsigned_irq <= 0)

All the callers have been fixed now but let's just make this easy going
forward.
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Acked-by: Vinod Koul <vkoul@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

The "tx_chn->irq" variable is unsigned so the error checking does not
work correctly.

Fixes: 128d5874 ("net: ti: icssg-prueth: Add ICSSG ethernet driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

This accidentally returns success, but it should return a negative error
code.

Fixes: 93a76530 ("net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Reviewed-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

In the while loop of vringh_iov_xfer(), `partlen` could be 0 if one of
the `iov` has 0 lenght.
In this case, we should skip the iov and go to the next one.
But calling vringh_kiov_advance() with 0 lenght does not cause the
advancement, since it returns immediately if asked to advance by 0 bytes.

Let's restore the code that was there before commit b8c06ad4
("vringh: implement vringh_kiov_advance()"), avoiding using
vringh_kiov_advance().

Fixes: b8c06ad4 ("vringh: implement vringh_kiov_advance()")
Cc: stable@vger.kernel.org
Reported-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

Fix the MPIC.PSMCS value following the programming example in the
section 6.4.2 Management Data Clock (MDC) Setting, Ethernet MAC IP,
S4 Hardware User Manual Rev.1.00.

The value is calculated by
    MPIC.PSMCS = clk[MHz] / (MDC frequency[MHz] * 2) - 1
with the input clock frequency from clk_get_rate() and MDC frequency
of 2.5MHz. Otherwise, this driver cannot communicate PHYs on the R-Car
S4 Starter Kit board.

Fixes: 3590918b ("net: ethernet: renesas: Add support for "Ethernet Switch"")
Reported-by: Tam Nguyen <tam.nguyen.xa@renesas.com>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Tested-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230926123054.3976752-1-yoshihiro.shimoda.uh@renesas.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The device list needs its associated lock held when modifying it, or the
list could become corrupted, as syzbot discovered.

Reported-and-tested-by: syzbot+c1d0a03d305972dbbe14@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=c1d0a03d305972dbbe14Signed-off-by: Jeremy Cline <jeremy@jcline.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Fixes: 6709d4b7 ("net: nfc: Fix use-after-free caused by nfc_llcp_find_local")
Link: https://lore.kernel.org/r/20230908235853.1319596-1-jeremy@jcline.orgSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The ETHTOOL_A_PLCA_ENABLED data type is u8. But while parsing the
value from the attribute, nla_get_u32() is used in the plca_update_sint()
function instead of nla_get_u8(). So plca_cfg.enabled variable is updated
with some garbage value instead of 0 or 1 and always enables plca even
though plca is disabled through ethtool application. This bug has been
fixed by parsing the values based on the attributes type in the policy.

Fixes: 8580e16c ("net/ethtool: add netlink interface for the PLCA RS")
Signed-off-by: Parthiban Veerasooran <Parthiban.Veerasooran@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230908044548.5878-1-Parthiban.Veerasooran@microchip.comSigned-off-by: Jakub Kicinski <kuba@kernel.org>

The flexible structure (a structure that contains a flexible-array member
at the end) `qed_ll2_tx_packet` is nested within the second layer of
`struct qed_ll2_info`:

struct qed_ll2_tx_packet {
	...
        /* Flexible Array of bds_set determined by max_bds_per_packet */
        struct {
                struct core_tx_bd *txq_bd;
                dma_addr_t tx_frag;
                u16 frag_len;
        } bds_set[];
};

struct qed_ll2_tx_queue {
	...
	struct qed_ll2_tx_packet cur_completing_packet;
};

struct qed_ll2_info {
	...
	struct qed_ll2_tx_queue tx_queue;
        struct qed_ll2_cbs cbs;
};

The problem is that member `cbs` in `struct qed_ll2_info` is placed just
after an object of type `struct qed_ll2_tx_queue`, which is in itself
an implicit flexible structure, which by definition ends in a flexible
array member, in this case `bds_set`. This causes an undefined behavior
bug at run-time when dynamic memory is allocated for `bds_set`, which
could lead to a serious issue if `cbs` in `struct qed_ll2_info` is
overwritten by the contents of `bds_set`. Notice that the type of `cbs`
is a structure full of function pointers (and a cookie :) ):

include/linux/qed/qed_ll2_if.h:
107 typedef
108 void (*qed_ll2_complete_rx_packet_cb)(void *cxt,
109                                       struct qed_ll2_comp_rx_data *data);
110
111 typedef
112 void (*qed_ll2_release_rx_packet_cb)(void *cxt,
113                                      u8 connection_handle,
114                                      void *cookie,
115                                      dma_addr_t rx_buf_addr,
116                                      bool b_last_packet);
117
118 typedef
119 void (*qed_ll2_complete_tx_packet_cb)(void *cxt,
120                                       u8 connection_handle,
121                                       void *cookie,
122                                       dma_addr_t first_frag_addr,
123                                       bool b_last_fragment,
124                                       bool b_last_packet);
125
126 typedef
127 void (*qed_ll2_release_tx_packet_cb)(void *cxt,
128                                      u8 connection_handle,
129                                      void *cookie,
130                                      dma_addr_t first_frag_addr,
131                                      bool b_last_fragment, bool b_last_packet);
132
133 typedef
134 void (*qed_ll2_slowpath_cb)(void *cxt, u8 connection_handle,
135                             u32 opaque_data_0, u32 opaque_data_1);
136
137 struct qed_ll2_cbs {
138         qed_ll2_complete_rx_packet_cb rx_comp_cb;
139         qed_ll2_release_rx_packet_cb rx_release_cb;
140         qed_ll2_complete_tx_packet_cb tx_comp_cb;
141         qed_ll2_release_tx_packet_cb tx_release_cb;
142         qed_ll2_slowpath_cb slowpath_cb;
143         void *cookie;
144 };

Fix this by moving the declaration of `cbs` to the  middle of its
containing structure `qed_ll2_info`, preventing it from being
overwritten by the contents of `bds_set` at run-time.

