- 21 Apr, 2012 29 commits
-
-
Richard Cochran authored
The time stamping code in this driver appears to have been copied from the ixp4xx_eth.c driver, including this timing comment. I had actually measured the time stamp delay on an IXP425, but I really doubt that this value also applies here. Signed-off-by:
Richard Cochran <richardcochran@gmail.com> Signed-off-by:
David S. Miller <davem@davemloft.net>
-
Richard Cochran authored
This patch fixes code which needlessly ran the BPF twice per packet. Instead, we just run the classifier once and test whether the packet is any kind of PTP event message. Signed-off-by:
-
Takahiro Shimizu authored
This patch fixes the driver so that multicast PTP event messages can be recognized by the hardware time stamping unit. The station address register must be set according to the desired transport type. [ RC - Rebased Takahiro's changes and wrote a commit message explaining the changes. ] Signed-off-by:
Takahiro Shimizu <tshimizu818@gmail.com> Signed-off-by:
-
Takahiro Shimizu authored
We will let the pch_gbe code do that according to the receive time stamp filter. [ RC - Rebased Takahiro's changes and wrote a commit message explaining the changes. ] Signed-off-by:
-
Takahiro Shimizu authored
This patch clears up a few coding style issues: - Makes two function definitions a bit nicer looking. - Remove unneeded parentheses. - Simplify macros for register bits. [ RC - Rebased Takahiro's changes and wrote a commit message explaining the changes. ] Signed-off-by:
-
Takahiro Shimizu authored
The code in phc_gbe_main will need to call this method in order to set the station address register according to the receive time stamping filter. [ RC - Rebased Takahiro's changes and wrote a commit message explaining the changes. ] Signed-off-by:
-
Takahiro Shimizu authored
The reset logic after a Rx FIFO overrun will clear the programmed multicast addresses. This patch fixes the issue by reprogramming the registers after the reset. [ RC - Rebased Takahiro's changes and wrote a commit message explaining the changes. ] Signed-off-by:
-
Takahiro Shimizu authored
This patch makes logic surrounding the test of the transmit time stamping flag more readable. [ RC - Rebased Takahiro's changes and wrote a commit message explaining the changes. ] Signed-off-by:
-
Takahiro Shimizu authored
This patch fixes the helper functions that give the transmit and receive time stamps to return nanoseconds, instead of arbitrary clock ticks. [ RC - Rebased Takahiro's changes and wrote a commit message explaining the changes. ] Signed-off-by:
-
Eric W. Biederman authored
All of the users have been converted to use registera_net_sysctl so we no longer need register_net_sysctl. Signed-off-by:
Eric W. Biederman <ebiederm@xmission.com> Acked-by:
Pavel Emelyanov <xemul@parallels.com> Signed-off-by:
-
Eric W. Biederman authored
We don't use struct ctl_path anymore so delete the exported constants. Signed-off-by:
-
Eric W. Biederman authored
This results in code with less boiler plate that is a bit easier to read. Additionally stops us from using compatibility code in the sysctl core, hastening the day when the compatibility code can be removed. Signed-off-by:
-
Eric W. Biederman authored
There isn't much advantage here except that strings paths are a bit easier to read, and converting everything to them allows me to kill off ctl_path. Signed-off-by:
-
Eric W. Biederman authored
Using an ascii path to register_net_sysctl as opposed to the slightly awkward ctl_path allows for much simpler code. We no longer need to malloc dev_name to keep it alive the length of our sysctl register instead we can use a small temporary buffer on the stack. Signed-off-by:
-
Eric W. Biederman authored
Using an ascii path to register_net_sysctl as opposed to the slightly awkward ctl_path allows for much simpler code. We no longer need to malloc dev_name to keep it alive the length of our sysctl register instead we can use a small temporary buffer on the stack. Signed-off-by:
-
Eric W. Biederman authored
Using an ascii path to register_net_sysctl as opposed to the slightly awkward ctl_path allows for much simpler code. Signed-off-by:
-
Eric W. Biederman authored
Using an ascii path to register_net_sysctl as opposed to the slightly awkward ctl_path allows for much simpler code. We no longer need to malloc dev_name to keep it alive the length of our sysctl register instead we can use a small temporary buffer on the stack. Signed-off-by:
-
Eric W. Biederman authored
The sysctl core no longer natively understands sysctl tables with .child entries. Split the ipv6_table to remove the .child entries. Signed-off-by:
-
Eric W. Biederman authored
The sysctl core no longer natively understands sysctl tables with .child entries. Kill the intermediate tables and use register_net_sysctl directly to remove the need for compatibility code. Signed-off-by:
-
Eric W. Biederman authored
Don't register/unregister every ax25 table in a batch. Instead register and unregister per device ax25 sysctls as ax25 devices come and go. This moves ax25 to be a completely modern sysctl user. Registering the sysctls in just the initial network namespace, removing the use of .child entries that are no longer natively supported by the sysctl core and taking advantage of the fact that there are no longer any ordering constraints between registering and unregistering different sysctl tables. Signed-off-by:
-
Eric W. Biederman authored
sysctl no longer requires explicit creation of directories. The neigh directory is always populated with at least a default entry so this won't cause any user visible changes. Delete the ipv4_path and the ipv4_skeleton these are no longer needed. Directly register the ipv4_route_table. And since I am an idiot remove the header definitions that I should have removed in the previous patch. Signed-off-by:
-
Eric W. Biederman authored
