add event thread to execute events serially from event queue. Also
timeout mode is supported  which allow an event be deferred to be
executed at later time. Both link and phy compliant tests had been
done successfully.

Changes in v2:
-- Fix potential deadlock by removing redundant connect_mutex
-- Check and enable link clock during modeset
-- Drop unused code and fix function prototypes.
-- set sink power to normal operation state (D0) before DPCD read

Changes in v3:
-- push idle pattern at main link before timing generator off
-- add timeout handles for both connect and disconnect

Changes in v4:
-- add ST_SUSPEND_PENDING to handles suspend/modeset test operations
-- clear dp phy aux interrupt status when ERR_DPPHY_AUX error
-- send segment addr during edid read
-- clear bpp depth before MISC register write

Changes in v5:
-- add ST_SUSPENDED to fix crash at resume

Changes in v6:
-- at msm_dp_display_enable() do not return until resume_done to avoid
   kms commit timeout
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Configure HPD registers in DP controller and
enable HPD interrupt.

Add interrupt to handle HPD connect and disconnect events.

Changes in v8: None
Signed-off-by: Tanmay Shah <tanmay@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Add display port support in DPU by creating hooks
for DP encoder enumeration and encoder mode
initialization.

changes in v2:
	- rebase on [2] (Sean Paul)
	- remove unwanted error checks and
	  switch cases (Jordan Crouse)

[1] https://lwn.net/Articles/768265/
[2] https://lkml.org/lkml/2018/11/17/87

changes in V3:
-- Moved this change as part of the DP driver changes.
-- Addressed compilation issues on the latest code base.

Changes in v6:
-- Fix checkpatch.pl warning

Changes in v7: Remove depends-on tag from commit message.

Changes in v8: None

Changes in v9: None
Signed-off-by: Jeykumar Sankaran <jsanka@codeaurora.org>
Signed-off-by: Chandan Uddaraju <chandanu@codeaurora.org>
Signed-off-by: Vara Reddy <varar@codeaurora.org>
Signed-off-by: Tanmay Shah <tanmay@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Add the needed DP PLL specific files to support
display port interface on msm targets.

The DP driver calls the DP PLL driver registration.
The DP driver sets the link and pixel clock sources.

Changes in v2:
-- Update copyright markings on all relevant files.
-- Use DRM_DEBUG_DP for debug msgs.

Changes in v4:
-- Update the DP link clock provider names

Changes in V5:
-- Addressed comments from Stephen Boyd, Rob clark.

Changes in V6:
-- Remove PLL as separate driver and include PLL as DP module
-- Remove redundant clock parsing from PLL module and make DP as
   clock provider
-- Map USB3 DPCOM and PHY IO using hardcoded register address and
   move mapping form parser to PLL module
-- Access DP PHY modules from same base address using offsets instead of
   deriving base address of individual module from device tree.
-- Remove dp_pll_10nm_util.c and include its functionality in
   dp_pll_10nm.c
-- Introduce new data structures private to PLL module

Changes in v7:

-- Remove DRM_MSM_DP_PLL config from Makefile and Kconfig
-- Remove set_parent from determin_rate API
-- Remove phy_pll_vco_div_clk from parent list
-- Remove flag CLK_DIVIDER_ONE_BASED
-- Remove redundant cell-index property parsing

Changes in v8:

-- Unregister hardware clocks during driver cleanup

Changes in v9:

-- Remove redundant Kconfig option DRM_MSM_DP_10NM_PLL

Changes in v10:

-- Limit 10nm PLL function scope
Signed-off-by: Chandan Uddaraju <chandanu@codeaurora.org>
Signed-off-by: Vara Reddy <varar@codeaurora.org>
Signed-off-by: Tanmay Shah <tanmay@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Add the needed displayPort files to enable DP driver
on msm target.

"dp_display" module is the main module that calls into
other sub-modules. "dp_drm" file represents the interface
between DRM framework and DP driver.

Changes in v12:

-- Add support of pm ops in display port driver
-- Clear bpp depth bits before writing to MISC register
-- Fix edid read

Previous Change log:
https://lkml.kernel.org/lkml/20200818051137.21478-3-tanmay@codeaurora.org/Signed-off-by: Chandan Uddaraju <chandanu@codeaurora.org>
Signed-off-by: Vara Reddy <varar@codeaurora.org>
Signed-off-by: Tanmay Shah <tanmay@codeaurora.org>
Co-developed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Abhinav Kumar <abhinavk@codeaurora.org>
Co-developed-by: Kuogee Hsieh <khsieh@codeaurora.org>
Signed-off-by: Kuogee Hsieh <khsieh@codeaurora.org>
Co-developed-by: Guenter Roeck <groeck@chromium.org>
Signed-off-by: Guenter Roeck <groeck@chromium.org>
Co-developed-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

The constant N value (0x8000) is used by i915 DP
driver. Define this value in dp helper header file
to use in multiple Display Port drivers. Change
i915 driver accordingly.