This bug was introduced in 2017, when `bds_set` was converted to a
one-element array, and started to be used as a Variable Length Object
(VLO) at run-time.

Fixes: f5823fe6 ("qed: Add ll2 option to limit the number of bds per packet")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/ZQ+Nz8DfPg56pIzr@workSigned-off-by: Paolo Abeni <pabeni@redhat.com>

syzbot reported the following uninit-value access issue:

=====================================================
BUG: KMSAN: uninit-value in smsc75xx_wait_ready drivers/net/usb/smsc75xx.c:975 [inline]
BUG: KMSAN: uninit-value in smsc75xx_bind+0x5c9/0x11e0 drivers/net/usb/smsc75xx.c:1482
CPU: 0 PID: 8696 Comm: kworker/0:3 Not tainted 5.8.0-rc5-syzkaller #0
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
 __dump_stack lib/dump_stack.c:77 [inline]
 dump_stack+0x21c/0x280 lib/dump_stack.c:118
 kmsan_report+0xf7/0x1e0 mm/kmsan/kmsan_report.c:121
 __msan_warning+0x58/0xa0 mm/kmsan/kmsan_instr.c:215
 smsc75xx_wait_ready drivers/net/usb/smsc75xx.c:975 [inline]
 smsc75xx_bind+0x5c9/0x11e0 drivers/net/usb/smsc75xx.c:1482
 usbnet_probe+0x1152/0x3f90 drivers/net/usb/usbnet.c:1737
 usb_probe_interface+0xece/0x1550 drivers/usb/core/driver.c:374
 really_probe+0xf20/0x20b0 drivers/base/dd.c:529
 driver_probe_device+0x293/0x390 drivers/base/dd.c:701
 __device_attach_driver+0x63f/0x830 drivers/base/dd.c:807
 bus_for_each_drv+0x2ca/0x3f0 drivers/base/bus.c:431
 __device_attach+0x4e2/0x7f0 drivers/base/dd.c:873
 device_initial_probe+0x4a/0x60 drivers/base/dd.c:920
 bus_probe_device+0x177/0x3d0 drivers/base/bus.c:491
 device_add+0x3b0e/0x40d0 drivers/base/core.c:2680
 usb_set_configuration+0x380f/0x3f10 drivers/usb/core/message.c:2032
 usb_generic_driver_probe+0x138/0x300 drivers/usb/core/generic.c:241
 usb_probe_device+0x311/0x490 drivers/usb/core/driver.c:272
 really_probe+0xf20/0x20b0 drivers/base/dd.c:529
 driver_probe_device+0x293/0x390 drivers/base/dd.c:701
 __device_attach_driver+0x63f/0x830 drivers/base/dd.c:807
 bus_for_each_drv+0x2ca/0x3f0 drivers/base/bus.c:431
 __device_attach+0x4e2/0x7f0 drivers/base/dd.c:873
 device_initial_probe+0x4a/0x60 drivers/base/dd.c:920
 bus_probe_device+0x177/0x3d0 drivers/base/bus.c:491
 device_add+0x3b0e/0x40d0 drivers/base/core.c:2680
 usb_new_device+0x1bd4/0x2a30 drivers/usb/core/hub.c:2554
 hub_port_connect drivers/usb/core/hub.c:5208 [inline]
 hub_port_connect_change drivers/usb/core/hub.c:5348 [inline]
 port_event drivers/usb/core/hub.c:5494 [inline]
 hub_event+0x5e7b/0x8a70 drivers/usb/core/hub.c:5576
 process_one_work+0x1688/0x2140 kernel/workqueue.c:2269
 worker_thread+0x10bc/0x2730 kernel/workqueue.c:2415
 kthread+0x551/0x590 kernel/kthread.c:292
 ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:293

Local variable ----buf.i87@smsc75xx_bind created at:
 __smsc75xx_read_reg drivers/net/usb/smsc75xx.c:83 [inline]
 smsc75xx_wait_ready drivers/net/usb/smsc75xx.c:968 [inline]
 smsc75xx_bind+0x485/0x11e0 drivers/net/usb/smsc75xx.c:1482
 __smsc75xx_read_reg drivers/net/usb/smsc75xx.c:83 [inline]
 smsc75xx_wait_ready drivers/net/usb/smsc75xx.c:968 [inline]
 smsc75xx_bind+0x485/0x11e0 drivers/net/usb/smsc75xx.c:1482

This issue is caused because usbnet_read_cmd() reads less bytes than requested
(zero byte in the reproducer). In this case, 'buf' is not properly filled.

This patch fixes the issue by returning -ENODATA if usbnet_read_cmd() reads
less bytes than requested.

Fixes: d0cad871 ("smsc75xx: SMSC LAN75xx USB gigabit ethernet adapter driver")
Reported-and-tested-by: syzbot+6966546b78d050bb0b5d@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=6966546b78d050bb0b5dSigned-off-by: Shigeru Yoshida <syoshida@redhat.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://lore.kernel.org/r/20230923173549.3284502-1-syoshida@redhat.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Commit b0e214d2 ("netfilter: keep conntrack reference until
IPsecv6 policy checks are done") is a direct copy of the old
commit b59c2701 ("[NETFILTER]: Keep conntrack reference until
IPsec policy checks are done") but for IPv6.  However, it also
copies a bug that this old commit had.  That is: when the third
packet of 3WHS connection establishment contains payload, it is
added into socket receive queue without the XFRM check and the
drop of connection tracking context.