sysctl no longer requires explicit creation of directories. The neigh directory is always populated with at least a default entry so this should cause no user visible changes. Signed-off-by:
-
Eric W. Biederman authored
On the next line we register the net_core_table in net/core which creates the directory and ensures it exists. Signed-off-by:
-
Eric W. Biederman authored
This makes it clearer which sysctls are relative to your current network namespace. This makes it a little less error prone by not exposing sysctls for the initial network namespace in other namespaces. This is the same way we handle all of our other network interfaces to userspace and I can't honestly remember why we didn't do this for sysctls right from the start. Signed-off-by:
-
Eric W. Biederman authored
register_sysctl_rotable never caught on as an interesting way to register sysctls. My take on the situation is that what we want are sysctls that we can only see in the initial network namespace. What we have implemented with register_sysctl_rotable are sysctls that we can see in all of the network namespaces and can only change in the initial network namespace. That is a very silly way to go. Just register the network sysctls in the initial network namespace and we don't have any weird special cases to deal with. The sysctls affected are: /proc/sys/net/ipv4/ipfrag_secret_interval /proc/sys/net/ipv4/ipfrag_max_dist /proc/sys/net/ipv6/ip6frag_secret_interval /proc/sys/net/ipv6/mld_max_msf I really don't expect anyone will miss them if they can't read them in a child user namespace. CC: Pavel Emelyanov <xemul@openvz.org> Signed-off-by:
-
Eric W. Biederman authored
If the netfilter code is modified to use register_net_sysctl_table the kernel fails to boot because the per net sysctl infrasturce is not setup soon enough. So to avoid races call net_sysctl_init from sock_init(). Signed-off-by:
-
Eric W. Biederman authored
Implementation limitations of the sysctl core won't let /proc/sys/net reside in a network namespace. /proc/sys/net at least must be registered as a normal sysctl. So register /proc/sys/net early as an empty directory to guarantee we don't violate this constraint and hit bugs in the sysctl implementation. Signed-off-by:
-
Eric W. Biederman authored
Right now all of the networking sysctl registrations are running in a compatibiity mode. The natvie sysctl registration api takes a cstring for a path and a simple ctl_table. Implement register_net_sysctl so that we can register network sysctls without needing to use compatiblity code in the sysctl core. Switching from a ctl_path to a cstring results in less boiler plate and denser code that is a little easier to read. I would simply have changed the arguments to register_net_sysctl_table instead of keeping two functions in parallel but gcc will allow a ctl_path pointer to be passed to a char * pointer with only issuing a warning resulting in completely incorrect code can be built. Since I have to change the function name I am taking advantage of the situation to let both register_net_sysctl and register_net_sysctl_table live for a short time in parallel which makes clean conversion patches a bit easier to read and write. Signed-off-by:
-
-
- 20 Apr, 2012 11 commits
-
-
Huang, Xiong authored
MDIO_REG_ADDR_MASK is already applied in function atl1c_write_phy_reg and atl1c_read_phy_reg Signed-off-by:
xiong <xiong@qca.qualcomm.com> Tested-by:
Liu David <dwliu@qca.qualcomm.com> Signed-off-by:
-
Huang, Xiong authored
l2cb 1.1 hardware has a bug for magic wakeup, the workaround is to add pattern enable. WoL related registers are refined as well. Signed-off-by:
-
Huang, Xiong authored
bit PCIE_PHYMISC_FORCE_RCV_DET is only for l1c&l2c to fix WoL issue, other chips set bit5 of REG_MASTER_CTRL --- this way could save more power than the former, and the bit should be kept all time. l2cb 1.x has special setting for L0S/L1 l2cb 1.x & l1d 1.x should clear Vendor Message on some platforms, otherwise it will cause the root complex hang. Signed-off-by:
-
Huang, Xiong authored
some platforms(BIOS or OS) may change ASPM configuration in PCI Express Link Control Register directly and dynamically regardless the device driver installation. Checking if ASPM support during the driver init phase by reading PCI Express Link Contrl Register doesn't make sense. This refine/update assume L0S/L1 is defalut enabled as hw->ctrl_flags inited. atl1c_set_aspm will set real configuration based on chip capability to hardware register. atl1c_disable_l0s_l1 and register definition of REG_PM_CTRL are refined as well. Signed-off-by:
-
Huang, Xiong authored
bit MASTER_CTRL_CLK_SEL_DIS could be set before enter suspend clear it after resume to enable pclk(PCIE clock) switch to low frequency(25M) in some circumstances to save power. Signed-off-by:
-
Huang, Xiong authored
refine/update register REG_MASTER_CTRL definition according with hardware spec. Signed-off-by:
-
Huang, Xiong authored
clear PCIE error status (error log is write-1-clear). REG_PCIE_UC_SEVERITY is removed as it's a standard pcie register, and using kernle API to access it. Signed-off-by:
-
Huang, Xiong authored
dmar_dly_cnt and dmaw_dly_cnt aren't used by hardware/driver any more. Signed-off-by:
-
Huang, Xiong authored
atl1c_configure_tx used a wrong value of MAX_TX_OFFLOAD_THRESH(9KB) for TSO threshold. the right value should be 7KB Fast Ethernet controller doesn't support Jumbo frame. Signed-off-by:
-
Huang, Xiong authored
l1c_wait_until_idle is called for serval modules (TXQ/RXQ/TXMAC/RXMAC). specific moudle have specific idle/busy status in reg REG_IDLE_STATUS. the previous code return wrongly if all modules are in idle status, regardless the 'stop' action is applied on individual module. Refine the reg REG_IDLE_STATUS definition as well. Signed-off-by:
-
Huang, Xiong authored
threshold setting to control ASPM for diff chips are different. currently, all gigabit-capability chips have limited-ASPM under 100M throughput. Signed-off-by:
-