Change in v6: Change commit message
Signed-off-by: Chandan Uddaraju <chandanu@codeaurora.org>
Signed-off-by: Vara Reddy <varar@codeaurora.org>
Signed-off-by: Tanmay Shah <tanmay@codeaurora.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>

As newer GPU families are added it makes less sense to maintain a
"generic" version functions for older families. Move adreno_submit()
and get_rptr() into the target specific code for a2xx, a3xx and a4xx.
Add a parameter to adreno_flush to pass the target specific WPTR register
instead of relying on the generic register.

All of this gets rid of the last of the REG_ADRENO offsets so remove all
all the register definitions and infrastructure.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Support the WHERE_AM_I opcode for the A618, A630 and A640 GPUs if the
microcode supports it. The WHERE_AM_I opcode allows the RPTR shadow
to be updated in priviliged memory which protects the shadow from being
read or written from user submissions.

A650 already supports extended APRIV have built in hardware support for
to access privilged memory from the CP and can go back to using the
hardware RPTR shadow feature.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Newer microcode versions have support for the CP_WHERE_AM_I opcode which
allows the RPTR shadow memory to be marked as privileged to protect it
from corruption. Move the RPTR shadow into its own buffer and protect it
it if the current microcode version supports the new feature.

We can also re-enable preemption for those targets that support
CP_WHERE_AM_I. Start out by preemptively assuming that we can enable
preemption and disable it in a5xx_hw_init if the microcode version comes
back as too old.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

In $debugfs/gem we already show any vma(s) associated with an object.
Also show process names if the vma's address space is a per-process
address space.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Add support for using per-instance pagetables if all the dependencies are
available.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Akhil P Oommen <akhilpo@codeaurora.org>

Add support for allocating private address space instances. Targets that
support per-context pagetables should implement their own function to
allocate private address spaces.

The default will return a pointer to the global address space.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Add support to create a io-pgtable for use by targets that support
per-instance pagetables. In order to support per-instance pagetables the
GPU SMMU device needs to have the qcom,adreno-smmu compatible string and
split pagetables enabled.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Use the aperture settings from the IOMMU domain to set up the virtual
address range for the GPU. This allows us to transparently deal with
IOMMU side features (like split pagetables).
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Now that we can get the ctx from the submitqueue, the extra arg is
redundant.
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
[split out of previous patch to reduce churny noise]
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Each submitqueue is attached to a context. Add a pointer to the
context to the submitqueue at create time and refcount it so
that it stays around through the life of the queue.
Co-developed-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>

This will be populated by adreno-smmu, to provide a way for coordinating
enabling/disabling TTBR0 translation.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>

In a later patch, the drvdata will not directly be 'struct msm_gpu *',
so add a helper to reduce the churn.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>

This interface will be used for drm/msm to coordinate with the
qcom_adreno_smmu_impl to enable/disable TTBR0 translation.

Once TTBR0 translation is enabled, the GPU's CP (Command Processor)
will directly switch TTBR0 pgtables (and do the necessary TLB inv)
synchronized to the GPU's operation.  But help from the SMMU driver
is needed to initially bootstrap TTBR0 translation, which cannot be
done from the GPU.

Since this is a very special case, a private interface is used to
avoid adding highly driver specific things to the public iommu
interface.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>

Currently it doesn't matter, since we free the ctx immediately.  But
when we start refcnt'ing the ctx, we don't want old dangling list
entries to hang around.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>

It's allocating an array of a6xx_gpu_state_obj structure rathor than
its pointers.

This patch fix it.
Signed-off-by: Zhenzhong Duan <zhenzhong.duan@gmail.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>

The function iommu_domain_alloc returns NULL on platforms without IOMMU
such as msm8974. This resulted in PTR_ERR(-ENODEV) being assigned to
gpu->aspace so the correct code path wasn't taken.

Fixes: ccac7ce3 ("drm/msm: Refactor address space initialization")
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Signed-off-by: Rob Clark <robdclark@chromium.org>

This adds support for the 7nm ("V4") DSI PHY/PLL for sm8150 and sm8250.

Implementation is based on 10nm driver, but updated based on the downstream
7nm driver.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> (SM8250)
Signed-off-by: Rob Clark <robdclark@chromium.org>

This allows DSI driver to work with sm8150 and sm8250. The sdm845 config
is re-used as the config is the same.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> (SM8250)
Signed-off-by: Rob Clark <robdclark@chromium.org>

The clk_pre/clk_post values in shared_timings are used instead, and these
are unused.
Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org> (SM8250)
Signed-off-by: Rob Clark <robdclark@chromium.org>

Since commit 9495b7e9 ("driver core: platform: Initialize dma_parms
for platform devices"), struct platform_device already provides a
dma_parms structure, so we can save allocating another one.