That leads to nf_conntrack module being impossible to unload as
it waits for all the conntrack references to be dropped while
the packet release is deferred in per-cpu cache indefinitely, if
not consumed by the application.

The issue for IPv4 was fixed in commit 6f0012e3 ("tcp: add a
missing nf_reset_ct() in 3WHS handling") by adding a missing XFRM
check and correctly dropping the conntrack context.  However, the
issue was introduced to IPv6 code afterwards.  Fixing it the
same way for IPv6 now.

Fixes: b0e214d2 ("netfilter: keep conntrack reference until IPsecv6 policy checks are done")
Link: https://lore.kernel.org/netdev/d589a999-d4dd-2768-b2d5-89dec64a4a42@ovn.org/Signed-off-by: Ilya Maximets <i.maximets@ovn.org>
Acked-by: Florian Westphal <fw@strlen.de>
Reviewed-by: Eric Dumazet <edumazet@google.com>
Link: https://lore.kernel.org/r/20230922210530.2045146-1-i.maximets@ovn.orgSigned-off-by: Paolo Abeni <pabeni@redhat.com>

After deleting an interface address in fib_del_ifaddr(), the function
scans the fib_info list for stray entries and calls fib_flush() and
fib_table_flush(). Then the stray entries will be deleted silently and no
RTM_DELROUTE notification will be sent.

This lack of notification can make routing daemons, or monitor like
`ip monitor route` miss the routing changes. e.g.

+ ip link add dummy1 type dummy
+ ip link add dummy2 type dummy
+ ip link set dummy1 up
+ ip link set dummy2 up
+ ip addr add 192.168.5.5/24 dev dummy1
+ ip route add 7.7.7.0/24 dev dummy2 src 192.168.5.5
+ ip -4 route
7.7.7.0/24 dev dummy2 scope link src 192.168.5.5
192.168.5.0/24 dev dummy1 proto kernel scope link src 192.168.5.5
+ ip monitor route
+ ip addr del 192.168.5.5/24 dev dummy1
Deleted 192.168.5.0/24 dev dummy1 proto kernel scope link src 192.168.5.5
Deleted broadcast 192.168.5.255 dev dummy1 table local proto kernel scope link src 192.168.5.5
Deleted local 192.168.5.5 dev dummy1 table local proto kernel scope host src 192.168.5.5

As Ido reminded, fib_table_flush() isn't only called when an address is
deleted, but also when an interface is deleted or put down. The lack of
notification in these cases is deliberate. And commit 7c6bb7d2
("net/ipv6: Add knob to skip DELROUTE message on device down") introduced
a sysctl to make IPv6 behave like IPv4 in this regard. So we can't send
the route delete notify blindly in fib_table_flush().

To fix this issue, let's add a new flag in "struct fib_info" to track the
deleted prefer source address routes, and only send notify for them.

After update:
+ ip monitor route
+ ip addr del 192.168.5.5/24 dev dummy1
Deleted 192.168.5.0/24 dev dummy1 proto kernel scope link src 192.168.5.5
Deleted broadcast 192.168.5.255 dev dummy1 table local proto kernel scope link src 192.168.5.5
Deleted local 192.168.5.5 dev dummy1 table local proto kernel scope host src 192.168.5.5
Deleted 7.7.7.0/24 dev dummy2 scope link src 192.168.5.5
Suggested-by: Thomas Haller <thaller@redhat.com>
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Acked-by: Nicolas Dichtel <nicolas.dichtel@6wind.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Link: https://lore.kernel.org/r/20230922075508.848925-1-liuhangbin@gmail.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

In the pathological case of building sky2 with 16k PAGE_SIZE, the
frag_addr[] array would never be used, so the original code was correct
that size should be 0. But the compiler now gets upset with 0 size arrays
in places where it hasn't eliminated the code that might access such an
array (it can't figure out that in this case an rx skb with fragments
would never be created). To keep the compiler happy, make sure there is
at least 1 frag_addr in struct rx_ring_info:

   In file included from include/linux/skbuff.h:28,
                    from include/net/net_namespace.h:43,
                    from include/linux/netdevice.h:38,
                    from drivers/net/ethernet/marvell/sky2.c:18:
   drivers/net/ethernet/marvell/sky2.c: In function 'sky2_rx_unmap_skb':
   include/linux/dma-mapping.h:416:36: warning: array subscript i is outside array bounds of 'dma_addr_t[0]' {aka 'long long unsigned int[]'} [-Warray-bounds=]
     416 | #define dma_unmap_page(d, a, s, r) dma_unmap_page_attrs(d, a, s, r, 0)
         |                                    ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
   drivers/net/ethernet/marvell/sky2.c:1257:17: note: in expansion of macro 'dma_unmap_page'
    1257 |                 dma_unmap_page(&pdev->dev, re->frag_addr[i],
         |                 ^~~~~~~~~~~~~~
   In file included from drivers/net/ethernet/marvell/sky2.c:41:
   drivers/net/ethernet/marvell/sky2.h:2198:25: note: while referencing 'frag_addr'
    2198 |         dma_addr_t      frag_addr[ETH_JUMBO_MTU >> PAGE_SHIFT];
         |                         ^~~~~~~~~

With CONFIG_PAGE_SIZE_16KB=y, PAGE_SHIFT == 14, so:

  #define ETH_JUMBO_MTU   9000

causes "ETH_JUMBO_MTU >> PAGE_SHIFT" to be 0. Use "?: 1" to solve this build warning.

Cc: Mirko Lindner <mlindner@marvell.com>
Cc: Stephen Hemminger <stephen@networkplumber.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Paolo Abeni <pabeni@redhat.com>
Cc: netdev@vger.kernel.org
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202309191958.UBw1cjXk-lkp@intel.com/Reviewed-by: Alexander Lobakin <aleksander.lobakin@intel.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Gustavo A. R. Silva <gustavoars@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Since commit 23d775f1 ("net: dsa: mv88e6xxx: Wait for EEPROM done
before HW reset") the following error is seen on a imx8mn board with
a 88E6320 switch:

mv88e6085 30be0000.ethernet-1:00: Timeout waiting for EEPROM done

This board does not have an EEPROM attached to the switch though.

This problem is well explained by Andrew Lunn:

"If there is an EEPROM, and the EEPROM contains a lot of data, it could
be that when we perform a hardware reset towards the end of probe, it
interrupts an I2C bus transaction, leaving the I2C bus in a bad state,
and future reads of the EEPROM do not work.

The work around for this was to poll the EEInt status and wait for it
to go true before performing the hardware reset.

However, we have discovered that for some boards which do not have an
EEPROM, EEInt never indicates complete. As a result,
mv88e6xxx_g1_wait_eeprom_done() spins for a second and then prints a
warning.

We probably need a different solution than calling
mv88e6xxx_g1_wait_eeprom_done(). The datasheet for 6352 documents the
EEPROM Command register:

bit 15 is:

  EEPROM Unit Busy. This bit must be set to a one to start an EEPROM
  operation (see EEOp below). Only one EEPROM operation can be
  executing at one time so this bit must be zero before setting it to
  a one.  When the requested EEPROM operation completes this bit will
  automatically be cleared to a zero. The transition of this bit from
  a one to a zero can be used to generate an interrupt (the EEInt in
  Global 1, offset 0x00).

and more interesting is bit 11:

  Register Loader Running. This bit is set to one whenever the
  register loader is busy executing instructions contained in the
  EEPROM."

Change to using mv88e6xxx_g2_eeprom_wait() to fix the timeout error
when the EEPROM chip is not present.

Fixes: 23d775f1 ("net: dsa: mv88e6xxx: Wait for EEPROM done before HW reset")
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Fabio Estevam <festevam@denx.de>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

When device_add() fails, ptp_ocp_dev_release() will be called
after put_device(). Therefore, it seems that the
ptp_ocp_dev_release() before put_device() is redundant.

Fixes: 773bda96 ("ptp: ocp: Expose various resources on the timecard.")
Signed-off-by: Dinghao Liu <dinghao.liu@zju.edu.cn>
Reviewed-by: Vadim Feodrenko <vadim.fedorenko@linux.dev>
Signed-off-by: David S. Miller <davem@davemloft.net>

Similar to the change in commit 0bdf3993("net: Avoid address
overwrite in kernel_connect"), BPF hooks run on bind may rewrite the
address passed to kernel_bind(). This change

1) Makes a copy of the bind address in kernel_bind() to insulate
   callers.
2) Replaces direct calls to sock->ops->bind() in net with kernel_bind()

Link: https://lore.kernel.org/netdev/20230912013332.2048422-1-jrife@google.com/
Fixes: 4fbac77d ("bpf: Hooks for sys_bind")
Cc: stable@vger.kernel.org
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jordan Rife <jrife@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Callers of sock_sendmsg(), and similarly kernel_sendmsg(), in kernel
space may observe their value of msg_name change in cases where BPF
sendmsg hooks rewrite the send address. This has been confirmed to break
NFS mounts running in UDP mode and has the potential to break other
systems.

This patch:

1) Creates a new function called __sock_sendmsg() with same logic as the
   old sock_sendmsg() function.
2) Replaces calls to sock_sendmsg() made by __sys_sendto() and
   __sys_sendmsg() with __sock_sendmsg() to avoid an unnecessary copy,
   as these system calls are already protected.
3) Modifies sock_sendmsg() so that it makes a copy of msg_name if
   present before passing it down the stack to insulate callers from
   changes to the send address.

Link: https://lore.kernel.org/netdev/20230912013332.2048422-1-jrife@google.com/
Fixes: 1cedee13 ("bpf: Hooks for sys_sendmsg")
Cc: stable@vger.kernel.org
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jordan Rife <jrife@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

commit 0bdf3993 ("net: Avoid address overwrite in kernel_connect")
ensured that kernel_connect() will not overwrite the address parameter
in cases where BPF connect hooks perform an address rewrite. This change
replaces direct calls to sock->ops->connect() in net with kernel_connect()
to make these call safe.

Link: https://lore.kernel.org/netdev/20230912013332.2048422-1-jrife@google.com/
Fixes: d74bad4e ("bpf: Hooks for sys_connect")
Cc: stable@vger.kernel.org
Reviewed-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jordan Rife <jrife@google.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

Including the transhdrlen in length is a problem when the packet is
partially filled (e.g. something like send(MSG_MORE) happened previously)
when appending to an IPv4 or IPv6 packet as we don't want to repeat the
transport header or account for it twice.  This can happen under some
circumstances, such as splicing into an L2TP socket.

The symptom observed is a warning in __ip6_append_data():

    WARNING: CPU: 1 PID: 5042 at net/ipv6/ip6_output.c:1800 __ip6_append_data.isra.0+0x1be8/0x47f0 net/ipv6/ip6_output.c:1800

that occurs when MSG_SPLICE_PAGES is used to append more data to an already
partially occupied skbuff.  The warning occurs when 'copy' is larger than
the amount of data in the message iterator.  This is because the requested
length includes the transport header length when it shouldn't.  This can be
triggered by, for example:

        sfd = socket(AF_INET6, SOCK_DGRAM, IPPROTO_L2TP);
        bind(sfd, ...); // ::1
        connect(sfd, ...); // ::1 port 7
        send(sfd, buffer, 4100, MSG_MORE);
        sendfile(sfd, dfd, NULL, 1024);

Fix this by only adding transhdrlen into the length if the write queue is
empty in l2tp_ip6_sendmsg(), analogously to how UDP does things.

l2tp_ip_sendmsg() looks like it won't suffer from this problem as it builds
the UDP packet itself.