Also the DMA segment size is simply a size, not a bitmask.
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Rob Clark <robdclark@chromium.org>

This reduces the spam in dmesg when we start hitting the shrinker, and
replaces it with something we can put on a timeline while profiling or
debugging system issues.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Reviewed-by: Kristian H. Kristensen <hoegsberg@google.com>

Technically the GMU specific one is a bit redundant, but it was useful
to track down a bug.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>

This function is called quite often if you have a blinking cursor on the
screen, hello page flip. Let's drop this debug print here because it
means enabling the print via the module parameter starts to spam the
debug console.

Cc: Abhinav Kumar <abhinavk@codeaurora.org>
Cc: Jeykumar Sankaran <jsanka@codeaurora.org>
Cc: Jordan Crouse <jcrouse@codeaurora.org>
Cc: Sean Paul <seanpaul@chromium.org>
Fixes: 25fdd593 ("drm/msm: Add SDM845 DPU support")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

The cstate->num_mixers member is only set to a non-zero value once
dpu_encoder_virt_mode_set() is called, but the atomic check function can
be called by userspace before that. Let's avoid the div-by-zero here and
inside _dpu_crtc_setup_lm_bounds() by skipping this part of the atomic
check if dpu_encoder_virt_mode_set() hasn't been called yet. This fixes
an UBSAN warning:

 UBSAN: Undefined behaviour in drivers/gpu/drm/msm/disp/dpu1/dpu_crtc.c:860:31
 division by zero
 CPU: 7 PID: 409 Comm: frecon Tainted: G S                5.4.31 #128
 Hardware name: Google Trogdor (rev0) (DT)
 Call trace:
  dump_backtrace+0x0/0x14c
  show_stack+0x20/0x2c
  dump_stack+0xa0/0xd8
  __ubsan_handle_divrem_overflow+0xec/0x110
  dpu_crtc_atomic_check+0x97c/0x9d4
  drm_atomic_helper_check_planes+0x160/0x1c8
  drm_atomic_helper_check+0x54/0xbc
  drm_atomic_check_only+0x6a8/0x880
  drm_atomic_commit+0x20/0x5c
  drm_atomic_helper_set_config+0x98/0xa0
  drm_mode_setcrtc+0x308/0x5dc
  drm_ioctl_kernel+0x9c/0x114
  drm_ioctl+0x2ac/0x4b0
  drm_compat_ioctl+0xe8/0x13c
  __arm64_compat_sys_ioctl+0x184/0x324
  el0_svc_common+0xa4/0x154
  el0_svc_compat_handler+0x

Cc: Abhinav Kumar <abhinavk@codeaurora.org>
Cc: Jeykumar Sankaran <jsanka@codeaurora.org>
Cc: Jordan Crouse <jcrouse@codeaurora.org>
Cc: Sean Paul <seanpaul@chromium.org>
Fixes: 25fdd593 ("drm/msm: Add SDM845 DPU support")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Tested-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>

We could get a vblank event racing with the current atomic commit,
resulting in sending the pageflip event to userspace early, causing
tearing.  On the other hand, complete_commit() ensures that the
pending flush is complete.
Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>

XX_print like pfp_print/me_print/meq_print/roq_print are just
used in file a5xx_debugfs.c. And these function always return
0, this return value is meaningless.
This change is to make the code a bit more readable.
Signed-off-by: Bernard Zhao <bernard@vivo.com>
Reviewed-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Now that it isn't causing problems to use dma_map/unmap, we can drop the
hack of using dma_sync in certain cases.
Signed-off-by: Rob Clark <robdclark@chromium.org>

MSM bus scaling has moved on to use interconnect framework
and downstream bus scaling apis are not present anymore.
Remove them as they are nop anyways in the current code,
no functional change.
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

MSM bus scaling has moved on to use interconnect framework
and downstream bus scaling apis are not present anymore.
Remove them as they are nop anyways in the current code,
no functional change.
Signed-off-by: Sai Prakash Ranjan <saiprakash.ranjan@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

This change adds support to scale src clk and bandwidth as
per composition requirements.

Interconnect registration for bw has been moved to mdp
device node from mdss to facilitate the scaling.

Changes in v1:
 - Address armv7 compilation issues with the patch (Rob)
Signed-off-by: Kalyan Thota <kalyan_t@codeaurora.org>
Reviewed-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Disable the RPTR shadow across all targets. It will be selectively
re-enabled later for targets that need it.

Cc: stable@vger.kernel.org
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

Temporarily disable preemption on a5xx targets pending some improvements
to protect the RPTR shadow from being corrupted.

Cc: stable@vger.kernel.org
Signed-off-by: Jordan Crouse <jcrouse@codeaurora.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>