Fixes: a32e0eec ("l2tp: introduce L2TPv3 IP encapsulation support for IPv6")
Reported-by: syzbot+62cbf263225ae13ff153@syzkaller.appspotmail.com
Link: https://lore.kernel.org/r/0000000000001c12b30605378ce8@google.com/Suggested-by: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
cc: Eric Dumazet <edumazet@google.com>
cc: Willem de Bruijn <willemdebruijn.kernel@gmail.com>
cc: "David S. Miller" <davem@davemloft.net>
cc: David Ahern <dsahern@kernel.org>
cc: Paolo Abeni <pabeni@redhat.com>
cc: Jakub Kicinski <kuba@kernel.org>
cc: netdev@vger.kernel.org
cc: bpf@vger.kernel.org
cc: syzkaller-bugs@googlegroups.com
Reviewed-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

n->output field can be read locklessly, while a writer
might change the pointer concurrently.

Add missing annotations to prevent load-store tearing.

Fixes: 1da177e4 ("Linux-2.6.12-rc2")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

While looking at a related syzbot report involving neigh_periodic_work(),
I found that I forgot to add an annotation when deleting an
RCU protected item from a list.

Readers use rcu_deference(*np), we need to use either
rcu_assign_pointer() or WRITE_ONCE() on writer side
to prevent store tearing.

I use rcu_assign_pointer() to have lockdep support,
this was the choice made in neigh_flush_dev().

Fixes: 767e97e1 ("neigh: RCU conversion of struct neighbour")
Signed-off-by: Eric Dumazet <edumazet@google.com>
Reviewed-by: David Ahern <dsahern@kernel.org>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

bluetooth pull request for net:

 - Fix handling of HCI_QUIRK_STRICT_DUPLICATE_FILTER
 - Fix handling of listen for ISO unicast
 - Fix build warnings
 - Fix leaking content of local_codecs
 - Add shutdown function for QCA6174
 - Delete unused hci_req_prepare_suspend() declaration
 - Fix hci_link_tx_to RCU lock usage
 - Avoid redundant authentication
Signed-off-by: David S. Miller <davem@davemloft.net>

The second parameter of stmmac_pltfr_init() needs the pointer of
"struct plat_stmmacenet_data". So, correct the parameter typo when calling the
function.

Otherwise, it may cause this alignment exception when doing suspend/resume.
[   49.067201] CPU1 is up
[   49.135258] Internal error: SP/PC alignment exception: 000000008a000000 [#1] PREEMPT SMP
[   49.143346] Modules linked in: soc_imx9 crct10dif_ce polyval_ce nvmem_imx_ocotp_fsb_s400 polyval_generic layerscape_edac_mod snd_soc_fsl_asoc_card snd_soc_imx_audmux snd_soc_imx_card snd_soc_wm8962 el_enclave snd_soc_fsl_micfil rtc_pcf2127 rtc_pcf2131 flexcan can_dev snd_soc_fsl_xcvr snd_soc_fsl_sai imx8_media_dev(C) snd_soc_fsl_utils fuse
[   49.173393] CPU: 0 PID: 565 Comm: sh Tainted: G         C         6.5.0-rc4-next-20230804-05047-g5781a6249dae #677
[   49.183721] Hardware name: NXP i.MX93 11X11 EVK board (DT)
[   49.189190] pstate: 60400009 (nZCv daif +PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[   49.196140] pc : 0x80800052
[   49.198931] lr : stmmac_pltfr_resume+0x34/0x50
[   49.203368] sp : ffff800082f8bab0
[   49.206670] x29: ffff800082f8bab0 x28: ffff0000047d0ec0 x27: ffff80008186c170
[   49.213794] x26: 0000000b5e4ff1ba x25: ffff800081e5fa74 x24: 0000000000000010
[   49.220918] x23: ffff800081fe0000 x22: 0000000000000000 x21: 0000000000000000
[   49.228042] x20: ffff0000001b4010 x19: ffff0000001b4010 x18: 0000000000000006
[   49.235166] x17: ffff7ffffe007000 x16: ffff800080000000 x15: 0000000000000000
[   49.242290] x14: 00000000000000fc x13: 0000000000000000 x12: 0000000000000000
[   49.249414] x11: 0000000000000001 x10: 0000000000000a60 x9 : ffff800082f8b8c0
[   49.256538] x8 : 0000000000000008 x7 : 0000000000000001 x6 : 000000005f54a200
[   49.263662] x5 : 0000000001000000 x4 : ffff800081b93680 x3 : ffff800081519be0
[   49.270786] x2 : 0000000080800052 x1 : 0000000000000000 x0 : ffff0000001b4000
[   49.277911] Call trace:
[   49.280346]  0x80800052
[   49.282781]  platform_pm_resume+0x2c/0x68
[   49.286785]  dpm_run_callback.constprop.0+0x74/0x134
[   49.291742]  device_resume+0x88/0x194
[   49.295391]  dpm_resume+0x10c/0x230
[   49.298866]  dpm_resume_end+0x18/0x30
[   49.302515]  suspend_devices_and_enter+0x2b8/0x624
[   49.307299]  pm_suspend+0x1fc/0x348
[   49.310774]  state_store+0x80/0x104
[   49.314258]  kobj_attr_store+0x18/0x2c
[   49.318002]  sysfs_kf_write+0x44/0x54
[   49.321659]  kernfs_fop_write_iter+0x120/0x1ec
[   49.326088]  vfs_write+0x1bc/0x300
[   49.329485]  ksys_write+0x70/0x104
[   49.332874]  __arm64_sys_write+0x1c/0x28
[   49.336783]  invoke_syscall+0x48/0x114
[   49.340527]  el0_svc_common.constprop.0+0xc4/0xe4
[   49.345224]  do_el0_svc+0x38/0x98
[   49.348526]  el0_svc+0x2c/0x84
[   49.351568]  el0t_64_sync_handler+0x100/0x12c
[   49.355910]  el0t_64_sync+0x190/0x194
[   49.359567] Code: ???????? ???????? ???????? ???????? (????????)
[   49.365644] ---[ end trace 0000000000000000 ]---

Fixes: 97117eb5 ("net: stmmac: platform: provide stmmac_pltfr_init()")
Signed-off-by: Clark Wang <xiaoning.wang@nxp.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Serge Semin <fancer.lancer@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

When the PF and VF drivers both support flexible rx descriptors and have
negotiated the VIRTCHNL_VF_OFFLOAD_RX_FLEX_DESC capability, the VF driver
queries the PF for the list of supported descriptor formats
(VIRTCHNL_OP_GET_SUPPORTED_RXDIDS). The PF driver is supposed to set the
supported_rxdids bits that correspond to the descriptor formats the
firmware implements. The legacy 32-byte rx desc format is always
supported, even though it is not expressed in GLFLXP_RXDID_FLAGS.

The ice driver does not advertise the legacy 32-byte rx desc support,
which leads to this failure to bring up the VF using the Intel
out-of-tree iavf driver:
 iavf 0000:41:01.0: PF does not list support for default Rx descriptor format
 ...
 iavf 0000:41:01.0: PF returned error -5 (VIRTCHNL_STATUS_ERR_PARAM) to our request 6

The in-tree iavf driver does not expose this bug, because it does not
yet implement VIRTCHNL_VF_OFFLOAD_RX_FLEX_DESC.

The ice driver must always set the ICE_RXDID_LEGACY_1 bit in
supported_rxdids. The Intel out-of-tree ice driver and the ice driver in
DPDK both do this.

I copied this piece of the code and the comment text from the Intel
out-of-tree driver.

Fixes: e753df8f ("ice: Add support Flex RXD")
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Reviewed-by: Przemek Kitszel <przemyslaw.kitszel@intel.com>
Link: https://lore.kernel.org/r/20230920115439.61172-1-mschmidt@redhat.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Process the result of hdlc_open() and call uhdlc_close()
in case of an error. It is necessary to pass the error
code up the control flow, similar to a possible
error in request_irq().
Also add a hdlc_close() call to the uhdlc_close()
because the comment to hdlc_close() says it must be called
by the hardware driver when the HDLC device is being closed

Found by Linux Verification Center (linuxtesting.org) with SVACE.

Fixes: c19b6d24 ("drivers/net: support hdlc function for QE-UCC")
Signed-off-by: Alexandra Diupina <adiupina@astralinux.ru>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu>
Signed-off-by: David S. Miller <davem@davemloft.net>

Pull networking fixes from Paolo Abeni:
 "Including fixes from netfilter and bpf.

  Current release - regressions:

   - bpf: adjust size_index according to the value of KMALLOC_MIN_SIZE

   - netfilter: fix entries val in rule reset audit log

   - eth: stmmac: fix incorrect rxq|txq_stats reference

  Previous releases - regressions:

   - ipv4: fix null-deref in ipv4_link_failure

   - netfilter:
      - fix several GC related issues
      - fix race between IPSET_CMD_CREATE and IPSET_CMD_SWAP

   - eth: team: fix null-ptr-deref when team device type is changed

   - eth: i40e: fix VF VLAN offloading when port VLAN is configured

   - eth: ionic: fix 16bit math issue when PAGE_SIZE >= 64KB

  Previous releases - always broken:

   - core: fix ETH_P_1588 flow dissector

   - mptcp: fix several connection hang-up conditions

   - bpf:
      - avoid deadlock when using queue and stack maps from NMI
      - add override check to kprobe multi link attach

   - hsr: properly parse HSRv1 supervisor frames.

   - eth: igc: fix infinite initialization loop with early XDP redirect

   - eth: octeon_ep: fix tx dma unmap len values in SG

   - eth: hns3: fix GRE checksum offload issue"

* tag 'net-6.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (87 commits)
  sfc: handle error pointers returned by rhashtable_lookup_get_insert_fast()
  igc: Expose tx-usecs coalesce setting to user
  octeontx2-pf: Do xdp_do_flush() after redirects.
  bnxt_en: Flush XDP for bnxt_poll_nitroa0()'s NAPI
  net: ena: Flush XDP packets on error.
  net/handshake: Fix memory leak in __sock_create() and sock_alloc_file()
  net: hinic: Fix warning-hinic_set_vlan_fliter() warn: variable dereferenced before check 'hwdev'
  netfilter: ipset: Fix race between IPSET_CMD_CREATE and IPSET_CMD_SWAP
  netfilter: nf_tables: fix memleak when more than 255 elements expired
  netfilter: nf_tables: disable toggling dormant table state more than once
  vxlan: Add missing entries to vxlan_get_size()
  net: rds: Fix possible NULL-pointer dereference
  team: fix null-ptr-deref when team device type is changed
  net: bridge: use DEV_STATS_INC()
  net: hns3: add 5ms delay before clear firmware reset irq source
  net: hns3: fix fail to delete tc flower rules during reset issue
  net: hns3: only enable unicast promisc when mac table full
  net: hns3: fix GRE checksum offload issue
  net: hns3: add cmdq check for vf periodic service task
  net: stmmac: fix incorrect rxq|txq_stats reference
  ...

Pull finegrained timestamp reverts from Christian Brauner:
 "Earlier this week we sent a few minor fixes for the multi-grained
  timestamp work in [1]. While we were polishing those up after Linus
  realized that there might be a nicer way to fix them we received a
  regression report in [2] that fine grained timestamps break gnulib
  tests and thus possibly other tools.

  The kernel will elide fine-grain timestamp updates when no one is
  actively querying for them to avoid performance impacts. So a sequence
  like write(f1) stat(f2) write(f2) stat(f2) write(f1) stat(f1) may
  result in timestamp f1 to be older than the final f2 timestamp even
  though f1 was last written too but the second write didn't update the
  timestamp.

  Such plotholes can lead to subtle bugs when programs compare
  timestamps. For example, the nap() function in [2] will estimate that
  it needs to wait one ns on a fine-grain timestamp enabled filesytem
  between subsequent calls to observe a timestamp change. But in general
  we don't update timestamps with more than one jiffie if we think that
  no one is actively querying for fine-grain timestamps to avoid
  performance impacts.

  While discussing various fixes the decision was to go back to the
  drawing board and ultimately to explore a solution that involves only
  exposing such fine-grained timestamps to nfs internally and never to
  userspace.

  As there are multiple solutions discussed the honest thing to do here
  is not to fix this up or disable it but to cleanly revert. The general
  infrastructure will probably come back but there is no reason to keep
  this code in mainline.

  The general changes to timestamp handling are valid and a good cleanup
  that will stay. The revert is fully bisectable"

Link: https://lore.kernel.org/all/20230918-hirte-neuzugang-4c2324e7bae3@brauner [1]
Link: https://lore.kernel.org/all/bf0524debb976627693e12ad23690094e4514303.camel@linuxfromscratch.org [2]

* tag 'v6.6-rc3.vfs.ctime.revert' of git://git.kernel.org/pub/scm/linux/kernel/git/vfs/vfs:
  Revert "fs: add infrastructure for multigrain timestamps"
  Revert "btrfs: convert to multigrain timestamps"
  Revert "ext4: switch to multigrain timestamps"
  Revert "xfs: switch to multigrain timestamps"
  Revert "tmpfs: add support for multigrain timestamps"

Pull powerpc fixes from Michael Ellerman:

 - A fix for breakpoint handling which was using get_user() while atomic

 - Fix the Power10 HASHCHK handler which was using get_user() while
   atomic

 - A few build fixes for issues caused by recent changes

Thanks to Benjamin Gray, Christophe Leroy, Kajol Jain, and Naveen N Rao.

* tag 'powerpc-6.6-2' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
  powerpc/dexcr: Move HASHCHK trap handler
  powerpc/82xx: Select FSL_SOC
  powerpc: Fix build issue with LD_DEAD_CODE_DATA_ELIMINATION and FTRACE_MCOUNT_USE_PATCHABLE_FUNCTION_ENTRY
  powerpc/watchpoints: Annotate atomic context in more places
  powerpc/watchpoint: Disable pagefaults when getting user instruction
  powerpc/watchpoints: Disable preemption in thread_change_pc()
  powerpc/perf/hv-24x7: Update domain value check

Pull xen fixes from Juergen Gross:

 - remove some unused functions in the Xen event channel handling

 - fix a regression (introduced during the merge window) when booting as
   Xen PV guest

 - small cleanup removing another strncpy() instance

* tag 'for-linus-6.6a-rc3-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/xen/tip:
  xen/efi: refactor deprecated strncpy
  x86/xen: allow nesting of same lazy mode
  x86/xen: move paravirt lazy code
  arm/xen: remove lazy mode related definitions
  xen: simplify evtchn_do_upcall() call maze

Pull memblock test fixes from Mike Rapoport:
 "Fix several compilation errors and warnings in memblock tests"

* tag 'fixes-2023-09-21' of git://git.kernel.org/pub/scm/linux/kernel/git/rppt/memblock:
  memblock tests: fix warning ‘struct seq_file’ declared inside parameter list
  memblock tests: fix warning: "__ALIGN_KERNEL" redefined
  memblock tests: Fix compilation errors.

Pull sound fixes from Takashi Iwai:
 "A large collection of fixes around this time.

  All small and mostly trivial fixes.

   - Lots of fixes for the new -Wformat-truncation warnings

   - A fix in ALSA rawmidi core regression and UMP handling

   - Series of Cirrus codec fixes

   - ASoC Intel and Realtek codec fixes

   - Usual HD- and USB-audio quirks and AMD ASoC quirks"

* tag 'sound-6.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (64 commits)
  ALSA: hda/realtek - ALC287 Realtek I2S speaker platform support
  ALSA: hda: cs35l56: Use the new RUNTIME_PM_OPS() macro
  ALSA: usb-audio: scarlett_gen2: Fix another -Wformat-truncation warning
  ALSA: rawmidi: Fix NULL dereference at proc read
  ASoC: SOF: core: Only call sof_ops_free() on remove if the probe was successful
  ASoC: SOF: Intel: MTL: Reduce the DSP init timeout
  ASoC: cs42l43: Add shared IRQ flag for shutters
  ASoC: imx-audmix: Fix return error with devm_clk_get()
  ASoC: hdaudio.c: Add missing check for devm_kstrdup
  ALSA: riptide: Fix -Wformat-truncation warning for longname string
  ALSA: cs4231: Fix -Wformat-truncation warning for longname string
  ALSA: ad1848: Fix -Wformat-truncation warning for longname string
  ALSA: hda: generic: Check potential mixer name string truncation
  ALSA: cmipci: Fix -Wformat-truncation warning
  ALSA: firewire: Fix -Wformat-truncation warning for MIDI stream names
  ALSA: firewire: Fix -Wformat-truncation warning for longname string
  ALSA: xen: Fix -Wformat-truncation warning
  ALSA: opti9x: Fix -Wformat-truncation warning
  ALSA: es1688: Fix -Wformat-truncation warning
  ALSA: cs4236: Fix -Wformat-truncation warning
  ...

Merge tag 'hwmon-for-v6.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging

Pull hwmon fix from Guenter Roeck:
 "One patch to drop a non-existent alarm attribute in the nct6775 driver"

* tag 'hwmon-for-v6.6-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging:
  hwmon: (nct6775) Fix non-existent ALARM warning

Florian Westphal says:

====================
netfilter updates for net

The following three patches fix regressions in the netfilter subsystem:

1. Reject attempts to repeatedly toggle the 'dormant' flag in a single
   transaction.  Doing so makes nf_tables lose track of the real state
   vs. the desired state.  This ends with an attempt to unregister hooks
   that were never registered in the first place, which yields a splat.

2. Fix element counting in the new nftables garbage collection infra
   that came with 6.5:  More than 255 expired elements wraps a counter
   which results in memory leak.

3. Since 6.4 ipset can BUG when a set is renamed while a CREATE command
   is in progress, fix from Jozsef Kadlecsik.

* tag 'nf-23-09-20' of https://git.kernel.org/pub/scm/linux/kernel/git/netfilter/nf:
  netfilter: ipset: Fix race between IPSET_CMD_CREATE and IPSET_CMD_SWAP
  netfilter: nf_tables: fix memleak when more than 255 elements expired
  netfilter: nf_tables: disable toggling dormant table state more than once
====================

Link: https://lore.kernel.org/r/20230920084156.4192-1-fw@strlen.deSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Several places in TC offload code assumed that the return from
 rhashtable_lookup_get_insert_fast() was always either NULL or a valid
 pointer to an existing entry, but in fact that function can return an
 error pointer.  In that case, perform the usual cleanup of the newly
 created entry, then pass up the error, rather than attempting to take a
 reference on the old entry.

Fixes: d902e1a7 ("sfc: bare bones TC offload on EF100")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Edward Cree <ecree.xilinx@gmail.com>
Link: https://lore.kernel.org/r/20230919183949.59392-1-edward.cree@amd.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

When users attempt to obtain the coalesce setting using the
ethtool command, current code always returns 0 for tx-usecs.
This is because I225/6 always uses a queue pair setting, hence
tx_coalesce_usecs does not return a value during the
igc_ethtool_get_coalesce() callback process. The pair queue
condition checking in igc_ethtool_get_coalesce() is removed by
this patch so that the user gets information of the value of tx-usecs.

Even if i225/6 is using queue pair setting, there is no harm in
notifying the user of the tx-usecs. The implementation of the current
code may have previously been a copy of the legacy code i210.
Since I225 has the queue pair setting enabled, tx-usecs will always adhere
to the user-set rx-usecs value. An error message will appear when the user
attempts to set the tx-usecs value for the input parameters because,
by default, they should only set the rx-usecs value.

This patch also adds the helper function to get the
previous rx coalesce value similar to tx coalesce.

How to test:
User can get the coalesce value using ethtool command.

Example command:
Get: ethtool -c <interface>

Previous output:

rx-usecs: 3
rx-frames: n/a
rx-usecs-irq: n/a
rx-frames-irq: n/a

tx-usecs: 0
tx-frames: n/a
tx-usecs-irq: n/a
tx-frames-irq: n/a

New output:

rx-usecs: 3
rx-frames: n/a
rx-usecs-irq: n/a
rx-frames-irq: n/a

tx-usecs: 3
tx-frames: n/a
tx-usecs-irq: n/a
tx-frames-irq: n/a

Fixes: 8c5ad0da ("igc: Add ethtool support")
Signed-off-by: Muhammad Husaini Zulkifli <muhammad.husaini.zulkifli@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Link: https://lore.kernel.org/r/20230919170331.1581031-1-anthony.l.nguyen@intel.comSigned-off-by: Paolo Abeni <pabeni@redhat.com>

Sebastian Andrzej Siewior says:

====================
Add missing xdp_do_flush() invocations.

I've been looking at the drivers/ XDP users and noticed that some
XDP_REDIRECT user don't invoke xdp_do_flush() at the end.
====================

Link: https://lore.kernel.org/r/20230918153611.165722-1-bigeasy@linutronix.deSigned-off-by: Paolo Abeni <pabeni@redhat.com>

xdp_do_flush() should be invoked before leaving the NAPI poll function
if XDP-redirect has been performed.

Invoke xdp_do_flush() before leaving NAPI.

Cc: Geetha sowjanya <gakula@marvell.com>
Cc: Subbaraya Sundeep <sbhatta@marvell.com>
Cc: Sunil Goutham <sgoutham@marvell.com>
Cc: hariprasad <hkelam@marvell.com>
Fixes: 06059a1a ("octeontx2-pf: Add XDP support to netdev PF")
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Geethasowjanya Akula <gakula@marvell.com>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

bnxt_poll_nitroa0() invokes bnxt_rx_pkt() which can run a XDP program
which in turn can return XDP_REDIRECT. bnxt_rx_pkt() is also used by
__bnxt_poll_work() which flushes (xdp_do_flush()) the packets after each
round. bnxt_poll_nitroa0() lacks this feature.
xdp_do_flush() should be invoked before leaving the NAPI callback.

Invoke xdp_do_flush() after a redirect in bnxt_poll_nitroa0() NAPI.

Cc: Michael Chan <michael.chan@broadcom.com>
Fixes: f18c2b77 ("bnxt_en: optimized XDP_REDIRECT support")
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Jesper Dangaard Brouer <hawk@kernel.org>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>